Technical Specs

sDot IC Manual
date
2019-12-23
scale
1:1 / no size
Clarita-Bernhard-Str. 18, 81249 München, Germany | [e-mail] |
sDot IC
sDot IC
Installation
smart things solutions GmbH
Clarita-Bernhard-Str. 18
81249 München, Germany
www.smart-things.com
sDot-21-0100 Manual sDot IC
TQS 9xxxxx.0100
format 550 x 170 mm, folded as leporello 110 x 170
paper ~120 g/m2, matte
420
The two parts of sDot – Charger and Pad – need
to be placed exactly inline with each other.
Use our Positioning tool to reach this very easily.
Press on the adhesive strips to x the templates
really well.
Remove the magnets.
Tear out the inside of the template on
and under the table top.
Make sure the templates don't move.
Enjoy!
Stick,
plug,
charge.
You can now stick the sDot pad on the table.
The charger can now also be glued on the
underside of the table top.
Turn the charger so that the connection of the
cable points in the desired direction
Now connect the charger to the socket and then
you can already charge your mobile phone..
Do not place bank or ID cards with magnetic
stripe or chips next to the sDot.
Do not place any metallic objects on the charging
pad.
For the most actual informations please visit
www.smart-things.com/products/sDot
We are glad that you have chosen
sDot! We have designed this
inductive charger so that
retrotting into existing furniture is
easily possible. sDot consists of two
components: the actual charger,
which is glued or screwed under the
tabletop and the very thin charging
pad, which is glued to the table.
sDot IC charges Qi compatible
mobile phones or even
earphones with table tops or
tops of furniture up to 32 mm
thick. Of course, metallic plates
are excluded. Stick, infect, load!
Ankleben, anstecken, laden!
Here the power supply
is connected.
Normally, sDot should work just ne.
If sDot does not work as desired, the
integrated LED in the sDot Charger may help.
It is important that the sDot Charger and the
sDot Pad are positioned exactly one above
the other.
You will nd detailed instructions on this on
the backside.
You can also nd a video about sDot IC at
www.smart-things.com/sDot.
Have fun with sDot!
LED blinking = searching for connection to phone
LED constant = connection ok, charging
LED off = no power
sDot Pad
with customizable inlay
sDot Charger
Long Distance Wireless Charger
Long Distance Wireless Charger
Designed in Germany • Made in China
1 2 3 4
LED indication
Positioning Tool
these two adhesive templates help you to
place the charger and pad exactly concentric
on top of each other.
Push both magnets to the place where the wireless
charger is to be placed later. The large magnet
must be above the table top, the small one below.
Big magnet
Small magnet
Place the cardboard
stencils on the
magnets and stick the
stencils on the top
and bottom of the
table top.
Technical specication
Type: sDot IC 35-0100s
Input: 19 V, 1Amp
Output: 5W max.
sDot Power Adaptor: 110 -230V AC, 50/60Hz
Dimensions
sDot ø 126 x 22mm
Cable length 150 cm
Wood
Particle Board
Corian
Laminate
Stone
Glass
Foreign Object
Detection
FOD
Over Heat
Protection
OHP
Over Voltage
Protection
OVP
Short Circuit
Protection
SCP
20 - 32 mm
0.8“ – 1.2“
Take the cardboard templates, remove the protective
film from the adhesive strips.
Place the cardboard stencils on the magnets and stick
the stencils on the top and bottom of the table top.