ASSEMBLY INSTRUCTIONS METAL GARDEN SHED E-mail: hofficeservice@gmail.com Metal Garden House Installation Tutorial https://youtu.
SITE PREPARATION Level the ground surface. ent cem Recommendation: Construct a wooden or concrete base as a foundation. The external dimensions of the product : 74.8’’ 48’’ 74.
BEFORE STARTING ASSEMBLY Remove all of the pieces from the 2 packages and spread them out on the ground. Before installation, please check the type and quantity of parts first. It is recommended to use a clean work surface to spread the parts out and for pre-assembly steps. Review all instructions before you begin, continue to refer to instructions during assembly. Be sure to follow all steps thoroughly. Please prepare these components in advance at the beginning of each stage.
ROOF PARTS C3 X4 A1 X2 A2 X2 GE X2 GC X4 M6 X1 M1 X2 M12 X2 M7 X2 M8 X2 PS1 X2 PS2 X2 PS3 X2 PS4 X2 04
WALL PARTS W1A X7 WS2A X4 WS3A X2 ULA X1 BS1 X1 C2 X4 BS2 X1 GS X2 US1 X1 V1 X50 US2 X1 V2 X180 UR1 X1 UF1 X2 BS1L X1 BS2L X1 US1R X1 US2L X1 BF3 X2 05
DOOR PARTS DLA X1 20 X4 DC X2 DG X1 DH X4 DF X1 DRA X1 DX2 X4 SCREW cm 1 inch 2 0.5 3 1 1 inch M4*10 2 3 0.5 cm For GC inch 1 F5(X4) inch 3 1 0.5 1 3 1 0.5 4 1.5 M4*16 06 4 1.5 M4*10 2 F4(X5) M5*12 2 0.5 cm 1.5 F3(X32) 2 F2(X14) 4 1 1 inch 1.5 F1(X240) cm cm 4 3 1 4 1.
GC M8 GE PS2 M12 PS1 GC M7 M6 PS4 PS3 PS3 GC PS1 M7 PS4 GE PS2 M12 M8 GC A2 C3 A1 A1 C3 M1 M1 C3 C3 A2 C2 US2L GS UF1 WS2A W1A US2 W1A W1A W1A WS3A C2 W1A WS2A BF3 C2 BS2 BS1L BS2L US1 BS1 20 BF3 WS2A 20 UF1 GS US1R DLA DF W1A C2 DG DRA W1A ULA 20 WS3A WS2A 20 UR1 07
CONTENTS Bottom frame 09-11 (page) Wall 12-22 (page) Roof 22-28 (page) Door 29-36 (page) 08
STEP 1 F1 BS1 BS1 BS1L BS1 F1 BS1L F1 X2 STEP 2 F1 BS2 BS2 BS2L BS2L BS2 F1 BS2L 09 F1 X2
STEP 3 F1 BF3 BS1L BS1L BF3 BF3 BS1 BS1L F1 X2 STEP 4 BS2L BS2 F1 BF3 BS2 BS2 BF3 BF3 BS1L BS1 10 F1 X2
STEP 5 F1 BS2L BS2L BF3 BF3 BS2L BS2 BF3 BF3 BS1 BS1L F1 X2 STEP 6 BS2L BS2 BF3 BF3 BS1 BS1L F1 BS1 BS1 BF3 11 BF3 F1 X2
STEP 7 F1 Tips: Align the gasket with the hole, and then use the electric drill to drill the V2 into the hole. V2 STEP 8 Please align the screws with the screw holes for installation.
STEP 9 WS2A F1 WS2A V2 BS1 F1 X3 V2 X3 STEP 10 F1 WS2A V2 BS1 13 F1 X4 V2 X4
STEP 11 WS2A F1 V2 BS1 V2 X4 F1 X4 STEP 12 C2 US1R C2 US1 GS C2 US1 US1 GS 14 US1R C2
STEP 13 × √ Note: Connector must fit.
STEP 15 US1R C2 US2L C2 US1R GS C2 US2 US1R C2 C2 STEP 16 F1 V2 x2 BS1 16 F1 X6 V2 X6
STEP 17 Note: Pay attention to distinguishing the direction when installing.
STEP 19 UR1 UR1 ULA ULA BS1 STEP 20 F1 V2 F1 ULA ULA V2 F1 18 F1 X4 V2 X2
STEP 21 V2 F1 UR1 F1 F1 UR1 V2 F1 F1 X4 V2 X2 STEP 22 V2 F1 W1A W1A WS3A 19 F1 X20 V2 X20
STEP 23 W1A W1A WS3A STEP 24 W1A W1A WS3A V2 F1 20 F1 X20 V2 X20
STEP 25 W1A W1A WS3A STEP 26 F1 F1 V2 W1A W1A W1A W1A W1A W1A 21 F1 X24 V2 X24
STEP 27 W1A W1A W1A STEP 28 A1 A2 C3 F2 22 x2 F2 X4
STEP 29 M1 F2 M1 Note: Do not tighten F2 yet. F2 X6 STEP 30 75.
STEP 31 A1 M1 A2 A2 M1 A1 STEP 32 M1 Note: Finally tighten all F2.
STEP 33 BE1 F1 V2 BE1L F1 X16 V2 X16 STEP 34 Note: Do not install F1 and V2 in the holes near the outer side of PS3.
STEP 35 F1 V2 PS2 PS2 PS1 PS4 Tips: Install PS4, PS1, PS2 in order. PS3 Note: Do not install F1 and V2 in the holes near the outer side of PS2. F1 X18 V2 X18 STEP 36 F1 PS2 V2 Note: Do not install F1 and V2 in the holes near the outer side of PS2.
STEP 37 PS3 PS3 PS1 PS2 PS4 Tips: Install PS4, PS1, PS3 in order. Note: Do not install F1 and V2 in the holes near the outer side of PS3.
STEP 39 GE F1 M6 GE F1 X6 STEP 40 GC M12 F5 GC GC GC M12 M12 GC X4 28 F5 X4
STEP 41 20 DC DX2 DF DLA DX2 DC 20 STEP 42 20 20 DX2 DLA Note: Make clear the front and back of the door panel.
STEP 43 V2 F1 outside inside outside DF F4 F1 X8 30 V2 X8 F4 X2
M744 STEP V2 F1 F1 DH DX2 DLA F1 DX2 DH F1 F1 F3 X2 F1 X6 31 V2 X6 F3 X8
STEP 45 DC DC DC F1 DC F1 X8 32
STEP 46 20 DX2 DG DRA DX2 20 33
STEP 47 20 20 DRA DX2 Note: Make clear the front and back of the door panel.
STEP 49 20 F1 DH F3 DX2 F1 X2 DRA DX2 DH de 20 F1 X6 35 V2 X6 F3 X8
STEP 50 DRA DLA UR1 F3 DRA X4 F3 X16 36
STEP 51 V1 V2 F1 Put it on the screw tip to prevent injury.
CARE & SAFETY • Unsuitable for storage of flammable or corrosive substances. • It is of utmost importance to assemble all of the parts according to the directions. Do not skip any step. • Please consult your local authorities if any permits are required to erect shed. • Periodically check shed to assure that it remains stable and that the site remains level.