Index Definitions-+ Factory Default Settings: Impotent Notes Change Master Code Add Credential Add a User Code Add Multiples User Codes Add User Key cards Delete Transcendentalists Riser Code Delete User Key card Reset to Factory Default Settings System Settings Passage Mode Verification Mode Sound Reset fo Factory Default Set ti Low Battery YW1949 1
Definitions Credential: The lock requires a valid credential to operate. A credential can be a 6-10 digit Master Code, User Code, or Keyboarder, LED Indicator: The LED Indicators are located around the keypad of the lock. Lock flashes green LED landlord red LED dependent on inputs. While unlocking, a red LED followed by a free; LED means the lack is not programmed and can be unlocked with any 6-10 digit code or Keyboardists.
Important Notes » To wake up the touch keypad, gently swipe or fap the keypad. » While In Factory Default Settings any credential will open the lock until a Master Code Is programmed Into the lock. When any credential is presented the lock will flash red, then green, and unlock. » The Factory Default Offing's Master Code must be changed before programming any other codes or system settings. » A Master Code or User Code can be 8-10 digits (they do not need to be the mass code length).
Change Master Code Te (msl w+ 1 En] [EEE wt For example, to change Master Code to press: * SEAR R086 Obsess 4 Factory Default Setting’s Master Code is 123456. It must bw changed with the user's own Master Code immediately. Manufacturer assumes no liability, direct or indirect, dus to failure to change Master Code. No thee programming wil ba accepted until Factory Default Setting's Master Code hs bean changed. Master Coda can be changed at any ime.
Add Multiple User Codes Key Sequence 1% User Code Key Sequence » 3 dis [Master Code. Additional User Codes Key Sequence: For example, to add User Codes “2020207, “303030°, and "404040", press: “HOES 553585 Snots «The input of additional credentials must start before lock goes into rue user one 11H * Crass hoe venue 1) * (carcass 282020 fH 3 202020 [# 303038 1 * $8080 IH 404040 | aot0m0 1%) die Mods (12 abscond.
Delete Credentials ol say courser [14] » I 20207, assuming ths Master Cods Is pass ET [ee JE Delete User Codes Key Sequence Nestor God For example, to desists User Code “20: + oy | abuses Elate User Key Cards Key Sequence {aster Cote Lop Bs [i] ves [TEE eg + The Master Code cannot be deleted. + Multipart Keyboardist can be deleted during the same programming sausage (ike Additional User Codes Kay Sequence) «To ext, pass the asterisk or Walt unt tha lack goes Into Idle Mode (12 seconds).
System Settings Passage Mode Key Sequence BB Eel wt Notes Dual Verification Mode Key Notes Adjust Keypad Sound Key We Notes Master Code Tame A 0 Passage db Ho meld oti [0 Hew -lowbrow After creating a Passage Code or key card, presenting it will activate the Passage Mode function The lock will remain actively unlocked uni the Passage Code or skyward or Master Cods Ia entered fo disables the function Passage Mode and Dual Verification Mod cannot be programmed simultaneously.
Reset Lock to Factory Default Settings without a Master Code Stops Unscrew the back cover. . Locate the reset button on the battery holder. Press and hold the reset button. After approximately 4 seconds, the lock will beep 2 dimes and you can release the reset button. The green LED indicator will it up and it will beep 1 ime indicating lock is reset.
Hy Dowser CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED ESPALIER ACCORDING TO THE INSTRUCTIONS. jamming: This equip; men has been tested and found to comply with the limits for a Class B digital device, pursuant te part 15 of the FCC Rules. These limits are designed to pi le reasonable protection against harmful Interference In a Residential installation.