E481323 TP108MB Smart Battery Charger 2 / 10 / 25 AMP 2A/1 0A/2 SELE 5 A/ AUT O CTABL E 2A TRICKL E CHAR REC OND GE STAND ARD SELE /AGM/G CTABL E L E ITION ASSIST 10A QUIC K CHAR GE ENGINE START 25A BOOS T CHAR GE
Table of Contents Intended Use 1 Specifications 1 Important Safety Information 2 Main Parts of Product 8 Before Each Use 9 Operating Instructions 10 Maintenance 16 Troubleshooting 16 WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Should you have any questions or need any support, please contact us at support.us@51towertop.
Intended Use This Battery charger is suitable for 12V Lead-acid Batteries, including GEL, AGM and STD. This Battery charger will quickly and easily charge the vehicle battery and keep the battery performing at its optimal while lasting longer. This Battery charger has an interactive LCD display showing charging rate, battery type, error message in words and icon.
Overtime Charging Protection - If the battery cannot be fully charged within 24 hours, charger will stop charging automatically. Short Circuit Protection - if the cables connected suffer from short circuit when the charger working, charger will stop charging automatically. Important Safety Information • Risk of Explosive Gases, Electric Shock or Fire. • Keep out of reach of children.
• Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. • Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. • To reduce risk of electric shock, unplug charger from outlet before attempting any repairs or cleaning. Turning off controls will not reduce this risk.
PERSONAL SAFETY • Make sure that someone is within range of your voice to come to your aid if needed while you work with or are near a lead-acid battery. • Wear complete eye and clothing protection when working with lead-acid batteries. • Avoid touching your eyes while working with a battery. Have plenty of fresh water and soap nearby for use in case battery acid contacts your eyes, skin or clothing. If this happens, wash immediately with soap and water, then get medical attention.
ELECTRICAL SAFETY • Never alter AC cord or plug provided. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Improper connection can result in a risk of fire or electric shock. • Do not operate charger with damaged cord/plug - replace the cord/plug immediately. • “Warning: Changes or modifications to this unit not expressly approved by the party responsible for compli ance could void the user’s authority to operate the equipment.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV techni cian for help.” • NOTE: If using this battery charger/maintainer for a marine battery, the battery must be removed and charged on shore unless you have purchased special equipment designed for marine use to allow for onboard charging.
• Place the free end of the battery cable as far away from the battery to be charged as the cable will allow and then connect the black negative (-) charger clip to the free end of the cable. NEVER face the battery when making the connection. • When disconnecting the charger/maintainer, always use the reverse order from the connection process, staying as far away as possible from the battery. AC POWER CORD/PLUG CONNECTIONS AND PROPER GROUNDING • This battery maintainer is designed for use on a 120V circuit.
Main Parts of Product 2 3 2A/1 0A/2 SELE 5A/AUTO CTABLE 2A TRICKL RECOND GE ITION ASS 10A QUIC No. STANDA RD/ SELECT AGM/GE L ABLE E CHAR 4 1 K CHAR GE IST ENG INE STA RT 25A BOOS T CHAR GE 56 Subassembly 1 LCD Display Window - shows charging status, charging current, voltage, battery type, start aid and error information in words and icon. 2 Charging Amp Selection Button - press to select the charging rate from 2A, 10A, 25A and automatic charging rate.
No. 6 Subassembly Start Aid Button - press to activate engine start function. LCD display window will guide how to proceed step by step and press again to stop Before Each Use SHIELD EYES: Explosive gases can cause eye injury or blindness. CONTAINS SULFURIC ACID: May cause severe burns and blindness. If it is necessary to remove the battery prior to charging, always remove the grounded terminal first. Ensure all electrical accessories are off prior to charging.
Read individual precautions and warnings outlined by the battery manufacturer relative to charging / maintaining. Ensure that charger clips make a tight connection. NEVER smoke or allow a spark or flame in the vicinity of the battery or engine. Use charger for charging LEAD-ACID batteries only. NEVER charge a frozen battery. Operating Instructions SELECT CHARGING RATE This smart charger has an Optimal function (defaulted setting).
BATTERY RECONDITIONING When your battery has been unused for long periods of time, the battery will be in a deep discharged state. The battery reconditioning function is to recover the battery from deep discharge and help the battery last longer. CHARGING TIME Charging time may vary depending on some factors listed below stop the process. Battery State – Depending on the voltage of your battery, it may take up to 10 hours to charge. Batteries with higher voltage can usually be charged in a few hours.
CUPPENT VOLTAGE 7-STAGE CHARGING 1. Desulphation: Pulse charges the battery to break down the buildup of lead sulphate crystals. Lead sulphate crystals can occur when a battery has been discharged or left unused for a period of time, seriously affecting the performance and lifetime of the battery. 2. Soft Start: A slow steady buildup of the charging process that limits the power supplied to protect the battery. 3. Bulk Charge: The main part of the charge process where 80% of the charge is applied. 4.
7.Float: Maintains the battery at 100% charge without overcharging or damaging the battery, allowing the Smart Charge to be left connected to the battery indefinitely. Ideal for batteries used intermittently, such as seasonally used vehicles including classic cars, motorcycles. Note: The Float process takes 5-10 minutes to fill the battery. DO NOT disconnect the connection (AC\DC) during this time.
Press the "AMP" button to choose the desired charging rate, if you don’t know how many Amps to choose, please select automatic charging rate. Press the “BATTERY TYPE” button to select your battery type, if you are not sure, please choose “Standard”, then press the “CHARGE” button to start charging. The LCD will display as shown. Note: If user does not select the charging Amp and battery type within 30 seconds, it will start charging the battery using the default setting (auto charging rate for STD battery).
RECONDITION DISPLAY Press the "RECONDITION" button to activate the battery recondition function, the wrench image will flash and the screen will show: "BATTERY IN REPAIR NOW”. When the repair is completed, the LCD will display as shown. START AID DISPLAY Press the “START AID” button to activate this function, please wait until the LCD screen tells you to start the engine. If the battery capacity is not enough to start engine within one 120 second cycle, please press the ”START AID” button again.
Maintenance Always unplug and disconnect the charger before performing maintenance on the unit. After each use, use a dry, lint-free cloth to clean battery corrosion and other dirt from the clips, cords and charger. Ensure that all components are in good working order. Never open the charger as there are no serviceable parts inside the unit. The charger should be stored in an upright position when not in use. Store in a cool, dry location.
Failure Wrong Battery Possible Cause The charger may connect Please connect to a 12V to a 24V battery by lead acid battery. mistake. 1. Selected charging rate Overtime is too small for big battery; Charging 2. The battery condition is not good. Reverse Polarity Clamps connected to wrong polarity. The temperature of the Over Heat charger is too high Battery Failure Corrective Action 1. A short circuit inside the battery; 2. An appliance is drawing power from battery being charged. 17 1.
