Welcome to start Your mobile printing solutions 4-inch ThermalPrinter PrinterWSP TS-i451 inch Thermal Quick reference reference guide guide Quic Quick guid
WSP-i451 Introductions Thank you for purchasing a WSP-I451 product from TOUSEI. The WSP-i451 is the ideal solution for Mobile thermal printing for Receipts, Label, Tickets, and support Bluetooth, WIFI(optional), USB connection This quick reference guide is designed to help users effectively operate the device. 1. Please read this reference guide carefully before using the device for safe and proper use. 2. This device may only be used in countries where it is sold. 3.
WSP-i451 this case you cannot receive the free repair service.) 4. Please make sure that nothing rests on the power cord when connecting the power cord, and the location where the power cord will not be stepped on or cause to stumble. 5. Please backup the data and information from your device. During the repair or upgrade, there is a slight possibility of your data being erased. 6.
WSP-i451 residue clean the power cords pins thoroughly. 15. Do not paint your device and Do not place heavy or sharp objects on the LCD screen or on the device. It can damage your screen or your device’s exterior. Cleaning the device 1. Please make sure that the machine is turned off before cleaning the device. 2. Please use a soft and lint-free and dry cloth to clean the device. 3.
WSP-i451 Operating Precautions The general features of WSP-i451 printer are as follows: Compact size (153×153×63mm) Light weight(596g) for true mobility Very silent printing thru direct thermal printing method High speed (100mm/sec, MAX) High resolution (203dpi: 8dots/mm). Bluetooth, USB , Wireless LAN(IEEE802.
WSP-i451 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity.
WSP-i451 ● Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. ● Do not open the platen cover during printing. ● Do not remove or reinstall the communication cable during printing or transmission. ● Do not touch the connectors of the communication during printing. ● Switch the POWER OFF when not in use. ● Do not use other solvent. ● The AC adapter, the battery charger and the battery pack may become warm when in use.
WSP-i451 Set up the printer. 1.1. Printer & Accessories Please make sure all the above components are included.
WSP-i451 1.2. Symbol Standby symbol IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state. Direct current symbol This symbol is found on many electronic devices that either require or produce direct current. 1.3.
WSP-i451 1.4.
WSP-i451 1.5.
WSP-i451 Item Specifications Receive buffer size 64K bytes Sensor Support Cover open, Paper, Label LCD 128×32 Dots FSTN (Blue LED Backlight) Battery Rechargeable 7.
WSP-i451 1.6. Replacing paper roll. Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow direction like the picture. 3. Insert a new paper roll as shown. 4.
WSP-i451 1.7. Power supply 1.7.1. Specified power supply The following specification is requested for Power supply. Battery Charger: DC 5V/2A Avoid using power supply which its power capacity of power current is extremely high. 1.7.2. Installing the battery Warning: ● Before installing or removing the battery pack, ensure the printer is OFF. ● If the printer is not used for long period of time, remove the battery pack from the printer. ● Risk of explosion if battery is replaced by an incorrect type.
WSP-i451 1.7.3. Recharging the battery pack For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. NOTE : While charging the printer, turn off the printer power. The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases.
WSP-i451 1.8. Set operation mode The printer is powered on then In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode. FEED button: changing Printer MODE status. POWER button: changing OPTION status.
WSP-i451 OPTION MODE SELF TEST SPEED QUANLITY Print the self-test page NORMAL QUICK NORMAL THICK NO USE MARK NO USE 30 Seconds Off Power Down (PWDN) 60 Seconds Off 90 Seconds Off 120 Seconds Off 150 Seconds Off 180 Seconds Off 17
WSP-i451 2. Interface 2.1. USB The WSP-i451 printer has a USB interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed: USB Pin No. Name Function 1 VCC +5V 2 DM DATA “-” 3 DP DATA “+” 4 NC. - 5 GND Ground NOTE : ● If you connect the printer interface cable is converted to USB mode. ● When data receiving, when it removes the communication cable, it loses a data.
WSP-i451 2.2. Bluetooth Category Specification Bluetooth Spec. Bluetooth Ver5.2 / Class2 (10m) Frequency band 2402~2480㎒ Protocol L2CAP, RFCOMM, SDP Profile GAP, SDAP, SPP 2.3. Wireless LAN (optional) Category Specification Function Radio frequency transfer Module (IEEE802.11b/g/n standard conformity) Frequency band 2.4GHz Channel 1 to 13 channel Security WEP(64/128), WPA(TKIP), WPA2(AES) 2.4. Communication Protocol Sequence 2.4.1.
2.4.2. Irregular Operation (Communication Error) 500ms timeout Host Command Command Module Host Command Command is Command Executio Command Error Module CheckSumEr Executio 3. Using the printer 3.1. Control panel.
BUTTON - FEED Button : When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second. - POWER Button: ① When of 5 or more seconds presses and power comes to on or off. ② After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
WSP-i451 4. Consumable Parts. 4.1. Recommended paper. Type Paper width Paper thickness Outer diameter Recording side : Thermal Paper : 110mm : 60±5㎛ : Ø50mm or less : Outside of roll Cautions 1. 2. 3. 4. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. Chemicals or oil may change the color of paper, or printed Characters may fade. Change of paper color starts from approx 70 ℃. Pay attention to heat, humidity and sun light.
Warranty information WSP-i451 Warranty certificate TOUSEI warrants this device against defects in materials or workmanship for 12months parts from the original ship date. During this period, TOUSEI will repair or replace defective parts with new or reconditioned parts at TOUSEI option, without additional charges. Warranty conditions 1. This warranty extends only to products distributed and/or sold by TOUSEI. 2.
WSP-i451 RMA (Returning Merchandise Authorization) policy 1. If repairs are required, the customer must clearly and in detail record the devices problem on the RMA request form or email. 2. In all cases, TOUSEI has the right to evaluation and inspect the faulty device. TOUSEI will evaluation the device according to the description of the problem on the RMA request form or in the email. 3. After evaluation, Warranty or Out-of-Warranty status will be determined. 4.
WSP-i451 This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. WEEE (Waste Electrical and Electric Equipment) Symbol Information Correct disposal of this product (Waste Electrical & Electronic Equipment) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
TOUSEI ANLINX CO.,LTD. Address: 2nd floor, 248, HuaQing road, QingHu, LongHua district, Shenzhen City, China 518109 Technology support link: www.tousei.com.cn/download/ Common Trouble Shooting: www.tousei.com.cn/contact-us/ www.tousei.com.