Invisilok - M115 Reader with Remote Antenna for a Keyless Security System for Solenoids Reader Remote Antenna Keychain Key Wristband Key 57315 Nagy Dr Elkhart, IN 46517 800-294-2570 574-294-2570 www.touchtronics.
OPERATION USING A WRISTBAND KEY OR KEYCHAIN TAG Present (swipe) Wristband Key or Keychain Key to Remote Antenna. Wristband Key or Keychain Key should be swiped within 3-4 inches of antenna. • Door unlocks. • After six (6) seconds, the door automatically re-locks whether it is open or closed. • The Red LED on the antenna flashes twice and the Green LED turns ON for 6-seconds.
SYSTEM DIAGRAM This Keyless Entry System can be set up with 1 to 4 Nodes M115-R1 M115-R2 1 Node 2 Nodes Bulkhead or Curbside and Rear Doors Bulkhead Door Antenna Antenna Antenna SWITCHES SWITCHES Curbside View Curbside View Antenna M115-R3 3 Nodes M115-R4 Curbside, Bulkhead and Rear Doors Antenna Curbside Antenna 4 Nodes Curbside, Driver Side, Bulkhead and Rear Doors Antenna (Driver Side) Antenna Antenna Antenna Antenna SWITCHES Antenna SWITCHES Curbside View Curbside View WRIST
INSTALLATION X 1. Identify the location of the remote antenna on the exterior of the truck, with the exception of the bulkhead antenna. The bulkhead antenna is trypically installed on the cab side of the partition wall between the cargo and cab. 2. The antenna should be placed in a location that is about 36-48” off the ground or floor and one that is easy to access when swiping with the Wristband Key or Keychain Key. 3.
TROUBLESHOOTING - KEYLESS ENTRY 1. What to do if the door does NOT unlock when the antenna is swiped with the Wristband Key or Keychain Key: Items referred to in Troubleshooting Instructions: Switch Wristband Key Keychain Key Transfer Card Antenna (Remote) Reader Possible Cause #1: Wristband Key or Keychain Key is NOT Enrolled Correctly *Note: Door DOES Unlock When Unlock Switch is Pressed Actions To Take: • Swipe the antenna with the Wristband Key or Keychain Key.
TROUBLESHOOTING - KEYLESS ENTRY Possible Cause #4: The Wire Harness, Crimp, Ground Connection or Solenoid Has Failed Actions ToTake: • If the Red LED flashes when swiped with the Wristband Key or Keychain Key or the Unlock switch is pressed, but the door does not unlock, check the truck harness and connector. • Also check the solenoid output voltage on pin #3 (gray) which should be +12VDC any time the green LED is ON for 6-seconds.
TROUBLESHOOTING - KEYLESS ENTRY 2. What to do if the Door Does NOT Unlock When Pressing the Unlock Switch: Possible Cause #1: The Unlock Switch is Damaged or Defective *Note: the Door DOES unlock when swiped with a Key Actions To Take: • Try unlocking the door using the Wristband Key or Keychain Key. - If the door unlocks, then the unlock switch or wire harness is defective.
TROUBLESHOOTING - KEYLESS ENTRY Possible Cause #4: Antenna Has Failed Actions To Take: Pin 1 Pin 3 • If the unlock switch is OK and there is +12V on the input pin #3 (Gray wire) when the switch is pressed, unplug the antenna from the wire harness and then reconnect it.
TROUBLESHOOTING - KEYLESS ENTRY 3. What to do if the door does NOT unlock when swiped or unlock switch is pressed, but the green LED turns ON for 6-seconds: Possible Cause #1: Solenoid does not have a good ground connection Actions To Take: • Check that the ground wire to the solenoid is making good contact with the truck chassis by using a voltmeter. If there is no ground, correct the ground connection.
TROUBLESHOOTING - KEYLESS ENTRY 4. What to do if the unlock response is slow when swiped with the Wristband Key: Possible Cause #1: Data Bus Failure Due to Wire Harness or Connector Problem Actions To Take: • Swipe each antenna and observe the Red LED. -If that reader is NOT connected to the data bus, then the RED LED will continue to flash during the 6-second solenoid timer.
TROUBLESHOOTING - DATA BUS 1. What to do if the Status LEDs Flash Data Bus Failure: Possible Cause #1: Short in the Wire Harness Actions To Take: • If the harness is not shorted to power, disconnect the wire harness connector for power and ground located under the hood. • Check different points in the wire harness and see if the chassis ground is present. With the wire harness disconnected from the truck, NO ground should be detected. • If a ground is detected, locate the problem and repair it.
THERE ARE 4 DIFFERENT CONFIGURATIONS AVAILABLE FOR THE M115 SYSTEM. THE NODE'S ARE THEN IDENTIFIED BY THE GROUND CONNECTIONS OF THE LOCATION PIN'S 7 & 8. SEE TABLE BELOW FOR IDENTIFYING EACH NODE. EXAMPLE - A TRIPLE NODE SYSTEM WOULD HAVE M115-R3 LABELED ON EACH NODE, WHILE A QUAD NODE SYSTEM WOULD HAVE M115-R4 LABELED ON EACH NODE. THE (X) IN THE M115-RX LABEL IS DESIGNATED BY THE NUMBER OF NODE'S IN THE SYSTEM.
PARTS Minimum Order - $25 Call Factory For Pricing and Availability (Indiana Local: 1-574-294-2570; Toll Free: 1-800-294-2570; Fax: 1-574-293-1611) TTI Part Number Part Description M115-A Antenna, 2.
TOUCHTRONICS, INC. WARRANTY POLICES AND PROCEDURES 1. Each individual product is warranted under thePARTS TouchTronics Limited Warranty program for one (1) full year from the date of purchase or two (2) years from the date of manufacture. 2. No product will be covered under the TouchTronics Limited Warranty program that has a maunufacture date older than two (2) years. 3. To receive technical support or warranty service, call our technical support center at 1-800-294-2570 during regular business hours. 4.
NOTES NST13308-M115-02_A ◄► 2021-06-23 ◄► Page 15
NOTES NST13308-M115-02_A ◄► 2021-06-23 ◄► Page 16