User's Manual

ManualsBrandsTouchtronics ManualsElectronicsRemote Control Transmitter

Table Of Contents

Radio Frequency (RF)

Remote Control System

Service Manual

POWERTouch 1200

Manual NST11424-2

2010-04-05 Rev F

57315 Nagy Drive

Elkhart, IN 46517

T T Iouch ronics, nc.

Ph: 800-294-2570

Fx: 574-293-1611

www.touchtronics.com

touchtronics@touchtronics.com

1230-R

Harness w/

Sealing Gasket

Sealed Receiver:

Moisture & Dust

Model # P12xx-R Sealed

(see pg 2 for model number chart)

Range - 300 Feet Typical

- Up to 600 Feet

Output - 4 Relays

Optional - 7 Relays

Input - 2 (+12v) A1 & A2

Optional - 6 (+12v or Ground) B1 - B6

Frequency - 433MHz

Codes - Rolling Codes

- Secure Encryption

Voltage - 12VDC

- 24VDC

Current - 5 Amps Max per Output

- 10 Amp Input - Standard

- 30 Amp Input - Optional

Antenna - Fixed - Standard (shown)

Optional - TNC Whip

- Flex Whip / Roof Mount

- Flex Whip / Glass Mount

Harness - 9” Standard, 14 pin

Battery - All transmitter styles (except TR style)

- Coin Style, Lithium, CR2032

- 100,000 1-second pulses

- 10 year shelf life

- TR Style - 2 x “AA” Batteries

System Specifications

P1000-TM1 P1000-TM2 P1000-TM4

P1000-TK1 P1000-TK2 P1000-TK4

P1000-TF2 P1000-TF2-LK P1000-TF4

P1000-TX2 P1000-TX4 P1000-TX6

P1000-TX2S P1000-TX4S P1000-TX6S

No ON/OFF Switch

With ON/OFF Switch

P1000-TF6

TK, TF & TR Series

Sealed

Transmitters

P1000-TR4 P1000-TR3 P1000-TR2

Summary of content (4 pages)

PAGE 1
POWERTouch 1200 Harness w/ Sealing Gasket Radio Frequency (RF) Remote Control System Service Manual 1230-R Sealed Receiver: Moisture & Dust P1000-TM1 P1000-TM2 TK, TF & TR Series Sealed Transmitters P1000-TM4 P1000-TK1 P1000-TK2 P1000-TK4 P1000-TF2 P1000-TF2-LK P1000-TF4 P1000-TR4 P1000-TR3 P1000-TR2 System Specifications Model # P12xx-R Sealed (see pg 2 for model number chart) Range - 300 Feet Typical - Up to 600 Feet Output Optional - 4 Relays 7 Relays Input Optional .
PAGE 2
System Operation Each time a button is pressed on the transmitter, the corresponding output will turn On. For example, if button #1 is pressed, output #1 will turn On as long as the button is held. If an input signal is sent to inputs A1 or A2, or any inputs B1 - B6, the corresponding output will turn On as long as the signal is present. (A1 or B1 = Output #1 is ON. A2 or B2 = Output #2 is ON) Each output is factory set as momentary.
PAGE 3
Page -3- DIP Switch Options Output 7 J2-14 Output 6 J2-13 Output 5 J2-12 Out #3 Out #4 4 Out #5 5 Out #6 6 7 8 OFF = Momentary (Standard) ON = Latching (Optional) DIP Switches 1 - 6 control outputs 1 - 6 respectively: Out #2 Out #1 3 OFF 2 OFF 1 ON ON J1 J2 J3 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 Call factory for more information on other DIP switch options, including hydraulic pump, cascade and courtesy lights.
PAGE 4
TouchTronics, Inc. Warranty Policies and Procedures 1) Each individual product is warranted under the TouchTronics Limited Warranty program for 1 full year from date of purchase or a maximum of 2 years from the date of manufacture. 2) No product will be covered under the TouchTronics Limited Warranty program that has a manufacture date older than 2 years. 3) To receive technical support or warranty service, call our technical support center during regular business hours.