Service Manual

ManualsBrandsTouchtronics ManualsElectronicsBattery Powered Transmitter (FOB)

NST13308-P1000_A 2020-06-10 Page 1

57315 Nagy Dr

Elkhart, IN 46517

800-294-2570

574-294-2570

www.touchtronics.com

POWERTouch P1000 Series

Radio Frequency (RF) Remote Control System

SERVICE MANUAL

TNC Antenna

(Option)

Not Sealed

P1000-TX4S

P1000-TX6S

With ON/OFF Switch

P1000-TK1 P1000-TK2 P1000-TK4

P1000-TF2-LK P1000-TF4 P1000-TF6

P1000-TM1 P1000-TM2 P1000-TM4

Receiver can be paired to any transmitter below

TK Sealed Transmitters

TF Sealed Transmitters

TM Transmitters

TX Transmitters

P1000-TF2

P1000-TX2S

RANGE

300 feet typical

Up to 600 feet

OUTPUT

OPTIONAL

6 Relays

7 Relays

INPUT

2 (+12v) A1 & A2

6 (+12v or Ground) B1-B6

FREQUENCY 433 MHz

CODES

Rolling Codes

Secure Encryption

VOLTAGE

12 VDC

24 VDC (Special Order)

CURRENT

5 Amps Max per Output

10 Amp Input - Standard

30 Amp Input - Optional

ANTENNA

OPTIONAL

Fixed - Standard

TNC Whip (shown)

Flex Whip / Roof Mount

Flex Whip / Glass Mount

HARNESS

9" Standard, 14 Pin Connector Standard

6 Pin Connector Optional

2 Pin Connector Optional

BATTERY

All transmitter styles (except TX style)*

• Coin Style, Lithium, CR2032

• 100,000 1-second puls

• 10 year shelf life

*TX Style - 9V

SYSTEM SPECIFICATIONS

Model # P1010-R6, P1030-R

Summary of content (4 pages)

PAGE 1
POWERTouch P1000 Series TM Radio Frequency (RF) Remote Control System SERVICE MANUAL TNC Antenna (Option) Not Sealed SYSTEM SPECIFICATIONS Receiver can be paired to any transmitter below Model # P1010-R6, P1030-R TK Sealed Transmitters RANGE 300 feet typical Up to 600 feet OUTPUT OPTIONAL 6 Relays 7 Relays INPUT 2 (+12v) A1 & A2 6 (+12v or Ground) B1-B6 FREQUENCY 433 MHz CODES Rolling Codes Secure Encryption VOLTAGE 12 VDC 24 VDC (Special Order) CURRENT 5 Amps Max per Output 10 Amp Input
PAGE 2
X System Operation Each time a button is pressed on the transmitter, the corresponding output will turn On. For example, if button #1 is pressed, output #1 will turn On as long as the button is held. If an input signal is sent to inputs A1 or A2, or any inputs B1 - B6, the corresponding output will turn On as long as the signal is present. (A1 or B1 = Output #1 is ON. A2 or B2 = Output #2 is ON) Each output is factory set as momentary.
PAGE 3
X Switch Input A1, J2-1 Switch Input A2, J2-2 Logic Ground, J2-3 Logic Power, J2-4 J3 J2 Output 3 J2-10 LOGIC Output 4 J2-11 Output 5 J2-12 Output 6 J2-13 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 WHT/RED GRY/RED BLK/WHT RED/WHT NOT USED RED RED YEL ORG BLU GRN PNK VIO TAN +12V / A1 +12V / A2 CHASSIS GROUND +12V LOGIC POWER 1 2 1 2 RED NOT USED POWER / 30 AMP Output 7 J2-14 J1 Output 7 Used only with DIP Switch Option 7 & 8 +12v or GND / B1 +12v or GN
PAGE 4
X TouchTronics, Inc. Warranty Policies and Procedures 1) Each individual product is warranted under the TrouchTronics Limited Warranty program for one (1) full year form the date of purchase or a maximum of two (2) years from the date of manufacture. 2) No product will be covered under the Touchtronics Limited Warranty Program that has a manufacture date older than two (2) years.