User's Guide

TUXEDOW Home Automation and Security System
Quick Installation Guide
Full Installation Guide [Part Number 800-25176] available online at: https://mywebtech.honeywellhome.com Select the icon to access the Introduction and Training Videos.
To reset the Touchscreen, press and hold the side Power Button for 3 seconds and then press on the “Press here to Reset” message on the screen to start the reset function. The Touchscreen
can also be reset by pressing and holding the reset button for approximately 15 seconds until the touchscreen resets automatically.
TOUCHSCREEN INITIALIZATION
When initially powered, the boot sequence and the "Set ECP Address" is displayed. If using one
Touchscreen, leave the address set to 1 and select Apply. If using more than one, power-up
each Touchscreen one at a time, and set each Touchscreen address to one of the addresses
enabled in the control panel.
Language Selection - If applicable, after initial ECP selection is set, the “Languages” menu is
displayed. Select a language.
Operation Mode Selection: Select Normal Mode, Safe Mode or Demo Mode to turn the option
on or off.
Weather Forecast – Select on the Weather feature to set the weather forecast for a specific
location.
SYSTEM INFORMATION / UPGRADES
To view the current software version installed, Interface name and MAC Address, select
Setup → System Info .
Software upgrades may be available. Log in to MyWebTech (see above) and enter the model
name in the “Search by” “My Product” field. Select Go; click on Touchscreen software update
SBS”.
ECP ADDRESS
If the screen is displaying “ECP Error”, the ECP address in the Touchscreen is not valid for the
panel that it is connected to. In this case, to change the ECP Address, enter the default code of
“4140” to advance to the next screen.
Note: Default code “4140” is the TUXEDOW default installer code before connecting to a control
panel. Once connected to a control panel, use that panel’s installer code.
1. Select Setup →System Setup → CS Setup .
2. Enter an Authorized Code, if required.
3. Select ECP Address ; enter an ECP Address. Available ECP Addresses are: 1-2, 5-
6…. for residential controls
1-2, 3-30... for commercial controls under Rev. 10; supports 3 AUIs. *See Important Note.
1-30 ……. for commercial controls Rev. 10 or higher; supports 6 AUIs.
*IMPORTANT NOTE: If multiple Touchscreens are being used, they must be set to addresses
1, 2, and X (where X equals any address from 3 through 30). Only one AUI type (Touchscreen)
device may be assigned to an address from 3 through 30 on commercial control panels.
4. Select the Homepage and Operation Mode from the Options menu.
DISARMING THE SYSTEM AND SILENCING ALARMS
To silence Alarms or Trouble conditions: enter your 4-digit user code, select the Clear
button, then enter your 4-digit user code again.
To test the Alarm, select the Security and More Choices icons.
- Select Console Mode and refer to the Control Panel User Guide for procedure.
DISPLAY & AUDIO SETUP
1. Select Setup ; slide the Brightness / Volume bar to adjust settings.
2. Select Setup → Disp & Audio Setup ; enter an Authorized Code.
- To adjust the screen timeouts, select a time interval from the drop-down list for each option
(Language, Backlight Off After, To Homepage After, and Auto Slideshow After.)
- Select Chime, Voice or Voice Chime operating mode.
- To clean the Touchscreen screen, select the Clean Screen icon; select Continue, or select
Cancel to exit.
- Select the Back arrow to return to the previous screen. Select to save changes.
USER SETUP
1. Select Setup → System Setup → User Setup .
2. Select and enter a User name and enter an Authorized Code for this user. Select each
field and enter the appropriate information.
3. Select to save the user information or select Back arrow to return to the previous screen.
For available user numbers, see control panel instructions.
TIME & DATE
1. Select Setup → System Setup → Time/Date Setup .
2. Enter an “Authorized Code”.
a) If Get Time is selected, the Touchscreen downloads the time/date from the control panel
and exits the “Set Time” screen. (The Get Time icon appears with residential panels and may
not appear with all commercial panels.)
b) Or, set the time/date from the Set Time/Date screen. Use the slide bar to scroll and select
each value.
3. Select to save: A message displays “Time Setting Confirmation”, select Yes or No.
SCREEN SECURITY
See the full Installation Guide for user Authority Levels.
1. Select Setup → System Setup → CS Setup .
2. Enter an Authorized Code; select the Screen Security icon.
- To make changes, select the line to change and the level of user to have access, and then
select to save changes.
CODE AUTHORITY
1. Select Setup → System Setup → CS Setup.
2. Select Code Authority .
3. Enter the 4-digit Code for the user you want to obtain authority level information about.
PANEL CONFIGURATION
1. Select Setup → System Setup → CS Setup.
2. Enter an Authorized Code and select Panel Config . Select to clear the
Touchscreen and reload the panel configuration into the Touchscreen.
OUTPUT SETUP
1. Select Setup →System Setup →Advanced Setup.
2. Enter an Authorized Code and select the Output Setup icon.
3. Select the outputs to display on the Output screen by selecting Enable or Disable and then
select Apply.
NIGHT SETUP
The NIGHT function can be set to arm the system in one of five arming modes. To change the
arming mode;
1. Select Setup →System Setup → Advanced Setup.
2. Enter an Authorized Code.
3. Select Night Setup; select desired mode:
Away - Stay - Instant (default) - Night (Residential Panel Only) – Maximum.
4. Select
to save changes.
EMERGENCY MESSAGES
1. Select the PANIC Icon. Press and hold (for at least 2 seconds) the associated alarm icon
(FIRE, POLICE or MEDICAL).
MULTIMEDIA
Picture Setup: Insert media card (Micro SD/SDHC) with stored (.bmp, jpg, png or .jpeg) photos.
1. Select the Multimedia and Picture icons and then select a Picture folder to view.
2. Select a photo and select Play to view pictures in a slide show format.
3. To set a picture as wallpaper, select the Default/Wallpaper folder to activate.
4. Select the Picture Info icon to view picture information.
Video Setup: Insert media card (Micro SD/SDHC) with stored video files. Supported video
playback formats are (avi, .ts, .mpg, .mp4, .mov, .mkv, or .flv).
1. Select the Multimedia and Video icons and then select the Video folder to view.
2. Select Play to start the selected video file.
3. Select the Video Info icon to view video information.
Camera Setup: See the full installation Guide for further information.
• If using existing (mounted) cameras; go to Step 4.
• For first time setup, scan/configure the cameras prior to mounting, and do the following:
1. Connect an Ethernet cable to the back of the camera (LAN); connect the opposite end to the
Ethernet Port on the router.
2. Apply power to the camera; wait for initial power-up.
3. Select Camera → Add
AddAdd
Add.
4. Select Scan
ScanScan
Scan to locate the camera. The screen displays:
“Scanning For Camera. Please Wait…”
5. Select the Add
Add Add
Add icon if the camera information is not automatically located, to enter information
manually.
6. To edit camera information, highlight the camera name and select the Edit
Edit Edit
Edit icon. Enter required
information and then select the Save icon.
a) To retrieve camera settings and connect to the camera, select the Connect
ConnectConnect
Connect icon.
b) Select TC Server Info icon to reset the camera for remote viewing and activate
a Total
Connect account.
c) Select Reset
ResetReset
Reset to reset the camera to factory default. Select Yes
YesYes
Yes or No
NoNo
No.
7. When all cameras have been added, select Wireless Settings and enter the wireless
information from the router.
8. Select Apply to All
Apply to AllApply to All
Apply to All to set cameras to wireless operation and control the Security System, local
Z-Wave devices and view local cameras from your browser. If the camera does not have
wireless capability, leave the camera connected to the router.
Use the icons to: Delete
DeleteDelete
Delete → Play
PlayPlay
Play → Stop
Stop Stop
Stop → Refresh
RefreshRefresh
Refresh → Auto Pan
Auto PanAuto Pan
Auto Pan → Full View
Full ViewFull View
Full View → Pan/Tilt
Pan/TiltPan/Tilt
Pan/Tilt → Back
BackBack
Back.
Wi-Fi SETUP
The TUXEDOW Keypads IP Address is used on a standard web browser to control user
functions such as Security, Z-Wave operation, and camera viewing. See Full Installation Guide
for supported browsers.
1. To connect to a Wi-Fi network, select Setup →System WIFI and select a Wi-Fi
network from the list to connect to. Or, select to add a new Network connection. Enter the
new Network name SSID No. and Security type; then select Connect.
2. Select the Setup and System Info icons; the IP Address is displayed on the System
Information Screen. Enter the IP Address on the keypad into a PC, Smart Phone or Tablet
Browser.
3. For Remote Access, select the Account icon to create a browser log-on page for
each user (for higher security) when viewing from a web enabled device or PC on a different
sub-net. Enter the required information for each field.
AUTOMATION - DEVICES
Add a Z-Wave Light, Switch, or Outlet Module: (if using two keypads, see Full installation
Guide section “Secondary Keypad” [Controller]).
1. Install device according to the manufacturer’s instructions.
2. Select Devices → Setup
Z
→ ADD DEVICE; enter required Z-Wave information.
3. Select the Function Key on the device; follow the keypad’s on-screen messages until
“Device added successfully”.
Add a Door Lock:
1. Assemble the Z-Wave door lock according to the manufacturer’s instructions.
Be sure the door lock orientation/handedness is correct.
2. Refer to Door Lock’s Instruction Guide and connect necessary cables, then install batteries.
3. Enroll the door lock within 5 feet of the keypad; refer to the Door Lock’s Instruction Guide for
procedure.
NOTE: Program a 4-digit user code in the control panel prior to programming that user code into
the door lock.
4. Select Devices → Setup
Z
ADD DEVICE; enter required Z-Wave information.
5. Program the selected user code from the panel.
Add a Honeywell Thermostat:
1. Install thermostat according to the manufactures instructions.
2. Select Devices → Thermostat ; enter the Account User Name, and Password.
Select the Thermostat button and enter DEV ID, Name and Location.
Enrollment procedure may vary. Refer to the Thermostat instructions.
3. On the Honeywell thermostat select Thermostat; set the “Time/Date” and follow the
instructions in the thermostat Installation Guide for enrollment.
4. To complete, select Done.
5. Select Exit to return to normal operation.
6. To verify activation: on the TUXEDOW Keypad, select Back; wait 30 seconds. Select
Refresh; the new device is displayed. See Installation Guide to Delete/Edit/Abort Z-Wave
devices.
SCENE SETUP
The Scene feature is used to control a single device, or multiple devices based on pre-set
“Conditions,” “Triggers,” and “Actions.” When a trigger/condition occurs, the defined action is
executed.
1. Select Devices → Scene → Add.
2. Select Users Scene; enter a SCENE NAME and select OK.
3. Add the “Condition,” “Trigger,” and “Action” that you want to occur for this Scene.
4. After each selection select Save !!
Note: Determine if you need a Condition. The Condition is a ‘condition’ set to occur prior to a
trigger event. See example below.
Example: Turn the lights on when the system disarms, but only at night.
(Condition) … “only at Night” ….Set the TIME Condition (enter the Start Time and Duration).
(Trigger) … when the “system Disarms” …Set the Trigger to SECURITY: System Disarm
(Action) …Turn the “lights ON” … Set the Action to LIGHT: ON.
Scene Rules
• Triggers & Conditions include: Time, Security, Thermostat, Door, Garage Door, Water Valve.
• Actions include: Security, Lights On/Off, Thermostat, Door, Garage Door and Water Valve.
• Each Trigger event can have up to 3 Actions.
• A Trigger event and Condition cannot be the same (i.e., if setting a Trigger event for
SECURITY, you cannot set a SECURITY Condition).
• On commercial panels the programming option for “Global Keypad” must be set to “0” for
some Scenes to work properly.