User's Guide

6290W Touchscreen Home Security System
Quick Installation Guide
Full Installation Guide [Part Number 800-24918] available online at: https://mywebtech.honeywellhome.com
POWER / RESET
BUTTON
6290W-008-V0
FLASHING – The system contains new
message(s) for the User.
OFF – No new messages.
ON – System is armed.
OFF – System is not armed.
ARMED (RED) LED
READY (GREEN) LED
ON – System is disarmed and ready to arm.
OFF – System is armed or disarmed but not
ready. If disarmed, faults or troubles are present.
MESSAGE (YELLOW) LED
Ready To Arm
PM
7:27
Setup
Security
Multimedia
Wednesday, February 1, 2012
P1 H
7:27 PM
To reset the Touchscreen, press and hold the side Power Button for 3 seconds and then touch the reset button on the screen to start the reset function. The Touchscreen
can also be reset by pressing and holding the reset button for approximately 15 seconds until the touchscreen resets automatically.
TOUCHSCREEN INITIALIZATION
When initially powered, the boot sequence and the "Set ECP Address" is displayed. If
using one Touchscreen, leave the address set to 1 and press Apply. If using more
than one, power-up each Touchscreen one at a time, and set each Touchscreen
address to one of the addresses enabled in the control panel.
Language Selection - If applicable, after initial ECP selection is set, the “Languages”
menu is displayed. Select a language.
SYSTEM INFORMATION / UPGRADES
To view the current software version installed, Interface name and MAC Address,
press Setup → System Information.
Software upgrades may be available. Log in to MyWebTech (see above) and enter
the model name in the “Search by” “My Product” field. Press Go; click on
Touchscreen software update SBS”.
ECP ADDRESS
If the screen is displaying “ECP Error”, the ECP address in the Touchscreen is not
valid for the panel that it is connected to. In this case, to change the ECP Address,
enter the default code of “4140” to advance to the next screen.
Note: Default code “4140” is the Touchscreen default installer code before connecting
to a control panel. Once connected to a control panel, use that panel’s installer code.
1. Press Setup →System Setup → CS Setup .
2. Enter an Authorized Code, if required.
3. Press ECP
ECP ECP
ECP Address&Options ; enter an ECP Address. The available ECP
Addresses are:
1-2, 5-6…. for residential controls
1-2, 3-30... for commercial controls under Rev. 10; supports 3 AUIs. *See
Important Note below.
1-30 ……. for commercial controls Rev. 10 or higher; supports 6 AUIs.
*IMPORTANT NOTE: If multiple Touchscreens are being used, they must be set to
addresses 1, 2, and X (where X equals any address from 3 through 30). Only one
AUI type (Touchscreen) device may be assigned to an address from 3 through 30 on
commercial control panels.
4. Select the Homepage and Operation Mode from the Options menu.
DISPLAY & AUDIO SETUP
1. From the Home screen press Setup , slide the Brightness /
/ /
/ Volume bar up
or down to change settings. Press Yes
YesYes
Yes to save.
2. Press Setup → Disp & Audio Setup ; enter an Authorized Code.
- To adjust the screen timeouts, select a time interval from the drop-down list for
each option (Language, Backlight Off After, To Homepage After, and Auto
Slideshow After.)
- Select Chime, Voice or Voice Chime operating mode.
- To clean the Touchscreen screen, press the Clean Screen icon; press Continue,
or press Cancel to exit.
- Press the Back arrow. Press to save changes.
USER SETUP
1. Press Setup → System Setup → USER .
2. Press + and enter Authorized Code; select each field and enter the appropriate
information.
3. Press to save.
For available user numbers, see control panel instructions.
TIME & DATE
1. Press Setup → System Setup→ Time/Date Setup .
2. Enter an “Authorized Code”.
a) If Get Time is pressed, the Touchscreen downloads the time/date from the
control panel and exits the “Set Time” screen. (The Get Time icon appears with
residential panels and may not appear with all commercial panels.)
b) Or, set the time/date from the Set Time/Date screen.
3. Press and.
MULTIMEDIA
Picture Setup: Press Multimedia → Picture.
1. Insert a media card (Micro SD/SDHC) with up to 1000 stored (.bmp, jpg, png or
.jpeg) photos.
2. Press the viewing transition arrow; select Standard, Horizontal, Vertical, and Fade
Out.
3. Press the Slide Delay arrow to select a time interval for viewing pictures.
- Use the icons to: Play Image → view Previous Image → go to Next Image →
Deselect Image or Add Image. Use the slide bar to select a wallpaper file from the
list and press Set Wallpaper.
(* While viewing photos in Full View, press anywhere on the screen to exit.)
Video Setup: Press Multimedia → Video.
Insert a media card (Micro SD/SDHC) with stored video files. Supported video
playback formats are (avi, .ts, .mpg, .mp4, .mov, .mkv, or .flv).
Maximum video resolution should not exceed 400 x 240.
- Highlight a video file from the list and press Play to start the selected video file.
- Press Repeat to continually replay selected video.
- Deselect the Repeat icon to play the list of video files starting with the first video
and ending with the last.
- Use the icons to: Pause → view a Full View.
(* While viewing videos in Full View, press anywhere on the screen to exit.)
SCREEN SECURITY
See the full Installation Guide for user Authority Levels.
1. Press Setup → System Setup → CS Setup .
2. Enter an Authorized Code; press Screen Security .
- To make changes, select the line to change and the level of user to have
access, and then press .
CODE AUTHORITY
1. Press Setup → System Setup → CS Setup.
2. Press Code Authority .
3. Enter the 4-digit Code for the user you want to obtain authority level information
about.
PANEL CONFIGURATION
1. Press Setup → System Setup → CS Setup.
2. Enter an Authorized Code and press Panel Config .
Touch to clear the Touchscreen and reload the panel configuration into the
Touchscreen.
NIGHT SETUP
The NIGHT function can be set to arm the system in one of five arming modes. To
change the arming mode;
1. Press Setup →System Setup → Advanced Setup.
2. Enter an Authorized Code.
3. Press Night Setup; select desired mode:
Away - Stay - Instant (default) - Night (Residential Panel Only) – Maximum.
4. Press to save changes.
EMERGENCY MESSAGES
1. Press the PANIC Icon.
2. Press and hold (for at least 2 seconds) the associated alarm icon (FIRE, POLICE
or MEDICAL).
Panel Faults – If
If If
If Panel Fault icons are
Panel Fault icons are Panel Fault icons are
Panel Fault icons are displayed on the Security screen
displayed on the Security screendisplayed on the Security screen
displayed on the Security screen, contact your alarm company
, contact your alarm company, contact your alarm company
, contact your alarm company. See the full Installation Guide.
. See the full Installation Guide.. See the full Installation Guide.
. See the full Installation Guide.
AC Loss
Bell Failure
Expander Failure
Low Battery
LRR Supervision Failure
1
Max Attempts
Exceeded
Pager Failure
1
Telco-1 Cut
2
Telco-2 Cut
Wireless Failure
Panic
Draft