USER MANUAL Version 1.
Copyright Copyright 2019 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety Regulatory Information Caution: Only use approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Power Supply Use only the approved power supply output rated 12 Vdc and minimum 3 A. The power supply is certified to EN60950-1 or EN62368-1 with SELV outputs.
Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.
The use of 2.4GHz WLAN's, for use through the EEA, have the following restrictions: Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 2.4 - 2.454 GHz. Italy requires a user license for outside usage.
Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to the reseller for recycling.
Revision History Version Date 1.
Table of Contents 1 2 3 Item Checklist ................................................. 9 1-1 Standard Items ..............................................................................9 1-2 Optional Items ..............................................................................9 System View ..................................................11 2-1 Front View ................................................................................... 11 2-2 2-3 Rear View ............................
1 Item Checklist 1-1 Standard Items a. System b. 36W power adapter c. Battery 1-2 Optional Items a. MSR b.
c. 10 Augusta d. Ingenico e. Mini Smart Card II f. Charging cradle g. Battery x 4 h.
2 2-1 System View Front View No.
2-2 12 Rear View No.
2-3 Specification System Motherboard CPU System memory Flash memory Quest VIII F12 Octa-core A53 series 3GB LPDDR3 32G eMMC LCD Touch Panel LCD size 8” IPS LCD Brightness 500 nits Resolution 1200 x 1920 Touch screen P-CAP 5 points Multi-touch Wireless Networking Wireless LAN Bluetooth NFC 4G/LTE 802.11 a/b/g/n/ac 4.0+LE, Class 2 13.56 MHz, compatible with ISO 15693, ISO 14443A, ISO 14443B (optional) 1x 4G LTE w/single antenna (optional) External I/O Ports USB 1x USB-C 3.0 (+ USB2.
System Motherboard Quest VIII F12 Accessories Hand strap 1 (must) Battery & Power Battery 1S2P, 3.85V, 28.
3 Getting Started 3-1 Power On/Off the System 1. Push the power button 1 second to turn on the system and hold 4 seconds to turn off the system. Note: For best touch performance, remove the protective plastic overlay from the LCD screen by peeling it away from one of the corners. Be sure to use a soft pointing device or finger tip to avoid scratching the screen during normal use. 3-2 Charging the Battery 1.
3-3 Replacing the Battery 1. Power off the tablet. Unplug the AC cable if connected directly to the DC-in port on the tablet. Place the tablet face down on a flat surface. Next, slide the latches up as shown to unlock and release the battery cover. 2. A plastic tab is attached to the battery module. For easier removal pull the plastic tab upwards to release the battery from the unit. 3.
3-4 Installing Peripheral Kits 1. Remove the screws (x4) to release the dummy cover first. 2. 3. Connect the cable to the connector on the system side. Insert the peripheral module in place and fasten the screws (x4) on the back to secure the module. Note: The variety of peripheral kits (MSR/ Augusta combo reader/ MSR & Smart card combo reader/ Ingenico RP457C/ VP3300) all follow the same installation method. 3-5 Using the Charging Cradle 1. To charge your M284 tablet, slide it into the cradle slot.
3-6 Using the Tablet Charger 1. 3-7 Attaching the Hand Strap 1. 2. 18 Insert the M284 tablet into the slot, then connect the AC adapter to the DC-in input and connect the other end to the power outlet. Align and attach the hand strap to the back side of the tablet and fasten the screws (x2) to secure it. The hand strap has a buckle in its center, to release the buckle, open the Velcro and simply push the two prongs on the sides and pull the buckle apart.
