REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE) Owner’s Manual Remote Controller Model name: Wireless Remote Controller Kit RBC-AX31U(W)-E RBC-AX31U(WS)-E Generic model name RBC-AX31U(W)-E RBC-AX31U(WS)-E Owner’s Manual Remote controller for air conditioner (Split type) Wireless remote controller and signal receiving part WH-H1JE2 (Wireless remote controller model name) 1 English Manuel du proprietaire Télécommande pour climatiseur Français (Type split) 15 Betriebsanleitung Fernbedienung für klima
Owner’s Manual Wireless Remote Controller Kit • Please read this Owner’s Manual carefully for correct use before using your Wireless Remote Controller Kit. Be sure to read “PRECAUTIONS FOR SAFETY” • After you read this manual, please keep it with the Owner’s Manual of the air conditioner in a place where you can access it quickly. Contents 1 PRECAUTIONS FOR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .
Owner’s Manual Wireless Remote Controller Kit 1 PRECAUTIONS FOR SAFETY WARNING WARNINGS ABOUT INSTALLATION • Make sure to ask the qualified installation professional in electric work to install the remote controller. If the remote controller is inappropriate installed by yourself, it may cause electric shock or fire, etc. • Make sure to install the air conditioner specified by TOSHIBAand ask the exclusive dealer when installing.
Owner’s Manual Wireless Remote Controller Kit 2 PART NAMES AND FUNCTIONS Remote Controller (WH-H1JE2) • Up to 8 indoor units in a group can be controlled by one remote controller. 7 1 11 12 2 Used after batteries are replaced or the slide switch is switched. (See page 10) 8 9 10 11 ADR 6 7 8 ACL SENSOR 15 16 17 18 12 1 2 Transmitting part Start/Stop button Starts and stops the air conditioner alternately.
Owner’s Manual Wireless Remote Controller Kit Signal Receiving Part • The signal receiving part is attached to the indoor unit. • Hereinafter, all remote controller button names are indicated with respective symbols displayed on the remote controller. Example: Start/Stop button → 4 5 6 1 The rear of signal receiving part The following switches are provided on the rear of the signal receiving part. For their settings, contact the dealer from whom you purchased the air conditioner.
Owner’s Manual Wireless Remote Controller Kit Display section All inticators are shown in the right and the lower figures for the explanation. Only selected contents are display in actual operation. • When turning on the leak breaker at the first time, [SET DATA] flashes on the display part of the remote controller. While this display is flashing, the model is being automatically confirmed. Accordingly, wait for a while after [SET DATA] display has disappeared, and then use the remote controller.
Owner’s Manual Wireless Remote Controller Kit Operation section Push each button to select a desired operation. • The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing ON/OFF only. 5 1 2 3 6 ADR 4 1 SENSOR ACL Operation select button 6 Selects the desired operation mode. 2 Fan mode select button Time setup button Used for timer setting. (See page 8) 4 Check button The CHECK button is used for the check operation.
Owner’s Manual Wireless Remote Controller Kit 3 HOW TO OPERATE INDOOR UNIT 5 Auto, Heat, Dry, Cool, Fan Push . When the operation is stopped with the remote controller, the outdoor unit fan keeps running in some cases even after the compressor of the outdoor unit has stopped. • The automatic cooling/heating and heating functions are not provided for cool-only types.
Owner’s Manual Wireless Remote Controller Kit 4 HOW TO OPERATE THE TIMER • After the timer has been set, put the remote controller at a position where signals of the remote controller can reach the signal receiver on the indoor unit. The timer operation signal is transmitted from the remote controller.
Owner’s Manual Wireless Remote Controller Kit 5 HOW TO ADJUST AIR DIRECTION • While the air conditioner is not working, the louver (air direction adjusting plate) is closed automatically. • During the preparation for heating, the louver is directed upward and it starts swinging after the preparation for heating is canceled though the automatic louver display on the remote controller shows swinging even during this period. To set air direction To stop swinging Push during operation.
Owner’s Manual Wireless Remote Controller Kit 6 SLIDE SWITCH • The settings of operation mode display and air direction display vary as follows depending on the indoor unit in use. • Use a fine-tipped tool to change the switch setting. • Push the RESET button after the switch setting is changed. 1 Louver display switch View with the cover removed SENSOR ACL Louver display of the remote controller 1 2 Slide switch position * Set the slide switch to “S.
Owner’s Manual Wireless Remote Controller Kit 8 HOW TO HANDLE THE REMOTE CONTROLLER • Point the transmitting part of the remote controller at the signal receiving part of the indoor unit. When a signal is received normally, “pi” sound is heard once. (“Pi, pi” is heard only at the beginning of operation.) • The standard signal receivable distance from the signal receiving part of the indoor unit is approx. 7 m. The distance varies somewhat with the battery capacity or other conditions.
Owner’s Manual Wireless Remote Controller Kit 10 ADDRESS When two or more indoor units controlled by the same wireless remote controller are installed in a room, a unique address can be set for each indoor unit to prevent interference. Up to 6 indoor units can be controlled independently by the remote controller by matching the address switch setting of the signal receiving part with the address displayed on the remote controller.
Owner’s Manual Wireless Remote Controller Kit 11 HOW TO PERFORM EMERGENCY OPERATION In the event of an emergency shown below, push emergency operationeon the signal receiving part (inside the ceiling panel or indoor unit) for emergency operation. • The batteries of the remote controller have been exhausted. • The remote controller is out of order. • The remote controller has been lost. 1 2 1 Start Push emergency operation.
Owner’s Manual Wireless Remote Controller Kit 12 BEFORE ASKING FOR REPAIR WORK Check the following before asking for repair work. Check again Phenomenon Possible cause Measures Operation does not start even if the switch is turned on. The air conditioner is not working or a power failure has occurred. Push on the remote controller again. (See page 7) The power switch is not turned on. Turn on the power switch if it is off. (See page 7) The air conditioner is in the ON timer operation.
