SQPB Video Cassette Recorder W-727 OWNER’S MANUAL 3 ABLE BOX ONTROL W-727/Eng (1-9) 1 3/6/02, 1:37 PM
SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
IMPORTANT PRECAUTIONS Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will mar the finish. INTRODUCTION Save Original Packing Materials The original shipping carton and packing materials will come in handy if you ever have to ship your VCR. For maximum protection, repack the set as it was originally packed at the factory.
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing.
6. Water and Moisture Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like. 8. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. INTRODUCTION 7.
IMPORTANT SAFETY INSTRUCTIONS 12. Lightning For added protection for this product during storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 13.
Contents Provides important notes and general explanation of the VCR, including names of the buttons, jacks, etc. SAFETY PRECAUTIONS .................... 2 IMPORTANT PRECAUTIONS ............. 3 IMPORTANT SAFETY INSTRUCTIONS ................................... 4 Contents .............................................. 7 Identification of Controls ................... 8 • Front Panel • Remote Control • VCR Display • Rear Panel Variable Speed Playback .................
INTRODUCTION Identification of Controls See the page in for details. This manual shows the names of buttons in italics. Front Panel POWER EJECT 14 18 CHANNEL Cassette compartment STOP 19 19 18 24 PLAY 19 19 20 SHUTTLE REC LINE IN 2 VIDEO jack 24 20 Remote Sensor 10 9 PAUSE/STILL VCR Display LINE IN 2 AUDIO (L/MONO, R) jacks Remote Control To operate this TV. TV 40 14 POWER To operate your VCR. VCR 14 POWER VCR TV 1 2 3 4 5 6 19 CH/TRK Number buttons 17 I.
VCR Display Cassette indicator Hi-Fi indicator Timer recording indicator TIMER Hi-Fi SAP VCR VCR indicator Multifunctional indicator SAP indicator Rear Panel LINE OUT AUDIO jacks (L, R) RF IN (FROM ANT.) terminal LINE IN 1 AUDIO jacks (L, R) LINE OUT LINE IN 1 IN (FROM ANT.
PREPARATION How to Use the Remote Control This section explains how to get ready for remote control operation. Setting up the Remote Control 1 Open the battery compartment lid on the rear panel. 2 Install 2 batteries (“AAA” size) following the polarity diagrams. 3 Close the battery compartment lid. 4 Point the remote control at the VCR and press the buttons within the operating range.
PREPARATION Connections Before you use this VCR, it is necessary to connect it to your TV. Several ways of connecting are available depending on your use of TV or cable box. Select one which is applicable to your equipment. Antenna/VCR/TV Connection Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the VCR. 2 Connect the RF OUT terminal to the TV. VHF/UHF combination antenna VHF antenna only IN LINE OUT LINE IN 1 IN (FROM ANT.) (FROM ANT.
Connections (continued) This set-up will enable you to: LINE OUT LINE IN 1 – record an unscrambled channel. – watch an unscrambled channel while recording it. – record an unscrambled channel while watching another (scrambled or unscrambled). IN (FROM ANT.) R AUDIO L OUT RF (TO TV) VIDEO CH 3 4 Cable box You will need to: Incoming cable OUT IN • set TV channel to the output channel of the cable box.
PREPARATION Auto Set Up The VCR’s clock and tuner channels are set automatically when the VCR is plugged into the AC outlet. Auto Set up TV 1 2 CH/TRK 3 4 5 6 7 8 9 0 100 the data broadcast by the local TV stations. While “Auto” is blinking, channel memory is also set automatically. TV VOL I.
PREPARATION Initial Settings Using On-screen Display The language selection and clock setting must be set first when VCR is first plugged in or after it encounters a power failure. Preparation • Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video connection (page 11). • Press VCR to set the remote control operating the VCR. Setting the Language VCR POWER VCR TV 1 2 POWER CH/TRK 3 4 5 6 7 8 9 0 100 TV VOL 1 2 Press PROG..
8 Setting the Clock Example: To set the clock to 2:30 p.m. on August 25 (summer time) 2002. 1 Press PROG.. Select “PRESET” using FF or REW, and press ENTER. 1 SCA 9 3 Press ENTER to select “CLOCK SET”. PRESS En TER TO START SETTIn G Select “AUTO” or “MANU” using PLAY/x2 or STOP. AUTO: The VCR automatically sets or adjusts the clock. If you select “AUTO” mode, proceed to step 8. MANU: You can set the clock manually. If you select “MANU” mode, proceed to next step.
PREPARATION Storing Channels on the VCR This section is required if you receive only normal TV or unscrambled cable channels, or use a cable box between your TV and the VCR. Incoming Antenna/Cable(CATV) Signals The VCR scans through all receivable TV and CATV channels and stores only the active ones in your area into the memory. Once the storing is finished, you can select a desired channel using CH/TRK.
Adding or erasing channels 3) Enter a channel number of 1 to 125 using number buttons. For more than 100 number, first press 100. For CATV channels, refer to the chart below. (For other orders, check with your cable company.) 4) Repeat steps 2) and 3) to add or erase channels as necessary. 5) Press PROG. twice to exit. 1) Follow steps 1 to 3 of “Incoming Antenna/ CATV Signals”. 2) Select “ADD CH” or “ERASE CH” using PLAY/x2 or STOP.
PREPARATION Video Cassette Use Video Cassette Use Loading a cassette Push the cassette into the cassette compartment with the window side facing up and the label side towards the front. The VCR is automatically turned on. The indicator will appear in the VCR display. Ejecting a cassette Press EJECT. The cassette is ejected from the cassette compartment. Warning Do not insert your hands or any foreign objects into the compartment. This may result in injury or damage.
PLAYBACK Playback This section explains the basic playback operation. Preparation • Select the video channel (3 or 4) or video input mode on the TV. • Press VCR to set the remote control operating the VCR. Basic Playback 1 POWER VCR TV 2 1 3 5 6 8 9 0 100 TV VOL I.SELECT DISPLAY 2 REMAIN/ COUNTER COUNT RESET TV/ VCR PLAY/x2 SLOW VCR S Press PLAY/x2 to start playback. REC L TIMER TIMER REC SP/ SLP TIMER S L P PLAYBACK CH/TRK 4 7 Load a recorded cassette.
PLAYBACK Variable Speed Playback You can play back a tape at various tape speeds. Picture Search A tape runs at 5 times or 7 times the normal playback speed so that you can quickly locate a particular scene. POWER VCR TV 1 2 3 4 5 6 7 8 9 0 100 CH/TRK 1 TV VOL DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR TIMER REC SP/ SLP PLAY/x2 SLOW CURSOR FF STOP CANCEL VCR Plus+ A.SELECT EJECT PLAY/x2 2 PAUSE/STILL REW PROG. Press FF or REW during playback.
Adjusting Still Picture Stability If the still picture is distorted or flickers, hold down one of CH/TRK until the picture becomes stable. Note: The distortion of the still picture may not be eliminated completely. POWER TV 1 2 3 4 5 6 7 8 9 0 100 Frame Advance CH/TRK A picture advances frame by frame. TV VOL I.SELECT DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR TIMER REC SP/ SLP PLAY/x2 SLOW PAUSE/STILL CURSOR REW SLOW PLAY/x2 PAUSE/STILL FF CANCEL VCR Plus+ A.
PLAYBACK Useful Functions in Tape Operation These functions will help your playback. Counter Function You can view the clock, linear time counter or tape remaining time in the VCR display or on the TV screen. POWER VCR TV 1 2 3 4 5 6 7 8 9 0 100 CH/TRK REMAIN/ COUNTER TV VOL COUNT RESET Each time you press REMAIN/COUNTER, the VCR display changes in sequence as follows: → Linear time counter → Tape remaining time (R) → Clock I.
Memory Stop Feature (Zero Return) POWER VCR TV 1 2 CH/TRK REMAIN/ COUNTER TV VOL COUNT RESET 3 4 5 6 7 8 9 0 100 1 On the SET UP screen, select “COUNTER MEM.” using PLAY/x2 or STOP, and set to “ON” using REW or FF. 2 Press PROG. once to exit. I.SELECT DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR REC SP/ SLP TIMER PAUSE/STILL DISPLAY PLAY/x2, STOP CURSOR REW FF FF STOP PROG. CANCEL VCR Plus+ A.SELECT EJECT ENTER CABLE BOX CH CM SKIP REW ENTER POWER PROG.
RECORDING Recording a TV Program This section explains the basic recording operation. Preparation • Select the video channel (3 or 4) or video input mode on the TV. • If you record cable channels via the cable box, finish the cable box set-up (pages 32-35), and turn on the cable box . Basic Recording POWER VCR TV CH/TRK 1 2 3 4 5 6 TV VOL 7 3 1 2 Load a cassette with the safety tab attached. Press TV/VCR so that the “VCR” indicator appears in the VCR display. VCR 8 9 0 100 I.
RECORDING Timer Program Recording The programmable timer allows you to record up to 6 different programs over one month. Preparation • Select the video channel (3 or 4) or video input mode on the TV. • Make sure that the clock is set correctly (page 15). • Store the channels on the VCR (pages 16 and 17). • If you record cable channels, finish the cable box set-up (pages 32-35), and turn on the cable box .
Timer Program Recording (continued) 5 Move to the next using FF, and set the recording date using PLAY/x2 or STOP. The date changes as follows: → 8/25 → 9/25 → … → 7/25 → WKLYSU → … MO~FR ← WKLYSA ← [WKLYSU]…[WKLYSA]: You can record TV programs on the same channel on the day and time every week. [MO~FR]: You can record TV programs on the same channel on the day and time Monday through Friday. 6 Move to the next using FF, and set the hour and minutes of the recording start time.
Confirming the timer programs If a power failure occurs during the timer program recording (including VCR Plus+ C 3 ® system recording (page 30) Press PROG. during timer recording mode. The screen for confirming will appear. P M P M • When a power failure has occurred, the programmed contents are not effected, reset the clock Overlaps of the programs Press PROG. again to exit from confirmation page.
RECORDING VCR Plus+ C3 ® system Set-up VCR Plus+ C 3 ® system is a timer recording system for an easier programming that requires you only to enter a PlusCode® programming number assigned to a desired program. This section explains the necessary set-up to make VCR Plus+ C 3 ® system recordings. The flow chart below will give you an idea as to what must be done to use the VCR Plus+ C 3 ® system feature.
Preparation • Select the video channel (3 or 4) or video input mode on the TV. • If you record cable channels, finish the cable box set-up (pages 32 – 35). • Prepare the list like below. Example Station Guide channel number (on the TV Guide, local TV listings etc.) HBO ESPN AMC 33 34 35 Your home channel number (on the channel line-up chart supplied by cable companies) 7 VCR TV 1 2 3 4 5 6 CH/TRK TV VOL 7 8 9 0 100 7 I.SELECT DISPLAY Press PROG..
RECORDING VCR Plus+ C 3 ® system Recording After performing the VCR Plus+ C 3 ® system set-up, you can easily program a recording simply by entering the PlusCode® programming numbers. The numbers are published in the TV listings of newspapers, TV guide magazine, etc. Preparation • Make sure that the clock is set correctly (page 15). • Load a cassette with a safety tab. For cable box users: • Finish the cable box set-up (pages 32 – 35), and turn on the cable box.
5 Press ENTER. The program setting is now memorized. • If your cable box is not remotecontrollable, select the recording channel on the cable box beforehand. 6 7 8 SP To set another program, repeat steps 1 to 5. Press PROG. now programming is completed. REC TIMER TIMERHi-Fi STERE L SAP Confirming the VCR Plus+ C3 ® system timer programs Recording or playback in the timer standby mode Before the VCR enters the timer standby mode (TIMER indicator not lit) 1)Press PROG. to display the MENU screen.
RECORDING Cable Box Set-up The VCR can directly control channel selecting of the connected cable box. Cable Box Control Connection Type This VCR needs to be connected to a cable box equipped with an infrared wireless remote control. You can select cable channels from the cable box by operating this VCR. It is also possible to automatically change the cable channels according to your program setting in the timer program recording or VCR Plus+ C 3®system recording.
Preparation • Select the video channel (3 or 4) or video input mode on the TV. • Set “TV/CATV” on the CH MEMORY screen to “CATV” (page 16). Cable Box Set-up POWER VCR TV 1 2 CH/TRK 3 4 5 6 7 8 9 0 100 TV VOL Number buttons I.SELECT DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR PLAY/x2 PAUSE/STILL CURSOR REW FF Press PROG. to display the MENU screen. 4 Select “NO” or “C.BOX” using FF or REW according to your connection type. 100 I.SELECT REW FF CANCEL VCR Plus+ A.
Cable Box Set-up (continued) 7 Select “BRAND TYPE” using STOP, and enter a brand code of your cable box using number buttons. Refer to the table on the next page. Example: For a TOSHIBA cable box, identified by number 36. Cable box display VCR display EnD : PROG Cable channel number Make sure that the channel display of your cable box has changed to 36. If not, try each brand code assigned to the brand of your cable box until the display changes to 36.
Table of cable box brand codes Brand name of your cable box Toshiba Anvision Archer Cablestar Cableview Citizen Curtis Diamond Eastern GC Brand Gemini General Instrument Hamlin Hitachi Jerrold Macom Magnavox Movietime NSC OAK OAK Sigma Panasonic Philips Pioneer Pulsar Randtek RCA Realistic Regal Regency Rembrandt Samsung Scientific Atlanta Sheritech SL Mark Sprucher Stargate Sylvania Teknika Telecaption 36 13, 20, 21, 22, 23, 24, 25, 26, 58, 62, 84 1, 20, 21, 29, 42, 44, 63, 88, 91 13, 20, 21, 22, 23, 24
RECORDING DSS® Satellite Receiver Set-up The VCR can directly control channel selecting of the connected DSS® satellite receiver. DSS® Satellite Receiver Control This VCR needs to be connected to a DSS® satellite receiver equipped with an infrared wireless remote control. You can select satellite channels from the DSS® satellite receiver by operating this VCR. DSS® is registered trademark of DIRECTV, Inc., a unit of GM Hughes Electronics.
Preparation Select the video channel (3 or 4) or video input mode on the TV. DSS® Satellite Receiver Set-up POWER VCR TV 1 2 1 2 Press PROG. to display the MENU screen. 3 Select “CABLE BOX/DSS” using PLAY/x2 or STOP, and press ENTER. CH/TRK 3 4 5 6 7 8 9 0 100 TV VOL Select “PRESET” using FF or REW, and press ENTER. Number buttons I.SELECT DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR PLAY/x2 PAUSE/STILL FF STOP PROG. CANCEL A.
DSS® Satellite Receiver Set-up (continued) OFF: if your DSS® satellite receiver is NON remote-controllable. • Satellite channels will be selected by the own channel selector of the DSS® satellite receiver. The VCR channel should be set to the output channel of the DSS® satellite receiver. → Go to step 8. 7 Select “BRAND TYPE” using STOP, and enter a brand code of your DSS® satellite receiver using number buttons. Refer to the table on the next page.
RECORDING MTS Broadcast Compatibility This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to your stereo system or stereo TV, you will experience the SAP or stereo sound. Preparation Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR. Recording the SAP/Stereo Broadcast POWER VCR TV CH/TRK 1 2 4 5 6 7 8 9 0 100 3 TV VOL On the SET UP screen (page 14), select “SAP SET” using PLAY/x2 or STOP, and set to “ON” using REW or FF.
ADDITIONAL INFORMATION Multi Brand Remote Control The remote control can be compatible with various brands of TV by setting their control codes. The TOSHIBA code has initially been set to control TOSHIBA TVs. Setting Control Codes POWER VCR TV 1 POWER CH/TRK 1 2 3 4 5 6 7 8 9 0 100 CH/TRK 1 Press TV to set the remote control operating your TV. 2 While holding down PROG. enter the two digits of your TV’s brand code (listed on page 41 ) using number buttons. TV VOL I.
Table of Brand Codes Brand name of your TV Brand Code Brand name of your TV Brand Code 01 Proton Bell & Howell 09 Pulser 14 Carver 10 Quasar 07, 15 Celebrity 03 Radio Shack 13 Citizen 12 RCA 02 Curtis Mathes 09, 12 Realistic 09, 11, 13 Dumont 14 Runco (NEC) 14 Electro band 03 Samsung 11, 12 Emerson 09, 11 Sanyo 09 Fisher 09 Scotch 11 GE 02, 07, 11 Scott 11 Gibralter 14 Sears 01, 02, 09, 10, 11 Goldstar 11 Sharp 08, 13 Hallmark 11 Sony 03 Hitachi 06
ADDITIONAL INFORMATION Before Calling Service Personnel Check the following symptoms before requesting servicing. No power. • The power cord is not plugged in. – Plug the power cord into the outlet firmly. Although the power is on, the VCR will not work. • There is no cassette. – Load a cassette. (page 18) The desired sound is not heard, such as SAP, stereo, or regular sound. • Setting of sounds is not correct. – Select a desired sound using A.SELECT.
The remote control does not work properly. • The batteries are exhausted. – Replace all batteries. (page 10) • The remote control is operated beyond the operating range. – Make sure the remote control is within 30° of the remote sensor on the VCR. (page 10) • Too far from the VCR. – Use the remote control within 7 m from the front of the VCR. (page 10) • An obstacle may be in the way of the operation. – Remove the obstacle. • The operating mode of the remote control is not set correctly.
Specifications Power Supply: Power consumption: External dimensions: Mass: Channels received: Antenna input/output terminals: Signal system: Recording/Playback system: Cassette: Tape speed: Video recording/playback time: Fast forward/rewind time: Video input: Video output: Audio input: Audio output: Audio frequency range (Hi-Fi): Audio dynamic range (Hi-Fi): Utilization conditions: 120 V AC, 60 Hz 18 W 430 x 94 x 252mm (W.H.D.) 3.
LIMITED WARRANTY TOSHIBA VIDEO CASSETTE RECORDER Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc. (“THI”) make the following limited warranties. These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee.
LIMITED WARRANTY (continued) How to Obtain Warranty Service (1)Refer to the troubleshooting guide in your owner's manual. This check list may solve your problem. (2)Call the TACP toll free number 800-631-3811 within (30) days after you find a defective product or part. (3)Arrange for the delivery of the product to the Authorized TACP/THI Service Station.