TEC Electronic Cash Register MA-1350-1 SERIES Owner’s Manual Operators Guide T.O.C. Manager's Guide T.O.C.
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
EO1-11131 Safety Summary Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
EO1-11131 Safety Summary Disconnect the plug. Connect a grounding wire. If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Disconnect the plug. Ensure that the equipment is properly grounded. Extension cables should also be grounded.
EO1-11126 MA-1350-1 SERIES OPERATOR’S GUIDE Operators Guide T.O.C.
TOC 2 EO1-11126 MA-1350-1 SERIES TABLE OF CONTENTS Page 1. Introduction .......................................................................................................... 1 2. Unpacking ............................................................................................................. 1 3. Outline of Preparation Procedure Before Operating the ECR ......................... 2 4. Appearance and Nomenclature .......................................................................... 3 5.
TOC 1 EO1-11126 MA-1350-1 SERIES Listing Capacity Open ....................................................................................................... 29 Percent Discount, Percent Charge .................................................................................... 30 Dollar Discount .................................................................................................................. 30 Vendor Coupon ...............................................................................
EO1-11126 MA-1350-1 SERIES 1. Introduction Thank you for choosing the TEC electronic cash register MA-1350-1 series. This owner’s manual provides a description of the functions and handling of this register and should be read carefully to ensure optimum performance. Since every consideration has been given to safety and reliability, there is no danger of damaging the machine by incorrect operation. Please refer to this manual whenever you have any questions concerning the machine.
EO1-11126 MA-1350-1 SERIES 3. Outline of Preparation Procedure Before Operating the ECR This chapter shows the outline of set-up procedure of the ECR before actually starting the ECR operation. 1 2 3 (1) (2) (3) (5) (6) (7) (8) Remove the tapes and seals for holding parts or protecting the register surfaces. Plug the power cord of the register into a wall outlet. Make sure that the outlet voltage matches that of the power required for the register.
EO1-11126 MA-1350-1 SERIES 4. Appearance and Nomenclature Printer Cover Customer’s Display Journal Window Receipt Outlet Operator’s Display Validation Slot Control Lock Drawer PC Interface Keyboard Operator’s Display Used by the operator to confirm the entry contents and the status of the register. (page 5) Customer’s Display Provided for the customer to see the amount entered for each item and sale total. (page 5) Receipt Outlet The receipt for the finalized sale is issued.
EO1-11126 MA-1350-1 SERIES 5. Control Lock and Control Keys Control Keys There are four types of Control keys: the REG key, the MGR key, the MA key, and the S key. The REG key is used by the cashier or clerk who operates ordinary transaction entries. This key can access the positions of OFF and REG of the Control Lock. REG REG Key: The MGR key is used by the store manager. This key can access the positions of OFF, REG, X, and MGR.
EO1-11126 MA-1350-1 SERIES 6. Display The Operator’s Display (front display) is located at the top of the register just above the keyboard. The Customer’s Display may be used only as a rear display if left in the retracted position or it can be positioned for viewing at other angles by pulling it upward and turning it to the desired position. The display has two types of display portions—numeric display and message descriptors (status lamps).
EO1-11126 MA-1350-1 SERIES Message Descriptors (Status Lamps) PC: Illuminates during data communication between the cash register and a personal computer. SLIP: Illuminates when a validation slip is properly inserted to allow the validation print. It flickers to inform that the validation print is required when the validation compulsory status has been programmed on the last operation. R OFF: Illuminates when the Receipt-OFF mode is declared by the [LOG/RECEIPT] key.
EO1-11126 MA-1350-1 SERIES 7. Keyboard The following is the standard keyboard layout, which was initially set at the factory. This register is designed to be capable of programming most of the keys at desired locations or adding keys, ask your TOSHIBA TEC representative. (For details about operations, refer to Chapter 13. Transaction Entries on page 21.
EO1-11126 MA-1350-1 SERIES Flat Keyboard Layout PLU Preset-code Keys 1 8 2 9 3 10 4 11 5 12 6 13 LOG RECEIPT VOID ITEM CORR ALL VOID RF JF RECEIPT ISSUE TX/M EX RTN MDSE R/A PO @/FOR chg NS c %- # 7 8 9 $5.00 AMT 4 5 6 $10.00 1 2 3 ST 0 00 .
EO1-11126 MA-1350-1 SERIES Functions of Each Key KEY FUNCTION Log/Receipt Key: Used for the cashier sign on/off operation when cashier signing option is selected after entering numbers. Also, used to select receipt issue or non-issue without entering numbers. LOG RECEIPT REFERENCE PAGE 17, 21 RF Receipt Feed Key: Used to advance the receipt roll and operated by holding it down until the paper is advanced to the required position.
EO1-11126 MA-1350-1 SERIES KEY FUNCTION Paid Out Key: Used to register paid out amount. PO PLU (Price-Look-Up) Key: Used to enter a PLU item that is linked to a department. PLU Amount Key: Used to enter a manual amount of PLU item. AMT ITEM CORR 7 4 8 5 9 6 1 2 3 0 00 . REFERENCE PAGE 23 26, 27 26, 27 Item Correct Key: Used to delete the last item entered within the current sale. 32, 33 Numeric Keys: Used to enter numeric data, such as amount, quantities, and code numbers.
EO1-11126 MA-1350-1 SERIES KEY FUNCTION Non-add Number Print / No-sale Key: It functions as the [#] (or [#/CID]) key and the [NS] key. #/NS Preset Price & Listing Capacity Open Key: It functions as the [PR OPEN] key and the [LC OPEN] key. OPEN CLERK 1 Cashier 1 to 8 Keys: Used to identify each cashier who to CLERK 8 operates the register. , $5.00 $10.00 CASH3 Cash Payment 1 to 3 Keys: Used for cash-tendering operation with the respective preset amounts. As initial setting, the amount $5.
EO1-11126 MA-1350-1 SERIES 8. Installing the Receipt/Journal Roll Installing the Receipt Roll WARNING! Care must be taken not to injure yourself with the paper cutter. X REG OFF MGR 1 Turn the Control Lock to the REG position using a Control Key. Z SET 2 To remove the Printer Cover, insert the Printer Cover Key to the Printer Cover Lock, and then turn it 90° clockwise. 3 Cut the paper end to make it sharp. 4 Place the paper roll in the outer side holder of the two roll holders.
EO1-11126 MA-1350-1 SERIES 5 Insert the paper end into the receipt inlet behind the printer. Then, feed the paper by hand into the inside of the printer while pressing the [RF] key provided at the central upper side of the keyboard until about 4 inches (about 10 cm) of paper comes out of the printer. VALI DATE TX M 6 Cut the excess paper with the attached cutter, and attach the Printer Cover. After closing the Printer Cover, depress the [#/NS] key to check print condition.
EO1-11126 MA-1350-1 SERIES Installing the Journal Roll 1 Follow Steps 1 to 5 for “Installing the Receipt Roll” on the preceding pages, except that the paper roll should be placed inner side of the two holders and the [JF] key should be used for the journal roll to advance about 8 inches (about 20 cm) of paper out of the printer. 2 Insert the paper end into the slit on the Take-up Reel and wind it around the reel two or three times. 3 Set the Journal Take-up Reel into the Reel Holder.
EO1-11126 MA-1350-1 SERIES 9. Installing the Ribbon Cassette X REG OFF MGR 1 - Turn the Control Lock to the OFF position. Z SET 2 To remove the Printer Cover, insert the Printer Cover Key to the Printer Cover Lock, and turn it 90° clockwise. 3 Install the Ribbon Cassette as shown in the figure. After installing the Ribbon Cassette, turn the knob of the Ribbon Cassette in the direction of the arrow mark several times to remove the slack on the ribbon. 4 Attach the Printer Cover.
EO1-11126 MA-1350-1 SERIES 10. Daily Operation Flow The following shows a typical daily operation flow on the register. Before Opening the Store ... Reference Chapter • Ensure that the register is firmly plugged in the wall outlet. 3 (O/G) • Check if enough portion of paper roll is left. 8 (O/G) • Check the time, date, and print condition. Check the time, date, and print by issuing a No-sale Receipt. ... Setting the time or date ... 13 (O/G) 4 (M/G) During Business Hours ...
EO1-11126 MA-1350-1 SERIES 11. Cashier Identifying Operation The register requires the cashier identifying operation for starting sales entries in initial status. However, the program option allows you to operate the register without the cashier identifying operation. For details, ask your TOSHIBA TEC representative. The MA-1350-1 adopts one of the following cashier-identifying methods.
EO1-11126 MA-1350-1 SERIES Name of a cashier who has just signed ON is printed if the name has been programmed. If not, a cashier symbol such as “3CL” is printed here.
EO1-11126 MA-1350-1 SERIES NOTES: 1. No receipts are issued on turning ON or OFF a Cashier Key. However, the Cashier Code (1 to 4) is printed near the bottom of every receipt to be issued. 2. The multi-drawer feature can be adopted on this cashier-identifying method. In this case, Drawer 1 is assigned to cashiers 1 and 2, and Drawer 2 to cashiers 3 and 4. 4) Cashier Key Method ([CLK] Key) A maximum of 8 cashier keys ([CLK 1] to [CLK 8]) can be installed on the keyboard.
EO1-11126 MA-1350-1 SERIES Entries in Training Mode When the cashier identifying option is selected, a sign ON or cashier Key ON is required before starting operations. Refer to Chapter 11. Cashier Identifying Operation on page 17. A trainee can operate all transaction entries described in the next chapter. except: 1) The drawer will not open. 2) The consecutive No. will not be incremented. 3) Entried contents will not be printed on a validation slip.
EO1-11126 MA-1350-1 SERIES 13. Transaction Entries This chapter describes individual key operations on transaction entries. • Turn the Control Lock to the REG position using the REG key. • In the operation patterns, of a transaction key. indicates an input through a numeric key, and indicates a depression WARNING! When opening the cash drawer, be careful not to let the drawer hit any person.
EO1-11126 MA-1350-1 SERIES Clearing Errors, or Clearing Wrong Declaration Key or Wrong Numeric Entries When in sale entries an error has occurred with an alarm buzzer, a wrong declaration key has been depressed and/or a wrong numeric data has been entered; Depress the C key to cancel the error condition or the entered data. For details for clearing the error, refer to Chapter 16. Troubleshooting on page 53.
EO1-11126 MA-1350-1 SERIES NOTE: As initial setting, all the media keys shown on the preceding page except the [chg] key can be used in the Received-onAccount transaction. TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 Paid Out Repeat if multiple amounts are paid out. PO R/A R/A CASH 10.00 2.50 12.
EO1-11126 MA-1350-1 SERIES NOTE: Entry of a negative department can be programmed to require the MGR position of the Control Lock. If so programmed, an error will occur on entering the negative department in the REG position. In this case, ask the store manager to turn the Control Lock to the MGR position for the entry. (Refer to the chapter 1. Operations in “MGR” Mode on page 1 in Manager’s Guide.). 2) Repeat Entry Open-price Department ... MEAT MEAT Dept. 7.00 TF 7.00 TF Dept.
EO1-11126 MA-1350-1 SERIES 4) Department SPP (Split-Package-Pricing) This operation is used when a customer purchases only part but not all of the items in a package (example: only two tomatoes in a priced package of three tomatoes.) Open-price Department ... Dept. Whole Package Price @/FOR @/FOR Purchased Qty Whole Package Qty Preset-price Department Dept. The preset price is regarded as the Whole Package price Purchased Qty 3X MEAT Department Name NOTES: 7.00/ 2 10.
EO1-11126 MA-1350-1 SERIES PLU Entries Entered Price (or preset price) 1) Entry of One Item: Preset-price PLU PLU Name Pork 2.00 TF PLU PLU Code; Max. 4 digits 1 to 9999 Status Symbol For the United States T: Taxable F: Food Stampable TF: Taxable and Food Stampable Blank: Not applicable to any of the above status For Canada F: GST Taxable P: PST Taxable FP: GST and PST Taxable Blank: Not applicable to any of the above status PLU PresetCode Key Open-price PLU PLU ... AMT Unit Price; Max.
EO1-11126 MA-1350-1 SERIES 3) Quantity Extension (Multiplication) Preset-price PLU ... PLU @/FOR PLU Code Quantity; Max. 6 digits ... @/FOR PLU PresetCode Key 4X Quantity Coke-A Quantity; Max. 6 digits 0.80 @ 3.20 T Unit Price Product ... AMT PLU Name Open-price PLU ... PLU Quantity PLU Code ... Unit Price ... @/FOR Quantity NOTES: @/FOR PLU PresetCode Key Unit Price 1. Quantity... Max. 6 digits (Max. 3 digits for integer + max. 3 digits for decimal. Use the [ .
EO1-11126 MA-1350-1 SERIES Purchased Qty 5X Bun-B PLU Name NOTES: 1.50/ 3 2.50 T Whole Package Qty Product Whole Package Price 1. Purchased Qty ... Max. 3 digits (integer only) Whole Package Price ... Max. 6 digits Product (result of SPP) ... Must not exceed 7 digits. You can select the rounding process of the fractions of the product - ROUND UP PRODUCT (initial setting), or ROUND UP ITEM PRICE. (Ask your TOSHIBA TEC representative.) 2. PLU SPP is possible only using the PLUs of SPP Type (i.e.
EO1-11126 MA-1350-1 SERIES Preset Price Open When an open price must be entered through a Preset-price Department, use the [PR OPEN] (or [OPEN]) key to release the preset-price status temporarily. Depress PR OPEN (or OPEN ) prior to or any time during the entry sequence of the following operations: Entry of One Department Item Department Quantity Extension Department SPP Other Income Department Entry Single-item Department Entry NOTES: 1. A price entry by Preset Price Open cannot be repeated. 2.
EO1-11126 MA-1350-1 SERIES Percent Discount, Percent Charge Department or PLU Item Entry (or %... Positive Previous Balance Entry (debit balance on customer) ) .................................... for the Preset Rate %+ %- %+ (or Manual Rate DRINK %5% Sale Item Entries ) .......... for the Manual Rate ST %- (or Dep 3 (DRINK) $6.00 0.30- 5% on $6.00 = $0.30 is discounted. ) .............................. for the Preset Rate %+ ... 6.00 T %- (or %+ ) ....
EO1-11126 MA-1350-1 SERIES NOTES: 1. For entering a Dollar Discount that will cause the sale total into negative (credit balance), one of the following can be selected (ask your TOSHIBA TEC representative): If status “Credit Balance Prohibited” (initial status) is selected: Over-subtraction of the sale total by Dollar Discount causes an error. If status “Credit Balance Allowed” is selected: Over-subtraction of the sale total by Dollar Discount is possible. 2.
EO1-11126 MA-1350-1 SERIES 4. None of PLUs, Negative Departments, Other Income Departments, Void, Returned Merchandise entries are possible along with the [STR CPN] key within one item. 5. The Store Coupon amount will subtract the Department Amount but will not affect the Department Item Count in the report memory. 6. The [STR CPN] key has its own Tax (PST) Status, GST Status, and Food Stamp Status programmed.
EO1-11126 MA-1350-1 SERIES NOTES: 1. When an item previously entered with a Percent Discount or Percent Charge is canceled, the item can be voided with the Percent Discount/Charge by attaching the [VOID] key to the same entry procedure as previous entry. At Entry MEAT %- At Void VOID MEAT %- 7.00 TF 5% 0.35- 7.00-TF 5% 0.35 The process of the amount resulted from % calculation is reversed at Void. 2. The Void entries are usually possible only inside a sale.
EO1-11126 MA-1350-1 SERIES Returned Merchandise Depress RTN MDSE prior to or any time (before the final key at the latest) during the entry sequence of the following operations: RTN MEAT Department Entries PLU Entries Percent Discount/Charge on a Department or PLU Item (NOTE 1) NOTES: 7.00-TF Dept. 1 (MEAT) $7.00 is entered but returned. 1.
EO1-11126 MA-1350-1 SERIES Subtotal Read Sale Item Entries NOTES: ST SUBTL 22.91 Subtotal Amount 1. When the [ST] key is depressed, the sale total is displayed and printed. However, you can select not to print (display only) by a system option. (Ask your TOSHIBA TEC representative.) Even if this non-print option is selected, the subtotal amount is automatically printed when a Percent Charge/Discount or Dollar Discount entry follows a subtotal entry. 2.
EO1-11126 MA-1350-1 SERIES 2) Media Tender Sale Item ( Entries ST or TXBL TL ... ) AT/TL Tendered Amount TAX TLTAL CATEND CHANGE JONES 0.36 3.96 4.00 0.04 (or Tax Amount Sales Total Cash Amount tendered Change due CHECK TEND $5.00 , , chg , $10.00 CPN , CASH 3 MISC , ) (Cash Payment 1 to 3 Keys) 0160 15:42TM 3) Multi-Tender (short-tender repeated by the same media) Example) Sale Item Entries ( ST or TXBL TL ...
EO1-11126 MA-1350-1 SERIES 6. When the HALC (High Amount Listing Capacity) is programmed to the respective tendering amounts of the media keys, tendering amount through the media key cannot exceed the programmed one in the REG position. Food Stamp Tender All the items are entered for the customer. FSTL TEND FSTL TEND ... ........ Amount of Food Stamps actually tendered NOTE 2 Displays (and prints) the Food-stampable Total amount, with the “TL” lamp illuminated.
EO1-11126 MA-1350-1 SERIES The customer may pay up to the food-stampable amount in food stamps, and the food-stampable amount is tax-exempted regardIess of the actual amount paid in food stamps. NEW JERSEY Type FISH DRINK FS/TL F-STMP TAX CASH 6.00 TF 2.00 T 6.00 6.00 0.30 2.
EO1-11126 MA-1350-1 SERIES (4) Percent charge/discount on a previous balance ... ... ( PB+ Previous Balance NOTES: ) %+ Rate 1. The [%-] key operates the same for percent discouting. 2. The previous balance entered through [PB-] (credit balance for customer) will not allow %+ or %- operation. TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 PB+ MEAT 3X Coke-B SUBTL TAX Chg R/A CASH NEW BAL JONES #112300 0.
EO1-11126 MA-1350-1 SERIES 3. When the program option “Validation Print Compulsory” is programmed to the respective media keys, the drawer will open after performing the validation print. (Ask your TOSHIBA TEC representative.) Post-issue Receipt RECEIPT ISSUE A sale is finalized with the “R OFF” lamp illuminated. NOTES: .................................. The receipt for the last sale is issued. 1.
EO1-11126 MA-1350-1 SERIES Food Stamp Modification Food Stamp status of the Department/PLU or the required key is reversed. Depress FS/M prior to or any time (before the final key at the latest) during the entry sequence of the following operations: Department Entries PLU Entries Percent Discount/Charge Dollar Discount Vendor Coupon Store Coupon Tax Exemption All the items are entered for the customer.
EO1-11126 MA-1350-1 SERIES NOTES: 1. After depressing the [EX] key, the sale must only be finalized (for payment through media keys including the [CUR] keys). 2. Tax Exemption transaction cannot be item-corrected. 3. If the “Non-taxable Amount Limit” is set for certain areas in Canada, using the [GST/M] key will cause an error and GST Exemption is not allowed. Manual Tax Entry Sale Item Entries ... ....... The entered tax amount is printed and added to the sale. TAX Tax Amount required NOTES: 1.
EO1-11126 MA-1350-1 SERIES 3. When over-tendered: The sale is finalized, the drawer opens, and the change due is displayed in the domestic currency which is to be returned to the customer. When short-tendered: The sale is not finalized. Any other media tendering may follow (refer to the section “Multi-tender, Split Tender” on page 36). 4.
EO1-11126 MA-1350-1 SERIES 3. If the “SLIP” lamp flickers during registrations, it indicates that the last item just entered has been programmed to require validation print. In this case, no other operations can follow until the validation print of the item is performed. 4. The following options are selective in relation to validation print: 1) Print Format a) Consecutive No. Print/Non-print b) Cashier No.
EO1-11126 MA-1350-1 SERIES -- Receipt Print -Remote Slip Print TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 MEAT Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 MEAT Bun-A DRINK SUBTL TAX Chg JONES 0225 14:44TM Salmon 8X JONES 0225 14:44TM Salmon 8X #112300 7.00 TF @ 15.00 TF 3.00/ 8 3.00 T 15.00 T 40.00 4.25 44.25 3X Bun-A DRINK SUBTL TAX Chg 7.00 TF 5.00 @ 15.00 TF 3.00/ 8 3.00 T 15.00 T 40.00 4.25 44.25 3X 5.
EO1-11126 MA-1350-1 SERIES 14. Paper Roll Replacement and Other Maintenance When a red line appears on the edge of the paper roll, follow the steps below to replace the paper roll with a new one. WARNING! Care must be taken not to injure yourself with the paper cutter. Replacing the Receipt Roll X REG MGR 1 - OFF Turn the Control Lock to the REG position using the Control Key.
EO1-11126 MA-1350-1 SERIES 5 Load new paper roll as described in Chapter 8 on page 12. Replacing the Journal Roll X REG MGR - OFF 1 Turn the Control Lock to the REG position using the Control Key. Z SET 2 To remove the Printer Cover, insert the Printer Cover Key to the Printer Cover Lock, and then turn it 90˚ clockwise. 3 VALI DATE TX M Depress the [JF] key to wind up enough of the Journal Paper, then cut the paper as shown in the figure. Depress the [JF] key to feed the remaining paper end.
EO1-11126 MA-1350-1 SERIES 4 Remove the wound-up portion of the paper by pulling it sideways. 5 Load new paper roll as described in Chapter 8 on page 12. Replacing the Ribbon Cassette This Ribbon Cassette is a consumable part and a TOSHIBA TEC’s exclusive. Ask your TOSHIBA TEC representative about the order of the Ribbon Cassette. 1 X REG OFF Turn the Control Lock to the OFF position using the Control Key.
EO1-11126 MA-1350-1 SERIES 3 Remove the old Ribbon Cassette by pulling it in the direction of the arrow mark. 4 Install a new one as shown in the figure. After installing the Ribbon Cassette, turn the knob of the Ribbon Cassette in the direction of the arrow mark several times to remove the slack on the ribbon. 5 After replacing the Ribbon Cassette, attach the Printer Cover.
EO1-11126 MA-1350-1 SERIES 2 To remove the Printer Cover, insert the Printer Cover Key to the Printer Cover Lock, and then turn it 90° clockwise. 3 Remove the Store Name Stamp by pulling it in the direction of the arrow mark. Apply ink from the shaded places. 4 Apply only two or three drops. Stamp may not print dark immediately. Allow time for ink to saturate the stamp. 5 Install the stamp by inserting it in the direction of the arrow mark. 6 Attach the Printer Cover.
EO1-11126 MA-1350-1 SERIES 7 X REG MGR - OFF After replenishing ink, depress the [#/NS] key to check the density of the printed message. Z SET Manual Drawer Release and Lock The drawer opens automatically when a registration is performed. In the event of a power failure or other trouble, the drawer can be opened manually in the following manner. WARNING! When opening the cash drawer, be careful not to let the drawer hit any person. Releasing Remove the CDC Cap.
EO1-11126 MA-1350-1 SERIES 2 When it stops again by the roller fixed in the drawer case, lift it and pull it again. Media Slot The Media Slot provided at the front of the drawer is used to put non-cash media such as check in the drawer without opening it. The non-cash media put from this slot are kept under the Money Case, therefore you can keep them in secret. Media Slot Non-cash media are kept here.
EO1-11126 MA-1350-1 SERIES 15. In Case of the Power Failure If a power failure occurs during business hours, all sales data stored in the memory are automatically protected by the batteries installed in the register. When any data was being printed on the power failure, the same data is automatically printed at the power recovery. In case of the power failure, it is suggested to check the receipt print contents before you hand the receipt to the customer. MEAT 7.00 TF ∗ P.FAIL ∗ MEAT 7.
EO1-11126 MA-1350-1 SERIES Paper roll wrinkles. Cause 1: Paper roll is not placed correctly, or placed on the skew. Measure: Place the paper roll correctly. (Refer to page 46.) Cause 2: Failure of the printer itself Measure: Ask the store where purchased. Printer prints nothing. Cause 1: Ribbon cassette is not installed. Measure: Install the ribbon cassette. (Refer to page 15.) Cause 2: Ribbon cassette reaches its life, deteriorates, or is damaged. Measure: Replace the ribbon cassette with a new one.
EO1-11126 MA-1350-1 SERIES Paper jam has occurred. Cause: Paper roll is placed on the skew, or foreign substance exists in the paper path of the inside of the printer. Measure: Remove the jammed paper as follows. 1 To open the upper side of the printer, press simultaneously two levers (green) provided on both sides of the printer in the direction of the arrow. 2 Raise up the upper side of the printer in the direction of the arrow, then remove the jammed paper.
EO1-11126 MA-1350-1 SERIES Some segment is not displayed, display shimmers, or illumination of the display is uneven. Cause 1: Failure of the LED Measure: Ask the store where purchased. 6. Trouble during Normal Operations NOTE on changing the Control Lock position: Changing the Control Lock position during sales entries or programming causes an error. To clear the error, return the Control Lock to the original position. However, changing the Control Lock position to the OFF does not cause an error.
EO1-11126 MA-1350-1 SERIES 8. Trouble in the SET Position Operations in the SET position cannot be carried out. Cause 1: Control Lock is not in the SET position. Measure: Turn the Control Lock to the SET position using the Control Key. Cause 2: Condition for the programming is not satisfied. Measure: Check the condition for the programming . Cause 3: Operation procedure is incorrect. Measure: Check the operation procedure you attempted. 17. Specifications Size .............................................
EO1-11126 MA-1350-1 SERIES MANAGER’S GUIDE Manager's Guide T.O.C.
EO1-11126 MA-1350-1 SERIES TABLE OF CONTENTS Page 1. Operations in “MGR” Mode .............................................................. 1 Items programmed to require Manager Intervention ................................... 1 Listing Capacity Release ............................................................................. 2 2. Operations in “ - ” Mode ................................................................. 3 3. Read and Reset Reports ....................................................
EO1-11126 MA-1350-1 SERIES 1. Operations in “MGR” Mode This chapter describes operations to be performed in the “MGR” position of the Control Lock, which the Store Manager can access using the MGR or MA key. Items programmed to require Manager Intervention During daily sale entry operations, the cashier may call for Manager Intervention. The following is the operation flow of Manager Intervention. 1) During operations, the cashier comes across an item that requires Manager Intervention.
EO1-11126 MA-1350-1 SERIES Operations and Manager Intervention Status OPERATION MGR Position Not required Required Credit Balance (oversubtraction of the sale by [DOLL DISC], [VND CPN], [STR CPN] and [VOID] keys) Negative Department or negative PLU Entries Negative-balance Sale Finalization by Noncash Media Kyes. NOTES: Reference As for the status change, ask your TOSHIBA TEC representative. 1.
EO1-11126 MA-1350-1 SERIES 2. Operations in “ - ” Mode This chapter describes operations to be performed in the “ - ” position of the Control Lock, which the Store Owner or a person so authorized can access using the MA key. Instead of using the [RTN MDSE] or [VOID] keys in the “REG” or “MGR” mode for deleting individual sale items, the “ - ” mode automatically processes positive items into negative and negative into positive.
EO1-11126 MA-1350-1 SERIES 3. Read and Reset Reports This chapter describes the operation to take each report and its contents. • • • • • The Read (X) reports allow to read the totals but not clear the memory, while the Reset (Z) reports allow to read the totals and, at the same time, clear all the resettable totals when the report has been taken. The symbol “X” is printed at the top of Read Reports, while “Z” is printed on Reset Reports to indicate the type of report.
EO1-11126 MA-1350-1 SERIES Periodical Reports Report Name Key Operation Sample Page * Financial Read * Financial Reset Control Lock: X Control Lock: Z → 2 0 * All Cashier Read (NOTE 3) * All Cashier Reset (NOTE 3) Control Lock: X Control Lock: Z → 4 Control Lock: X Control Lock: Z → 2 1 AT/TL 13 2 2 AT/TL 14 All Department Read (NOTE 2) All Department Reset (NOTE 2) Department Gross Profit Read NOTES: Control Lock: X → AT/TL AT/TL 6 16 1.
EO1-11126 MA-1350-1 SERIES Financial Read or Reset Report (Daily or Periodical) TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 #112300 Date, Register No. X: Z: GTX: GTZ: Daily Read Daily Reset Periodical Read Periodical Reset Report Type Symbol Z GT 10105581.31 Grand Total (non-resettable) (Initial Status: Print) 10106672.51 185 988.46 44 244.
EO1-11126 MA-1350-1 SERIES CASH 44CU CHECK 3CU Chg 8CU MISC 1CU CPN 0CU FS TL 1CU R/A PO CASH ID CHECK ID Chg ID MISC ID CPN ID FSID FS CG CORR VOID MISC VD ALL VD %S.CPN -DP TL RTN -TAX REGTRF TL TRF+ GT TRF- GT TRF+ TRFPB TL 3CU PB R/A PB PO NON GST GST TXBL GST INC TXBL1 TXBL2 TXBL3 TAX EX 2CU GST EX TAX1EX TAX2EX TAX3EX Cash Sales: Customer Count, Amount Check Sales: Customer Count, Amount 773.43 550.88 Charge Sales: Customer Count, Amount 336.
EO1-11126 MA-1350-1 SERIES FS EX1 FS EX2 FS EX3 N. NS CUR1 CUR2 NO SALE VALI CTR MEAT 10.00% FISH 15.00% DRINK 20.00% BAKERY 25.00% TOTAL 14.79% 0006Z 0.00 0.00 0.00 0.00 2 120.00 1 15.00 2 6 24.41 20.19 11.98 20.27 76.85 0263 20:37TM NOTE: Food Stamp Tax 1 Exempt Amount (Printed only when ILLINOIS or Food Stamp Tax 2 Exempt Amount NEW JERSEY type of Food Food Stamp Tax 3 Exempt Amount Stamp feature is selected.
EO1-11126 MA-1350-1 SERIES - Memory Balance Memory Balance applicable to the US Version Grand Total = Sum of Daily Gross Sales NET GT = Sum of Daily All Media Sales Gross Sales = (Sum of Depts.; NOTE 1) + (Sum of Taxes) + (Percent Charge) + (Percent Discount on Line Item) + (Sum of Negative Depts.) + (Item Correct) + (Void) + (Returned Merchandise) + (“ - ” Mode) + (Store Coupon) + (All Void; NOTE 2) + (Negative Tax) Net Sales with Tax = (Sum of Depts.
EO1-11126 MA-1350-1 SERIES Memory Balance applicable to the CA GST (Exclusive) Version Grand Total = Sum of Daily Gross Sales NET GT = Sum of Daily All Media Sales Gross Sales = (Net Sales with Tax) + (Percent Discount on Line Item) + (Sum of Negative Depts.) + (Item Correct) + (Void) + (Returned Merchandise) + (“ - ” Mode) + (Store Coupon) + (All Void; NOTE 2) + (Negative Tax) Net Sales with Tax = (Sum of Depts.
EO1-11126 MA-1350-1 SERIES Memory Balance applicable to the CA GST (Inclusive) Version Grand Total = Sum of Daily Gross Sales NET GT = Sum of Daily All Media Sales Gross Sales = (Net Sales with Tax) + (Percent Discount on Line Item) + (Sum of Negative Depts.) + (Item Correct) + (Void) + (Returned Merchandise) + (“ - ” Mode) + (Store Coupon) + (All Void; NOTE 2) + (Negative Tax) + (Exempted GST) Net Sales with Tax = (Sum of Depts.
EO1-11126 MA-1350-1 SERIES Daily Hourly Sales Read or Reset Report TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 X10: Daily Read Z10: Daily Reset #112300 Z10 08:00TM 1CU 09:00TM 4CU 10:00TM 14CU 13:00TM 24CU 16:30TM 18CU 19:00TM 0001Z Report Type Symbol 5.00 Sales Data in Hourly Range from 19 : 01 yesterday to 8 : 00 No sales recorded Sales Data (Customer Count & Amount) in Hourly Range from 8 : 01 to 9 : 00 43.
EO1-11126 MA-1350-1 SERIES All Departments Read or Reset Report (Daily or Periodical) TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 #112300 X11 MEAT 31CU 46.97% FISH 18CU 25.90% DRINK 13CU 11.53% BAKERY 12CU 15.61% DP05 5CU DP06 3CU TOTAL FRESH F 22.12% DR & BA 8.24% OTHERS 69.65% TOTAL (Initial Status: Print) NOTE 2 MEAT 10.00% FISH 15.00% DRINK 20.00% BAKERY 25.00% TOTAL 14.79% 44 244.10 40 134.
EO1-11126 MA-1350-1 SERIES Department Gross Profit Read (Daily or Periodical) X12 NOTE MEAT 10.00% FISH 15.00% DRINK 20.00% BAKERY 25.00% 20.27 76.85 Average Gross Profit Rate, Total of Gross Profit Amount 24.41 20.19 11.98 TOTAL 14.
EO1-11126 MA-1350-1 SERIES Cashier Read or Reset Report (Daily or Periodical) Daily Cashier Read or Reset Report TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 #112300 Z SMITH GS NS NS HASH TL 6 26.68 3 18.00 3 18.48 0 0.00 TOTAL 4CU CASH ID CHECK ID Chg ID MISC ID CPN ID FSID NEG1 NEG2 PO TAX 0002Z X: Daily Read Z: Daily Reset 18.48 -2.52 1 10.00 0 0.00 0 0.00 0 0.00 2 11.00 8.20 0.00 0.00 0.
EO1-11126 MA-1350-1 SERIES Periodical Cashier Read or Reset Report TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 #112300 Z04 JONES GS NS NS HASH TL TOTAL 56CU NEG1 NEG2 PO TAX SMITH GS NS NS HASH TL X04: Periodical All Cashier Read Z04: Periodical All Cashier Reset Report Type Symbol 179 627.52 139 495.72 139 531.12 3 1200.00 Sales Data by Cashier 1 (JONES) (format same as in Daily Report) 1726.92 96.40 4.20 6.50 35.40 6 26.68 3 18.00 3 18.
EO1-11126 MA-1350-1 SERIES 4. Changing the Programmed Data This chapter is provided for the store programmer or the store manager who may have to change the programmed data of the MA-1350-1 series ECR on a daily, weekly, or monthly basis. Usually, all the basic program data required for your store should be set before delivering the product by your local TOSHIBA TEC representative. However, to change or add program data, please refer to this chapter.
EO1-11126 MA-1350-1 SERIES Character Code Entry Method: CHARACTER CODE Table: Column Code → 0 1 2 3 4 5 6 0 0 @ J T < Ä ì 1 1 A K U > Ë Ø 2 2 B L V { Ö ¢ 3 3 C M W | É ÷ 4 4 D N X } ë 5 5 E O Y ~ ï II 6 6 F P Z î III 7 7 G Q $ ô 1b 8 8 H R £ û [ 9 9 I S ¥ à [ Row Code → + 8 9 10 11 12 13 14 15 16 No ’ , j t ä â ( Ψ ” .
EO1-11126 MA-1350-1 SERIES Character Setting Operations • To set a regular-sized character, enter the COL (column) code and then the ROW code, followed by the [#/NS] key. Example) To set “B”, enter 12 and depress [#/NS]. To set “j”, enter 120 and depress [#/NS]. • To set a blank instead of a character, enter 169 and depress [#/NS]. • Depress the [@/FOR] key once prior to a regular-sized character entry, and it will be a double-sized character (a blank will also be double-sized).
EO1-11126 MA-1350-1 SERIES NOTES: 1. Numeric keys are used to enter PLU Codes or numeric values of program data, etc. but not to enter the numerics as characters. 2. Characters not shown on the keyboard on the preceding page can be entered by the Character Code Entry Method. 3. After setting operation on this keyboard is completed, operate “82 [@/FOR]” to regain the keyboard layout for registrations.
EO1-11126 MA-1350-1 SERIES NOTES: 1. Numeric keys are used to enter PLU Codes or numeric values of program data, etc. but not to enter the numerics as characters. 2. Characters not shown on the keyboard on the preceding page can be entered by the Character Code Entry Method. Using the PK-2 (PLU Keyboard; hardware option): The PK-2 (hardware option PLU Keyboard) is used to enter the required PLU Code by simply depress the PLU Preset-code Key on the PK-2 keyboard in the “REG”, “MGR”, or “ - ” mode.
EO1-11126 MA-1350-1 SERIES Condition for Programming Operations: At the top of each programming operation sequence in this chapter, “Condition” is attached. Unless the register satisfies this condition, the programming operations will not be allowed. When Condition “After ... Reset” is attached: “After ... Reset” means that the designated reset report must be taken before entering the programming (setting) operation. An error will result if the operation is attempted without taking the report.
EO1-11126 MA-1350-1 SERIES Store Message and Commercial Message Programming Condition: Any time outside a sale Programming Procedure: 1 @/FOR (For sequentially programming lines, the line number specification can be skipped.) ST Declaration of Program No. 1 for Store Message and Commercial Message Programming Repeat for another line. Line No. 1 to 7 NOTE 2 AT/TL ST max. 24 characters/line (See Character Entries at the beginning of this chapter.) To complete this line ...
EO1-11126 MA-1350-1 SERIES Store Message and Commercial Message Programming Receipt Format: Key Operation: Control Lock: SET 1 1 @/FOR ST 1 8 #/NS (H) 1 6 9 #/NS (space) (Line No.
EO1-11126 MA-1350-1 SERIES ST 5 (Line No. 5) ( ST 6 ) (Line No.
EO1-11126 MA-1350-1 SERIES Cashier Name Programming Condition: Any time outside a sale Programming Procedure: Repeat for another cashier. (Max. 8 cashiers) 2 @/FOR ST Declaration of Program No. 2 for Cashier Name Programming Cashier No. 1 to 8 NOTE 3 AT/TL ST max. 8 characters (See Character Entries at the beginning of this chapter.) To complete this name NOTES: ... Character Entries 1. For each cashier name, a maximum of 8 regular-sized characters or 4 double-sized characters may be entered.
EO1-11126 MA-1350-1 SERIES Department Status Programming Condition: After Daily Financial Reset and Periodical Financial Reset (and All PLU Reset if the positive/ negative status is to be changed) When the program option “Department Report separately issued from Financial Report” has been selected: To add to the above conditions, After Daily Department Reset and Periodical Department Reset Programming Procedure: 3 #/NS @/FOR Declaration of Program No. 3 for Department Status Programming Address No.
EO1-11126 MA-1350-1 SERIES NOTES: 1. “Address No.” designation located after the key operation “3 [@/FOR]” can be omitted if unnecessary. When an address No. is designated, the programming of the designated address will be automatically repeated for multiple departments. 2. For each department name, a maximum of 8 regular-sized characters or 4 double-sized characters may be entered. A combination of both types is also available. 3. Department status available is as follows.
EO1-11126 MA-1350-1 SERIES PLU Table Setting, Changing, or Deletion Setting or Changing PLUs: Condition: To change settings of a PLU: When the required PLU sales total memory is zero (i.e. when no sales are made or after a PLU Reset Report is taken to reset the sales data of the PLU into zero) To add new PLUs or to change PLU Name only: Any time outside a sale Programming Procedure: 4 #/NS @/FOR Declaration of Program No. 4 for PLU Table programming Address No.
EO1-11126 MA-1350-1 SERIES NOTES: 1. “Address No.” designation located after the key operation “4 [@/FOR]” can be omitted if unnecessary. When an address No. (1, 2, 4 or 5) is designated, the programming of the designated address will be automatically repeated for multiple PLUs. 2. Max. 500 PLUs are available when the RAM capacity is 32 KB. (Model Name: MA-1350-1-S-XX) Max. 1000 PLUs are available when the following two conditions have been satisfied. • RAM capacity is 128KB.
EO1-11126 MA-1350-1 SERIES Deleting individual PLUs: Condition: When the required PLU sales total memory is zero (i.e. when no sales are made or after a PLU Reset Report is taken to reset the sales data of the PLU into zero) Deleting Procedure: Repeat for other PLUs to be deleted, if any. 4 ITEM CORR @/FOR PLU PLU Code of the PLU to be deleted Declaration same as PLU Programming on the preceding pages. NOTES: AT/TL 1. Deletions are possible PLU by PLU. 2. If all the PLUs must be deleted (i.e.
EO1-11126 MA-1350-1 SERIES Time Setting or Adjustment Condition for Setting: Any time outside a sale Setting Procedure: 5 @/FOR Declaration of Program No. 5 for Time Setting Examples) Time (00 to 23) 1 Minute (00 to 59) Open 8:00am to 7:00pm Closed: every Wednesday ← 1:05 a.m.: 0 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 0 1:32 p.m.: 5 1 3 11-28-1997 3 2 #0 P05 08:30TM AT/TL Issues a receipt. 0037 08:30TM Time now set (8:30 a.m.
EO1-11126 MA-1350-1 SERIES PLU Preset-code Key Setting When there are any keys programmed as PLU Preset-code Keys on the ECR Keyboard, and/or when the PLU Keyboard PK-2 (hardware option) is connected to the ECR, a PLU code may be preset to each of those keys in this operation. Condition: Any time outside a sale Programming Procedure: Repeatable for other keys. 2 7 @/FOR PLU Code Enter through Numeric Keys on the ECR Keyboard (Enter 0 to close the key) Declaration of Program No.
EO1-11126 MA-1350-1 SERIES PK-2 KEYBOARD 1 11 21 31 41 51 61 71 81 91 101 111 121 2 12 22 32 42 52 62 72 82 92 102 112 122 3 13 23 33 43 53 63 73 83 93 103 113 123 4 14 24 34 44 54 64 74 84 94 104 114 124 5 15 25 35 45 55 65 75 85 95 105 115 125 6 16 26 36 46 56 66 76 86 96 106 116 126 7 17 27 37 47 57 67 77 87 97 107 117 127 8 18 28 38 48 58 68 78 88 98 108 118 128 9 19 29 39 49 59 69 79 89 99
EO1-11126 MA-1350-1 SERIES Department Preset Price Setting or Changing Condition: Any time outside a sale Programming Procedure: To set Open Department (to allow manual amount entries) NOTES 1,2,3 Dept. AT/TL Preset Price (max. 6 digits; 0 to 999999; resulting in $0.00 to $9999.99) Repeat for other Department Keys, if necessary. NOTES: 1. All the Department Keys are open departments (with no preset prices) as initial status. 2.
EO1-11126 MA-1350-1 SERIES PLU Preset Price Changing When only changing preset prices of PLUs as part of daily requirements, this operation is quicker than operating “PLU Table Setting, Changing, or Deletion.” Condition: Any time outside a sale Programming Procedure: Repeat for other PLUs if necessary. PLU NOTE 3 PLU Code max. 4 digits; 1 to 9999 NOTE 1 For non-SPP PLUs or for no change of Whole Package Quantity ST New Whole Package Quantity max. 2 digits; 0 to 99 NOTE 4 NOTES: ...
EO1-11126 MA-1350-1 SERIES PLU Price Change Setting Receipt Format Key Operation: Control Lock: SET PLU Code 2 0 0 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 New Preset Price PLU 5 0 0 #/NS Open 8:00am to 7:00pm Closed: every Wednesday AT/TL 11-28-1997 #0 Link Department No. P00 02 Salmon PLU200 5.
EO1-11126 MA-1350-1 SERIES Register No. Setting When multiple registers are used in one store, or to distinguish this register from others used by other stores in the same chain, set the Register Number in the following procedure. Condition: Any time outside a sale Programming Procedure: #/NS Register Number max. 6 digits; 0 to 999999 Example) No. 112300: 1 1 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 2 3 0 Open 8:00am to 7:00pm Closed: every Wednesday 0 11-28-1997 #0 Register No.
EO1-11126 MA-1350-1 SERIES 2. Calculate the required foreign currency value equivalent to the domestic currency value “1”. Then the obtained value is the Exchange Rate value to be entered in the setting operation above. Example) Domestic Currency is US$: 1 cent = XXXX . XXXXXX centimes (French Franc) = XXXX . XXXXXX pfennigs (Deutsche Mark) = XXXX . XXXXXX yen (Japanese Yen) etc. Enter this value as the foreign currency exchange rate. 3.
EO1-11126 MA-1350-1 SERIES * HALC ........... High Amount Listing Capacity (to be set in a 2-digits code) 4 ........... indicate $39.99 ................... equal to or smaller than $39.99 → → Example) 4 digits Value of the top digit NOTES: 1. To reset an individual media listing capacity, enter 0 before media key depression in the above operation. 2. The HALC of each tender media is effective only when the media key is used for tendering but not when it is used as Total key. 3.
EO1-11126 MA-1350-1 SERIES PK-2 KEYBOARD 1 11 21 31 41 51 61 71 81 91 101 111 121 2 12 22 32 42 52 62 72 82 92 102 112 122 3 13 23 33 43 53 63 73 83 93 103 113 123 4 14 24 34 44 54 64 74 84 94 104 114 124 5 15 25 35 45 55 65 75 85 95 105 115 125 6 16 26 36 46 56 66 76 86 96 106 116 126 7 17 27 37 47 57 67 77 87 97 107 117 127 8 18 28 38 48 58 68 78 88 98 108 118 128 9 19 29 39 49 59 69 79 89 99
EO1-11126 MA-1350-1 SERIES 5. Program Data Verification Whenever programming operations are performed, it is recommended to issue Program Verification receipts to check the programmed data before entering any other operation. Operating Procedure Condition: Any time outside a sale Operating Procedure: MGR - X REG Z SET ← OFF Illuminated: Verification data is printed on journal only. Extinguished: Verification data is printed on both journal and receipt.
EO1-11126 MA-1350-1 SERIES Department Preset Price Read TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 Department Name Department No. #112300 PX 01 02 03 04 05 06 MEAT FISH DRINK BAKERY DP05 DP06 7.00 Preset Price (Those with blank price are Open-price Departments.) NOTE: 0319 23:20TM For changing the preset price or the Openprice/Preset-price status of any department, refer to “Department Preset Price Setting or Changing” in Chapter 4.
EO1-11126 MA-1350-1 SERIES PLU Table Read TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 PLU Code PLU100 PLU Name PLU101 PLU200 PLU201 PLU300 PLU301 PLU400 PLU401 PLU500 #112300 PX 01 2.00 Pork 01 3.00 Beef 02 5.00 Salmon 02 2.00 Shrimp 03 1.00 Coke-A 03 1.00 Coke-B 04 3.00/ 8 Bun-A 04 1.50/ 3 Bun-B 05 0.50 PLU500 Link Department No. Preset Price (Blank Price means an Open-price PLU.
EO1-11126 MA-1350-1 SERIES Other Programmed Data Read TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 #112300 PX V.CPN CATEND CHECK Chg MISC CPN FS TL %+ %GST CUR1 CUR2 01 CASH 02 CASH 20.00 34 00 00 00 00 35 86 10% 5% 7% 20.00 0.7143∗ 0.5321∗ 10.00 20.
EO1-11126 MA-1350-1 SERIES System Option Read 1 System Option Read 2 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 TEC STORE 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm Closed: every Wednesday 11-28-1997 Open 8:00am to 7:00pm Closed: every Wednesday #112300 11-28-1997 #112300 SET Bit Nos. SET Bit Nos.
EO1-11126 MA-1350-1 SERIES - 46 - Make a copy of this sheet and use it when you input characters directly on the normal keyboard.
TEC TEC CORPORATION
