Electronic Computing Scale Owner's Manual

ManualsBrandsToshiba ManualsScaleTEC EM1-31076

TEC Electronic Computing Scale

SL-9000/9000N-FFH-US/CA/QR

Owner’s Manual

Summary of content (92 pages)

PAGE 1
TEC Electronic Computing Scale SL-9000/9000N-FFH-US/CA/QR Owner’s Manual
PAGE 2
PAGE 3
TABLE OF CONTENTS Page 1. INTRODUCTION ..................................................................................................... 1- 1 1.1 APPLICABLE MODEL ................................................................................... 1- 2 1.2 ACCESSORIES............................................................................................. 1- 2 2. SPECIFICATION ..................................................................................................... 2- 1 2.1 SCALE ........
PAGE 4
Page 11. PROGRAMMED DATA VERIFICATION REPORTS................................................. 11- 1 12. PASSWORD SECURITY ......................................................................................... 12- 1 12.1 SETTING PASSWORD AND PROTECT MENU............................................. 12- 1 12.2 CALLING MENU BY ENTERING PASSWORD .............................................. 12- 3 13. OPERATING PROCEDURES ..................................................................................
PAGE 5
PAGE 6
1. INTRODUCTION 1. INTRODUCTION 1. INTRODUCTION Thank you for purchasing the TEC SL-9000 electronic computing scale. The TEC SL-9000 is designed to be hung from the ceiling. As you will discover, it has many features and functions designed for user friendliness as well as complete customer satisfaction. The 256x64 dot fluorescent display provides customers with ample information, the 216 speed keys realize a higher degree of operability, and the 3 inch/sec. print speed ensures fast and clear printing.
PAGE 7
1. INTRODUCTION 1.1 APPLICABLE MODEL 1.1 APPLICABLE MODEL • SL-9000-15M-FFH-CA • SL-9000-15M-FFH-QR • SL-9000-30M-N-FFH-US • SL-9000-15M-N-FFH-CA • SL-9000-15M-N-FFH-QR The description of the model number is as follows. SL-9000-30M-N-FFH-US Destination Code ex.) US, CA, QR, etc. Max. Capacity 30M: 30 lbs (decimal pound /multi-interval) 15M: 15 Kg (multi-interval) Scale Type H: Hanging scale Display Type FF: Fluorescent full dot display N: LAN (Option) is available.
PAGE 8
2. SPECIFICATION 2.1 SCALE 2. SPECIFICATION 2.1 SCALE Item US CA Maximum Capacity 30 lb 15 Kg (30 lb) Minimum Scale Division 0.005 lb (0 to 15 lb.) 0.002 Kg (0 to 6 Kg) 0.005 Kg (6 to 15 Kg) 0.005 lb (0 to 15 lb) 0.01 lb (15 to 30 lb) 0.01 lb (15 to 30 lb.) QR Display Range 0 to 30.05 lb 0 to 15.025 Kg (0 to 30.05 lb) Maximum Tare 2.000 lb 1.000 Kg (2.205 lb) Unit Price Presettable $ 0.01 to 99.99 $ 0.01 to 99.99 0 to 99999 Minimum Price Display $ 0.01 $ 0.
PAGE 9
2. SPECIFICATION 2.2 OPTION 2.2 OPTION Option Name LON Connector TM8P-88P LON LON Terminal Resistor 285D-8P LON Cable S-STLAN-2P (200 m/roll) Model No. or Part No. Part No. EAJ-0028001 Part No. EAJ-0029001 Description Source A modular connector used to connect scales to each other in a LON configuration. A modular resistor attached to the scales connected at both ends of the LON configuration. An 8-pin telephone cable used with the LON connectors attached to both ends of the cable.
PAGE 10
3. APPEARANCE 3. APPEARANCE 3. APPEARANCE LON Interface LAN Interface (SL-9000N option) TMCC Interface (Option) Power Inlet Rear Display Front Display Main Switch Power Keyboard Frame Printer Cover Operation/Speed/ Programming Keyboard CMT/PL-3 Interface Print Head Platter NOTE: To set the speed/operation key sheet, open the keyboard frame and insert the two tabs of the key sheet into the two slots of the keyboard frame bottom.
PAGE 11
4. DISPLAY 4.1 US TYPE 4. DISPLAY 4.1 US TYPE n Front Display Panel SL-9000N x o CAPACITY n WEIGHT e=d 0∼15 lb 0.005 lb 15∼30 lb 0.01 lb SCROLLING MESSAGE INDICATES SCALE AT ZERO Rear Display Panel SL-9000N CAPACITY 4- 1 WEIGHT e=d 0∼15 lb 0.005 lb 15∼30 lb 0.
PAGE 12
4. DISPLAY 4.2 CA/QP TYPE 4.2 CA/QR TYPE n Front Display Panel SL-9000N x o CAPACITY CAPACITÉ n WEIGHT e=d WEIGHT e=d 0∼6 kg 0.002 kg 0∼15 lbs 0.005 lbs 6∼15 kg 0.005 kg 15∼30 lbs 0.01 lbs Rear Display Panel SL-9000N CAPACITY CAPACITÉ WEIGHT e=d WEIGHT e=d 0∼6 kg 0.002 kg 0∼15 lbs 0.005 lbs 6∼15 kg 0.005 kg 15∼30 lbs 0.01 lbs NOTE: For the SL-9000 model, the model name on the display panel is “SL-9000”.
PAGE 13
5. KEY LAYOUT 5.1 PROGRAMMING KEYBOARD 5. KEY LAYOUT 5.1 PROGRAMMING KEYBOARD NOTE: ■ Blank keys have no function. Programming Keyboard Function Name of Key CLEAR SHIFT Function 1. Clears numeric data just entered. 2. Releases the scale from the error mode. Selects the upper case or lower case. SET NEXT Calls the PLU # which follows the PLU # currently called. Sets the media transparency on the sensor. NEXT PLU Calls the PLU # registered right after currently called PLU #.
PAGE 14
5. KEY LAYOUT 5.1 PROGRAMMING KEYBOARD Name of Key − ← → Function 1. Displays the preceding PLU data. 2. Used to set an auto code. 3. Calls the preceding label format # when setting the print position. Moves the cursor to left. Moves the cursor to right. DELETE (A) 1/2 1. Deletes a character selected by the cursor when setting the commodity name or message. 2. Sets a unit price per 1/2 lb. INSERT 1 1. Inserts a space at the cursor position when setting the commodity name or message. 2.
PAGE 15
5. KEY LAYOUT 5.2 OPERATION KEYBOARD AND SPEED KEYBORAD 5.2 OPERATION KEYBOARD AND SPEED KEYBOARD LB/kg (4) (3) NOTES: 1. Pressing the key enables another 108 PLUs assignment. 2. When the initial setting #8-7 is set to 1 (SL-9000) or #28-4 is set to 1 (SL-9000N), the (3) key will function as a Tare% key instead of a speed key. 3. When the initial setting #12-8 is set to 1, the (4) key will function as an AUTO/MANUAL key instead of a speed key.
PAGE 16
5. KEY LAYOUT 5.2 OPERATION KEYBOARD AND SPEED KEYBORAD ■ Operation Keyboard Function Name of Key VOID Corrects data just after the registration. 1. Selects the speed key page. 2. Selects the function for change Print/OFF. ◇ Returns to the main menu. ESC. PROG. POWER 1/2 Function 1/4 Accesses print item, auto message timer, print format and issue mode selection mode. Turns the display on/off when the scale power is on. Changes between 1/2 lb and 1/4 lb (US type only).
PAGE 17
6. PROCEDURE BEFORE OPERATION 6. PROCEDURE BEFORE OPERATION 6. PROCEDURE BEFORE OPERATION 1. 2. 3. 4. Ask an authorized installing dealer for the scale installation. Please contact your nearest TOSHIBA TEC representative. Hang the platter arm from the scale. (See page 7-1.) Load the label or receipt. Set the following programming menus: Menu Page 2 2 1 ITEM No. Programming Name 0 PRINT FORMAT 1 DATE/TIME SETTING 1 PLU DATA SETTING If necessary, set the following program menu: Menu Page 1 1 1 1 1 1 5.
PAGE 18
7. INSTALLATION PROCEDURE 7. INSTALLATION PROCEDURE 7. INSTALLATION PROCEDURE ■ Scale installation on the wall or ceiling The installation should be an authorized installing dealer. Please contect your nearest TOSHIBA TEC representative. ■ Platter 1. Attach the two platter mount plates to the platter arm with the four D-4x8 screws. Screw Platter Arm Platter Mount Plate 2. Fit the notch of the platter arm on the joint nut of the scale.
PAGE 19
8. REMOVAL AND REPLACEMENT OF RECEIPT/LABEL 8. REMOVAL AND REPLACEMENT OF RECEIPT/LABEL 8. REMOVAL AND REPLACEMENT OF RECEIPT/LABEL 1. Open the printer cover and turn the head-up lever to the anticlockwise. 2. Pull out the roll stopper and backing paper stopper, then remove the receipt/label core with the backing paper. You can loosen the backing paper by turning the paper winding shaft anticlockwise.
PAGE 20
8. REMOVAL AND REPLACEMENT OF RECEIPT/LABEL 8. REMOVAL AND REPLACEMENT OF RECEIPT/LABEL 4. Insert the tip of the receipt/label into the print head. 5. Align the two media guides with the right edge of the receipt/label. Media Guide Media Guide 6. Thread the receipt/label as shown below. NOTE: Labels and receipts should be left-aligned as viewed from the front of the machine, and always threaded in parallel with the media shaft and the print head. Failure to do this may cause a paper jam or a skew feed.
PAGE 21
9. OUTLINE OF OPERATION 9. OUTLINE OF OPERATION 9. OUTLINE OF OPERATION ② Main Menu Main Power Switch ON Menu#1 Select the Menu # Display OFF ① Other than Menu #1. Press the POWER key Password Press the POWER key Unnecessary Necessary Scanning Display Password Input REG Menu REWRAP Menu POWER Key REPORT Menu MARK DOWN Menu Press RESET Menu PROG Menu Display OFF SECURITY Menu ① No Press ESC. Key Press ② No Press Return to each mode NOTES: 1.
PAGE 22
10. PROGRAMMING PROCEDURES ■ How to access to Programming Menu 10. PROGRAMMING PROCEDURES ■ How to access to Programming Menu Enter a menu number ESC. 0 Select the programming menu page. unnecessary Password Programming starts neccesary Enter the Password Programming completes ◇ Select an item No. (See next page.) 0 ∼ 9 PROG. NOTES: 1. When the selected menu ( 0 ) is protected from an access, refer to Section 12.2 and enter the password. 2. In Section 10.1, 10.2 and 10.
PAGE 23
10. PROGRAMMING PROCEDURES ■ Title and Contents of Programming Menu ■ Title and Contents of Programming Menu Table 1. NO. TITLE MENU PAGE ITEM NO.
PAGE 24
10. PROGRAMMING PROCEDURES ■ How to enter characters ■ How to enter characters Use the following procedure to enter a commodity name, address and ingredient message. Example) 1st line: TEC STORE 2nd line: (TEL) 0123-45-6789 T E C S SPACE O T R E RETURN 1/4 1 st line content DELETE SHIFT ( SHIFT T E (A) 1/2 E L 6 7 8 9 2 nd line content NOTES: 1. ← and → keys are the cursor keys. 2.
PAGE 25
10. PROGRAMMING PROCEDURES 10.1 PLU DATA EDIT 10.1 PLU DATA EDIT Menu Page: 1 Item No.: 0 In this procedure, use operation keys (except when calling a PLU by using a speed key). The unit price stored in a PLU can be changed with this menu. a
Page 1 0 Enter the PLU # NEXT PLU PRT * or VOID Enter the Speed key # ◇ Speed key Page 1ÖPage 2 a Change the unit price (max. 4 digit) PRT * PROG. Page 1 ESC. Main TEST NOTES: 1.
PAGE 26
10. PROGRAMMING PROCEDURES 10.2 PLU DATA SETTING 10.2 PLU DATA SETTING Menu Page: 1 Item No.: 1 Setting or changing the contents of PLU (PLU#, UPC#, Commodity Name, etc). b
Page 1 Set auto code for the UPC# AUTO CODE 1 Is status of initial set #8-2? ENTER Set tare limit. 1 Max. 2 lb (US) Max. 1Kg/2.205 lb (CA/QR) ENTER 0 NEXT PLU or SET NEXT Enter PLU# (max. 6 dig.) Enter UPC# (Max. 6 dig.) ENTER Enter commodity name. (max. 32 chars.
PAGE 27
10. PROGRAMMING PROCEDURES 10.2 PLU DATA SETTING Pressing the ↓ key instead of the key returns to the preceding menu. Verification label of PLU data ENTER key advances to the next menu. Pressing the ↑ (W: Weigh, F: Fix, B: By-count) (C: Compulsory, Blank: Not compulsory) NOTES: 1. A UPC code is made up of a combination of an entered code and an AUTO CODE. Be sure to attach some characters to the end of the AUTO CODE, or all entered codes will be ignored and an AUTO CODE will become an UPC code (see ex.
PAGE 28
10. PROGRAMMING PROCEDURES 10.3 INGREDIENT MESSAGE 10.3 INGREDIENT MESSAGE Menu Page: 1 Item No.: 2 Ingredient messages can be printed on a label with a maximum of 54 characters per line using small letters or 32 characters per line using boldfaced small letters. Will print up to 38 lines. c
Page 1 Enter the PLU# (max. 6 dig.) 2 NEXT PLU ENTER or c Enter the ingredient message (Refer to Page 10-3.) ENTER Page 1 ESC.
PAGE 29
10. PROGRAMMING PROCEDURES 10.4 NUTRITION SETTING 10.4 NUTRITION SETTING Menu Page: 1 Item No.: 3 Using the following procedure, nutrition information and caloric intake can be set. Serving Size and Servings Per Container consist of a maximum of a 18 characters. However, total number of characters including title characters must not exceed 30. f
Page 1 d Enter the PLU# (max. 6 dig.) 3 NEXT PLU Enter the Serving Size. or ENTER Enter the Calories.
PAGE 30
10. PROGRAMMING PROCEDURES 10.4 NUTRITION SETTING A Additional Information Area 2 to 6. (0 to 99999 or 0.0 to 999.9) Enter the vitamin A. (0 to 999) Enter the Calcium. (0 to 999) ENTER ENTER Enter the Vitamin C. (0 to 999) Enter the Iron. (0 to 999) ENTER ENTER ENTER e Additional Information Area 7 to 12 (0 to 999) PROG.
Page 1 ESC. Main ENTER f Pressing the ↓ key instead of the ENTER key advances to the next menu. Pressing the ↑ key returns to the preceding menu. NOTES: 1.
PAGE 31
10. PROGRAMMING PROCEDURES 10.4 NUTRITION SETTING ● Set the Daily Value Table d AUTO CODE Enter the Basic Calories. (Content No. 1) Enter the Basic Saturated Fat. (Content No. 3) Enter the Basic Sodium. (Content No. 5) Enter the Basic Dietary Fiber. (Content No. 7) ENTER ENTER ENTER ENTER Enter the Basic Total Fat. (Content No. 2) Enter the Basic Cholesterol. (Content No. 4) Enter the Basic Total Carbohydrate. (Content No. 6) ENTER ENTER ENTER e NOTES: 1. DAILY VALUE (Max.
PAGE 32
10. PROGRAMMING PROCEDURES 10.4 NUTRITION SETTING ● Deleting Nutrition Data d DELETE PLU Enter the PLU# (max. 6 dig.) ENTER e ● Memory file sort The memory file is sorted when a memory full error occurs. d ◇ Y Sorting e Any key except Y Not Sorting Area for titles Area for entry data: Set in this menu (Nutrition Setting procedure) Area for data: Calculated on the basis of the entered data in Menu Page1/Item No.
PAGE 33
10. PROGRAMMING PROCEDURES 10.5 PLU VERIFYING LABEL 10.5 PLU VERIFYING LABEL Menu Page: 1 Item No.: 4 Verifies PLU data stored in the scale. g
Page 1 4 ENTER Set the entire PLU#. 1 0 0 The confirmation label is issued. Set the individual PLU#. (Ex. PLU #100) 1 ◇ ◇ Set the block PLU#. (Ex. PLU #100 to 199) 1 0 0 NEXT PLU 1 0 8 Set the zone PLU#. (Ex. PLU #100 to 108) CLEAR To interrupt label issue. ENTER To resume label issue which has been interrupted. PROG.
PAGE 34
10. PROGRAMMING PROCEDURES 10.6 ADDRESS AND COMMERCIAL MESSAGE SETTING 10.6 ADDRESS AND COMMERCIAL MESSAGE SETTING Menu Page: 1 Item No.: 5 A store address printed on label and a commercial message shown on the display can be set within the following character limits using the procedure below.
PAGE 35
10. PROGRAMMING PROCEDURES 10.7 COMBINATION MESSAGE 10.7 COMBINATION MESSAGE Menu Page: 1 Item No.: 6 You can combine some messages set in Section 10.6 together and create a maximum of 24 different combination messages. Message construction 8 n 7 n 6 n 5 n 4 n 3 n 2 n 1 n Message display time: Message display time ranges from 00 to 99 (seconds). When “00” is entered, no message will be displayed. 3rd message: 01 to 08: represents messeages No. 1 to 8 11 to 23: represents logo No.
PAGE 36
10. PROGRAMMING PROCEDURES 10.7 COMBINATION MESSAGE 3. Display method varies depending on message construction. 1) message combination a. single message ･･･････ either scrolling or fixed is available. b. multiple message ･･････ scrolled regardless of selection. 2) logo combination Logo must be a single logo and a fixed display. When logos are combined, no message will be displayed. 3) combination of message and logo It is prohibited.
PAGE 37
10. PROGRAMMING PROCEDURES 10.8 SPECIAL INFORMATION 10.8 SPECIAL INFORMATION Menu Page: 1 Item No.: 7 When the Net Weight Statement label is selected, 3 lines (32 characters/line) of special information can be printed in the label position where the net weight data is to be printed. The special information can be printed in the weigh and By Count mode. In the Fix mode, the net weight data is printed.
Page 1 7 ENTER Enter the special information. (Refer to page 10-3.) ENTER PROG.
PAGE 38
10. PROGRAMMING PROCEDURES 10.10 SPEED KEY SETTING 10.10 SPEED KEY SETTING Menu Page: 1 Item No.: 9 The SL-9000 has a maximum of 108×2 speed keys which are very convenient to call PLUs quickly. (Refer to page 5-3 regarding the Key Layout.) i
Page 1 Enter the Speed Key number (# 1 to 108 on each page) 9 ◇ NEXT PLU Toggles the speed key Page ENTER or i Enter the PLU#. (max. 6 dig.) ■ ENTER Page 1 ESC.
PAGE 39
10. PROGRAMMING PROCEDURES 10.11 PRINT FORMAT 10.11 PRINT FORMAT Menu Page: 2 Item No.: 0 The SL-9000 can memorize 5 different print formats. After print formats are set, you can call them by pressing the print format number.
Page 2 Select the print format # which allocates the label format # by the NEXT PLU key or key. 0 Enter the label format #. (Refer to table 2) j CHANGE PLU Issue method Batch On-demand FEED Select “SENSIBILITY ADJUST” by pressing the ◇ key.
PAGE 40
10. PROGRAMMING PROCEDURES 10.11 PRINT FORMAT ■ Table 2: Label Format Number Table Select the format # for the label to be used by referring to the table below. Print format Format # Basic form Commodity 57-mm wide label Length Nutri. 00 (50) NON POS 0 2 (48mm) lines only Yes 30.0 No No No --- --- --- 10 (60) POS 0 2 (48 mm) / 4 (57 mm) Yes 40.0 No No Yes 49.2 No No 11 (61) 6 2 (48 mm) / 4 (57 mm) Yes 54.8 No No Yes 63.
PAGE 41
10. PROGRAMMING PROCEDURES 10.12 DATE/TIME SETTING 10.12 DATE/TIME SETTING Menu Page: 2 Item No.: 1 Date, time, machine number, and store code are set with this procedure. k
Page 2 1 Set the date. (Month, Day, Year) ENTER Set the time. (Hour, Minute) ENTER k Set the machine No. (max. 6 dig.) ENTER Set the store No. (max. 5 dig.) ENTER PROG. Page 2 ESC. Main NOTES: 1. Express the time in a 24-hour military format. 2.
PAGE 42
10. PROGRAMMING PROCEDURES 10.13 CMT/PL-3 ■ PL-3 Operation Connect the PL-3 to the SL-9000 by using RS-232C Cable, then turn on the power of the SL-9000 and the PL-3. Insert a data disc into the PL-3 and adjust the transmission rate to the SL-9000 ( 7 2 :4800 BPS or 7 3 : 2400 BPS) by using the rotary switch. Press the SAVE key of the PL-3, then check whether the SAVE LED is on. Program the file number of the data disc by using the rotary switch. ( 4 1 : File No. 1, 4 2 : File No. 2, .......
PAGE 43
10. PROGRAMMING PROCEDURES 10.13 CMT/PL-3 ■ Table 4: ITEM # Transmission Item List CMT PL-3 2 VERIFY PLU & ING. = CMT 2 Title on the Display COMPARE PLU & ING. IN OLD FORMAT Contents of Transmission ○ ○ 3 READ PLU & ING. FM CMT 3 READ PLU & ING. IN OLD FORMAT ○ ○ 4 WRITE PLU TO CMT 4 SAVE PLU IN NEW FORMAT ○ ○ 5 VERIFY PLU = CMT 5 COMPARE PLU IN NEW FORMAT ○ ○ 6 READ PLU FROM CMT 6 READ PLU IN NEW FORMAT ○ ○ 7 WRITE ING. TO CMT 7 SAVE ING.
PAGE 44
10. PROGRAMMING PROCEDURES 10.14 IN-LINE/LOCAL 10.14 IN-LINE/LOCAL Menu Page: 2 Item No.: 3 When the SL-9000 is used as a satellite in an in-line system, the “ID #” and “Transmission delay time” can be set by the following procedure.
Page 2 TMCC ◇ 3 Set ID numbers (Range: 0 to 255) ENTER Select mode l The transmission delay time can be set when in-line system is selected for TMCC. (Refer to Table 5) OFF-line ENTER PROG. Page 2 ESC. Main l NOTES: 1.
PAGE 45
10. PROGRAMMING PROCEDURES 10.15 LON SYSTEM 10.15 LON SYSTEM Menu Page: 2 Item No.: 4 The SL-9000 scales which consists of a master, satellites, and a backup master are connected each other by the LON cable to transmit data such as PLU, ING., NUTRI, etc. ID# 1 is reserved for the master terminal. ID# 2 is reserved for the backup master terminal or satellite terminal. ID# 3 to 32 are for satellite terminals. Setting numbers other than the above results in an error.
PAGE 46
10. PROGRAMMING PROCEDURES 10.15 LON SYSTEM ■ Data Transmission The following data is down-line-loaded. Page 1: (0). All (PLU+ING+NUTRI) Page 2: (0). SPEED KEY (1). PLU (1). LOGO (2). ING. (2). VENDOR (3). NUTRITION (3). FREE FORMAT (4). U. PRICE (4). ADDRESS (SL-9000N only) (5). DATE/TIME (5). INITIAL (#0-19, SL-9000N only) (6). MESSAGE LINK (Message) (9). CHANGE PAGE (7). LOCK SCALE (Check the LON cable) (8). OPEN SCALE (Release the lock after checking the LON cable.) (9).
PAGE 47
10. PROGRAMMING PROCEDURES 10.16 BAR CODE FORMAT 10.16 BAR CODE FORMAT Menu Page: 2 Item No.: 6 With the SL-9000 scale, four kinds of bar code formats are available. These formats can be changed freely. Example) 2 Current format 9 C1 C2 C3 Flag Changed format 0 C4 C5 C6 P2 P3 UPC # 2 C2 C3 C4 Flag C5 P4 P5 Price C6 PC/D P1 P2 Total check digit P3 P4 Price check digit or weight check digit.
PAGE 48
10. PROGRAMMING PROCEDURES 10.16 BAR CODE FORMAT 2. When the ENTER key is pressed, bar code format is checked. An error occurs in the following cases. ① Check digit (C/D) is at other than digit-13. ② Price check digit (PC/D) cannot be calculated. (Price is other than 4 or 5 digits.) ③ Price is not set serially beginning from P1 (P1 to P4, or P1 to P5). ④ Weight is not set serially beginning from W1 (W1 to W5). 3.
PAGE 49
10. PROGRAMMING PROCEDURES 10.17 TITLES 10.17 TITLES Menu Page: 2 Item No.: 7 You can register and change displayed/printed titles of the additional information area for nutrition facts using the following procedure. Registered or changed titles are stored in the RAM. When ALL clear or RAM clear is executed, these titles will be cleared and the initial titles will resume. Before starting this operation, set the initial setting #7-3 to 1.
Page 2 7 Enter the title #. (See NOTE.) Enter the title.
PAGE 50
10. PROGRAMMING PROCEDURES 10.18 TRANSFERRING LOGO DATA 10.18 TRANSFERRING LOGO DATA Menu Page: 2 Item No.: 8 Logo data is created on a PC and stored into RAM through the CMT interface. Two different sizes of logos, 320x118 dots and 256x64 dots, are available on the SL-9000 series. 64 KB of RAM area is secured for logo data, in which the maximum of 13 logos (320x118 dots) or 26 logos (256x64 dots) can be stored. Before starting the following operation, set the initial setting #10-7 to 1.
PAGE 51
10. PROGRAMMING PROCEDURES 10.19 IDIOM SETTING ■ Table 6: Error message during data transmission Error message DATA ERROR Error position Cause Header text Data text Timeout ○ ○ Incorrect segment ○ ○ Incorrect logo size ○ Incorrect number of logos ○ Incorrect logo number ○ Incorrect number of dots to be printed. ○ Parity error ○ ○ Framing error ○ ○ ○ Overrun error 10.19 IDIOM SETTING Menu Page: 2 Item No.
PAGE 52
10. PROGRAMMING PROCEDURES 10.20 VENDOR SETTING 10.20 VENDOR SETTING Menu Page: 3 Item No.: 0 Up to 40 vendors can be registered using the following procedure. The vendor number must be set from 0 to 39 in order. One vendor name can contain a maximum of 12 characters. s
Page 3 0 Set a vendor number. (#0∼39) Enter a vendor name. (Max. 12 charas.) ENTER ENTER PROG. Page 3 ESC. Main s ● Deleting a vendor number Page 3 0 DELETE PLU Enter a vendor number.
PAGE 53
10. PROGRAMMING PROCEDURES 10.21 FREE FORMAT SETTING 10.21 FREE FORMAT SETTING Menu Page: 3 Item No.: 1 When using 57-mm wide labels, up to three print formats can be changed freely. Moreover, characters can be rotated and magnified, and print items are selectable. Enter the coordinate of each print item’s lower left corner using the lower left corner of a label as the origin. When a print item is located beyond the label width, an error will occur. Key functions ① ↓ : Moves downward (Data is stored.
PAGE 54
10. PROGRAMMING PROCEDURES 10.21 FREE FORMAT SETTING NOTES: 1. The following print items cannot be magnified. (1) LOGOs (2) Safe handling precautions (3) Ingredient messages (4) Barcode (5) FSP block (SL-9000N only) 2. Base label format numeric data is shown automatically. X coordinate: 0-383 dots (1 dot = 0.132 mm) Y coordinate: 0-1300 dots (1 dot = 0.154 mm) Format data beyond the effective print area results in an error. 3.
PAGE 55
10. PROGRAMMING PROCEDURES 10.21 FREE FORMAT SETTING No. 26 27 28 29 30 31 32 33 Print Item (F) Unit price (title) (F) Weight (F) Weight (title) (F) Price (F) Price (title) (L) LOGO FSP block (SL-9000N only) LOGO 2 (SL-9000N only) Print area size Normal Rotation X Y X Y 105 13 13 120 106 20 20 112 105 13 13 120 138 32 32 146 105 13 13 120 320 118 ---- ---384 184 ---- ---160 80 ---- ---- Note When setting the print item positions (X and Y), an error will occur in the following cases.
PAGE 56
10. PROGRAMMING PROCEDURES 10.21 FREE FORMAT SETTING 8. Print coordinate ∼ ∼ ∼ *1 Address Commodity *2 *1 Addresses are printed together with the previous label’s data. To print addresses, use normal labels. POS (Format #10-16): 10.0 mm NET (Format #21-26): 10.0 mm Bar code (Format #31-35): 8.
PAGE 57
11. PROGRAMMED DATA VERIFICATION REPORTS 11. PROGRAMMED DATA VERIFICATION REPORTS 11. PROGRAMMED DATA VERIFICATION REPORTS The programmed data can be printed on journal paper. Before issuing these reports, load the journal paper. The programmed data verification reports cannot be issued with any label. The keys to be used in the following procedures are those on the numeric key pad, which is right side of keyboard in the figure on page 5-3, but not on the programming keyboard.
PAGE 58
11. PROGRAMMED DATA VERIFICATION REPORTS 11. PROGRAMMED DATA VERIFICATION REPORTS Table 7 Menu # ● Report Name Contents 50 PLU programmed data report All the preset PLU data are listed in the PLU # order (from small to large #). 51 Commodity description report All the preset commodity names are listed in the PLU # order (from small to large #). 52 Speed key programmed data report The PLU # and the commodity name preset on each speed key is listed.
PAGE 59
12. PASSWORD SECURITY 12.1 SETTING PASSWORD AND PROTECT MENU 12. PASSWORD SECURITY You can protect all menus (except REG. menu) and set two step passwords for access to protected menus. 12.1 SETTING PASSWORD AND PROTECT MENU
0. PROG. 1. REG. 2. MARK DOWN 3. REWRAP 4. SECURITY 5. REPORT 6. RESET 7. 8. 9. ESC. 4 w ◇ Select menus to be protected.
PAGE 60
12. PASSWORD SECURITY 12.1 SETTING PASSWORD AND PROTECT MENU B 1 Enter password B in 4 digits. 2 3 4 PRT * Exclude menus to which password B cannot access. P M 2 R S X ○ × ○ ○ ー × ○: Valid ×: Invalid ー: Not need 6 Z PRT * w ESC. NOTES: 1. Select validity of the password by pressing the ◇ key 2. When the same password is entered for password A and B, password A has priority over the password B. 3.
PAGE 61
12. PASSWORD SECURITY 12.2 CALLING MENU BY ENTERING PASSWORD 12.2 CALLING MENU BY ENTERING PASSWORD ESC.
0. PROG. 1. REG. 2. MARK DOWN 3. REWRAP 4. SECURITY 5. REPORT 6. RESET 7. 8. 9. Enter a menu No. 0 to 6 Accessible with the password Accessible without the password 1 (REG.) 0 , 2 to 6 Not protect menu Protect menu C Enter the 4-digit Password. ESC.
PAGE 62
13. OPERATING PROCEDURES ■ NOTES BEFORE STARTING OPERATION 13. OPERATING PROCEDURES WARNING! Do not exceed the platter weight of maximum capacity. Or hang any item from the scale which exceed the platter weight. ■ NOTES BEFORE STARTING OPERATION (1) Turn the power ON. (2) A sixteen-second scanning will be performed after pressing the POWER key. (3) Should a power failure occur during operation, remove the commodity from the platter and insert the power plug into an AC outlet again when power is restored.
PAGE 63
13. OPERATING PROCEDURES 13.1 WEIGHING OPERATION 13.1 WEIGHING OPERATION Menu: REG., M.DOWN, or REWRAP Mode: WEIGH The weigh mode is used to weigh a commodity and to issue the label. The label contains data such as a weight, unit price (price per weight) and total price (calculated as a result of the weighing operation). The following is a basic operation seen at the sales floor of a store or at a back room where different kinds and weights of commodities are repacked.
PAGE 64
13. OPERATING PROCEDURES 13.2 FIX PRICE OPERATION (FOR US TYPE ONLY) 13.2 FIX PRICE OPERATION (FOR US TYPE ONLY) The FIX mode (Fix Price Mode) is used to issue a label for a commodity of a fixed price PLU (i.e. the price determined by the store), the weight of which may vary from commodity to commodity. In this mode, the Unit Price of the commodity looked up from the PLU file will be printed as the Total Price regardless of its actual weight, and the weight is also printed on the label. Menu: REG., M.
PAGE 65
13. OPERATING PROCEDURES 13.3 BY COUNT OPERATION 13.3 BY COUNT OPERATION The BY-COUNT mode is used to issue the label of commodities of the same kind in a package (or may not be packed). The whole package quantity (or a certain quantity) and the whole package price (or the price per the quantity) are usually preset. Thus, it is not necessary to weigh the commodities by the scale in such cases. Menu: REG., M.DOWN, or REWRAP Mode: BY-COUNT Example) In case of sell 10 DONUTS at the price of $1.
PAGE 66
13. OPERATING PROCEDURES 13.3 BY COUNT OPERATION Example) An open price item can be sold as below: ① 1 piece at 15 dollars ② 15 pieces at 10 dollars ③ 15 pieces sold at 0.5 dollars per 10 pieces Enter the PLU #. 5 Press: 1 PLU ex.) ① Enter quantity Press: 1 5 Enter price FOR ex.) ② ex.
PAGE 67
13. OPERATING PROCEDURES 13.4 PRINT COUNT OPERATION 13.4 PRINT COUNT OPERATION With this procedure, a specified number of the same labels can be issued. Menu: REG., M.DOWN, or REWRAP Mode: WEIGH, FIX or BY-COUNT Example A) When operating in Weigh mode. Press : Set the number of labels. (Max. 99 labels) PRESET COUNT 5 0 PRT * Press : 3 Enter the PLU #. 0 9 1 © PLU Press : Remove the commodity. SAVE PLU data is saved. Place a commodity on the platter. (Ex. 0.700 lb.
PAGE 68
13. OPERATING PROCEDURES 13.4 PRINT COUNT OPERATION Example B) When operating in Fix or By Count mode. PRESET Press : COUNT Set the number of labels. (Max. 99) 2 5 PRT * Press : 1 Enter the PLU #. Press : 5 PLU PRT * [BY COUNT] Press, to save the PLU data : SAVE [FIX] SPLIT PRICE operation Batch Place a commodity on the platter. (Ex. 1.320 lb.) MANUAL : PRT * Batch The label is issued with the mount paper attached. Remove the commodity from the platter.
PAGE 69
13. OPERATING PROCEDURES 13.4 PRINT COUNT OPERATION Example C) When issuing only the nutrition information label. Note that nutrition information can be printed only on several types of label. Refer to Page 10-19. PRESET COUNT Select basic data and nutrition information labels or a nutrition information label by pressing this key. Set the number of labels. (Max. 99 labels) ◇ 9 9 PRT * Enter the PLU #. 3 9 PLU PRT * The nutrition information label is issued in the following methods.
PAGE 70
13. OPERATING PROCEDURES 13.5 ISSUING LABELS WITH NET WEIGHT STATEMENT (FOR US TYPE ONLY) 13.5 ISSUING LABELS WITH NET WEIGHT STATEMENT (FOR US TYPE ONLY) Menu: REG., M.DOWN, or REWRAP Mode: FIX When the initial settings #1-7 and #1-8 are set to 1, a Net Weight Statement is printed on the label. A unit price and a tare registered in each PLU are printed as a price and a net weight. Example) The preset price is $2.10 and the preset Net Weight is 12 oz.
PAGE 71
13. OPERATING PROCEDURES 13.5 ISSUING LABELS WITH NET WEIGHT STATEMENT (FOR US TYPE ONLY) NOTES: 1. To print NET WT. data, from the FIX mode, load a label which has an area to print a NET WT. Statement. 2. The quantity sold number and price data in NET WT. statement operation will be accumulated in the memory. No weight data will be accumulated. 3. The position of the decimal point is adjustable and a comma or period is selectable by the initial setting. 4. Weight data is shifted to the left. 5.
PAGE 72
13. OPERATING PROCEDURES 13.6 TARE/SAVE FUNCTION PROCEDURES 13.6 TARE/SAVE FUNCTION PROCEDURES Menu: REG., M.DOWN, or REWRAP Mode: WEIGH or FIX (Tare % function is available in WEIGH mode only.) There are two kinds of tare subtraction procedures, one is “Direct tare”, the other is “Preset tare ”The SAVE key is used to save the tare, unit price, and PLU data after taking a commodity from the platter. 2 0.200 lb 0 Tare % 0 Place a container on the platter. (Ex. 0.
PAGE 73
13. OPERATING PROCEDURES 13.7 CALLING AND PRINTING GRADE LINES 13.7 CALLING AND PRINTING GRADE LINES A grade line is a short message added to a commodity name. A grade line can be selected from maximum of 49 programmed grade lines and printed on the label. Menu: REG., M.DOWN, or REWRAP Mode: WEIGH or FIX, or BY COUNT Enter the PLU #. 3 1 Press: PLU Press: G.LINE MANU. BY-COUNT DONUTS ← Commodity Name PREMIUNS OFFERED ← Grade Line PCS Enter the G.LINE #. (1 to 49) UNIT/$ 10 4/1.
PAGE 74
13. OPERATING PROCEDURES 13.8 CALLING AND PRINTING LOGOS 13.8 CALLING AND PRINTING LOGOS When the initial set #10-7 is set to “1” (or “2”: SL-9000N only), a logo containing a picture, a mark, a POP message, etc., can be printed on the ingredient label having 12 lines or more. Logo data is created on the PC and stored into the memory through the CMT/PL-3 interface. Menu: REG., M.DOWN, or REWRAP Mode: WEIGH, FIX, or BY COUNT LOGO Press: ◇ Select the LOGO type (LOGO(1) ↔ LOGO(2) ↔ F.
PAGE 75
13. OPERATING PROCEDURES 13.9 SELECTING PRINT ITEM 13.9 SELECTING PRINT ITEM Menu: REG, M.DOWN, or REWRAP Mode: WEIGH, FIX, or BY COUNT Press: PROG. NEXT or VOID PLU Select an item. (Refer to Table. 9) 1 1 to Print ←→ No print 1:Print 0:Non print 1 2 ◇ 0 2 7 ◇ Idle time till the Auto message is displayed.
PAGE 76
13. OPERATING PROCEDURES 13.9 SELECTING PRINT ITEM NOTES: 1. A store code can be printed in place of a ‘packed on date’ and ‘sell by date’ by changing the initial settings #6-5 and #6-6. To print a store code, select ‘packed on date’ or ‘sell by date’ as a print item using the above procedure. 2. The print of “packed on time” with alphabetical code can be selected with the Initial setting #6-6. (SL-9000N only) 3. Setting data will not be changed by turning the power off, changing the mode or calling a PLU.
PAGE 77
13. OPERATING PROCEDURES 13.11 BATCH PRINT MODE (with 30 Items Run Assignment) 13.11 BATCH PRINT MODE (with 30 Items Run Assignment) Menu: REG., M.DOWN, or REWRAP Mode: FIX, or BY COUNT Up to 99 labels per PLU can be issued in non-scale mode. Up to 30 items can be preset. (However, 0 is preset, issuing will be canceled.) Item# (1 to 30) PLU# Preset number of labels 1 Enter the PLU #. MANU.
PAGE 78
13. OPERATING PROCEDURES 13.11 BATCH PRINT MODE (with 30 Items Run Assignment) ● Unit Price Change and G.Line/LOGO Call x Enter the quantity. Call the Grade Line. Enter the required Grade Line# (1 to 49). 3 0 GRADE LINE 1 2 Press: PRT * Call PLU designation LOGO. (*1) LOGO Enter the required LOGO# (1 to 26). ◇ Select the LOGO type (LOGO (1) ↔ LOGO (2) ↔ F.Shopper) SL-9000N only Press: 1 0 PRT * y *1 By calling the PLU designation LOGO, the LOGO can be designated per PLU and printed.
PAGE 79
13. OPERATING PROCEDURES 13.11 BATCH PRINT MODE (with 30 Items Run Assignment) ● Label Issue Stop or Cancel z Clear an error or stop label issuing. C Cancel output VOID Press: PRT * Stop issuing the labels and cancel PLUs which have not been output. C A Completed NOTES: 1. When the label for NET.WT statement is not selected, pressing the PRESET COUNT key in FIX mode results in an error. 2. Programmed items are reset when: ① the power is off. ② changing the menu. (PROG./REG) ③ changing the mode.
PAGE 80
13. OPERATING PROCEDURES 13.12 VISUAL COMMODITY LIBRARY 13.12 VISUAL COMMODITY LIBRARY Menu: REG., M.DOWN, or REWRAP Mode: WEIGH, FIX, or BY COUNT In the following procedure, entering a group # (the upper two digits of PLU#) allows you to call 6 commodities which belong to the group. This function is convenient when calling a commodity which PLU# you do not know. Enter a group #.
PAGE 81
13. OPERATING PROCEDURES 13.13 FLOATING VENDOR 13.13 FLOATING VENDOR Menu: REG Mode: WEIGH, FIX, or BY COUNT Floating vendor function allows you to register different commodities sales together. This function is available when the Initial Setting #11-1 is set to 1 and using a receipt. Be sure to select IN-LINE in Section 10.15 LON SYSTEM even if no scale is connected, then enter the ID# 1, turn the power off and then on.
PAGE 82
13. OPERATING PROCEDURES 13.13 FLOATING VENDOR ■ Price deletion Prices already registered can be deleted in the following procedure. Enter vendor #. Enter the deletion mode. VOID NEXT PLU: the next item VOID: the previous item Delete a registered price. Exit the deletion mode. ■ NEXT or PLU VOID PRT * C Subtotal The following procedure will sum up all of the registered items. Enter vendor #. Press: ST Enter prices. C Press: PRT * A receipt will be issued.
PAGE 83
14. TOTAL OPERATION 14. TOTAL OPERATION 14. TOTAL OPERATION In Report or Reset mode you can issue a sales report or reset report with either a label or journal paper. Menu: REPORT or RESET REPORT The totals will not be cleared as they are printed on labels or journal paper. RESET The totals will be cleared as they are printed on labels or journal paper. ESC. 5 or 6 ◇ Issue each Report ESC. Label Ö Journal (Refer to the following pages.) No.
PAGE 84
14. TOTAL OPERATION 14.1 HOURLY TOTAL REPORT 14.1 HOURLY TOTAL REPORT Ex.) REPORT Menu PRT * 0 NOTES: 1. When issuing an hourly report, hours with no sales are not printed. 2. An hourly report is printed as follows: 1) Label: Issued sequentially in on-demand mode. 2) Journal paper: Issued with journal paper. 3) Label with backing paper: Issued sequentially in batch mode. 3. If the C key is pressed during issuance, the hourly report being printed will complete, then the total report will be issued.
PAGE 85
14. TOTAL OPERATION 14.4 VENDOR TOTAL REPORT A Individual Total Ex.) Individual PLU Total (PLU #100) 1 B 0 PRT * 0 Block Total Ex.) UPC Block Total (UPC #100100 to 100199) 1 0 0 ◇ 1 PRT * ◇ NOTE: The ◇ key represents 0 through 9. The most significant digit in the starting number is followed by an appropriate number of ◇ keys. C Zone Total Ex.) PLU Zone Total (PLU #100 to 107) 1 D 0 0 PLU 1 0 7 PRT * Entire PLU Total PRT * NOTES: 1.
PAGE 86
15. ERROR MESSAGE TABLE 15. ERROR MESSAGE TABLE 15. ERROR MESSAGE TABLE Take the following action if an error message has appeared on the commodity name display along with the buzzer sounding. WARNING: If you cannot solve the problem with the following solution instruction, do not attempt further trouble shooting, by yourself. Turn the power off, unplug the printer, then contact your Authorized Service representative for assistance.
PAGE 87
15. ERROR MESSAGE TABLE 15. ERROR MESSAGE TABLE ● Label lssue Mode Message ● Cause Solution DATA ENTRY ERROR Error in key input. Press the C key, and re-input the right data. PLU NOT FOUND The PLU # being called out is not registered. Press the C key, and check the PLU #. TOTALS OVERFLOW GRAND TOTAL or PLU TOTAL Press the C key, then the ESC. key and memory has been exceeded at select ‘RESET’. Then sum up the the time of issuing a label. exceeded memory.
PAGE 88
15. ERROR MESSAGE TABLE 15. ERROR MESSAGE TABLE ● CMT Operation Mode Message Cause Solution Mismatch of the model type. Mismatch of the base unit. MISMATCH SCALE SPEC Mismatch of the VERSION. Press the CLEAR key Mismatch of the TRANSMITTING DATA. Mismatch of the scale capacity. Parity error Framing error BAD TAPE OR CMT Press the CLEAR key Overrun error Data error Two or More Hardware error TIME OUT ERROR ● Time out error Press the CLEAR key.
PAGE 89
16. CLEANING THE PRIT HEAD 16. CLEANING THE PRINT HEAD 16. CLEANING THE PRINT HEAD WARNING! Care must be taken not to injure your fingers with the label cutter during installing, removing or cleaning it. If the print head is dirty, printing will not be clear. The print head should be cleared with a print head cleaner everyday before use, according to the following procedure: 1. Open the printer cover and turn the head-up lever to the anticlock wise. (See page 8-1) 2.
PAGE 90
17. TROUBLESHOOTING 17. TROUBLESHOOTING 17. TROUBLESHOOTING Problems Solution “- - - - -” is displayed at ● Was the power turned ON when something was on the platter? power on. → Make sure nothing is on the platter and turn the power on again. ● Is the platter mounted correctly? → Mount the platter correctly and turn the power on again. Display unstable. Is anything touching the platter? → If so, remove it. ● Is the machine in a windy location? → Avoid locations subject to the wind. No print. 1.
PAGE 91
PAGE 92
E PRINTED IN SINGAPORE EM1-31076E