+00EH99677601_01EN_remo_IM.
+00EH99677601_01EN_remo_IM.book Page 1 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit Thank you very much for purchasing TOSHIBA/Carrier Remote Controller for Air Conditioner. Please read the owner's manual carefully before using your Remote Controller for Air Conditioner. • Be sure to obtain the “Owner’s manual” and “Installation manual” from constructor (or dealer).
+00EH99677601_01EN_remo_IM.book Page 2 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 1 ACCESSORY PARTS No. Parts Quantity 1 Signal receiving unit (provided 7.9” (200 mm) power cable) 1 2 Mounting bracket 1 3 Screws ∅0.16” x 1.0” (M4 x 25 mm) 2 4 Screws ∅0.16” x 1.6” (M4 x 40 mm) 2 5 Wood screws 2 6 Spacer 4 7 Wire joints 2 8 Cable tie 1 9 Pattern template 3.
+00EH99677601_01EN_remo_IM.book Page 3 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 2 SWITCH LOCATION OF SIGNAL RECEIVING UNIT Signal receiving unit 1 2 3 4 5 6 Screw Remove Face plate Remove the face plate from Signal receiving unit. Address selector switch This switch is used to address one of a maximum of six air conditioners that can be controlled by the remote controller. (Refer to page 11.
+00EH99677601_01EN_remo_IM.book Page 4 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 3 INSTALLATION LOCATION OF SIGNAL RECEIVING UNIT • Do not install in a location where the air contains oil mist, such as in a kitchen or factory. • Do not install next to a window, or in any other location directly exposed to sunlight and outside air.
+00EH99677601_01EN_remo_IM.book Page 5 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 4 HOW TO INSTALL THE SIGNAL RECEIVING UNIT NOTE • To avoid malfunction of the remote controller, do not assemble or run remote control wiring together with the power cables, and do not enclose them in the same metal conduit. • When the power unit induces electrical noise, it is recommended that a noise filter or the like be installed.
+00EH99677601_01EN_remo_IM.book Page 6 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 2. In order to later pass the Signal receiving unit wiring out through the upper case (thin part at the top center), use nippers or a similar tool to cut a notch in the same size as the Signal receiving unit cord (optional). (Fig. B) Notch where Signal receiving unit cord passes through top case 0.08”-0.
+00EH99677601_01EN_remo_IM.book Page 7 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 4. Use bracket parts (A) and (B) to securely grip the ceiling material. (Fig. E) Part (A) 5. Connect the Signal receiving unit wire (2-core) to the wire from the indoor unit. (Refer to “Wiring the Signal receiving unit.”) Check the terminal number on the indoor unit before wiring the Signal receiving unit and be sure not to wire incorrectly.
+00EH99677601_01EN_remo_IM.book Page 8 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 5 HOW TO PERFORM CABLING OF THE SIGNAL RECEIVING UNIT Flush Mounting Connection diagram Indoor unit remote controller terminal board Signal receiving unit Power wire from Signal receiving unit Wire of Signal receiving unit (Field procurement) (AWG20 (0.5 mm2)) (UL wires rated 300 V) Connector Provided wire joint (WHT 2) 1. Strip the insulation to approximately 0.
+00EH99677601_01EN_remo_IM.book Page 9 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 6 REQUIREMENT The control by two remote controllers is enabled by installing the wireless remote controller with the wired remote controller for an indoor unit. (Max. 2 remote controllers of wireless or wired are insatiable.) “2-remote controllers” controlling means that one or multiple units are operated by the multiple remote controllers. NOTE 1.
+00EH99677601_01EN_remo_IM.book Page 10 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit To operate a group control of multiple indoor units by 2 remote controllers MAIN and SUB remote controllers are operable even if they are installed to any indoor unit. (Total cable length: Within 656’2” (200 m)) Wireless remote controller kit Signal receiving unit Terminal block for remote controller cable Indoor unit No.
+00EH99677601_01EN_remo_IM.book Page 11 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 8 HOW TO SET THE ADDRESS SWITCH • When the multiple Signal receiving units are installed in the same room, an address can be set to prevent cross communication.
+00EH99677601_01EN_remo_IM.book Page 12 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 10 SELF-DIAGNOSIS TABLE AND MEASURES Lamp indication of Signal receiving unit : Goes off : Blink (0.5-sec. interval) Lamp indication No indication even if the remote controller is operated. Cause Power supply is not turned on. Miscabling between Signal receiving unit and indoor unit Measures Check cable connection and correct it.
+00EH99677601_01EN_remo_IM.book Page 13 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 12 EXPLANATION TO CUSTOMERS • Hand over the “Owner’s Manual” and “Installation Manuals” to the customer after installation works. • Explain usage and maintenance of the remote controller according to “Owner’s Manual”. 13 HOW TO HANDLE THE REMOTE CONTROLLER In case using remote controller mounting to the wall, etc.
+00EH99677601_01EN_remo_IM.book Page 14 Thursday, October 8, 2009 4:12 PM Installation Manual Wireless remote controller kit 14 TEST RUN Before test run • Before turning on the power supply switch, carry out the following procedure. 1 Using 500V-megger, check 1MΩ or more exists between the terminal block 1 to 3 and the earth. If 1MΩ or less is detected, do not run the unit. Do not apply to the remote controller circuit. 2 Check the valve of the outdoor unit being opened fully.
+00EH99677601_01EN_remo_IM.