® Satellite M20 Series Resource Guide Keep this guide in a convenient place to access important information about your computer.
Contents Regulatory information ....................................................................... 3 Introduction ...................................................................................... 22 Setting up your computer and getting started................................... 23 Your computer’s TFT display ............................................................. 28 Inserting and removing PC Cards ..................................................... 28 Learning the basics................
Regulatory information 3 Regulatory information Model: Satellite ® P25 Series ReWritable CD/DVD Drives The computer system you purchased may include a ReWritable CD and/or DVD drive(s), among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage.
Regulatory information PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory information 5 Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. FCC Requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems. Installation When you are ready to install or use the modem, call your local telephone company and give them the following information: ❖ The telephone number of the line to which you will connect the modem. ❖ The FCC registration number of the modem.
Regulatory information Disconnection If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Regulatory information 3 7 NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Regulatory information co-located with any other transmitter that has not been tested with this device. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Regulatory information 9 L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 MHz). Dans le cas d’une utilisation privée, a l’extérieur d’un bâtiment, audessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprés de I’IBPT est requise. Pour une utilisation publique à I’extérieur de bâtiments, une licence de I’IBPT est requise.
Regulatory information Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. Caution: Exposure to Radio Frequency Radiation The Toshiba Wireless LAN Mini PCI Card will be installed with one of two types of antennas.
Regulatory information Article 17 11 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.
Regulatory information Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916 Fax: 03-5444-9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
Regulatory information 13 The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The following information is dependant on what type of wireless device is in your computer. Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless network adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Regulatory information Approved Countries/Regions for use for the Intel® PRO/Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Regulatory information 15 Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ ❖ Bluetooth Specification Ver.1.1, as defined and approved by The Bluetooth Special Interest Group. Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Regulatory information Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Regulatory information 17 Caution: FCC Interference Statement This device complies with part15 of the FCC rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference, and ❖ This device must accept any interference received, including interference that may cause undesired operation. Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.
Regulatory information The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery. Using this equipment in Japan In Japan, the frequency bandwidth of 2,400-2,483.
Regulatory information 19 Device Authorization This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan. The Name of the radio equipment: EYXF2CS TELECOM ENGINEERING CENTER Approval Number: 01NYDA1305 The following restrictions apply: ❖ ❖ Do not disassemble or modify the device. Do not install the embedded wireless module into other device.
Regulatory information Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. ©2003 by Toshiba America Information Systems, Inc. All rights reserved.
Regulatory information 21 trademark of the Wireless Capability Ethernet Alliance. Bluetooth is a trademark owned by its proprietor and used by Toshiba under license. TouchPad and cPad are trademarks of Synaptics, Inc. Sound Blaster is a registered trademark of Creative Labs, Inc. Intel and Pentium are registered trademarks of the Intel Corporation. PS/2 is a registered trademark of IBM, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies.
Introduction Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. You will find that the Windows® XP operating system is already installed on your computer. It offers exciting features and easy Internet access. This guide This guide offers important information about your computer, including solutions to the most common problems, in addition to features and specifications.
Setting up your computer and getting started 23 Other icons used Additional icons highlight other helpful or educational information: HINT: This icon denotes helpful hints and tips. Other documentation Your computer comes with all or some of the following documentation in addition to this resource guide: ❖ An electronic version of the user’s guide. Look for the user’s guide icon on your desktop or in the DOCS folder on the C: drive.
Setting up your computer and getting started ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching. ❖ If you are using an external monitor, the top of the display should be no higher than eye level. ❖ If you use a paper holder, set it at about the same height and distance as the screen.
Setting up your computer and getting started 25 When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be the last step; otherwise, the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Setting up your computer and getting started Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data. Additional memory comes in various sized modules. You can install a maximum of two modules in your computer’s expansion memory slots, located on the bottom of your computer. You need a standard Phillips no. 1 screwdriver to install a memory module.
Setting up your computer and getting started 27 Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer. 6 Remove the new memory module from its antistatic packaging. 7 Insert the memory module in the slot and gently press it down into place.
Your computer’s TFT display Pulling the clips away from the memory module 3 Carefully remove the module from the slot. 4 Replace the cover plate and screws. 5 Turn the computer over and restart it. Your computer’s TFT display Small bright dots may appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology.
Inserting and removing PC Cards 29 ❖ Insert the PC card while the computer is running. Follow the steps below. ❖ Hot swap the card (choose this method if there is already a PC Card in the slot you wish to use). Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the PC Card is stopped, it is safe to remove it. Follow the steps below. 1 Locate the PC Card slots on the left side of the computer.
Learning the basics 2 Locate the PC Card ejection button that corresponds to the slot in which your PC Card is installed. The top tab releases a card in the upper slot. The bottom tab releases a card in the lower slot. 3 Press the PC Card eject button once to extend it, and push it again to remove the PC Card. Press the PC card ejection button once to extend it The PC Card ejects slightly from the slot. 4 Grasp the edges of the PC Card and pull it out of the slot.
Learning the basics ❖ 31 Never turn off the computer if a drive indicator light indicates a drive is active. The Windows® XP operating system records information, such as your desktop setup, during its shutdown procedure. If you do not let the operating system shut down normally, details such as new icon positions may be lost. Using the AccuPoint II® pointing device The button in the middle of the keyboard is the AccuPoint II pointing device.
Playing a CD or DVD right mouse button. For more information on programming buttons and keys, see “Fn-esse” in the electronic user’s guide. The small left button performs the Internet Back button. The small right button performs the Universal scroll. Playing a CD or DVD Your Satellite M20 Series computer may have a DVD-ROM, or Multifunction drive. Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform.
Playing a CD or DVD 33 Manual eject hole—Use if you need to release the disc tray when the power is off. Use a straightened paper clip or other narrow object to press the manual eject button located inside the hole. Never use a pencil to press the eject button. Pencil lead can break off inside the computer and damage it. Inserting compact discs To insert a compact disc into the DVD-ROM or Multifunction drive: 1 Make sure the computer is turned on. 2 Make sure the in-use indicator light is off.
Playing a CD or DVD Positioning the disc in the drive 7 Gently press the disc onto the center spindle until you feel it click into place. Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data. 8 Make sure the disc is completely on the spindle and is lying flat on the tray. If you insert the disc incorrectly, it may jam the drive.
Moving the computer 35 To remove a compact disc with the computer turned off: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. 2 Gently pull the tray out until it is fully open, remove the disc, and place it in its protective cover. 3 Gently push the tray in to close it.
Mobile computing Slim SelectBay, or carry additional charged battery packs with you. The computer also has an internal real-time-clock (RTC) battery. The RTC battery powers the RTC memory that stores your system configuration settings and the current time and date information. The RTC battery does not charge while the computer is turned off, even when AC power is attached.
Mobile computing 37 When handling a battery, be careful not to drop it or short-circuit its terminals. To change the battery: 1 Save your work. 2 Shut down and turn off the computer. 3 Remove all cables connected to the computer. 4 Turn the computer over. 5 If the battery lock is in the locked position (towards the center of the computer), slide it towards the edge of the computer to unlock it. 6 Slide the battery release latch to release the battery.
Mobile computing The battery pack has been designed so that you cannot install it with reverse polarity. If the battery does not slide into the slot easily, move the battery release lock to the unlocked position and try again. Do not force the battery into position. 9 Reset the battery lock to the locked position. 10 Turn the computer right side up. 11 Reconnect any cables. 12 Restart the computer.
Mobile computing 39 ❖ When you install the battery pack, you should hear a click when it is seated properly. ❖ Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 Turn off the computer’s power.
If something goes wrong ❖ Store spare battery packs in a cool dry place out of direct sunlight. If something goes wrong Problems that are easy to fix Your program stops responding. If you are working with a program that suddenly freezes all operations, chances are the program has stopped responding. You can exit the failed program without shutting down the operating system or closing other programs. To close a program that has stopped responding: 1 Press Ctrl, Alt, and Del simultaneously (once).
If something goes wrong 41 The Details button displays information that the software manufacturer needs to help you solve your problem. 2 Press Ctrl and C simultaneously to copy the text to the clipboard. 3 Open Notepad (click Start, point to All Programs, then point to Accessories and click Notepad). 4 Press Ctrl and V simultaneously to paste the details into Notepad. 5 Add a paragraph break and type some notes describing what you were doing when you received the message.
If something goes wrong If the problem occurs when both the keypad overlays are off, make sure the software you are using is not remapping the keyboard. Refer to the software’s documentation and check that the program does not assign different meanings to any of the keys. Display problems Here are some typical display problems and their solutions: The display is blank. Display Auto Off may be in effect. Press any key to activate the screen.
If you need further assistance 43 Resolving PC Card problems The slots appear dead and cards that worked no longer do. Check the PC Card status: 1 Click Start. 2 Click My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. 3 Click the Hardware tab. 4 Click the Device Manager button. 5 Double-click the PCMCIA adapter. 6 Double-click the appropriate PC Card.
If you need further assistance ❖ Review the troubleshooting information in your operating system documentation. ❖ If the problem occurs while you are running a program, consult the program’s documentation for troubleshooting suggestions. Contact the software company’s technical support group for their assistance. ❖ Consult the dealer from whom you purchased your computer and/or program. Your dealer is your best source for current information. Detailed system specifications are available at www.ts.
Power cable connectors Power cable connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada (UL and CSA approved) United Kingdom (BS approved) Australia (AS approved) Europe (VDA and NEMKO approved) Features and specifications This section lists the computer’s features.
Features and specifications - use of computer in areas with low air pressure (high altitude >1,000 meters or >3,280 feet above sea level) - use of computer at temperatures outside the range of 5°C to 35°C (41°F to 95° F) or >25°C (77°F) at high altitude (all temperature references are approximate). CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shut-down.
Features and specifications 47 Ports DC-IN Lets you connect the computer to AC power, using the AC adapter and power cable Headphone jack Use the 3.5 mm headphone jack to connect stereo headphones or other audio output devices. Connecting headphones or other devices to this jack automatically disables the internal speakers Microphone jack 3.
Features and specifications Pointing device AccuPoint® II pointing device provides the functionality of a mouse or other pointing device PC card slots Two stacked PC Card slots let you install two Type II and one Type III PC Cards Sound controller ADI AD1886, 16-bit stereo, Sound Blaster® Pro and FM synthesis support; built-in stereo speakers; full duplex sound, 64-channel wavetable music synthesis; DirectSound® Direct3D®Sound, DirectMusic® DVD-ROM/ CD-RW drive 24x CD-ROM, 8x DVD-ROM, 24x CD-R,
Index 49 Index A AC adapter 24 AC power light 24 AccuPoint II pointing device 31 adding memory 26 avoiding injury 23 B battery changing 36 installing 36 removing 37 unlocking 37 battery alarms 36 battery life, maximizing 39 battery power running on 35 battery safety 38 built-in features 45 button eject 32 internet 32 scroll 32 C CD playing 32 CD-ROMs using 32 changing main battery 36 comfort chair 24 compact disc positioning 34 removing 34 compact discs handling 34 inserting 33 computer moving 35 place
Index safety 22 indicator light drive in-use 32 installing main battery 36 PC Cards 28 interference statement 12 internal drives 48 internet button 32 K keyboard not working 41 unexpected characters 41 L lights AC power 24 M main battery changing 36 manual eject hole 33 memory adding 26 expansion slots 26 memory module installing 26 removing 27, 28 Microsoft Windows XP 22 mobile computing 35 moving the computer 35 O operating system 22 P PC Card checklist 42 inserting 28 problem solving 43 PC card
Index T tips on computing 30 Toshiba Accessories information 23 U using the AccuPoint II pointing device 31 W Web sites 44 Web sites 26 RG 5.375 x 8.375 ver 2.3.
C1810-2 RG 5.375 x 8.375 ver 2.3.