TOSHIBA Satellite A60 Portable Personal Computer User’s Manual
Copyright © 2004 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
FCC information Product Name : Satellite A60 Model number : PSA60 FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc.
EU Declaration of Conformity TOSHIBA declares, that the product: PSA60* conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ❑ The telephone number of the line to which you will connect the modem ❑ The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.
If problems arise If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible.
The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
❑ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
❑ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ❑ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Optical disc drive standards TOSHIBA Satellite A60 series computer is shipped with one of the following drives preinstalled : DVD-ROM, CD-RW/DVD-ROM, DVD-R/-RW , DVD+-R/+-RW or DVD Super Multi drive. The drive has one of the following labels : CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE1 KLASS 1 LASER APPARAT Before it is shipped, the Class 1 Laser is certified to meet the United States Chapter 21 Standards of the Department of Health and Human Services (DHHS 21 CFR).
DVD-ROM drive safety instructions ** means any letters or numbers. CAUTIONS:1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
DVD-R/-RW drive safety instructions CAUTIONS:1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Matsushita UJ-811BTJA-A Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: Manufactured by Panasonic Communications Co., LTD 1-62, 4-Chome,Minoshima, Hakata-ku, Fukuoka, JAPAN Pioneer DVR-K13TBA Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS,21 CFR SUBCHAPTER J.
CD-RW/DVD-ROM drive safety instructions CAUTIONS:1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Toshiba Samsung SD-R2512 Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: TOSHIBA SAMSUNG STORAGE TECHNOLOGY CORPORATION 580, HORIKAWA-CHO, SAIWAI-KU, KAWASAKI-SHI, KANAGAWA, 2120013,JAPAN .
DVD +-R/+-RW drive safety instructions CAUTIONS:1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
HLDS GWA-4040N Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS,21 CFR SUBCHAPTER J. MANUFACTURED: Hitachi-LG Data Storage, Inc. 20, YOIDO-DONG, YOUNGDUNGPO-GU, SEOUL, KOREA HLDS GCC-4243N Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS,21 CFR SUBCHAPTER J. MANUFACTURED: Hitachi-LG Data Storage, Inc.
DVD Super Multi drive safety instructions CAUTIONS:1. The drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
TEAC DV-W24E Location of the required label CERTIFICATION TISH PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE DATE OF MANUFACTURE MANUFACTURED: TEAC CORPORATION 3-7-3 NAKA-CHO, MUSASHINO-SHI, TOKYO, JAPAN
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface Manual contents .................................................................................. xx Conventions ........................................................................................ xxi Abbreviations ...................................................................................... xxi Icons ................................................................................................... xxi Keys ...........................................................
USB diskette drive ............................................................................ 2-11 Optical Media drive .......................................................................... 2-12 Region codes for DVD drive and media ............................................. 2-12 Writable discs ................................................................................... 2-12 CD-RW/DVD-ROM drive .................................................................. 2-13 DVD-R/-RW drive ...........
Writing CDs on CD-RW/DVD-ROM drive ............................................ 4-8 Important message(CD-RW/DVD-ROM drive) ...................................... 4-8 Before writing or rewiting ..................................................................... 4-9 When writing or rewiting .................................................................... 4-10 Disclaimer(CD-RW/DVD-RO drive) .................................................... 4-10 Writing CD/DVDs on DVD-R/-RW drive ......................
Cleaning the computer .................................................................... 4-32 Moving the computer ....................................................................... 4-33 Heat dispersal ................................................................................... 4-33 Chapter 5 The Keyboard Typewriter keys .................................................................................. 5-1 F1 … F12 function keys .................................................................
Windows utilites ................................................................................ 6-16 Hotkeys ............................................................................................ 6-16 Panel power off ................................................................................. 6-16 System Auto Off ............................................................................... 6-16 Chapter 7 HW Setup and Passwords HW Setup ........................................................
Password ............................................................................................ 9-7 Keyboard ............................................................................................ 9-7 LCD panel ........................................................................................... 9-8 Hard disk drive .................................................................................... 9-8 DVD-ROM drive ...........................................................................
Appendix F Wireless LAN ....................................................................................... F-1 Appendix G Power Cord and Connectors ............................................................ G-1 Appendix H Internal Modem Guide .......................................................................H-1 Appendix I Parts Numbers ....................................................................................
Preface Congratulations on your purchase of the TOSHIBA Satellite A60 series computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A60 series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impaired performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
User's Manual PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
INTRODUCTION User's Manual Software ◆ The following software is preinstalled: • Microsoft® Windows XP Home Edition, Professional • Modem driver • Display Drivers for Windows • TOSHIBA Utilities • Wireless LAN driver (Can be used only for Wireless LAN models) • Sound Driver for Windows • DVD Video Player • LAN Drivers • TOSHIBA Power Saver • TOSHIBA user's manual • TOSHIBA Console • TOSHIBA ConfigFree • TOSHIBA Touch and Launch • TOSHIBA Touch Pad and On/Off Utility • TOSHIBA PC Diagnostic Tool • TOSHIBA Z
Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Intel® Celeron® Processor up to 2.8 GHz Mobile Intel® Pentium® 4 Processor up to 3.06GHz or higher Mobile Intel® Pentium® 4 Processor with supporting Technology up to 3.
INTRODUCTION User's Manual Diskette drive DVD-ROM drive 3 1/2" 1.44-megabyte or 720-kilobyte connects to the USB port. (Windows® XP does not support 720-kilobyte diskettes.) Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12cm (4.72") or 8 cm (3.15") CDs or 12 cm (4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
Features Some models are equipped with a full-size DVD-R/-RW drive module that lets you record data to rewriteable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/ 12cm (4.72") DVDs without using an adaptor. It reads DVDROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 10 speed, DVD-R at up to 2 speed and DVD-RW at up to 1 speed. This drive supports the same formats as the DVDROM drive.
INTRODUCTION User's Manual • Enhanced CD(CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 DVD Super Multi drive Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm(4.72") or 8cm(3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
Features INTRODUCTION Keyboard Built-in 85 keys , compatible with IBM enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5. The Keyboard, for details. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low.
INTRODUCTION User's Manual Slots PC card 3 - IN - 1 Memory Card slot A PC card slot accommodates: One Type II Refer to Chapter 8, Optional Devices, for details This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use (SD card/MultiMediaCard/Memory Stick) flashmemory. (Provided with some models) NOTE: Memory Stick Pro is not supported on this system.
Special features Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object Software Operating System Windows®XP Professional or Home Edition is available. Refer to the preinstalled software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
INTRODUCTION User's Manual System automatic Standby/Hibernation This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System hibernation in the System standby and System item of the Basic Setup tab in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.
Utilities Turns on fan first, then if necessary lowers CPU processing speed. Battery optimized Lowers the CPU processing speed first, then if necessary turns on the fan. Hibernation Standby This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 3, Getting Started, for details.
INTRODUCTION User's Manual DVD Video Player TOSHIBA Zooming Utility The DVD Video Player is used to play DVD-Video. It has an on-screen interface and functions. Click Start, point to All Programs, point to InterVideo WinDVD 5, then click InterVideo WinDVD 5. This utility allows you to enlarge or reduce the icon size on the desktop or the application window.
Options Also TOSHIBA Touch and Launch provides the following functions by customizing the settings. • To open a file stored in a predefined folder. • To quickly launch your frequently used applications which have been registered. TOSHIBA Controls This utility lets you customize application button: you can assign applications or several actions to the application button(default setting is the Internet button).
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. DISPLAY LATCH INFRARED PORT Figure 2-1 Front of the computer with display closed Display latch This latch secures the LCD panel in its closed position. Slide the latch to open the display. Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 Kbps, 57.6 Kbps, 38.
User's Manual Left side Figure 2-2 shows the computer’s left side. THE GRAND TOUR PC CARD SLOT 3-IN-1 MEMORY CARD INDICATOR 3-IN-1 MEMORY CARD SLOT OPTICAL MEDIA DRIVE Figure 2-2 The left side of the computer 3-IN-1 Memory Card Indicator This LED glows green when the computer is accessing the SD card/MultiMediaCard/Memory Stick Slot. CAUTION: Keep foreign objects out of the 3-IN-1 Memory Card slot. A pin or similar object can damage the computer’s circuitry.
Right side Right side Figure 2-3 shows the computer’s right side. HARDDISK VOLUME CONTROL HEADPHONE JACK USB PORT THE GRAND TOUR WIRELESS COMMUNICATION SWITCH MICROPHONE JACK Figure 2-3 The right side of the computer Hard Disk Volume control Provides access to read and write. Use this dial to adjust the volume of the system speaker and headphones. Headphone jack A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output.
User's Manual THE GRAND TOUR Universal Serial Bus port The Universal Serial Bus (USB) port comply with USB2.0 standards, which enables data transfer speeds 40 times faster than the USB1.1 standards. (The port also support USB1.1.) CAUTION: Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. NOTE: Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly.
Back side TV OUT Modem jack 2. LAN jack Ether LAN active indicator (orange) Link indicator (green) Universal Serial Bus Port In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions. In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line.
User's Manual This Centronics-compatible, 25-pin parallel port is used to connect a parallel printer or other parallel device. This port supports Extended Capabilities Port (ECP) standard. i.LINK (IEEE1394) port Connect an external device, such as a digital video camera to this port for high-speed data transfer. Some models are equipped with a i.LINK port. THE GRAND TOUR Parallel port NOTE: When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified.
Front with the display open The battery pack powers the computer when the AC adaptor is not connected. The Battery section in Chapter 6, Power and Power-Up Modes, describes how to access the battery pack. Additional battery packs can be purchased from your TOSHIBA dealer to extend the computer’s battery operating time. Battery pack cover latch Memory module cover Slide this latch to release or the battery pack. This latch moves only when the computer is upside down.
User's Manual THE GRAND TOUR Display screen The full-color LCD displays high-contrast text and graphics The computer's LCD consist of one of below:14.1" XGA, LCD consists of up to 1024 × 768 pixels or dots.15.0" XGA, LCD consists of up to 1024 × 768 pixels or dots. The computer has a Thin-Film Transistor (TFT) display. Refer to Appendix B. When the computer operates on power through the AC adaptor, the display screen’s image will be somewhat brighter than when it operates on battery power.
System indicators System indicators Figure 2-7 shows the system indicators, which light when various computer operations are in progress. THE GRAND TOUR DC IN POWER WIRELESS MAIN BATTERY DISK COMMUNICATION Figure 2-7 System indicators Power source/system indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
User's Manual The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you enter numbers. When the F11 key indicator glows the keypad overlay lets you control the cursor. THE GRAND TOUR NUMERIC MODE ARROW MODE Figure 2-8 Keypad overlay indicators Arrow mode Numeric mode When the Arrow mode indicator lights green, you can use the keypad overlay (white labeled keys) as cursor keys.
USB diskette drive Keyboard indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. DISK-IN-USE INDICATOR DISKETTE SLOT EJECT BUTTON Figure 2-10 USB diskette drive Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert diskette in this slot.
User's Manual Optical Media drive THE GRAND TOUR One of the following optical media drives is installed in the computer: CD-RW/ DVD-ROM drive, DVD-ROM drive, DVD-R/-RW drive, DVD +-R/+-RW drive, DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.
Optical Media drive DVDs ◆ DVD-R, DVD+R discs can be written only once. The recorded data cannot be erased or changed. ◆ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
User's Manual DVD-R/-RW drive The full- size DVD-R/-RW drive module lets you record data to rewritable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. THE GRAND TOUR NOTE: The read speed is slower at the center of a disc and faster at the outer edge.
AC adaptor DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to s as rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. DVD read 8 speed (maximum) DVD-R write 4 speed(maximum) DVD-RW write 2 speed(maximum) DVD+R write 2.4 speed(maximum) DVD+RW write 2.
User's Manual CAUTION: Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The output rating for the computer is 19 volts DC. THE GRAND TOUR CAUTION: Please use only the AC Adapter supplied with the computer or an AC Adapter certified by TOSHIBA.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User's Manual Setting up your work space GETTING STARTED Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Setting up your work space ❑ Set the computer on a flat surface at a comfortable height and distance. The display should be no higher than eye level to avoid eye strain. ❑ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ❑ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility.
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright light that could shine directly in your eyes. ❑ If possible, use soft, indirect lighting in your computer work area.
Connecting the AC adaptor Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
User's Manual 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. NOTE: When you open the display, hold it with both hands and lift up slowly.
Starting up for the first time Figure 3-5 Turning on the power GETTING STARTED Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows®XP Professional or Windows®XP Home Edition Start-up Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode.
User's Manual 3. If you are using Windows®XP Pro/ XP Home Edition click start then click Turn off computer. From the Turn off computer menu select Turn off. 4. Turn off the power to any peripheral devices. Caution: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off.
Starting up for the first time Starting Hibernation To enter Hibernation mode, follow the steps below. 1. Click Start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. Hibernate is not displayed. 4. Press the Shift key. The Standby item will change to Hibernate. 5. Select Hibernate. Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below.
User's Manual Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. CAUTIONS: 1. When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. 2. To restore operation from Standby mode, press the power button or press any key.
Starting up for the first time ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ❑ You can use the panel power off feature. Executing standby NOTE: You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled.
User's Manual Restarting the computer Certain conditions require that you reset the system. For example, if: ❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard commands. ❑ There are three ways to reset the computer system: 1. Click start then click Turn off computer. From the Turn off computer menu select Restart. 2. Press Ctrl + Alt + Del to display the windows task manager, then select Shutdown and Restart. GETTING STARTED 3.
Chapter 4 Operating Basics This chapter gives information on basic operations including using , USB diskette drive, optical media drives, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Using the Touch Pad To use the Touch Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go. Two buttons below the Touch Pad are used like the buttons on a mouse pointer .
User’s manual Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour, for more information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-1. OPERATING BASICS NOTE: Make sure the connector is right side up and properly aligned with the socket.
Using optical media drives Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it : 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Open the Safety Remove Hardware icon on the system tray. 3. Click Diskette drive. 4.
User’s manual Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-2 to 4-6. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Figure 4-2 Pressing the DVD-ROM eject button OPERATING BASICS b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 1.
Using optical media drives 2. Grasp the drawer gently and pull until it is fully opened. Figure 4-4 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer.
User’s manual NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-5. CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Do not keep foreign matter from entering the drive.
Using optical media drives Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-7. CAUTION: Do not press the eject button while the computer is accessing the DVD-ROM drive. Wait for the optical media drive indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened. CAUTIONS: 1.
User’s manual Audio/Video controls This section describes how to use the audio/video control buttons. Next and Previous buttons A single button on a rocker controls the Next and Previous functions. Press on the icon to select the desired function. Next Previous Press the or data. Press the data. icon to advances to the next track, chapter icon to advances to the previous track, chapter or NOTE: If Random is selected in Windows Media Player, selecting Next or Previous advances to a random selection.
Writing CDs on CD-RW/DVD-ROM drive If you fail to do so, the CD-RW/DVD-ROM drive may not function properly, and you may fail to write or rewrite,lose data or incur other damage. Before writing or rewriting Please observe the following points when you write or rewrite the data. ◆ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: CD-RW: TAIYOYUDENCO.,LTD. Mitsui Chemicals Inc. MITSUBISHICHEMICALCORPORATION RICOH Co., Ltd.
User’s manual When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ◆ Always copy data from the HDD to the CD. Do not use cut-and-paste.The original data will be lost if there is a write error. ◆ Do not perform any of the following actions: ◆ Change users in the Windows XP operating system. ◆ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. ◆ Start a communication application such as a modem.
Writing CD/DVDs on DVD-R/-RW drive Writing CD/DVDs on DVD-R/-RW drive You can use the DVD-R/-RW drive to write data to eitherDVD-R/-RW discs. The following applications for writing are supplied on CD-ROM. InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc. Important message (DVD-R/-RW drive) Before you write or rewrite to DVD-R/-RW disc, read and follow all setup and operating instructions in this section.
User’s manual ◆ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW discs. ◆ Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. ◆ Data deleted (erased) from a CD-RW and DVD-RW disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.
Writing CD/DVDs on DVD+-R/+-RW drive Disclaimer (DVD-R/-RW drive) TOSHIBA does not bear responsibility for the following: ◆ Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product. ◆ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
User’s manual CD-RW:(High-Speed, Multi-Speed) MITSUBISHICHEMICALCORPORATION RICOH Co., Ltd. DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYOYUDENCO.,LTD. PIONEERVIDEOCORPORATION Matsushita Electric Industrial Co.,Ltd. DVD+R: MITSUBISHICHEMICALCORPORATION RICOH Co., Ltd. DVD Specifications for Re-recordable Disc for Version 1.1 VICTOR COMPANY OF JAPAN, LIMITED MITSUBISHCHEMICALCORPORATION MITSUBISHICHEMICALCORPORATION RICOH Co., Ltd.
Writing CD/DVDs on DVD+-R/+-RW drive ◆ Be sure to connect the universal AC adaptor before you write or rewrite. ◆ Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. ◆ Writing with software other than RecordNow! is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/RW, DVD-R/-RW or DVD+R/+RW disc.
User’s manual ◆ Damage that may be caused by using third party equipment or software.Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents.
Writing CD/DVDs on DVD Super Multi drive DVD-RW: DVD+RW: DVD-RAM: DVD Specifications for Re-recordable Disc for Version 1.1 VICTOR COMPANY OF JAPAN, LIMITED MITSUBISHCHEMICALCORPORATION MITSUBISHICHEMICALCORPORATION RICOH Co., Ltd. DVD Specifications for DVD-RAM Disc for Version 2.0 or Version 2.1 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd.
User’s manual ◆ Be sure to connect the universal AC adaptor before you write or rewrite. ◆ Before you enter standby/hibernation mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media. ◆ Be sure to close all other software programs except the writing software. ◆ Do not run software such as a screen saver, which can put a heavy load on the CPU. ◆ Operate the computer in the full-power mode. Do not use power-saving features.
Writing CD/DVDs on DVD Super Multi drive ◆ Keep mobile phones and other wireless communication devices away from the computer. ◆ Always copy data from the HDD to the DVD-RAM. Do not use cut-and-paste. The original data will be lost if there is a write error. Disclaimer (DVD Super Multi drive) TOSHIBA does not bear responsibility for the following: ◆ ◆ ◆ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product.
User’s manual ◆ ◆ ◆ ◆ ◆ If you add data to a DVD-R and DVD+R disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as Windows 98SE and Windows ME. In Windows NT4, you will need Service Pack 6 or later to read added data. In Windows 2000, you will need Service Pack 2 or later to read it. Some DVD-ROM and CD-RW/DVD-ROM drives cannot read added data regardless of the operating system.
Writing CD/DVDs on DVD Super Multi drive ◆ Do not use any discs that have been formatted with packet writing software other than DLA. Similarly, do not use any discs that have been formatted with DLA with any packet writing software other than DLA. When using a disc you are not familiar with, format it by selecting “Full Format” before using it. ◆ Do not use the Cut & Paste function for files and folders. A file or folder that has been cut may be lost if writing fails due to an error on the disc.
User’s manual 3. Click the System icon in the Performance and Maintenance window. 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the "Performance" section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the "virtual memory" section. 8. Select the Custom size button in the Virtual Memory window. 9. Specify much higher values for "Initial size" and "Maximum size." 10. Click the Set button in the Virtual Memory window. 11.
Writing CD/DVDs on DVD Super Multi drive How to learn more about InterVideo WinDVD Creator Please refer to the on-line Help for additional InterVideo WinDVD Creator information. Important information for use Note the following limitations when you write video DVD: 1. Editing digital video 2. Before recording the video to DVD ❒ When you record to DVD disc, please use only discs recommended by the Drive manufacturer. ❒ Do not set the working drive to a slow device like a USB 1.
User’s manual ❒ ❒ ❒ ❒ ❒ ❒ ❒ • Use the Mode control button and Audio/Video control button to repro duce music or voice. • Open the DVD drive. • Install, remove or connect external devices, including the following: PC card, SD card/MultiMediaCard/Memory Stick, USB devices, external display, i.LINK. devices, optical digital devices. Please verify your disc after recording important data. DVD-R/+R/-RW disc cannot be written in VR format.
Media care CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4. Hold the CD/DVD by its outside edge or the edge on the center hole. Fingerprints on the surface can prevent the drive from properly reading data. 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs. 6.
User’s manual Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. NOTE: The internal modem does not support voice functions. All data and fax functions are supported. CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Modem • When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically. • When you select a telephony location, the corresponding region is auto matically selected and it becomes the modem’s current region setting. Properties menu Click the icon with the secondary mouse button to display the following menu.
User’s manual Dialing Properties Select this item to display the dialing properties. CAUTION: If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. OPERATING BASICS 2. Plug the other end of the modular cable into a telephone jack.
Wireless communications Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. Wireless communications The computer’s wireless communication function supports Wireless LAN and devices. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.
User’s manual Security Two advanced security mechanisms ensure a high level of security: ◆ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ◆ Encryption prevents eavesdropping and maintains link privacy. Wireless communication switch You can enable or disable Wireless LAN functions, with the on/off switch. No transmissions are sent or received when the switch is off.
LAN LAN The computer has built-in support for Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN.
User’s manual 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. NOTE: When the computer is exchanging data with the LAN, the LAN active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below.
Moving the computer Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ◆ Make sure all disk activity has ended before moving the computer. Check the Disk indicator on the computer. ◆ If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely closed. ◆ Turn off the power to the computer. ◆ Disconnect the AC adaptor and all peripherals before moving the computer.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter, Ctrl and Alt keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hotkeys Hotkeys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hotkeys, the current setting will be displayed as an icon. Instant security: Press Fn + F1 to lock the keyboard and blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or move the AccuPoint.
Soft keys: Fn key combinations Hibernation: When you press Fn + F4, the computer can enter Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you check the checkbox in the dialog box, it will not appear from the next time. Display selection: Press Fn + F5 to change the active display device. When you press these hot keys a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device.
User's Manual Wireless setting: Fn + F8 are not used. . Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the Touch Pad function. When you press these hot keys, the current setting will change and be displayed as an icon. + Display resolution selection: Press Fn + space keys to change the display resolution.
Windows special keys Fn Sticky key You can use the Toshiba Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. To start the Toshiba Accessibility Utility, click start, point to All Programs (Windows 2000 only, point to Programs), point to TOSHIBA, point to Utilities and click Accessibility.
User's Manual Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode indicator lights. Now try cursor and page control using the keys shown in figure 5-2. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay.
Windows special keys Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
User's Manual Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3. Release Alt, and the ASCII character appears on the display screen. With the overlay off: 1. Hold Alt + Fn. 2. Using the overlay keys, type the ASCII code. THE KEYBOARD 3.
Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions Power on Power off (no operation) AC Battery • Operates • No charge adaptor fully • No charge • LED: Battery green connected charged • LED: Battery green DC IN green DC IN green Battery • Operates • Quick charge partially • Charge • LED: Batery Amber charged • LED: Battery Amber or no charge No • Operates • No charge main battery • No charge • LED: Battery off installed • LED: Battery off DC IN green AC Battery
Power indicators POWER AND POWER-UP MODES Power indicators The Battery, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status: Flashing amber The battery charge is low. The AC adaptor must be connected to recharge the battery.
POWER AND POWER-UP MODES User's Manual Power indicator Check the Power indicator to determine the power status. Green Blinking amber No light Indicates power is being supplied to the computer and the computer is turned on. Indicates the power was turned off while the computer was in Resume mode. The indicator turns on for one second and turns off for two seconds. Under any other conditions, the indicator does not light.
Care and use of the battery pack Real time clock battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: Check system. Then press [F1] key . . . . . .
POWER AND POWER-UP MODES User's Manual Caution : Indicates a potentially hazardous situation, Which if not avoided, may result in moderate or minor injury or property damage. Note : Provides important information. Danger 1. Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven. The battery pack could explode and cause bodily injury. 2. Never try to disassemble, repair or otherwise tamper with a battery pack. The battery pack will overheat and ignite.
Care and use of the battery pack 1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes, skin or clothing. If caustic electrolyte fluid should contact your eyes, immediately wash your eyes with large amounts of running water and seek medical attention, to help prevent eye damage. It electrolyte fluid should contact your skin immediately wash it under running water to prevent rash.
POWER AND POWER-UP MODES User's Manual 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely. Standby and Suspend will not function and data in memory will be lose. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
Care and use of the battery pack POWER AND POWER-UP MODES Procedures To recharge a battery pack while it is installed in the computer, connect the AC adaptor to the DC IN socket and plug the other end into a working outlet. The Battery indicator glows amber when the battery is being charged. CAUTION: Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Do not attempt to charge the battery pack with any other charger.
POWER AND POWER-UP MODES User's Manual ❑ The battery has not been used for a long time. ❑ The battery has completely discharged and been left in the computer for a long time. ❑ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2. Plug in the AC adaptor. 3. Charge the battery until the Battery indicator glows green.
Care and use of the battery pack A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer (for example, whether you enable batterypower saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
POWER AND POWER-UP MODES User's Manual Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (8 cell) 4 days (Resume mode) 45 days (Boot mode) Battery pack (12 cell) 6 days (Resume mode) 68 days (Boot mode) RTC battery 60 days Extending battery life To maximize the life of your battery pack: ❑ At least once a month, disconnect the computer from a power source and operate it on ba
Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes amber shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install battery packs.
POWER AND POWER-UP MODES User's Manual BATTERY SAFTY LOCK BATTERY PACK Figure 6-1 Slide the locking latches to the unlocked position 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. BATTERY RELEASE LATCH BATTERY Figure 6-2 Removing the battery pack 7. Pull the battery pack forward to remove it. CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery pack to your TOSHIBA dealer.
Starting the computer by password To install a battery pack, follow the steps below. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the battery pack. BATTERY PACK Figure 6-3 Installing the battery pack 3.
POWER AND POWER-UP MODES User's Manual 2. Enter the password. 3. Press Enter. CAUTION: If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ❑ Boot : Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ❑ Hibernation : Data in memory is saved to the hard disk.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority, keyboard, USB, LAN, general, password, parallel/printer. HW SETUP AND PASSWORDS NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
User’s Manual HW Setup window The HW Setup window contains the following tabs: Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Parallel/Printer. There are also three buttons: OK, Cancel and Apply. OK Cancel Apply Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes. Accepts all your changes without closing the HW Setup window.
HW Setup window NOTE: If you click the OK button before entering the password, Not registered will appear on the display. 3. Click the OK button. The following message appears, allowing you to verify the password. Verify Password: 4. If character strings match, the password is registered click OK button. If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: HW SETUP AND PASSWORDS 1.
User’s Manual Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bidirectional. ECP Standard Bidirectional Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) This setting should be used with some other parallel devices.
HW Setup window Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed. HT Technology Configures the Hyper-Treading Technology. Enabled with PM Enable the Hyper- Treading Technology with Power Management. Enabled without PM Disabled Enable the Hyper-Treading Technology without Power Management. Disable the Hyper-Treading Technology. Boot Priority This option sets the priority for booting the computer.
User’s Manual You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB diskette drive. N Selects the Network. 1 Selects the primary HDD. C Selects the CD-ROM*. This procedure does not affect the settings. * In this computer, CD refers to the DVD-ROM, CD-RW/DVD-ROM, DVD-R/RW, DVD+-R/+-RW or DVD Super Multi drives. HW SETUP AND PASSWORDS To change the boot drive, follow the steps below. 1.
HW Setup window USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Disabled Enables the USB KB/Mouse Legacy Emulation. (Default) Disables the USB KB/Mouse Legacy Emulation. USB-FDD Legacy Emulation Use this option to enable or disable USB-FDD Legacy Emulation. Enables the USB-FDD Legacy Emulation.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
User’s Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safety Remove Hardware icon on the system tray and disable the PC card. 2. Press the eject button of the PC card you want to remove to extend the button. 3. Press the extended eject button to pop the card out slightly. 4. Grasp the PC card and remove it.
User’s Manual SD card/MultiMediaCard/Memory Stick The computer is equipped with a SD card/MultiMediaCard/Memory Stick slot that can accommodate Secure Digital flash memory cards with capacities of 8MB, 16M, 32MB, 64MB, 128MB, 256MB and 512MB. MultiMediaCard 8MB, 16M, 32MB, 64MB, 128MB.
SD card/MultiMediaCard/Memory Stick CAUTION: Make sure the SD card/MultiMediaCard/Memory Stick is oriented properly before you insert it. NOTE: If Windows fail to read the SD card/MultiMediaCard,/Memory Stick remove it then reinsert it. Removing an SD card/MultiMediaCard/Memory Stick To remove an SD card/MultiMediaCard/Memory Stick, follow the steps below. 1. Open the Safety Remove Hardware icon on the system tray and disable the SD card/MultiMediaCard/Memory Stick. 2.
User’s Manual 2. Please do not remove the SD card/MultiMediaCard/ Memory Stick from the SD card/MultiMediaCard/ Memory Stick slot while in Standby or in Hibernation state. If you do, PC may become unstable or the data in SD card/MultiMediaCard/Memory Stick may be lost. 3. Please do not turn off PC or go into Standby/Hibernation ,while computer is accessing the card; If you do, PC may become unstable or you may lose data.
Memory expansion 2. Remove all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-Up Modes.) 4. Remove one screw securing the memory module cover. 5. Lift off the cover. NOTE: Use a point size 0 Flippest screwdriver. OPTIONAL DEVICES Figure 8-5 Removing the cover 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7.
User’s Manual 8. Seat the cover and secure it with one screw. 9. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. OPTIONAL DEVICES CAUTIONS: 1.
Additional battery pack 7. Seat the cover and secure it with one screw. Additional battery pack 12 Cell You can increase the portability of the computer with additional battery packs (12 cell : PA3382). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
User’s Manual Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly. You can also connect a parallel printer . To connect a printer, follow these steps: 1. Turn off the computer. 2.
Television NOTE: The Resume feature can be used with an external monitor. Simply enable Resume and the computer will maintain the data as it is displayed on the external monitor. 1. Connect the monitor to the external monitor port. 2. Turn the monitor’s power on. When you turn on the power, the computer automatically recognizes the monitor and determines whether it is color or monochrome. You can use the HW Setup to select between Auto-Selected and Simultaneous displays.
User’s Manual Figure 8-8 Connecting a television OPTIONAL DEVICES 3. Turn the television on. 4. Turn the computer on. Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Hardware and system checklist Problem Procedure Computer shuts down and DC IN indicator blinks amber Leave the computer off until the DC IN indicator stops blinking. NOTE: It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN indicator stops blinking. If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer.
User's Manual Battery If you suspect a problem with the battery, check the DC IN and battery indicators. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power the computer The battery may be discharged. Connect the AC adaptor to charge the battery. Battery doesn’t charge when the AC adaptor is attached (Bttery indicator does not glow amber.) If the battery is completely discharged, it will not begin charging immediately.
Hardware and system checklist If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t power the computer as long as expected If you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again. Check the power consumption settings in Power Saver utility. Consider using a power saving mode.
User's Manual LCD panel TROUBLESHOOTING Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the LCD They might have come from contact with the keyboard, TouchPad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner.
Hardware and system checklist Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. Refer to your OS documentation or online HELP for information on running SCANDISK and the defragmenter. As a last resort, reformat the hard disk. Then, reload the operating system and other files. If problems persist, contact your dealer. DVD-ROM drive For more information, refer to Chapter 4, Operating Basics.
User's Manual Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using.
Hardware and system checklist Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. Refer to Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
User's Manual • Do not connect/ disconnect external devices or install/ remove internal cards during writing. If problems persist, contact your dealer. DVD-R/-RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
Hardware and system checklist CD-ROM: CD-DA, CD-Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROMXA Mode 2 (Form1, Form2), Enhanced CD(CD-EXTRA), CD-G(Audio CD only), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD-R/-RW drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour.
User's Manual A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD run correctly The software or hardware configuration may be , but others do not causing a problem. Make sure the hardware configuration matches your software’s needs.
Hardware and system checklist • Do not connect/ disconnect external devices or install/ remove internal cards during writing. If problems persist, contact your dealer. DVD Super Multi drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
User's Manual CD-ROM: CD-DA, CD-Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROMXA Mode 2 (Form1,Form2), Enhanced CD(CDEXTRA),CD-G(Audio CD only), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions : • Use only media recommended by TOSHIBA.
Hardware and system checklist You cannot access the external 3 1/2" diskette drive Try another diskette. If you can access the diskette, the original diskette (not the drive) is probably causing the problem. If problems persist, contact your dealer. Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do not work as expected Check that the device is connected to an electric outlet.
User's Manual Inspect the cable connecting the printer to the computer for damage. Make sure it is securely connected. A parallel printer connects to the parallel port and a serial printer to the serial port. Make sure the ports are configured correctly. Make sure your software is configured to recognize the printer. Check your printer and software documentation. Printer error Check your printer documentation. If problems persist, contact your dealer.
Hardware and system checklist The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Option tab. 3. Set the speed as instructed and click OK. When the reaction of Touch pad is sensitive too slow Adjust the touch Sensitivity. 1. Open the Control Panel. 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4.
User's Manual USB mouse This section applies only with Windows®XP operating systems. Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. TROUBLESHOOTING 1.
Hardware and system checklist PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reset the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
User's Manual Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/ O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. TROUBLESHOOTING If problems persist, contact your dealer.
Hardware and system checklist NOTE: If you turn the computer off in Resume mode while the display is on TV, the computer will select either the internal LCD or an external computer CRT as the display device. If problems persist, contact your dealer. USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
User's Manual You can hear a dial tone but can't make a call If the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled. You can also use the ATX command. Refer to the chapter on AT commands in online help files for Appendix C, AT Commands. You place a call, but a connection can't be made Make sure the settings are correct in your communications application.
Hardware and system checklist You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. Refer to the chapter on S-registers in online help files for Appendix D, S-registers. If problems persist, contact your dealer.
User's Manual Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on. If problems persist, consult your LAN administrator. i.LINK (IEEE1394) Problem Procedure i.
TOSHIBA support TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
TROUBLESHOOTING User's Manual Outside of Europe InEurope Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road Germany & Austria North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R8H2 China TOSHIBA Computer Systems (Shanghai)Co. Ltd. Bldg.33,No.351,Jinzang Road, Pudong New Area, Shanghai, P .R. China 201206 Singapore TOSHIBA Singapore Pte. Ltd.
Appendix A Specifications ..................................................................................... A-1 Appendix B Display Controller and Modes ...........................................................B-1 Appendix C AT Commands ....................................................................................C-1 Appendix D S-registers ........................................................................................... D-1 Appendix E V.90 ...............................................
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 343 (w) x 282(d) x 37.5(front) /49 (rear) millimeters (does not include the thicker part of the bottom of the computer) Weight(typical*) 3.54kilograms(Approximate), configured with :15"XGA display, fixed DVD-ROM drive, 256MB memory, 40GB(4200rpm) HDD, and 8 cells or 12 cells battery. * Weight will vary depending on whether or not and what kind of options are adopted.
APPENDIX A User's Manual Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec V.21/V.22/V.22bis/V.32 (FormerCCITT) /V.32bis/V.34/V.90 Bell 103/212A Fax ITU-T-Rec V.17/V.29/V.27ter (Former CCITT) /V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. Three models are available: 14.1" XGA, 1024 horizontal x 768 vertical pixels 15.
User's Manual Video Modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn Any command issued is acknowledged with a response in either text or numeric values known as result codes.
User's Manual A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
Appendix C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. En Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. E0 Disables echo to the computer.
User's Manual Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode APPENDIX C This command turns the speaker on or off. M0 The speaker is off. M1 The speaker is on until the modem detects the carrier signal (default). M2 The speaker is always on when modem is off-hook.
Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Result Codes: OK n=0,1,3 P Select pulse dialing This command configures the modem for pulse (non touch-tone) dialing.
User's Manual T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
Appendix C X5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT , RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. Busy tone detect APPENDIX C Disabled: The modem ignores any busy tones it receives.
User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise &Dn DTR control APPENDIX C This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard tone to 550 Hz. &G2 Sets guard tone to 1800 Hz. Result Codes: n=0,1,2 OK ERROR Otherwise &Kn Local flow control selection Disable flow control.
User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result Codes: OK n=0 CONNECT n=1 ERROR Otherwise APPENDIX C &V Display Current Configuration This command displays the current configuration of the modem.
Appendix C \Nn Error control mode selection \ This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode. \N3 V.42, MNP, or buffered (default). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode.
User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 OK ERROR Otherwise %B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: rings S1 Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII S5 Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only.
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.
Appendix D S37 Dial line rate maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps APPENDIX D S37 = 0 (default) D-5
User's Manual AT command set result codes The following table shows the result codes.
Appendix D rResult Code Numeric Description DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLISTFULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V. 34 rate. NOTE: V.
User's Manual APPENDIX E Table E-1 Result codes for a V.90 connection No.
Appendix E AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications Form Factor Capability ■ ■ ■ Network Operating System Media Access Protocol Data Rate ■ ■ ■ ■ ■ ■ Mini PCI TypeIII IEEE 802.
APPENDIX F User’s Manual ■ Band 5 GHz (5150-5850 MHz) (Revision A, Turbo Mode) ■´ Band 2.4 GHz (2400-2483.5 MHz) (Revision B) Modulation Technique Direct Sequence Spread Spectrum ■´ CCK, DQPSK, DBPSK (Revision B) ■´ OFDM-BPSK, OFDM-QPSK, OFDM16QAM, OFDM-64QAM (Revision A, Turbo Mode) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.
Appendix F Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range Channel ID 36 40 44 48 52 56 60 64 149 153 157 161 5150-5850 MHz 5180 5200 5220 5240 5260 5280 5300 5320 5745 5765 5785 5805 Note US only * US only * US only * US only * * Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition: A Wireless LAN card receives a “US county/region code” beacon of the standard IEEE 802.11 (Revision D) from a Wireless LAN Access Point.
APPENDIX F User’s Manual Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 42 50 58 152 160 5150-5850 MHz 5210 5250 5290 5760 5800 Note US only * US only * US only * US only * US only * * Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition: A Wireless LAN card receives a “US county/region code” beacon of the standard IEEE 802.11 (Revision D) from a Wireless LAN Access Point.
Appendix G Power Cord and Connectors Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix H Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the modem board To install the modem board, follow the steps below. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4.
User’s Manual Removing the modem board To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the modem cover and remove the cover. 5. Remove two screws securing the modem board. 6. Lift out the modem board. 7. Disconnect the modem board cable. 8. Secure the modem board with two screws removed in step 5. APPENDIX H 9.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD modules and communication devices.
The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
GLOSSARY AccuPoint (Abbreviationscontinued) SO-DIMM: small-outline dual in-line memory module SVGA: super video graphics array SDRAM: synchronized dynamic random access memory TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRM: video ready modem VRT: voltage reduction technology A adapter: A device that provides an interface between two dissimilar electronic devices.
Byte AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer. B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. See also AUTOEXEC.BAT. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers.
GLOSSARY cache memory C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. CGA: Color/graphics adapter.
delete components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
GLOSSARY device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). dialog box: A window that accepts user input to make system settings or record other information.
host computer Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support. F fast infrared: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file: A collection of related information; a file can contain data, programs, or both. firmware: A set of instructions built into the hardware which controls and directs a microprocessor’s activities.
GLOSSARY hot dock/undock hot dock/undock: Connecting or disconnecting a device to or from the computer while the computer’s power is turned on. hotkey: The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel.
modem kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte and megabit. L M main board: See motherboard. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720x350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. level 2 cache: See cache.
GLOSSARY monitor monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
RAM password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject. pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse.
GLOSSARY restart restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. RCA jack: A single-pin connector that carries composite video signals, which include both contrast and color information. See also S-video. RGB: Red, green, and blue.
write protection V synchronous: Having a constant time interval between successive bits, characters or events. volatile memory: Random access memory (RAM) that stores information as long as the computer is connected to a power source. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk.
Index D AC adaptor 1-7, 2-5 DC IN 19V port 2-5, 2-9 additional 1-13, 8-9 connecting 3-5 ASCII characters 5-10 Auto power on, See Power DVD-R/-RW 1-5, 4-11 DVD+-R/+-RW 1-5, 4-13 DVD Super Multi 1-6, 4-16 DC IN indicator 2-9, 6-3 Disk indicator 2-11 Diskette care 4-25 Diskette drive 1-4 connecting 4-2 disconnecting 4-3 problems 9-16 using 4-2 Display 1-6, 2-8, See also Video modes and Monitor external automatic power off 1-9 controller 1-6, Appendix B opening 3-6 selection, See Hot keys Documentation list 1
User's Manual INDEX F Fn key emulation 5-7 Fn + Alt (enhanced keyboard simulation) 5-3 Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn-esse 1-11 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-4 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 (display brightness) 5-5 Fn + F8 (wireless setting) 5-6 Fn + F9 (Touch Pad mode) 5-6 Fn + F10 (arrow mode) 5-3, 5-8 Fn + F11 (numeric mode) 5-
Index P LAN, See also Wireless LAN 1-8 cable types 4-31 connecting 4-31 disconnecting 4-32 problems 9-25 using 4-30 LCD, See Display, Video modes, Monitor external Level 2 cache, See Cache memory Lock, security, See Security lock Panel power on/off, See Power Parallel port, See Ports, parallel Password power on 1-10 starting the computer with 6-15 user 7-2 PC card 1-8 installing 8-2 location of slots 2-2 problems 9-21 removing 8-3 Ports DC IN 19V 2-4, 2-5 external monitor 1-7, 2-5 headphone, See Sound sy
INDEX User's Manual DVD-ROM drive 9-9 hard disk drive 9-8 hardware and system checklist 9-3 infrared port 9-17 i.
