Safety Precautions Operating Instructions Installation Instructions Care and Cleaning Troubleshooting Tips USER MANUAL Remote Control and App Instructions Portable Type Room Air Conditioner RAC-PT1411HWRU WARNING Warning notices: Before using this product, please read this manual carefully and keep it for future reference. The design and specifications are subject to change without prior notice for product improvement. Consult with your dealer or the manufacturer for details.
User Manual Safety Precautions .................................................................................................................... 3 Operating Instructions ............................................................................................................ 8 Installation Instructions ........................................................................................................ 12 Care and Cleaning ............................................................................
To prevent injury to the user or other people and property damage, the instructions shown here must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The level of risk is shown by the following indications. WARNING This symbol indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION This symbol indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
Safety Precautions WARNING • Do not damage or use an alternate power cord. It may cause fire and electric shock. If the power cord is damaged, it must be replaced by the manufacturer in order to avoid a hazard. • Do not direct airflow straight into persons to avoid possible health hazard. • Do not open the unit during operation. It may cause electric shock. • Do not use the power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc. It may cause an explosion or fire.
CAUTION • Do not put a pet or house plant where it will be exposed to direct air flow. This could injure the pet or harm the plant. • Hold the plug by the head of the power plug when taking it out. Otherwise, it may cause electric shock and damage. • Ensure that the installation is properly secured to prevent the product from potentially falling. • Do not place heavy objects on the power cord and ensure that the cord is not compressed. Otherwise, there is danger of fire or electric shock.
EXPLANATION OF SYMBOLS DISPLAYED ON THE UNIT Safety Precautions WARNING This symbol shows that this appliance used a flammable refrigerant. If the refrigerant is leaked and exposed to an external ignition source, there is a risk of fire. CAUTION This symbol shows that the operation manual should be read carefully. CAUTION This symbol shows that a service personnel should be handling this equipment with reference to the installation manual.
Operation of Current Device The power supply cord contains a current measuring device that detects damage to the power cord. Test your power supply cord as follows: RESET 1. Plug in the air conditioner. TEST 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out. 3. Press the RESET Button. You will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit.
OPERATING INSTRUCTIONS Preparation Control panel Outlet louver (automatic swing) Upper air filter (behind the grille) (both sides) Inlet and outlet air hose Operating Instructions Handle Air inlet Panel Drain Outlet (dry mode) Drain Outlet (heating mode) Power plug storage Caster Power cord storage Power cord outlet Drain Outlet (excess condensate) Front Rear Unit Operating Temperature Range: Page 8 Mode Temperature Range Cool 60°F ~ 95°F (16°C ~ 35°C) Dry 55°F ~ 95°F (13°C ~ 35°C) Heat
Control Panel Features Swing (Connect) Button Wireless Indicator Mode Button Up ( ) and Down ( Buttons Swing Button Used to initiate the Auto Swing feature. When the operation is ON, pressing the SWING button can stop the louver at the desired angle. Connect Button The swing button is also used to initiate the wireless connection mode.To initiate the wireless connection mode, power on the air conditioner then press the SWING button for 3 seconds.
Shows Error codes and protection code: E1 - Room temperature sensor error. E2 - Evaporator temperature sensor error. E3 - Condenser temperature sensor error (select models). E4 - Display panel communication error. P1 - Bottom tray is full - Connect the drain hose and drain the collected water away. If protection code repeats, call for service. NOTICE When one of these error codes occurs, turn off the unit and check for any obstructions. Restart the Unit.
SLEEP operation Pressing this button will increase (during cooling operation) or decrease (during heating operation, applicable models) 1°F/1°C after 30 minutes. The temperature will again increase (cooling) or decrease (heating) by another 1°F/1°C after an additional 30 minutes. This new temperature will be maintained for 7 hours before returning to the originally selected temperature. This ends the Sleep mode and the unit will continue to operate as originally programmed.
INSTALLATION INSTRUCTIONS Choosing the Right Location 50 cm 19.7 inch Your installation location should meet the following requirements: • Make sure that you install your unit on an even surface to minimize noise and vibration. • The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible. • The unit should be located at least 12” (30cm) from the nearest wall to ensure proper air conditioning.
Tools Needed • • • Phillips screwdriver Tape measure or ruler Knife or scissors • Saw (optional, to shorten window adaptor for narrow windows). Accessories Your Window Installation Kit fits windows 19.4’’-62.2’’ (49.3-158.1 cm). Please doublecheck all packaging materials to make sure accessories do not get accidentally thrown away.
Window Installation Kit 1: For Hung Window types only Air Exhaust Adapter Insert the Air Exhaust Adapter into the exhaust of the hose (the circular opening) for optimal performance. Rotate the adapter clockwise until the locking tabs click and it no longer rotates. Skip this step if installing into a horizontal sliding window. The Air Exhaust adapter may interfere with some window screens, and can be removed if desired (Please note this may slightly decrease performance).
Foam seal B (Adhesive type-shorter) Type 1: Hung window installation 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. 2. Insert the window slider assembly into the window track. If the hose opening is covered by the lip of the window frame, rotate the panel so the thicker side faces the window frame.
Foam seal B (Adhesive type-shorter) Type 2: Sliding window Installation (Optional) 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. 2. Assembling the Sliding Window Adapter (Only needed for Sliding Window applications): Align both halves of the sliding window adapter and connect them. Then, attach the air divider to the newly formed window adapter on the outdoor side.
6. If desired, install the security bracket with 2 screws as shown. 7. Attach the Sliding Window Adapter to the hose by lining up the circles on the adapter the hose. Insert the window slider adapter into the hole of the window slider. Security Bracket 2 Screws Installation Instructions NOTICE To ensure proper function, DO NOT overextend or bend the hose. Make sure that there are no objects within 20in (~500mm) of the inlet and outlet hose.
Water Drainage (For Heating Mode) • Remove the middle drain plug While operating in heat pump mode, the unit will produce condensate that must be drained. You must install the drain hose when operating in heat mode. To install the drain hose, remove the plug from the drain port and attach the included hose. The universal drain adaptor can be attached to the end of the included hose. A 3/4” hose (not included) can be attached to the adaptor if a longer hose length is required.
CARE AND CLEANING Safety Precautions • • • • Always unplug the unit before cleaning or servicing. DO NOT use flammable liquids or chemicals to clean the unit. DO NOT wash the unit under running water. Doing so causes electrical danger. DO NOT operate the machine if the power supply was damaged during cleaning. A damaged power cord must be replaced with a new cord from the manufacturer.
TROUBLESHOOTING TIPS Before calling service, review this list. It may save you time and expense. This list includes common occurences that are not the result of defective workmanship or materials of this appliances. Problem Solution Unit does not turn on when pressing ON/ OFF button Displays P1 Error Code and means the water collection tray is full. Turn off the unit, drain the water from the water collection tray, and restart the unit.
HEAT PUMP HOSE INSULATION FOAM If you are experiencing condensation on the outer section of the hose during heating operation, apply the included heat pump insulation foam to the outside of the hose. Use the included zip ties to secure the foam around the hose.
REMOTE CONTROL AND APP INSTRUCTIONS Handling the Remote Control LOCATION OF THE REMOTE CONTROL Use the remote control within a distance of 26 ft. (8m) from the air conditioner, pointing it towards the unit. The unit will beep when it receives a signal. CAUTION • The air conditioner will not operate if curtains, doors or other materials block the signals from the remote control to the unit. • Prevent any liquid from spilling onto the remote control.
Function Buttons ON/OFF Turns the unit on or off. TEMP Increases temperate in 1°F (1°C) increments. Max. temperature is 86°F (30°C). SET Scrolls through operation functions as follows: Fresh ( ) J Follow Me ( ) J AP mode ( ) J Fresh... The selected symbol will flash on the display area, press the OK button to confirm. TEMP Decreases temperature in 1°F (1°C) increments. Min. temperature is 60°F (16°C). FAN SPEED Switches the fan speed as follows: Auto J Low J Medium J High ...
Remote Screen Indicators Information is displayed when the remote control is powered on. Fresh feature display Sleep mode display Follow me feature display Wireless control feature display Low battery detection display (If flashes) MODE display Displays the current mode, including: Transmission Indicator Lights up when remote sends signal to indoor unit. LOCK display Displays when LOCK feature is activated.
Setting the Timer TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON SETTING Press TIMER ON button to initiate the ON time sequence. Press up or down button for multiple times to set the desired time to turn on the unit. Point remote to unit and wait 1sec, the TIMER ON will be activated. x5 1sec TIMER OFF SETTING Press TIMER OFF button to initiate the OFF time sequence.
DECLARATION OF CONFORMITY We hereby declare that this AC is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. SPECIFICATION OF WIRELESS MODULE Model: US-OSK103 Dimensions: 41 x 24 x 5 (mm) Standard: IEEE 802.11 b/g/n Operation Temperature: 0°C ~ 45°C / 32°F ~ 113°F. Antenna Type: External omnidirectional Antenna Operation Humidity: 10% ~ 85% Frequency: 2.4 GHz (wireless) Power Input: DC 5V/300 mA Maximum Transmitted Power: 15 dBm Max PRECAUTIONS 1.
SYSTEM OVERVIEW Devices required to use the Smart AC: 1. Smart Phone with compatible iOS or Android system. 2. Wireless Router (a 2.4GHz network is required to connect). 3. Smart Air Conditioner. DOWNLOAD AND INSTALL THE APP Android QR code Apple QR code Scan to download app. • You can also go to Google Play or App Store and search for Toshiba NA AC. For more information, please refer to Toshiba Lifestyle website: us.toshiba-lifestyle.com.
CREATE YOUR ACCOUNT • Make sure your smartphone is connected to your wireless router and your wireless router has a working 2.4GHz internet connection. It is recommended to activate your account immediately to be able to recover your password by email. • Remote Control and App Instructions 1. Press “Sign Up”. 2. Enter your email address and password. 3. Press “Registration”. 4. If you forget your password, press “Forgot password?” on the main menu and enter your email address.
ADDITIONAL APP AND SMART HOME FUNCTIONS For additional instructions regarding the features of the app and Smart Home skill capabilities, scan the QR code below.
Precauciones de Seguridad Instrucciones de Operación Instrucciones de Instalación Mantenimento Y Limpieza Soluciones de Problemas MANUAL DEL USUARIO Instrucciones del Control Remoto y del App Tipo Portatil Aire Acondicionado de Habitación RAC-PT1411HWRU WARNING Warning notices: Antes de usar este producto, lea atentamente este manual y consérvelo para futuras referencias. El diseño y las especificaciones están sujetos a cambios sin previo aviso para la mejora del producto.
Manual del propietario Precauciones de Seguridad ............................................................................................... 33 Instrucciones de Operación ............................................................................................... 38 Instrucciones de Instalación .............................................................................................. 42 Mantenimiento y Limpieza ......................................................................................
Para evitar daños al usuario u otras personas y a la propiedad, las instrucciones que se muestran aquí deben ser seguidas. Las operaciones incorrectas por la ignora de las instrucciones podría causar perjuicios o lesiones. El nivel de riesgo está clasificado por las siguientes indicaciones. ADVERTENCIA Este símbolo indica una situación peligrosa que, si no evitada, podría causar la muerte o lesiones graves.
Precauciones de Seguridad ADVERTENCIA • No desmonte ni modifique la unidad. Puede causar fallas y descarga eléctrica. • No dañe ni utilice un cable de alimentación alternativo. Puede causar incendio y descarga eléctrica. Si el cable de alimentación está dañado, debe ser reemplazado por el fabricante o un centro de servicio técnico autorizado o una persona igualmente calificada para evitar un peligro. • No dirija el flujo de aire directamente a las personas para evitar posibles riesgos para la salud.
• Tenga cuidado al desempacar e instalar. Los bordes afilados podrían causar lesiones. • No limpie el acondicionador de aire con agua. El agua puede entrar en la unidad y degradar el aislamiento que podría conducir a una descarga eléctrica. • No lo guarda una mascot o plantas donde sera expuesto al flujo del aire directo. Podría hacer daño a su mascot o planta. • Sujete el enchufe junto a la cabeza cuando sacarlo. De lo contrario, puede causar descarga eléctrica y daños.
EXPLICACIÓN DE LOS SÍMBOLOS MOSTRADOS EN LA UNIDAD Precauciones de Seguridad Este símbolo muestra que este aparato ha utilizado un refrigerante ADVERTENCIA inflamable. Si el refrigerante está filtrado y exposto a una fuente de ignición externa, hay riesgo de incendio. PRECAUCIÓN Este símbolo muestra que el manual de instrucciones debe leerse cuidadosamente. PRECAUCIÓN Este símbolo muestra que un personal de servicio técnico debe manipular este equipo con referencia al manual de instalación.
Enchufe y pulse el botón RESET El cable de energía contiene un dispositivo de medición que detecta daños en el proprio cable. Pruebelo de la siguiente manera: 1. Enchufe el acondicionador de aire. 2. El cable de energía tendrá DOS botones en el cabezal del enchufe. Pulse el botón TEST. Notará un clic a medida que aparezca el botón RESET. 3. Pulse el botón RESET. Notará un clic a medida que el botón se activa. 4. El cable de energía ahora está energizando la unidad.
INSTRUCCIONES DE OPERACIÓN Preparación Panel de control Deflector de aire (oscilación automática) (detrás de la rejilla) Mango de traslado Instrucciones de Operación (ambos os lados) Panel Filtro de aire superior Manguera de aire salida y entrada Entrada de aire Salida de drenaje (modo dry) Salida de drenaje (modo heating) Soporte del enchufe Rodízio Frente Soporte del cable Salida del cable Salida de drenaje (exceso de condensado) Trasera Faja de Temperatura de Funcionamiento de la Unidad: Mod
Característica del Panel de Control Botón del Swing (Connect) Indicador del Wireless Botón del Mode Arriba ( Botones ) y Abajo ( Botón Oscilación (Swing) Se utiliza para iniciar la función de oscilación automática. Cuando la operación está activada, al pulsar el botón Swing se puede detener el deflector en el ángulo deseado. Función Connect (Smart models only) El botón Swing se utiliza para iniciar el modo de conexión inalámbrica.
Códigos de Error y códigos de protección: E1 - Error en el sensor de temperatura de la habitación. E2 - Error en el sensor de temperatura del evaporador. E3 - Error del sensor de temperatura del condensador (modelos selecionados). E4 - Error en la comunicación de la pantalla del panel. P1 - La bandeja inferior está llena: conecte la manguera de drenaje y drene el agua acumulada. Si el código de protección se repite, llame al servicio técnico.
Funcionamiento del Modo Sueño (SLEEP) Al pulsar este botón se aumentará (durante la operación de enfriamiento) o se disminuirá (durante operación de calefacción, en modelos aplicables) 1 °F/1 °C después de 30 minutos. La temperatura volverá a aumentar (enfriar) o disminuir (calentar) en otros 1 °F/1 °C después de 30 minutos adicionales. Esta nueva temperatura se mantendrá durante 7 horas antes de volver a la temperatura seleccionada originalmente.
INSTRUCCIONES DE INSTALACIÓN Elección de la Ubicación Correcta 50 cm 19.7 inch Su ubicación de instalación debe cumplir los siguientes requisitos: • Asegúrese de instalar la unidad en una superficie uniforme para minimizar el ruido y las vibraciones. • La unidad debe instalarse cerca de un enchufe conectado a tierra y el sistema de drenaje de la bandeja (que se encuentra en la parte trasera de la unidad) debe ser accesible.
Herramientas Necesarias • • • Destornillador Phillips Regla o cinta métrica Tijera o cuchillo • Sierra (opcional, para acortar el adaptador de ventana para ventanas estrechas). Accesorios El kit de instalación de ventanas es adaptable a ventanas de 19,4’’-62,2’’ (49,3-158,1 cm). Verifique dos veces todos los materiales de embalaje para asegurarse de que los accesorios no se desechen accidentalmente.
Kit de Instalación en Ventanas 1: Solamente para ventanas de colgar Adaptador de aire de escape Inserte el adaptador de aire de escape en la manguera de escape (la abertura circular) para un rendimiento óptimo. Gire el adaptador en el sentido de las agujas del reloj hasta que las pestañas de bloqueo hagan clic y ya no gire. Omita este paso si lo instala en una ventana deslizante horizontal.
Foam B B Sello deseal espuma (Adhesivemás type-shorter) (Adhesivo corto) Tipo 1: Instalación en ventanas de colgar 1. Corte las tiras A y B del sello de espuma adhesiva a las longitudes adecuadas y fíjelas al marco y al marco de la ventana como se muestra. 2. Inserte el conjunto deslizador de ventana en el carriel de la ventana. Si la abertura de la manguera está cubierta por el borde del marco de la ventana, gire el panel de modo que el lado más grueso mire hacia el marco de la ventana.
seal BB SelloFoam de espuma (Adhesive (Adhesivo más corto) type-shorter) Sello de Tipo 2: Instalación en ventanas de deslizar (Opcional) 1. Corte las tiras A y B del sello de espuma adhesiva a las longitudes adecuadas y fíjelas al marco y al marco de la ventana como se muestra. 2. Montaje del adaptador de ventana de deslizar (solo necesario para aplicaciones de ventana de deslizar): Alinee ambas mitades del adaptador de ventana de deslizar y conéctelas.
6. Si lo desea, instale el soporte de seguridad con 2 tornillos como se muestra. 7. Conecte el adaptador de ventana de colgar a la manguera alineando los círculos en el adaptador de la manguera. Inserte el adaptador del deslizador de la ventana en el orificio del deslizador de la ventana. Soporte de Security seguridad Bracket Screws 22Tornillos Instrucciones de Instalación AVISO Para garantizar un funcionamiento correcto, NO extienda demasiado ni doble la manguera.
DRENAJE DEL AGUA (Para el modo de calefacción) • Retire el tapón medio de drenaje AVISO Manguera de drenaje Instrucciones de Instalación Debido a que esta unidad contiene una bomba de condensado, la manguera de drenaje se puede elevar hasta 6 pies (1,8 m). Dirija la manguera hacia el drenaje, asegurándose de que no haya torceduras que restrinjan el flujo de agua. Asegúrese de que el extremo de la manguera esté dirigido hacia abajo (consulte la figura con el símbolo de marca de verificación ).
MANTENIMIENTO Y LIMPIEZA Precauciones de Seguridad • • • • Desenchufe siempre la unidad antes de limpiarla o repararla. NO use líquidos o productos químicos inflamables para limpiar la unidad. NO lavar la unidad con agua corriente. Hacerlo causa peligro eléctrico. NO opere la unidad si la fuente de alimentación se dañó durante la limpieza. Un cable de alimentación dañado debe ser reemplazado por uno nuevo del fabricante.
SOLUCIONES DE PROBLEMAS Antes de llamar al servicio técnico, revise esta lista. Puede ahorrarle una gran cantidad de tiempo y dinero. Esta lista incluye ocurrencias comunes que no son consecuencia de un trabajo o materiales defectuosos en el equipo. Problema Solución El aire acondicionado no pone en marcha cuando pulsa el botón ON/OFF Muestra el código de error P1 y significa que la bandeja de recolección de agua está llena.
ESPUMA AISLANTE PARA MANGUERA DE BOMBA DE CALOR Si hay condensación en la parte exterior de la manguera durante la operación de calefacción, aplique la espuma aislante de la bomba de calor incluida en la parte exterior de la manguera. Utilice las bridas incluidas para asegurar la espuma alrededor de la manguera.
INSTRUCCIONES DEL CONTROL REMOTO Y DEL APP Manejo del Control Remoto UBICACIÓN DEL CONTROL REMOTO Utilice el control remoto a distancia a una distancia de 26 piés (8 metros) del acondicionador de aire, apuntando hacia el receptor. La recepción se confirma con un pitido. PRECAUCIÓN • El acondicionador de aire no funcionará si las cortinas, puertas u otros materiales bloquean las señales del control remoto a la unidad. 26 ft (8 metros) • Evite que cualquier líquido se derrame sobre el mando a distancia.
Funcionamiento de los Botones Botón ON/OFF Enciende o apaga la unidad. Botón TEMP Aumenta la temperatura en incrementos de 1°F (1°C). Temperatura max. es 86°F (30°C). Botón SET Se desplaza por las funciones de operación de la siguiente manera: Comfort Sense ( ) J AP mode ( ) J ... El símbolo seleccionado parpadeará en el área de visualización, pulse el botón OK para confirmar. Botón TEMP Disminuye la temperatura en incrementos de 1°F (1°C). Temperatura min. es 60°F (16°C).
Indicadores de la Pantalla del Control Remoto Las informaciones se muestran cuando se enciende el control remoto. Función Sleep activada Función Comfort Sense activada Modo Wireless activado Detección de batería baja (Si parpadea) Presenta MODE Muestra el modo actual, que incluye: Indicador de Transmission Se enciende cuando el control remoto envía una señal a la unidad interior. Presenta LOCK Aparece cuando la función BLOQUEO está activada.
Configuración del Timer (temporizador) TIMER ON/OFF - Establezca la cantidad de tiempo después del cual la unidad se encenderá / apagará automáticamente. CONFIGURACIÓN del TIMER ON Pulse TIMER ON para iniciar la secuencia de tiempo de encender (ON). Pulse los botones arriba o abajo varias veces para configurar el tiempo deseado para encender la unidad. x5 Apunte el control remoto a la unidad y espere 1 segundo, el TIMER ON se activará.
DECLARACIÓN DE CONFORMIDAD Declaramos que este Acondicionador de Aire cumple los requisitos esenciales y otras disposiciones pertinentes de la Directiva 1999/5/CE. ESPECIFICACIÓN DEL MÓDULO INALÁMBRICO Modelo: US-OSK103 Dimensiones: 41 x 24 x 5 (mm) Estándar: IEEE 802.11 b/g/n Tipo de antena: Antena omnidireccional externa Temperatura de funcionamiento: 0°C ~ 45°C / 32°F ~ 113°F. Frecuencia: 2.
VISIÓN GENERAL DEL SISTEMA Dispositivos necesarios para utilizar el Acondicionador de aire inteligente: 1. Smartphone con sistema iOS o Android compatible. 2. Router inalámbrico 3. Acondicionador de aire Inteligente DESCARGAR E INSTALAR LA APLICACIÓN Código QR de Android Código QR de Apple Escanear para descargar la aplicación. • También puede ir a Google Play o App Store y buscar Toshiba NA AC. Para obtener más información, consulte la página web de Toshiba Lifestyle: us.toshiba-lifestyle.com.
CREA TU CUENTA • Asegúrese de que su Smartphone esté conectado a su router inalámbrico y que su router inalámbrico tenga una conexión a Internet de 2,4 GHz. Se recomienda activar su cuenta inmediatamente para poder recuperar su contraseña por correo electrónico. • Instrucciones del control remoto y del App 1. Pulse “Registrarse”. 2. Introduzca su dirección de correo electrónico y contraseña. 3. Pulse “Registro”. 4.
FUNCIONES ADICIONALES DE LA APLICACIÓN Y SMART HOME Para obtener instrucciones adicionales sobre las características de la aplicación y las capacidades del sistema Smart Home, escanee el código QR a continuación Instrucciones del control remoto y del App User Manual Page 59