MAGNIA Z300 User’s Guide ™
Model: MAGNIA Z300 FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Warning Label Some warning labels are attached to units of this equipment, as shown below.
1. 2.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully, and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
Disclaimer The information contained in this manual, including but not limited to any instructions, descriptions and product specifications, is subject to change without notice. TOSHIBA CORPORATION (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING.
vii EU Declaration of Conformity EU Übereinstimmugserklärung Déclaration de conformité UE Declaración de conformidad de la UE Dichiarazione di conformità UE EU Försäkran om Överensstämmelse Toshiba declares, that the product: SYU3740*/SYU3749* conforms to the following Standards: Toshiba erklärt, daβ das Produkt: SYU3740*/SYU3749* folgenden Normen entspricht: Toshiba déclarent que le produit cité ci-dessocus: SYU3740*/SYU3749* est conforme aux normes suivantes: Toshiba declaran que el producto: SYU3740*/SYU
Introduction Key features of the MAGNIA Z300 c Compact chassis of 2U 1/2 widths c Installation flexibility (Rack and Micro Tower) c Up to two Pentium III processors (866 MHz, 1 GHz) c One 64bit/66MHz PCI slot c Main memory expandable to a maximum of 3 GB c 24-speed CD-ROM drive as standard c Up to two 76 GB hard disk drives (IDE) c IDE RAID as standard (RAID 0 and 1) c Hot-swap hard disk drives c Ultra 160 SCSI IF c 2 LAN ports (100BASE-TX) provided as standard, ALB (Adaptive Line Balance) and AFT (Adaptiv
x c Remote management mechanism via network (power ON/ OFF, reboot provided as standard) c Server setup assist software “Toshiba Server Setup Tool” c Integrated server operation management software HarnessEye/ web c Flexibility of system configuration with external units (Exter- nal Hard Drive Unit Z1 and External Device Bay Unit Z1) NOTE: The MAGNIA Z300 meets the FCC regulations for a Class A digital device, suitable for use in a business installation.
xi Safety cautions Before attempting to use your Toshiba MAGNIA Series Server, all safety instructions must be read carefully and fully understood. This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or damage to the rack or the units installed in them.
xii Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon provides technical information about the server which, while not essential, may be of interest to you. HINT: This icon denotes helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text.
xiii c Read Me First Addendum. c Software License Agreement Service options Toshiba offers a full line of service options built around its warranty programs. See the warranty and service material included with the server for registration information. Maintenance contracts Periodic maintenance and inspection is essential for keeping the server fully operational and assuring its safe use. Toshiba recommends taking out a maintenance contract for this purpose.
Contents Chapter 1: Getting Started............................................................................. 2 Checking the items included with the server............................................ 2 Mounting optional internal devices............................................................ 4 Environmental considerations.................................................................... 5 Micro Tower Type/Rack Type............................................................... 5 Micro Tower Type...
xvi Rear view................................................................................................... 22 (1) AC connector ..................................................................................22 (2) Security Loop ..................................................................................22 I/O connectors...................................................................................... 23 Expansion slot.........................................................................
xvii Setup of system configuration................................................................. BIOS setup utility.................................................................................. SCSI utility............................................................................................. IDE RAID Setup utility......................................................................... Setup of disk array (RAID).......................................................................
xviii Chapter 3: External Unit Setup................................................................. 110 Types of External Unit............................................................................ 110 Front view of the External Hard Drive Unit Z1 (with the front panel closed)...................................................................................................... 111 Key lock...............................................................................................
xix SCSI ID............................................................................................... 130 How to Connect an External Unit......................................................... 135 Chapter 4: System Configuration Setup................................................. 138 BIOS setup utility..................................................................................... 138 Starting the setup utility.....................................................................
xx Installing the network driver.............................................................. 176 Procedure after installation of the Windows 2000 Server............ 177 NetWare................................................................................................... 178 Before installing the NetWare........................................................... 178 For installing NetWare 5.1 manually................................................ 180 For installing the NetWare 4.2 manually..........
xxi The power button does not function after abortion........................ 211 The internal clock does not keep precise time............................... 211 Trouble with Application Software........................................................ 211 Remedy When Windows NT/2000 is Usable.................................... 212 Remedy When Windows NT/2000 is Unusable................................ 213 Appendix A: Specifications.......................................................................
xxii
Chapter 1 Checking the items included with the server ............................ 2 Mounting optional internal devices ............................................ 4 Environmental considerations ..................................................... 5 Power requirements ...................................................................... 9 Front view (with the front panel closed) .................................. 10 Front view (with the front panel opened) ................................
Getting Started This chapter describes how to set up the server and to have it ready for use. Checking the items included with the server Check the items in the package according to the accompanying Read Me First Addendum. If any of the items is missing or damaged, please contact your Toshiba dealer as soon as possible.
Getting Started Checking the items included with the server NOTE: The Read Me First Addendum provides a listing of all standard accessories and their respective quantities. If you purchased the server together with an optional internal device, the optional device will also be incorporated with the standard accessories listed. However, in such a case it is possible that the quantities of some accessories, e.g.
4 Getting Started Mounting optional internal devices Mounting optional internal devices If you have purchased an optional internal device together with the server, install it before setting up the server. See “Installing/removing an optional device” on page 52. If you find it difficult to install an optional device yourself, always ask an authorized MAGNIA service provider to do it for you.
Getting Started Environmental considerations 5 Environmental considerations Micro Tower Type/Rack Type c Install the server in a clean, dust-free and well-ventilated place. c Install the server on a level and steady surface. c Never install the server upside down. c Ensure the following when installing the server: - Do not expose to direct sunlight - Do not install in locations susceptible to vibration or shock.
6 Getting Started Environmental considerations c Only operate the server under the following conditions: - Ambient temperature: 50 to 95°F (10 to 35°C) (Micro Tower Type) 50 to 89°F (10 to 32°C) (Rack Type) - Ambient humidity: 30 to 80%Rh (No condensation) NOTE: To avoid condensation when the room temperature is too high or too low, do not start your server for about one hour after the room temperature has fallen within a range of 50 to 95°F (10 to 35°C), or 50 to 89 °F (10 to 32°C) if your server is a R
Getting Started Environmental considerations 7 Micro Tower Type Leave enough space around the server for maintenance and ventilation.
8 Getting Started Environmental considerations Up to four System Units and External Units can be installed when stacked horizontally. Rack Type c Use the optional Toshiba rack and rack mount kit to install a Rack Type. c Leave a clearance of more than 24 inches (60 cm) before and behind the rack to ensure good ventilation around the server.
Getting Started Power requirements 9 Power requirements Before plugging the power cable in to a wall outlet (especially if your server is a Rack Type), ensure the following: make sure that the capacity of the power supply (current rating of the wall outlet) and that of the over-current protector (current rating of the circuit breaker) are correct. Whenever you have a question about wiring etc., always consult an authorized MAGNIA service provider. The power rating of the server is 160W.
10 Getting Started Front view (with the front panel closed) Front view (with the front panel closed) CD-ROM drive Power indicator ( ) Disk indicator ( ) Auto-shutdown indicator ( Fault indicator ( ) ) System status indicator Front panel display Display change button USB 1 connector USB 2 connector Key lock Front view with the front panel closed Key lock The front panel can be locked in two ways: full access and no access, depending on the direction of the keyhole.
Getting Started Front view (with the front panel opened) 11 Front view (with the front panel opened) (2) CD-ROM drive (4) System status indicators (3) Operation buttons (5) Front panel display (6) Card slot (9) Device bay (7) USB 1 connector (10) HDD/LAN status indicators (8) USB 2 connector (1) Front panel Front view of the Micro Tower Type (1) Front panel The front panel can be opened by releasing the key lock, and pushing its upper center (::) and detached by unhooking its hinges.
12 Getting Started Front view (with the front panel opened) Removing the front panel (2) Operation buttons The server has 4 operation buttons on the front panel.
Getting Started Front view (with the front panel opened) 13 Power/ sleep button Press this button to turn on or off the server. ON ... Pressing the button once causes the server to start up. OFF ... Enabling the auto-shutdown function: If you hold your finger continuously for four seconds or more and take your finger away, the OS is shut down and the power supply is turned off. If you take your finger away within four seconds, the power is not turned off. ...
14 Getting Started Front view (with the front panel opened) (3) System status indicators Your server has 4 operating status indicators on the front panel.
Getting Started Front view (with the front panel opened) Indicator Auto Shutdown Status Off 15 Meaning Out of operation Lit green Auto Shutdown function is enabled Auto Shutdown function is ready to start when power switch is turned off Lit amber Auto Shutdown function is out of order - Auto Shutdown is used on Windows NT, Windows 2000 or Linux, and the Auto Shutdown function is not installed - Auto Shutdown is used on Windows NT, Windows 2000 or Linux, the Auto Shutdown function is installed, and set
16 Getting Started Front view (with the front panel opened) (4) Front panel display This server is equipped with a 16-digit/2-line front panel display. The following information is displayed on this panel: 1. System configuration 2. User messages 3. Trouble information 4. Bootup/shutdown messages 1.
Getting Started Front view (with the front panel opened) 17 Two messages can be set by Remote Management and Front Panel Display Setup Tool in the case of a Netware environment. See “System Configuration Setup” on page 138. or the “Harness Eye/web User’s Guide” (on the Documentation CDROM) 3. Trouble information When a problem occurs, the details of the problem and the location where the problem occurred are displayed flashing on the panel.
18 Getting Started Front view (with the front panel opened) At shutdown by auto SD Now shutting down system. Holding down the display change button for at least four seconds displays the user message or system configuration. (5) Card slot The card slot accepts an optional wireless LAN card. (6) USB1 connector Used to connect a USB device. (7) USB2 connector Used to connect a USB device.
Getting Started Front view (with the front panel opened) 19 (9) HDD/LAN status indicators When the device bay accomodates hard disk drives, the status of each hard disk drive is indicated by the HDD status indicators placed below the device bay. The network status of the LAN1 and LAN2 connectors are displayed on the LAN status indicators.
20 Getting Started Front view (with the front panel opened) Indicator LNK 2 (LAN2) Status Meaning Out Network communications (10Mbps or 100Mbps) is not possible. Lit Network communications (10Mbps or 100Mbps) is possible. STS 1 Off (HDD1) No hard disk drive is installed. No data is being read or written. Lit green Data is being read or written. Lit amber Trouble has occurred. Flashing The disk array is being rebuilt. amber PWR 1 Off (HDD1) No hard disk drive is installed.
Getting Started Front view (with the front panel opened) 21 NOTE: When a STS indicator is lit amber, the corresponding hard disk drive may be faulty. If it is found to be defective, replace it. If your system is configured in redundancy (RAID1), you can replace the faulty drive without interrupting the system operation. Shock and vibration might damage hard disk drives, causing the loss or corruption of the data and programs recorded on them. So always handle them carefully.
22 Getting Started Rear view Rear view (1) AC connector (2) Security Loop Rear view of the server (1) AC connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. (2) Security Loop It is possible to attach chains, etc. to prevent the server from theft.
23 Getting Started Rear view I/O connectors Plug the cables of peripheral devices into their respective I/O ports. (8) SCSI connector ( ) (7) External unit control connector ( (1) Mouse connector ( ) (2) Keyboard connector ( ) (4) LAN 2 connector ( (3) LAN 1 connector ( (5) RGB connector ( ) (6) Serial connector ( ) Ether Ether ) 2) 1) I/O connectors (1) Mouse connector ( ) Used to connect the PS/2 mouse. (2) Keyboard connector ( ) Used to connect the PS/2 keyboard.
24 Getting Started Rear view Expansion slot The server has 1 expansion slot for expansion cards: 64 bit/66 MHz PCI slot.
Getting Started Inside the server 25 Inside the server (7) IDE HDD Cage (2) SCSI riser card (4) CPU sockets (6) Expansion slot (3) Cooling fans (1) Motherboard (5) Memory slots (8) Board for wireless card Inside the server (1) Motherboard The main board can contain 2 CPU modules and 3 memory modules at the maximum. (2) SCSI riser card The SCSI riser card has 1 PCI expansion slot (half length cards only).
26 Getting Started Connecting peripheral devices (3) Cooling fans The server contains two cooling fans. (4) CPU sockets Used to mount CPU modules. See “CPU module” on page 78. (5) Memory slots Used to mount up to 3 memory modules to expand the server’s RAM (Random Access Memory). See “Memory module” on page 72. (6) Expansion slot Used to mount expansion cards. A 64 bit/66 MHz PCI card of card length 194 mm or less can be added on to the riser card. The slot is compliant with PCI 2.2 standard.
Getting Started Connecting peripheral devices 27 Connect peripheral devices to the server, according to the following procedure: NOTE: USB devices can be connected while the server is running. 1 Make sure that all the power buttons of the server and external units are turned off. 2 If the power cables of the server and external units are connected to an AC outlet, pull the plug of the power cable out of the AC outlet.
28 Getting Started Connecting peripheral devices Connecting peripheral devices (Rear view) 4 If a connector is provided with screws for securing connection, tighten the screws without fail. 5 After making sure that all the peripheral units are properly connected, plug the power cables of the server and peripheral units into AC outlets. WARNING: When connecting optional units, be sure to use genuine Toshiba parts or those recommended by Toshiba.
Getting Started Connecting peripheral devices 29 NOTE: When connecting and disconnecting an interface cable, be sure to hold the cable connector. Some articles and interface cables of other brands cannot be connected to this server as external units and connecting cables. Before purchasing a peripheral unit, ask the manufacturer or sales office of the article about its compatibility to this server. When connecting peripheral units, see to instructions of respective units together with this manual.
30 Getting Started Maintenance Maintenance Maintenance of the server If the outside of the server is dirty or stained, gently wipe it off with a soft cloth. If it is severely dirty, moisten the soft cloth with water and lightly wipe off the dirt.. If benzene, thinner or a similar substances is used for cleaning or a chemical such as an insecticide is applied onto the surface, the server may be deformed or discolored. Do not subject the server to a strong shock or vibration.
Getting Started Connecting the power cable 31 Connecting the power cable NOTE: Use of an uninterruptible power supply (UPS) is recommended to avoid losing data because of unexpected shutdown or power failure. After connection of peripheral devices is complete, connect the power cable to this server following the procedure mentioned below. 1 Connect the power cable to the connector on the back of the server.
32 Getting Started Connecting the power cable WARNING: Be sure to use the power cable supplied with the server. Using another power cable may cause an outbreak of fire. Plug the power cable into an AC outlet with a ground line. If the power cable is plugged into an unspecified AC outlet, it may cause an outbreak of fire or electric shock. When disconnecting the power cable from the AC outlet, don’t pull the cord but hold the plug.
Getting Started Switching on the server 33 Switching on the server NOTE: When turning on the server again, turn on the power button at least 10 seconds after the power button was last turned off. If the server is switched on again within 10 seconds after it was switched off last, it may cause malfunction of the server or trouble with it.
34 Getting Started POST (Power On Self-Test) Turning on the server by the “Remote Management” function This server has the function that the server can be started up by a client who is in connection with the network interface. Installing HarnessEye/web contained in the Toshiba Server Setup Tool on the client enables packets to be sent from the client to start up the server.
Getting Started Starting up the system 35 Starting up the system The “Toshiba Server Setup Tool” is to be used for almost all of setup procedures for this system, such as installing the operating system (OS), making backup floppy disks etc. The “Toshiba Server Setup Tool” is comprised of the “Toshiba Server Setup Tool CD-ROM” and “Startup Disk,” and the latter (Startup Disk) is used to start up the server.
36 Getting Started Starting up the system Starting up by the hard disk drive unit (in the case the OS has been installed) To start up the server from the hard disk drive unit, proceed as follows: 1 Make sure that neither the floppy disk nor CD-ROM that is capable of starting up the server is in either drive unit. 2 Switch on the power/sleep button. NOTE: The CD-ROM can be ejected from the CD-ROM drive unit only when the system is on.
Getting Started BIOS setup 37 Starting up by the CD-ROM To start up the server from the CD-ROM, proceed as follows: 1 Make sure that no floppy disk is placed in the floppy disk drive. 2 Switch on the power/sleep button. 3 Immediately after switching on the power/sleep button, press the eject button of the CD-ROM drive unit and place the start up CD-ROM in the drive. NOTE: The CD-ROM can be ejected from the CD-ROM drive unit only when the system is on.
38 Getting Started Making a floppy disk Making a floppy disk The server setup support software “Toshiba Server Setup Tool” has the added function of making system backup floppy disks. Such disks store important driver data and utilities etc. It is always recommended to make/store system backup floppy disks for future use.
Getting Started Setup of system configuration 39 Setup of system configuration If the system is used as it was configured at the factory, it was properly set up before shipment. However, if something optional is added to the system after shipment, or it is desired to change the operating condition properly for use, it is required to set up the system once again. There are the following utilities prepared for setup of the system configuration. See “System Configuration Setup” on page 138.
40 Getting Started Setup of disk array (RAID) Setup of disk array (RAID) When an IDE RAID or RAID controller is additionally installed in the system after purchase, or if it is built in the server before delivery, it is required to set the disk array (RAID).
Getting Started Installing software 41 Installing software Once the system is completely set up, install the OS (operating system), and the accessory software used for the server monitor function (Integrated server management tool) supplied with the server and the RAID controller software. See “User’s Manual for the Operating System” and “Toshiba Server Setup Tool User’s Guide” (on the Documentation CDROM).
42 Getting Started Switching off the server Switching off the server The method for switching off the server varies depending on the operating system used. Check the operating system and switch the server off using the normal method or use the automatic shutdown function. Every time the server is to be switched off, use only one of the methods mentioned above. Using both methods simultaneously, will cause the server to fail during its normal shutdown operation.
Getting Started Switching off the server 43 Switch the server off using the automatic shutdown function according to the following procedure: 1 Execute the specified shut down process for the application software running on the operating system.Be sure to save the data used on the application software before quitting. NOTE: As the server is switched off by the automatic shutdown function or ACPI function, the application software currently in use is closed and unsaved data is deleted.
44 Getting Started Switching off the server Notes on using of the automatic shutdown function Hints on operation of the power/sleep button If the power/sleep button is used during the operation of the operating system, during the shutdown operation or if the power/sleep button is operated in a wrong way, it may cause malfunction of the server.
Getting Started Switching off the server 45 Logon by a user without shutdown rights If an unauthorized user logs on, the automatic shutdown function with the power/sleep button is disabled. If the server enters into this mode, log on to the server as the system administrator and then carry out the normal manual shutdown operation and switch off the power. The automatic shutdown function recovers as the system is restarted.
46 Getting Started Switching off the server Abnormal system shutdown If the server is not shutdown using the normal method, the system can be forcibly stopped. However, this operation deletes unsaved data. To shut down the system forcibly, press the reset button. NOTE: If the server was forcibly shutdown, unplug the power cable from the AC outlet once and plug it in again.
Chapter 2 Before starting operation ............................................................ 48 Removing and replacing the server panels .............................. 54 Power Supply Unit ..................................................................... 69 Memory module ......................................................................... 72 CPU module ................................................................................ 78 Internal battery .........................................
Installing and Removing Hardware This chapter explains the different methods used to install and remove optional devices. Before starting operation Install optional devices before setting up the server.
Installing and Removing Hardware Before starting operation Before starting operation WARNING: When installing an optional device, be sure to use genuine Toshiba parts or those recommended by Toshiba. If any other device is used, it may result in a fire hazard. For more information about optional devices, consult an authorized MAGNIA service provider. Do not touch any part irrelevant to the installation work. The server contains many high-tension parts, which if touched may cause an electric shock.
50 Installing and Removing Hardware Before starting operation The installation or removal of an optional device should be carried out at ambient temperatures of 50 to 95°F (10 to 35°C) for Micro Tower Types, or 50 to 89°F (10 to 32°C) for Rack Types, and at ambient humidity of 30 to 80%. Avoid a place where the temperature may change sharply because it may cause condensation inside the equipment. Don't install/remove an optional device in a static environment (e.g. on a carpet).
Installing and Removing Hardware Before starting operation When connecting a cable to the server, pay careful attention to the shape of the connector. If a incorrect connector is forcibly connected, it may bend or damage the connector pins. If the cable connector has thumb screws for fastening, tighten them to secure the connection. Carefully handle options whose boards are not covered such as expansion cards because they are easily affected by static electricity.
52 Installing and Removing Hardware Before starting operation Installing/removing an optional device WARNING: When installing a peripheral unit, don't open any part other than those specified by the instructions. If an irrelevant part is opened, it may cause an electric shock. Install or remove an optional device following the procedure mentioned below: 1 Carefully read the precautions mentioned in this chapter (Before starting operation) and check all the items.
Installing and Removing Hardware Before starting operation 53 8 Attach the server panels and outer covers to the server. In case of the Rack Type, fit the panels to the server before mounting it on the rack. 9 Connect the peripheral units and switch them on. 10 Plug the server's power cable connector into an AC outlet (or UPS) and then switch on the server. Some optional devices need to be setup with jumper switches and DIP switches. See “BIOS setup utility” on page 39.
54 Installing and Removing Hardware Removing and replacing the server panels Removing and replacing the server panels To mount optional devices inside the server, you need to remove the top panel depending on the option you are mounting. CAUTION: When sliding a server panel, be careful not to catch you finger between it and the server. The panel might cause injury.
Installing and Removing Hardware Removing and replacing the server panels 55 4 Remove the front panel. See “Front panel” on page 11 5 Remove nine screws and the top panel. Removing the top panel Replacing the top panels (for Micro Tower Types) Follow these steps to replace the top panel: 1 Replace the top panel to the server carefully so that it does not catch any cable. 2 Fix the top panel using nine screws. 3 Fix the outer cover (upper and bottom) using eight screws. 4 Attach the front panel.
56 Installing and Removing Hardware Removing and replacing the server panels When using a Rack Type Rack assembly procedure Quantity check Rack Mount Tray No.
57 Installing and Removing Hardware Removing and replacing the server panels Parts provided with the rack blank module 19 BLANK BRACKET 1 20 FRONT BRACKET 1 21 FLAT SCREW(GRIP) 3 1 Decide on where to assemble the server.
58 Installing and Removing Hardware Removing and replacing the server panels 2 Temporarily fasten Rail R to the posts on the left and right of the rack rear, and Rail F (L) and Rail F (R) to the posts on the left and right at the front with Screws (M6). Rail R Rail F WD (L) Screws (M6) Temporarily fasten the Rails 3 Fix Rail R on the left and right, Rail F (L) and Rail F (R) with two Screws (M5).
Installing and Removing Hardware Removing and replacing the server panels 59 4 Attach Pin Catch Tray to Rail F (L) and Rail F (R) with two Screws (M5). Pin Catch Tray Screws (M5) Attach Pin Catch Tray 5 Attach Washer, Spring Washer and Guide Pin (M6) at two locations to the Base assembly.
60 Installing and Removing Hardware Removing and replacing the server panels 6 Insert the Base Assembly into the Rail, and insert Guide Pin (M6) into the Pin Catch Tray. Pin Catch Tray Guide Pin Insert the Base Assembly 7 Attach the Support Bracket (L) and Support Bracket (R) on the Base Assembly and fix them with two screws (M5).
Installing and Removing Hardware Removing and replacing the server panels 61 8 Fix the Base Assembly to the rack with the claw screws on the front. Claw screw Fix the Base Assembly 9 Tighten the eight screws temporarily fastened in step 2.
62 Installing and Removing Hardware Removing and replacing the server panels 10 Attach Washer, Spring Washer and Guide Pin (M6) on the back. Washer Spring Washer Guide Pin Attaching the Guide Pin 11 Attach the Front Bracket (L) or Front Bracket (R) to the server bay with Screws (M3). Screws (M3) Front Bracket Attach the Front Bracket When you insert the server bay into the right of the rack, attach Front Bracket (R).
Installing and Removing Hardware Removing and replacing the server panels 63 12 Place the server bay on the Base Assembly and insert. Insert the server bay 13 Loosen the claw screw to draw out the Base Assembly by about 100 mm. Claw screw Drawing out the Base Assembly When turning the claw screws, remove the front panel so that you do not catch your fingers.
64 Installing and Removing Hardware Removing and replacing the server panels 14 Fix the Base Assembly to the server housing with a screw (M3). Screw (M3) Fixing the Server Housing When using the rack blank module, attach the Front Bracket to the Blank Bracket using the two flat screws, and place both on the Base Assembly and fix with two flat screws.
Installing and Removing Hardware Removing and replacing the server panels 65 15 Insert the entire Base Assembly into the rack. Inserting Into Rack Blank Module 16 Fix the housing on the left and right with the claw screws of Front Bracket (L) and Front Bracket (R). Claw screw Fix the housing on the left and right When turning the claw screws, remove the front panel so that you do not catch your fingers.
66 Installing and Removing Hardware Removing and replacing the server panels Sliding the server out of or into the rack When installing an optional device to a Rack Type server, follow the instructions mentioned. WARNING: Don't slide more than two Rack Mount Trays out of the rack at the same time. If two or more units are pulled out of the rack, the rack may become unstable and topple down.
Installing and Removing Hardware Removing and replacing the server panels 67 Sliding the server (Rack Type) out of the rack Slide the server out of the rack in the procedure described below, while referring to “Before starting operation” on page 48. 1 If the server is running, shut it down and switch off the power. 2 Switch off all the peripheral units connected with the server. 3 Unplug the power cable of the server from the AC outlet or UPS (uninterruptible power supply).
68 Installing and Removing Hardware Removing and replacing the server panels Screw (M3) Removing the screw 7 Slide the server out of the rack. Sliding the server (Rack Type) into the rack 1 Gently slide the server into the rack, according to the rack assembly procedure step 10 - 15. 2 When it is located in place, fix the server with four screws. When turning the claw screws, remove the front panel so that you do not catch your fingers. 3 Connect the cables disconnected.
Installing and Removing Hardware Power Supply Unit 69 Power Supply Unit Removing the power supply unit The power supply unit must be removed and attached when replacing or adding on memory or batteries. NOTE: The installation and replacement of the power supply unit requires special technology and knowledge. If you have no experience in installing the power supply unit or if you need assistance, consult your authorized MAGNIA service provider.
70 Installing and Removing Hardware Power Supply Unit 5 Disconnect the power cable and signal cable. Disconnecting the cables Installing the power supply unit NOTE: The installation and replacement of the power supply unit requires special technology and knowledge. If you have no experience in installing the power supply unit or if you need assistance, consult your authorized MAGNIA service provider.
Installing and Removing Hardware Power Supply Unit 71 4 Connect the power cable and signal cable. Connecting the cables 5 Install the power supply unit, slide back slightly and fix it with six screws. Installing the power supply unit 6 Attach the server panels and outer covers.
72 Installing and Removing Hardware Memory module Memory module Your server can accommodate a maximum of three 128-MB, 256MB, 512-MB or 1-GB DIMMs (Dual In-line Memory Modules) with the ECC (Error Correction Control), which operate at a system bus clock frequency of 133 MHz. See “Specifications” on page 216. The memory can be expanded to a maximum of 3 GB by installing additional memory modules with up to two different capacities. The memory controller is conformable to the SDRAM.
Installing and Removing Hardware Memory module Slot1 Slot2 Unit : MB Total Slot3 128 512 128 1024 256 256 512 512 73 512 1152 1152 512 1024 1024 1024 1024 256 256 256 768 128 128 512 768 256 512 128 256 128 512 128 128 256 256 768 256 640 256 512 128 128 128 256 256 128 512 512 512 128 640 128 384 384 256 128 256 128
74 Installing and Removing Hardware Memory module Memory slot 3 Memory slot 2 Memory slot 1 Memory slots WARNING: When installing a peripheral unit, don't open any part other than those specified by the instructions. Touching unspecified parts may cause an electric shock. CAUTION: Do not install or remove additional memory modules when the server has just been switched off. This is to avoid burning the hands from the heat built-up from the extension memory sockets and their peripheral during operation.
Installing and Removing Hardware Memory module 75 Before installing an additional memory module, carefully read “Before starting operation” on page 48 and proceed as follows: 1 If the server is in operation, first shut it down and switch off the power supply to it. 2 Unplug the power cable from the AC outlet. NOTE: Installing a memory module while the server is still operational could cause damage to the server or the memory module. 3 Remove the outer covers and server panels from the server.
76 Installing and Removing Hardware Memory module 6 Insert the memory module into the proper memory slot, paying attention to the position of each notch on the memory module. Insert the memory module until it is locked by the hooks on both sides. Installing a memory module 7 Install the power supply unit. See “Power Supply Unit” on page 69 8 Attach the server panels and outer covers. 9 Connect the power cable of the server to the power supply and switch on the server.
Installing and Removing Hardware Memory module 77 Removing a memory module Before removing a memory module, carefully read “Before starting operation” on page 48 and proceed to the job following the procedure mentioned below: 1 If the server is in operation, shut it down and switch off the power. 2 Unplug the power cable from the AC outlet. NOTE: Removing a memory module while the server is still in operation could cause damage to the server and/or the memory module.
78 Installing and Removing Hardware CPU module 6 Install the power supply unit. See “Power Supply Unit” on page 69 7 Fit the server panels and outer covers to the server. 8 Connect the power cable of the server to the power supply and switch on the server CPU module The server is classified into 2 models, each having different CPU clock speeds (866 MHz, 1 GHz). If two processors are installed in your server, the server is transformed into an upgraded version (two CPUs max.).
Installing and Removing Hardware CPU module 79 Installing the CPU module NOTE: The CPU module may be fatally damaged by static electricity because it consists of precise electronic parts. The human body contains static electricity. Therefore, discharge the static electricity before installing the CPU module. Static electricity can be discharged by touching a nearby metallic object with your fingers.
80 Installing and Removing Hardware CPU module Removing the PCI bracket
Installing and Removing Hardware CPU module 81 5 Remove one screw that fix the riser card and remove the riser card. Removing the riser card NOTE: Lift up the riser card with a screwdriver to remove.
82 Installing and Removing Hardware CPU module 6 Remove two screws and the fan duct. Removing the fan duct 7 Raise the lock lever of the expansion CPU socket.
Installing and Removing Hardware CPU module 83 8 Align the CPU pins correctly with the holes in the socket, and insert the CPU module as far as it will go. Inserting the CPU module NOTE: A standard CPU module is installed in the socket 1. To extend the CPU module, install it in the socket 2. 9 Push down the lock lever of the socket until it is hooked securely. Pushing down the lock lever 10 Detach the cover from the thermal seat on the contact surface between the heat sink and the CPU module.
84 Installing and Removing Hardware CPU module 11 Lightly push the heat sink in the direction of the socket, and fix it by engaging the clips with the upper and lower hooks of the socket. Attaching the heat sink Fixing the clips NOTE: Do not push the fin section of heat sink of the CPU module. This may cause the deformation of the heat sink. Push the CPU module until both ends of it become uniformly horizontal on the right and left and confirm that it was inserted completely.
Installing and Removing Hardware CPU module 12 Attach the fan duct and fix it with two screws. Attaching the fan duct 13 Attach the riser card and fix it with one screw. Attaching the riser card 14 Fix the PCI bracket with two screws.
86 Installing and Removing Hardware CPU module Fixing the PCI bracket 15 Install the server panels. 16 Connect the power cable of the server to the power supply and switch on the server. 17 Confirm that the CPU module is recognized properly with the display on the screen. The example below shows a 866 MHz, 2-CPU configuration. Phoenix Server BIOS 4 Release 6.0 Copyright 1985-2000 Phoenix Technologies Ltd. All Rights Reserved BIOS-Version X.
Installing and Removing Hardware CPU module 87 Replacing the CPU module NOTE: The CPU module may be fatally damaged by static electricity because it consists of precise electronic parts. The human body contains static electricity. Therefore, discharge the static electricity before installing the CPU module. Static electricity can be discharged by only touching a nearby metallic object with your fingers.
88 Installing and Removing Hardware CPU module Removing the PCI bracket 5 Remove one screw that fix the riser card, and remove the riser card.
Installing and Removing Hardware CPU module 89 NOTE: Lift up the riser card with a screwdriver to remove. 6 Remove two screws and the fan duct. Removing the fan duct. 7 Release the clips that secure the heat sink for the CPU module to be removed, and remove the heat sink. The heat sink is fixed with clips that are engaged with the upper and lower hooks of the socket. To disengage each clip from the hook, lightly press the clip.
90 Installing and Removing Hardware CPU module Releasing the clips Removing the heat sink 8 Raise the lock levers of the socket in which the CPU module you want to remove is mounted.
Installing and Removing Hardware CPU module 91 9 Remove the CPU module. Removing the CPU module 10 Install a new CPU module following the same procedure as for extension modules. NOTE: Do not push the fin section of heat sink of the CPU module. This may cause deformation of the heat sink. Push the CPU module until both ends of it become horizontal on the left and right sides, and confirm that it was inserted completely. 11 Install the fan duct and fix it with two screws.
92 Installing and Removing Hardware CPU module 12 Install the riser card on the motherboard and fix it with one screw. Installing the PCI riser card 13 Attach the PCI bracket with two screws. Fixing the PCI bracket 14 Install the server panels. 15 Connect the power cable of the server to the power supply and switch on the server. 16 Confirm that the replaced CPU module is recognized properly with the display on the screen.
Installing and Removing Hardware CPU module 93 The example below shows a 866 MHz, 2-CPU configuration. Phoenix Server BIOS 4 Release 6.0 Copyright 1985-2000 Phoenix Technologies Ltd. All Rights Reserved BIOS-Version X.XX CPU=2 Pentium(R)III Processor 866MHz XXXK System RAM Passed XXXM Extended RAM Passed NOTE: When a CPU module is extended, the operating system (OS) may have to be reinstalled to recognize a new CPU module. The CPU modules with different CPU speeds cannot be used together.
94 Installing and Removing Hardware Internal battery Internal battery This server has an internal battery to store the information on a timer and system configuration. The replacement of a battery requires special technology and knowledge. Toshiba recommends that you ask your authorized MAGNIA service provider to replace the internal battery. CAUTION: Observe the following when handling a lithium battery. A lithium battery is used for the internal battery of the server.
Installing and Removing Hardware Internal battery 95 Replacing the internal battery Replace the battery in the procedure described below, while referring to “Before starting operation” on page 48: 1 Write down the system configuration information. 2 Shut down and switch off your server. 3 Unplug the power cable. NOTE: Don't replace the battery when your server is on, otherwise your server or the internal battery could be damaged. 4 Remove the server panels.
96 Installing and Removing Hardware Internal battery 7 Put your fingers below the battery, and pull it up. Removing the battery 8 Install a new battery with polarity (+) up.
Installing and Removing Hardware Internal battery 97 9 Install the board for the wireless card and fix it with four screws. Installing the board for the wireless card 10 Install the power supply unit. 11 Install the server panels. 12 Connect the power cable of the server to the power supply, and switch on the server. 13 Set the server according to the System Time, System Date and system configuration information that was written down in advance.
98 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– Hard Disk Drive (HDD) –IDE HDD– Slot numbers (of 1 to 2 from bottom) are assigned to each slot of a hard disk drive. Installing the hard disk drive NOTE: The installation and replacement of a hard disk drive requires special technology or knowledge. If you have no experience in installing a hard disk drive or if you need assistance, consult your authorized MAGNIA service provider.
Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– 99 5 Pull out the HDD slot spacer that was partially extracted. 6 Push the hard disk drive completely into the slot where you want to mount it. Installing the hard disk drive 7 Close the detachable lever and fix it. Push in the detachable lever so that the hard disk drive is firmly fixed. Fixing the detachable lever 8 Attach the front panel.
100 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– 9 Connect the power cable of the server to the power supply, and switch on the server. NOTE: The setting of an operating system (OS) or application software may have to be changed after adding or removing a hard disk drive.
Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– 101 2 Confirm the position of a faulty device. The STS indicator of the faulty device is lit amber. CAUTION: The hard disk drive generates heat when in use. To avoid burns, hold the disk tray when removing the hard disk drive. 3 Tilt over the detachable lever of the slot which holds a defective hard disk drive, by pulling its knob toward you.
102 Installing and Removing Hardware Hard Disk Drive (HDD) –IDE HDD– Pulling out the hard disk drive 5 Install a new hard disk drive in the same procedure as for extension. See “Installing the hard disk drive” on page 98. 6 After a short time, confirm that the PWR indicator lights up. 7 Attach the front panel. 8 Recover (rebuild) the disk.
Installing and Removing Hardware Expansion cards 103 Expansion cards One PCI expansion card can be installed in the server. PCI slot Expansion slots Restrictions on PCI expansion cards The PCI slot support 64 bit/66 MHz and less than 194mm long PCI cards.
104 Installing and Removing Hardware Expansion cards Installing the SCSI riser card WARNING: Do not touch any parts except those necessary for installing the device. There are many high-voltage parts that may cause an electric shock. When installing or removing the expansion card, shut the server down, switch off the power, and pull out the power plug from the wall outlet. This may cause an electric shock. CAUTION: It is advisable to wear gloves when installing or removing the expansion card.
Installing and Removing Hardware Expansion cards 5 Install the SCSI cable. Installing the SCSI cable 6 Connect the SCSI cable of the SCSI riser card.
106 Installing and Removing Hardware Expansion cards 7 Insert the expansion card in the SCSI riser card. Inserting the expansion card 8 Install the SCSI riser card on the motherboard and fix it by one screw.
Installing and Removing Hardware Expansion cards 107 9 Fix the PCI bracket with two screws. Fixing the PCI bracket 10 Install the power supply unit. 11 Install the server panels. 12 Connect the power cable of the server to the power supply, switch on the server. To remove the SCSI Riser card, please reverse the above procedure.
108 Installing and Removing Hardware Expansion cards
Chapter 3 Types of External Unit ............................................................. 110 Front view of the External Hard Drive Unit Z1 (with the front panel closed) .............................................................................. 111 Front view of the External Hard Drive Unit Z1 (with the front panel opened) ............................................................................ 112 Rear view of the External Hard Drive Unit Z1 .....................
External Unit Setup Types of External Unit The following two types of External Unit (sold separately) are available for this server: c External Hard Drive Unit Z1 c External Device Bay Unit Z1 110
External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel closed) 111 Front view of the External Hard Drive Unit Z1 (with the front panel closed) Power indicator Fault indicator Key lock Front view with the front panel closed Key lock The front panel can be locked at two levels: full access and no access, depending on the direction of the keyhole.
112 External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) Front view of the External Hard Drive Unit Z1 (with the front panel opened) (3) System status indicator (4) Disk status indicator (2) Power switch HDD 4 Device bay HDD 2 HDD 1 HDD 3 (1) Front panel Front view of the Micro Tower Type (1) Front panel The front panel can be opened by releasing the key lock, pushing its upper center (::) and detached by unhooking its hinges.
External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) 113 (2) Power button The server has an power button on the front panel. Power button Power button Power button Press this button to forcibly turn on or off the External Hard Drive Unit Z1. ON ... Pressing the button once causes the unit to start up. OFF ... Pressing and holding down the button causes the unit to turn off.
114 External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) (3) System status indicators This server has 2 operating status indicators on the front panel.
External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) 115 (4) HDD status indicators If the device bay accommodates hard disk drives, the status of each hard disk drive is indicated by the power indicator and the status indicator located above the device bay.
116 External Unit Setup Front view of the External Hard Drive Unit Z1 (with the front panel opened) NOTE: When a status indicator is lit amber, the corresponding hard disk drive may be faulty. If it is found to be defective, replace it. If your system has a built-in RAID controller, you can replace the faulty drive without interrupting the system operation. Shock and vibration might damage hard disk drives, causing the loss or corruption of the data and programs recorded on them.
External Unit Setup Rear view of the External Hard Drive Unit Z1 117 Rear view of the External Hard Drive Unit Z1 AC power connector Rear view of the External Hard Drive Unit Z1 AC power connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. I/O connectors Plug the cables of peripheral devices into their respective I/O ports.
118 External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- Installing and Removing Hard Disk Drive (HDD) -SCSI HDDThe slot numbers (of 1 to 4) are assigned to each slot of a hard disk drive. Read “Before starting operation” on page 48 before installing additional hard disk drives, and mount them in the slots, starting from the bottom left. Installing the hard disk drive NOTE: The installation and replacement of a hard disk drive requires special technology or knowledge.
External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 119 2 Tilt over the detachable lever of the slot where you want to install a hard disk drive, by pulling its knob toward you. Pulling the detachable lever toward you 3 Pull out the HDD slot spacer that was partially extracted. 4 Push the hard disk drive completely into the slot where you want to mount it.
120 External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 5 Close the detachable lever and fix it. Push in the detachable lever so that the hard disk drive is firmly fixed. Fixing the detachable lever 6 Attach the front panel. NOTE: The setting of an operating system (OS) or application software may have to be changed when the hard disk drive is extended.
External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 121 NOTE: Hard disk drives cannot be replaced while the system is in operation, unless a RAID controller is installed. Be sure to unplug the power cable before proceeding to replacement. By setting a spare disk (hot spare), a disk array can be automatically recovered using the spare disk when a hard disk drive fails. See “MegaRAID Software Guide.
122 External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- Removing the front panel See “Front panel” on page 11. 2 Confirm the position of a faulty disk. The STATUS indicator ( ) of a faulty disk lights amber. CAUTION: The hard disk drive generates heat when in use. To avoid burns, hold the disk tray when removing the hard disk drive. 3 Tilt over the detachable lever of the slot which holds a defective hard disk drive, by pulling its knob toward you.
External Unit Setup Installing and Removing Hard Disk Drive (HDD) -SCSI HDD- 123 NOTE: Before pulling out the hard disk drive, make sure that it is faulty. If a normally operating disk is pulled out by mistake, it may damage the server or destroy and lose important programs or data. 4 While holding the disk tray, carefully remove the hard disk drive that is pulled out halfway. Pulling out the hard disk drive 5 Install a new hard disk drive in the same procedure as for extension.
124 External Unit Setup Setup of disk array (RAID) NOTE: If the server uses a RAID controller for redundancy, the operation is continued by a spare disk without stopping the system, even if one of the hard disk drives that configure a disk array fails (downgraded operation). However, if another disk fails, it may destroy and lose important programs or data. Replace the faulty disk by a normal one as quickly as possible, and recover the disk array.
External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel closed) 125 Front view of the External Device Bay Unit Z1 (with the front panel closed) Power indicator Fault indicator Key lock Front view with the front panel closed Key lock The front panel can be locked at two levels: full access and no access, depending on the direction of the keyhole.
126 External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel opened) Front view of the External Device Bay Unit Z1 (with the front panel opened) (3) System status indicator (2) Power switch Device bay (1) Front panel Front view of the Micro Tower Type (1) Front panel The front panel can be opened by releasing the key lock, pushing its upper center (::) and detached by unhooking its hinges. See “Front panel” on page 11.
External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel opened) 127 (2) Power button The server has an power button on the front panel. Power button Power button Power button Press this button to forcibly turn on or off the External Device Bay Unit Z1. ON ... Pressing the button once causes the unit to start up. OFF ... Pressing and holding down the button causes the unit to turn off.
128 External Unit Setup Front view of the External Device Bay Unit Z1 (with the front panel opened) (3) System status indicators This server has 2 operating status indicators on the front panel.
External Unit Setup Rear view of the External Device Bay Unit Z1 129 Rear view of the External Device Bay Unit Z1 AC power connector Rear view of the External Device Bay Unit Z1 AC power connector Used to connect the AC power cable. See “Connecting the power cable” on page 31. I/O connectors Plug the cables of peripheral devices into their respective I/O ports.
130 External Unit Setup Installing SCSI device (2) SCSI connector ( ) Used to connect the System Unit. See “How to connect peripheral devices” on page 26. Installing SCSI device The installation of a SCSI device requires special knowledge or technology. If you have no experience in installing a SCSI device or require assistance, consult your authorized MAGNIA service provider. Terminator The SCSI bus is terminated at the SCSI controller and dedicated External Device Bay Unit Z1.
External Unit Setup Installing SCSI device 131 3 Open the front panel. 4 Remove four screws and remove the outer cover (upper). Removing the outer cover 5 Remove seven screws and remove the top cover.
132 External Unit Setup Installing SCSI device 6 Remove the power and signal cables. When removing the signal cable, disconnect it from the External Device Bay Unit Z1. Removing the cables 7 Remove four screws that fix the SCSI device.
External Unit Setup Installing SCSI device 133 8 Pull out the SCSI device completely. Remove the SCSI device 9 Set the SCSI ID so that it would not be the same as other device. 10 Insert the SCSI device into the unit. 11 Attach the four screws and fix the SCSI device.
134 External Unit Setup Installing SCSI device 12 Connect the power and signal cables. Connecting the cables 13 Attach the top cover and fix it with seven screws.
External Unit Setup How to Connect an External Unit 135 14 Attach the outer cover (upper) and fix it with four screws. Attaching the outer cover 15 Close the front panel. 16 Connect the power cable of the server to the power supply and switch on the server.
136 External Unit Setup How to Connect an External Unit When connecting External Units by External Unit control cables, follow the procedure below.
Chapter 4 BIOS setup utility ..................................................................... 138 SCSI Utility ............................................................................... 150 Remote Management and Front Panel Display Setup Tool 156 Configuring MegaRAID IDE .................................................
System Configuration Setup BIOS setup utility NOTE: The menus shown in this chapter are just examples. The BIOS Setup Utility is a menu type of program designed to verify and modify the basic settings of the motherboard.
System Configuration Setup BIOS setup utility 139 Starting the setup utility The BIOS screen will appear when the server is started. Phoenix BIOS 4.0 Release X.X.X.XX Copyright 1985-2000 Phoenix Technologies Ltd., All Rights Reserved BIOS Version X.
140 System Configuration Setup BIOS setup utility Menu screen The following menu will be displayed when the BIOS Setup Utility is started: PhoenixBIOS Setup Utility Main Advanced Security Boot System Time: System Date: [XX:XX:XX] [XX/XX/XXXX] Primary Master Primary Slave FSB Frequency DRAM Frequency [CD-ROM] [None] [XXXMHz] [XXXMHz] Exit Item Specific Help , or selects field.
System Configuration Setup BIOS setup utility 141 BIOS Setup Utility Keyboard Commands Displays Help. Returns control to the previous screen mode. Specifies a menu or data item. <↑> Returns control to the previous data item. <↓> Advances control to the next data item. <←><→> Specifies a menu. Resets all data settings to defaults (except for the passwords). Saves data settings and exits the BIOS Setup Utility.
142 System Configuration Setup BIOS setup utility Main menu System Time: System Date: [XX:XX:XX] [XX/XX/XXXX] Primary Master Primary Slave FSB Frequency DRAM Frequency [CD-ROM] [None] [XXXMHz] [XXXMHz] Processor Settings Processor 1 Memory Shadow Memory Cache Summary screen AC ON state [Disabled] [Last State] System Memory Extended Memory 640 KB XXXXX KB BIOS Version BMC Version XXX XXX c System Time/System Date Enter the system date and time.
System Configuration Setup BIOS setup utility 143 c DRAM Frequency Displays DRAM Frequency. c Processor Settings Processor 1/Processor 2 Displays Processor speed/ID/Cache memory size. Processor 2 is only displayed when there is a second CPU. c Memory Shadow The following submenu appears: System shadow: Video shadow: System shadow [Enabled] [Enabled] :[Enabled] Do not change this setting. Video shadow :[Enabled] Shadow video BIOS and improves performance. Do not change this setting.
144 System Configuration Setup BIOS setup utility Enables or disables all memory caching. Cache System BIOS area :[Write protect] Controls caching of system BIOS area. Cache Video BIOS area :[Write protect] Controls caching of video BIOS area. Cache Base 0-512k :[Write Back] Controls caching of base memory 0-512k. Cache Base 512k-640k :[Write Back] Controls caching of base memory 512k-640k. Cache Extended Memory area :[Write Back] Controls caching of extended memory. Cache segment, e.g.
System Configuration Setup BIOS setup utility 145 Displays available system memory size. c Extended Memory Displays extended memory size. c BMC Version Displays BMC version. c BIOS Version Displays system BIOS version. Advanced menu This section describes the advanced settings available in the various BIOS Setup Utility menus.
146 System Configuration Setup BIOS setup utility SCSI :[Enabled] Set SCSI riser card setting. LAN :[Enabled] Set on-board LAN setting. PCI Device slot #1 The following submenu appears: PCI Device slot #1: Option ROM Scan: Enable Master: Latency Timer: Option ROM Scan [Enabled] [Enabled] [0040h] :[Enabled] Do not change this setting. Enable Master :[Enabled] Enables selected device as a PCI bus master. Latency Timer :[0040h] Set Latency Timer in Latency Timer PCI Bus.
System Configuration Setup BIOS setup utility 147 The following submenu appears. Serial port A: Serial port A [Auto] :[Auto] Do not change this setting. c PS/2 Mouse :[Auto Detect] Do not change this setting. c Local Bus IDE adapter :[Primary] Set local IDE adapter setting. c Legacy USB support :[Enabled] When Disabled is set, the USB floppy disk drive can no longer be used. Set Enabled. c Large Disk Access Mode :[DOS] Do not change settings values.
148 System Configuration Setup BIOS setup utility Security menu This section describes the security settings available in the BIOS Setup Utility. Supervisor Password is: User Password is: Clear Clear Set Supervisor Password Set User Password [Enter] [Enter] Diskette Access: Password on Boot: [User] [Disabled] c Set Supervisor Password Allows Supervisor Password to be registered, changed, and/or deleted. To delete a password, press with “New Password”.
System Configuration Setup BIOS setup utility 149 Boot menu This section describes the Boot options available in the BIOS Setup Utility. This menu allows you to set the sequence in which the operating system searches devices for the boot files. Do not change these settings. +Removable Devices +Hard Drive CD-ROM Drive Intel(R)Boot Agent Version X.X.XX Intel(R)Boot Agent Version X.X.XX c +Removable Devices Specifies the boot sequence for the floppy disk drive and other removable storage devices.
150 System Configuration Setup SCSI Utility Exit menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes c Exit Saving Changes Saves changes and restarts the system. Performs the same function as pressing the F10 key. c Exit Discarding Changes Discards all recent configuration changes, then restarts the server. c Load Setup Defaults Resets all setup options to their default values, except for passwords. Performs the same function as pressing the F9 key.
System Configuration Setup SCSI Utility 151 Starting the SCSI Utility When the server is turned on or restarted, the monitor displays the onboard SCSI BIOS initialize message shown below. The display differs based on the type of SCSI device installed in the server. Adaptec AIC-7892 SCSI BIOS vX.XX (C)1998 Adaptec, Inc. All Rights Reserved.
152 System Configuration Setup SCSI Utility Menu configuration When the SCSI Utility starts, the monitor enters the following main menu display mode: Adaptec AIC-7892 < SCSISelect (TM) > Utility vX.XX AIC-7892 at Bus:02h Device:0Fh Would you like to configure the host adapter, or run the SCSI disk Utilities? Select the operation and press Press to switch between color and monochrome modes.
System Configuration Setup SCSI Utility 153 Changing SCSI Device Settings 1 Using the arrow keys (<↑><↓>), select the desired item then press the key. The submenu or selection menu corresponding to the selected item appears. 2 Make any necessary changes then save the changes. 3 Select Exit this Menu to exit the submenu. Setting Devices Select Configure/View Host Adapter Setting in the main menu in the device setting screen mode to display the Adaptec Utility.
154 System Configuration Setup SCSI Utility c Host Adapter SCSI Termination : Enabled Specifies whether the SCSI bus is to be terminated using the SCSI host adapter. Do not change this setting. c Boot Device Options Specifies the SCSI device from which the system is to be booted. c Boot SCSI ID :0 Selects the SCSI ID of the device which boots the system. Do not change this setting. c Boot LUN Number :0 Selects the LUN of the device which boots the system. Do not change this setting.
System Configuration Setup SCSI Utility 155 Specifies whether logical unit numbers are supported. c Include in BIOS Scan : Yes Specifies whether the device is to be scanned when SCSI BIOS starts. c Advanced Configuration Options Sets up detailed data on the SCSI controller. c Reset SCSI Bus at IC Initialization : Enabled Specifies whether or not to reset the SCSI bus during the SCSI controller resetting process.
156 System Configuration Setup Remote Management and Front Panel Display Setup Tool Remote Management and Front Panel Display Setup Tool The Remote Management and Front Panel Display Setup Tool is used for setting/updating information for enabling remote management on the NetWare environment, and for setting display characters on the front panel display. When using Remote Management and Front Panel Display Setup Tool, create a floppy disk from the Toshiba Server Setup Tool.
System Configuration Setup Remote Management and Front Panel Display Setup Tool 157 c [To set up the IP address] 1 When the menu appears, select [1] or [2]. The currently held information appears as follows, and the system waits for entry of the new update values. *** Setup LANx IP Address *** Current LANx IP Address = nnn.nnn.nnn.nnn Change LANx IP Address ? [y/n] Current LANx IP Address >> nnn.nnn.nnn.nnn Please Input (xxx.xxx.xxx.
158 System Configuration Setup Remote Management and Front Panel Display Setup Tool The currently held information appears as follows, and the system waits for entry of the new update values. *** Setup LANx Subnet Mask *** Current LANx Subnet Mask = nnn.nnn.nnn.nnn Change LANx Subnet Mask ? [y/n] Current LANx Subnet Mask >> nnn.nnn.nnn.nnn Please Input (xxx.xxx.xxx.
System Configuration Setup Remote Management and Front Panel Display Setup Tool 159 The following screen appears. TOSHIBA Front Panel Display Setup Tool version X.XX COPYRIGHT TOSHIBA CORPORATION 2001. ALL RIGHTS RESERVED. * Current message USER1 LINE1 > USER1 LINE2 > USER2 LINE1 > USER2 LINE2 > * Please select the message to be set [1].USER1 message [2].USER2 message [Esc].Escape > 2 Next, select the messages to be set. To exit, press the key. [1] key : Set USER1 messages.
160 System Configuration Setup Configuring MegaRAID IDE Configuring MegaRAID IDE Configuring MegaRAID IDE This section explains how to: c configure MegaRAID IDE and arrays c assign RAID levels c plan the array configuration c optimize storage c use the MegaRAID IDE Setup Utility Configuring Arrays Organize the physical disk drives in arrays after the drives are connected to MegaRAID IDE. Each array can consist of one to two physical disk drives.
System Configuration Setup Configuring MegaRAID IDE 161 RAID Level Minimum Number of Physical Drives Maximum Number of Physical Drives 0 One Two 1 Two Two Selecting a RAID Level To ensure the best performance, you should select the optimal RAID level when you create a system drive.
162 System Configuration Setup Configuring MegaRAID IDE 1 Press the + keys to run the MegaRAID IDE Manager. 2 Define and configure one or more logical drives. 3 Create and configure one or more system drives (logical drives). Select the RAID level, write cache policy, virus protection, and DMA transfers. 4 Save the configuration. 5 Initialize the system drives. After initialization, you can install the operating system.
System Configuration Setup Configuring MegaRAID IDE 163 Using the MegaRAID IDE Setup Utility Setup window The Setup window has three sections: c array information c physical drive information c help information Only the Array Information window and Physical Drives Information window are active. The Array Information window is editable. The Physical Drives Information window is not editable. To access this screen, press the + keys during bootup.
164 System Configuration Setup Configuring MegaRAID IDE c Drive numbers of the physical drives included in the array c Stripe size (32 KB to 4 MB) which is valid for Stripe configu- rations only c Whether the system is bootable from one of the configured arrays c Build Array function, which is valid for Mirror array. This option is used to build one drive from another. Physical Drive Information This section displays all the physical drives connected to the IDE channels and their properties.
System Configuration Setup Configuring MegaRAID IDE 165 c Boot sector virus protection c DMA transfers c Enable / Disable Buzzer NOTE: These options apply to all drives attached to MegaRAID IDE. Help section The Help section of the Setup window screen displays hints on available options. The Help section also provides a list of keys that you can use to perform tasks, such as auto configuring, creating or deleting an array.
166 System Configuration Setup Configuring MegaRAID IDE Create Array (F4) Press the key to create a disk array. When you create an array, a default array template is created. You must edit the array properties to complete the array creation. Use arrow navigation keys to highlight a property field and press to edit that property. See the following section for information about setting each property field. Array Type By default an array is created in stripe mode.
System Configuration Setup Configuring MegaRAID IDE 167 DRIVE SELECTION BOX [ ] Cntlr 0-Primary Master [ ] Cntlr 0-Secondary Master Use the arrow navigation keys and press the Spacebar to select or deselect the drive or drives to be part of the array. Press when done. If you select mirror mode as the array type, you must select two drives to be in the array. This pop-up window will appear only when configuring RAID 0 (Stripe) and RAID 1 (Mirror) arrays.
168 System Configuration Setup Configuring MegaRAID IDE Bootable This determines which of the configured arrays should be used for booting the system when MegaRAID IDE is selected as the boot device. The options are Yes or No. BOOT OPTION YES NO You can select the boot device from the system BIOS setup. Only one array is allowed to be bootable in a system. Drive Size This field cannot be edited. It displays the size of the array.
System Configuration Setup Configuring MegaRAID IDE 169 Delete Array (F5) Press the key to delete a currently configured array. Use arrow keys to go over to the array you want to delete and then press . CAUTION: Use this option with caution. When you delete an array, you lose the array configuration and the data saved in the array. Restore Old Configuration (F6) Press the to restore the configuration that was there before you entered the MegaRAID IDE setup utility.
170 System Configuration Setup Configuring MegaRAID IDE Save and Exit (F10) When you have completed the array configuration, press to save the configuration and exit. If you do not want to save the configuration or any changes that you have made, press the key. Subsequent message boxes display for confirmation; respond to them appropriately. Note that when a new array is configured, its partition record is invalidated.
Chapter 5 Windows® NT Server 4.0 ....................................................... 172 Windows® 2000 Server ........................................................... 173 NetWare ..................................................................................... 178 HarnessEye/web ....................................................................... 191 AFT, ALB and IPSec functions .............................................. 192 Auto-shutdown function ........................................
Installing Software Windows NT® Server 4.0 You can install Windows NT on your server automatically using the Toshiba Server Setup Tool. See “Toshiba Server Setup Tool User's Guide“ for the procedure of the automatic installation. Setting the motherboard Before proceeding to the installation of Windows NT, start the BIOS Setup Utility on your system, and specify “WinNT2K” under “Installed O/S” in the Advanced menu. Note that selecting “Other” from this menu could cause your system to malfunction.
Installing Software Windows® 2000 Server 173 Windows® 2000 Server You can install Windows 2000 Server on your server in two different ways: installing it automatically using the Toshiba Server Setup Tool or installing it manually, by following the normal installation steps set for Windows 2000. This section explains how to install Windows 2000 manually. See the “Toshiba Server Setup Tool User's Guide” (on the Documentation CD-ROM) for the procedure of the automatic installation.
174 Installing Software Windows® 2000 Server Selecting the disk driver Selecting the IDE CD-ROM Controller driver Use the driver contained on the CD-ROM of the Windows 2000 Server. Selecting a driver for the IDE RAID controller To select the driver, follow these steps. 1 Press the key after the Windows 2000 Server Setup window has turned entirely to blue. 2 When a message appears on the screen, asking whether you want to add a device driver for mass storage device, press the key.
Installing Software Windows® 2000 Server 175 8 When the following message appears, select “Adaptec AIC7892 Ultra160 SCSI ”. Adaptec ACI-7892 Ultra160 SCSI Selecting a driver for the RAID controller E/F (MR493/MR475) To select the driver, follow these steps. 1 Press the key after the Windows 2000 Server Setup window has turned entirely to blue. 2 When a message appears on the screen, asking whether you want to add a device driver for mass storage device, press the key.
176 Installing Software Windows® 2000 Server Installing the display driver When installation of the Windows 2000 Server is complete, it is required to change the driver that is automatically detected by the Windows 2000 Server Installer to the display driver contained on the CD-ROM of the Toshiba Server Setup Tool.
Installing Software Windows® 2000 Server 177 3 Click “Next” in the “Update Device Driver Wizard”. 4 Select “Search for a suitable driver for my device” , click Next 5 Set Server Setup Tool CD into CD-ROM drive, check at “Specify a location”, click “Next”. 6 Type following driver pass to “Copy manufacture's files from:”, then click “Next” :\Public\Lan\Intel\Pro100\W2k 7 Click “Next”. 8 Click “Finish” in the “Finish screen”. 9 Update other Ethernet Controller in same method. 10 Restart computer.
178 Installing Software NetWare 6 Install the Service and Software (Power Console Plus) of the RAID Controller (when the RAID Controller is additionally connected) or MegaRAID Configuration Console (when IDE RAID is used). 7 Install the Backplane Driver (when IDE RAID is used). Use the floppy disk supplied with the RAID Controller for installation. See “MegaRAID Software Guide” for details of installation.
Installing Software NetWare 179 Intel LAN NetWare Driver AMI IDE RAID NetWare Driver Setup of the MS-DOS environment Installation of NetWare can be done in the three ways : (1) Install the MS-DOS by use of the Toshiba Server Setup Tool so that the installing environment for the NetWare is automatically set up. After the MS-DOS is installed by the Toshiba Server Setup Tool, the environment to read the CD-ROM of NetWare is automatically set up.
180 Installing Software NetWare (2) The CD-ROM drive is recognized by MS-DOS. To make the MS-DOS recognize the CD-ROM drive, set up the MS-DOS environment as mentioned in the preceding step (1) and set the floppy disk labeled “DOS Disk” (created by the Toshiba Server Setup Tool) on the floppy disk drive. Then, operate as follows: 1 Create the directory XXX in the drive C for installing the CDROM driver. The “XXX” is an arbitrary directory name.
Installing Software NetWare 181 1 Move the cursor to “Storage adapters” on the menu shown above with the arrow keys, and press the key. The following drivers were detected for this server. Add, change,or delete device drivers as needed. Device types Driver names Platform Support Module: HotPlug Support Module: Storage adapters MPS14 (optional) ADPT160M, IDEATA options _Continue _Modify 2 As the following menu appears, delete “ADPT160M” with the key. Add, edit, or delete storage drivers.
182 Installing Software NetWare 6 Input Slot Number “10008” to MEGAIDE property. Proceed with installation by following the instructions that appear on the screen: Selecting the SCSI Riser card driver The installer detects the SCSI controller, and the following menu appears. Select “Modify,” and replace the driver according to the following procedure: The following drivers were detected for this server. Add, change,or delete device drivers as needed.
Installing Software NetWare 183 2 As the following menu appears, delete “ADPT160M” with the key. Add, edit, or delete storage drivers. Each controller/adapter requires a driver. Driver name Device name Stat ||Adpt160m.HAM|| Adaptec Ultra160 ASPI & SCSI Module|| ||IDETA.HAM || Generic ATA/IDE/ATAPI.Adapter || Additional Driver Options _Return to driver summary _Modify 3 Insert the Adaptec Ultra160 NetWare Driver created with the Toshiba Server Setup Tool in the floppy disk drive.
184 Installing Software NetWare Select “Modify,” and replace the driver according to the following procedure: The following drivers were detected for this server. Add, change,or delete device drivers as needed. Device types Driver names Platform Support Module: HotPlug Support Module: Storage adapters MPS14 (optional) ADPT160M, IDEATA options _Continue _Modify 1 Move the cursor to “Storage adapters” on the menu shown above with the arrow keys, and press the key.
Installing Software NetWare 185 5 Press the key to designate the directory of the floppy disk as follows. A: \NetWare\NW5 As the driver is detected, it is added to the “List of drivers currently selected,” as shown below. || MEGA4_XX.HAM || AMI MegaRAID Enterprise 160 1700/ Express500 Adap || Proceed with installation operation following the instructions that appear on the screen.
186 Installing Software NetWare 4 Select “Add an unlisted driver ” by pressing the key. 5 Press the key to retrieve drivers contained in the floppy disk. 6 When the drivers are detected, they are added to the “List of network drivers currently selected.” || CE100B.LAN || Intel PRO/100 S ServerAdapter|| || CE100B.LAN || Intel PRO/100 S ServerAdapter|| Proceed with installation by following the instructions that appear on the screen. For installing the NetWare 4.
Installing Software NetWare 187 Selecting the driver to install the NetWare 4.2 When the NetWare installer detects the SCSI disk adapter and the network adapter, it displays a window as shown below. Choose the Server Drivers-Summary This is a summary of automatically or manually selected devices. Select additional drivers as needed.
188 Installing Software NetWare A: \NetWare 5 Press the key to retrieve drivers contained in the floppy disk. 6 When the driver list appears, select the following driver. || MEGAIDE.HAM || Netware NWPA HyperDisk HAM Driver || Proceed with installing operation, following the instructions that appear on the screen.
Installing Software NetWare 189 1 Select “Select an additional driver.” 2 Set the floppy disk labeled “MegaRAID Drivers & Utilities for SeriesXXX NetWare/MS-DOS” (supplied with the RAID Controller) in the floppy disk drive. 3 Select “Install an unlisted driver ” by pressing the key. 4 Press the key and specify the following directory under the floppy disk drive. A: \NetWare\NW5 5 Press the key to retrieve drivers contained in the floppy disk.
190 Installing Software NetWare 4 When the driver list appears, select the following driver. || CE100B.LAN || Intel(R) PRO PCI Adapter(CHSM spec 1.11)|| || IANS.LAN || Intel(R) Advanced Network Services Driver || 5 Input slot number “10005” to CE100B Parameters. Proceed with installing operation, following the instructions that appear on the screen.
Installing Software HarnessEye/web 191 HarnessEye/web HarnessEye/web is a total server management application software. HarnessEye/web functions on Windows NT/2000 Server only. Installing and operation See “HarnessEye/web User's Guide” (on the Documentation CDROM) .
192 Installing Software AFT, ALB and IPSec functions AFT, ALB and IPSec functions The Network Adapter that is mounted in the server as the standard device has the adapter fault tolerance (AFT) function, adaptive load balance (ALB) function and IP Security(IPSec) function. Those functions can be utilized if an optional extension network adapter is installed. What are the AFT and ALB functions? AFT (Adapter Fault Tolerance) The AFT function is realized by the primary adapter and secondary adapter.
Installing Software AFT, ALB and IPSec functions 193 1 Start up “Intel(R)PROSet II” from “Start” - “Settings” - “Control panel”. 2 Select one LAN adapter to configure AFT/ALB on from the “Intel(R)PROSet II” adapter list, click the right mouse button, and select “Create New Team” under “Add Team”. 3 The Teaming Wizard screen is displayed. Select either “Adapter Fault Tolerance” or “Adaptive Load Balancing”, and click “Next”.
194 Installing Software AFT, ALB and IPSec functions c The LAN card and the device driver for the LAN card are installed. c PROSETII is installed. 2 Install AFT/ALB. 3 Open the control panel by “Start” - “Settings” - “Control panel”, and start up “Intel(R)PROSet II”. 4 Select one LAN adapter to use IPSEC functions on from the “Intel(R)PROSet II” adapter list, click the right mouse button, and check the “enable IPSEC” checkbox.
Installing Software AFT, ALB and IPSec functions 195 13 The Behavior screen is displayed. Set as follows: c Mark the “Secure initiator” checkbox at “Behavior”. c Enter the temporary shared key at “Pre Shared Key”. NOTE: Any character string (alphabetics, numbers, symbols) of six characters or more can be used as the temporary shared key. This key is an encryption key that is used temporarily when initially determining the encryption key for performing communications in the IPSEC mode.
196 Installing Software AFT, ALB and IPSec functions Creating the PROSetII icon The PROSetII icon is used for setting AFT/ALB. 1 The Toshiba Server Setup Tool CD-ROM (supplied) in the CD-ROM drive. Note: A the screen that is displayed after the CD-ROM is inserted, click “Exit” to close the screen. 2 Browse the CD-ROM drive on Explorer, and double-click setup.exe in the following directory: : \Public\Utils\Intel\Aft-alb\Setup\setup.
Installing Software AFT, ALB and IPSec functions 197 2 Select a LAN adapter to which AFT/ALB is to be configured in the list of adapters in “Intel(R)PROSetII”, and select “Right click” → “Add Team” → “Create New Team”. 3 The “Teaming Wizard” screen is displayed. Select either “Adapter Fault Tolerance” or “Adaptive Load Balancing”, and select “Next”. 4 Mark the LAN adapter to add to the configuration, and select “Next”. 5 Select “Done” at “Team Wizard”.
198 Installing Software AFT, ALB and IPSec functions finger from the mouse button. When you do this, the “Welcome to the IP Security Policy Wizard” screen appears. (3) In the “Welcome to the IP Security Policy Wizard” screen, click “Next”. You will be prompted to enter the name of the policy to create. Decide upon and enter an appropriate name, and click “Next”.
Installing Software AFT, ALB and IPSec functions 199 checkbox, and set the same temporary shared key as in (4). When you have set the temporary shared key, select “Next”. (10)When the “IP Filter List” screen is displayed, mark the “All IP Traffic” checkbox, and select “Next”. (11)When the “Filter Action” screen is displayed, mark the “Request Security (Optional)” checkbox, and select “Next”. The screen changes to the “Completing the Rule Wizard” screen.
200 Installing Software AFT, ALB and IPSec functions (18)When the “IP Filter List” screen is displayed, make sure that the “All ICMP Traffic” checkbox is marked, and select “Next”. (19)When the “Filter Action” screen is displayed, mark the “Permit” checkbox, and select “Next”. The screen changes to the “Completing the New Rule Wizard” screen. Make sure that the “Edit properties” checkbox is marked, and select “Done”.
Installing Software AFT, ALB and IPSec functions 201 When using NetWare: Loading of AFT or ALB is supported on NetWare 4.2 or later version. 1 Append by the LOAD statement to the server's AUTOEXEC.NCF file so that AFT or ALB are automatically loaded each time that the server is started up. Example 1: To load AFT LOAD :\\NBI.NLM LOAD :\\MSM.NLM LOAD :\\ETHERTSM.NLM LOAD :\\CE100B SLOT=1 FRAME=ETHERNET_802.
202 Installing Software Auto-shutdown function Auto-shutdown function The auto-shutdown enables automatic execution of the sequence from shutting down the OS by the power switch through to turning OFF the power. The auto-shutdown function runs only on Windows NT/2000. Setting the auto-shutdown function Manually install the auto-shutdown function by installing HarnessEye/web after installation of Windows NT/2000 is completed.
Chapter 6 Troubleshooting ........................................................................ 204 Trouble with Application Software ........................................ 211 Remedy When Windows NT/2000 is Usable ...................... 212 Remedy When Windows NT/2000 is Unusable ..................
Troubleshooting Troubleshooting If you sense some abnormality on the server, carry out the following checks according to the problem that is occurring. NOTE: Before you check the server cables or expansion cards, switch off the server and peripheral devices. If checks are performed on the cables or expansion cards with the power on, irreparable damage may be caused to the server and peripheral devices.
Troubleshooting Troubleshooting 205 1 Immediately switch the server off, and disconnect the plug from the AC outlet. 2 Does the installation site satisfy the environmental considerations (e.g. ambient temperature and humidity)? See “Environmental considerations” on page 5. 3 Are there any foreign objects blocking ventilation holes? Nothing happens if you press the power switch.
206 Troubleshooting Troubleshooting See the operating manual of the display unit. 6 When running Windows NT/2000, boot up in the VGA mode, and make sure that the settings (resolution, synchronizing frequency) are as supported by the display unit. Characters are distorted or not displayed properly Probable causes are faulty connection of the display signal cable or power cable, or a problem with the brightness or contrast settings. Carry out the following procedure to check the cause of the trouble.
Troubleshooting Troubleshooting 207 The power indicator on this server lights with the power cord connected to the AC outlet or while the server is in the power save mode in the case of Windows 2000. See “System status indicators” on page 14/page 114/page 128. See “HDD/LAN status indicators” on page 19/page 115. The disk and STS indicators light and flash amber A probable cause is that a hard disk drive connected to the RAID controller is malfunctioning.
208 Troubleshooting Troubleshooting An error is displayed during POST operation, or POST stops midway Probable causes are the motherboard, CPU, memory or keyboard malfunction, or that the BIOS setup is incompatible. Carry out the following procedure to check the cause of the trouble. If Windows NT/2000 can be used, see “Remedy When Windows NT/2000 is Usable” on page 212. If Windows NT/2000 cannot be used, see “Remedy When Windows NT/2000 is Unusable” on page 213.
Troubleshooting Troubleshooting 209 See the Software Guide of the RAID controller. Cannot install the OS A probable cause is that the hard disk drive is not recognized. Carry out the following procedure to check the cause of the trouble. If this does not remedy the problem, see “Remedy When Windows NT/2000 is Unusable” on page 213. 1 Are the SCSI controller and RAID controller properly connected? See “Expansion cards” on page 103. See the Software Guide of the RAID controller.
210 Troubleshooting Troubleshooting See the operating manual of the expansion card. See the operating manual of the peripheral devices. 1 Are all cables firmly and properly connected? Check only the cables within the scope described in this manual, and instruction manuals for expansion cards and peripheral devices.
Troubleshooting Trouble with Application Software 211 See the operating manual of Harness Eye / web See the operating manual of respective device. The power button does not function after abortion If, after abortion of the system, it cannot be started by pressing the power button, unplug the power cable once and then supply the power to the server again. The internal clock does not keep precise time Generally, a slight error occurs in clock precision.
212 Troubleshooting Remedy When Windows NT/2000 is Usable Was the entire necessary procedure executed, and were all necessary files installed? 5 Is the correct device driver installed? 6 Is the software set up properly? 7 Is the software used correctly? If the trouble cannot be solved, contact the customer service section of the software manufacturer.
Troubleshooting Remedy When Windows NT/2000 is Unusable 213 functioning, contact your Toshiba Technical Support with the system still running. NOTE: If one of the devices has malfunctioned on a system equipped with a redundant Hard Disk Drive (HDD), the malfunctioning device can be hot-swapped.
214 Troubleshooting Remedy When Windows NT/2000 is Unusable
Appendix A System Unit ............................................................................... 216 External Hard Drive Unit Z1 ................................................... 218 External Device Bay Unit Z1 ..................................................
Specifications System Unit Model number of the unit CPU Main processor Max. processors Cache Second cache Main memory with ECC MAGNIA Z300 Pentium III 866MHz, 1 GHz 2 32KB/CPU 256KB/CPU 3GB (1GB x 3) 128MB/256MB/512MB/1GB 152GB (76GB x 2) Maximum capacity Unit of expansion Auxiliary IDE Maximum capacity storage HD (built-in) units D Additional HDD 20GB, 40GB,76GB Standard disk chassis 3.5” x 2 (hot-swap specs.) FDD Option(USB) 3.5” (720KB/1.
217 RAID controller Max. disk cache capacity SCSI controller Power Standard supplies CD-ROM Keyboard Mouse LAN interface Display I/O ports Micro Tower Type Rack Type (24 times as fast) x 1 Std (Micro Tower models only) Std (Micro Tower models only) 100Base-TX/10Base-T Ethernet x2 Onboard Standard Wake On LAN, AFT, and ALB applicable. 8MB 1 channel (Mini Din 8-pin) 2 channels 1 channel, PS/2 compatible 1 channel, PS/2 compatible 1 channel 3.5” x 2 1 Can only be added at the user site as an optional item.
218 External Hard Drive Unit Z1 SCSI HDD Maximum capacity Additional HDD Expantion disk chassis Remote Power Control Remote Sensing Interface Power Standard supplies Uninterruptible power supply (UPS) Power and frequency Power consumption Environmental Micro Tower Type conditions Rack Type Dimensions (mm) Micro Tower Type Rack Type Maximum server Micro Tower Type weight Rack Type 292GB (73GB x 4) 18GB, 36GB, 73GB 3.5” x 4 (hot-swap specs.
219 External Device Bay Unit Z1 Support Device Remote Power Control Remote Sensing Interface Power Standard supplies Uninterruptible power supply (UPS) Power and frequency Power consumption Environmental Micro Tower Type conditions Rack Type Dimensions (mm) Micro Tower Type Rack Type Maximum server Micro Tower Type weight Rack Type DAT DDS4 DAT DDS4 A/L AIT2 AIT2 A/L Standard Fan, Temperature, Voltage Ultra Wide SCSI 1 Can only be added at the user site as an optional item. 100 - 240 VAC, 50/60 Hz Max.
220
Appendix B RGB interface ........................................................................... 222 Serial interface ........................................................................... 224 Keyboard/mouse interface ....................................................... 225 LAN-1/2 interface .................................................................... 226 USB-1/2 interface ..................................................................... 226 Expansion slots (64bit/66MHz PCI slot) .
Interfaces The output voltages from the I/O connectors on the back of chassis do not exceed 12V. RGB interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. .
223 Pin number Signal name Meaning I/O 8 GND Signal ground 9 Unused Not used 10 GND Signal Ground 11 Unused Not used 12 Unused Not used 13 _CHSYNC Horizontal Sync Signal (TTL) O 14 _CVSYNC Vertical Sync Signal (TTL) O 15 Unused Not used 5 1 15 11 10 6 RGB interface synchronizing signals Resolution 640 x 480 Colors 256, 64K, 16M 256, 64K, 16M 256, 64K Scanning Non-interlaced Horizontal sync (kHz) Vertical sync(Hz) 800 x 600 1024 x 768 Non-interlaced Non-interlace
224 Serial interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server. .
225 Pin number Signal name Meaning I/O 7 RTS Request To Send O 8 CTS Clear To Send I 9 CI Call Indicator I 1 5 6 9 Keyboard/mouse interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server.
226 LAN-1/2 interface NOTE: In the table below, “I/O” denotes the input/output when seen from the server.
227 Expansion slots (64bit/66MHz PCI slot) NOTE: In the table below, “I/O” denotes the input/output when seen from the server. Expansion slots (for expansion PCI cards) 3.3V-system environment Pin number Side B I/O Side A TRST_L I/O 1 -12V 2 TCK 3 GND 4 TDO 5 +5V +3.
228 Pin number 3.3V-system environment Side B I/O Side A I/O 23 AD27 I/O AD26 I/O 24 AD25 I/O GND 25 +3.3V 26 C/BE3_L 27 AD23 28 GND 29 AD21 30 AD19 31 +3.3V 32 AD17 33 C/BE3_L 34 GND 35 IRDY_L 36 +3.3V 37 DEVSEL_L 38 GND 39 LOCK_L I/O +3.3V 40 PERR_L I/O SDONE I/O 41 +3.3V SBO_L I/O 42 SERR_L 43 +3.3V 44 CBEI_L 45 AD14 46 GND 47 AD12 48 AD10 49 GND AD09 50 GND GND AD24 I/O I/O IDSEL O I/O +3.
229 3.3V-system environment Pin number Side B I/O Side A I/O 51 GND GND 52 AD08 I/O C/BE0_L 53 AD07 I/O +3.3V 54 +3.3V 55 AD05 56 AD03 57 GND 58 AD01 59 +3.3V 60 ACK64_L 61 +5V +5V 62 +5V +5V 63 Reserved GND 64 GND C/BE7_L I/O 65 C/BE6_L I/O C/BE5_L I/O 66 C/BE4_L I/O +3.3V 67 GND 68 AD63 69 AD61 70 +3.
230 Pin number 3.3V-system environment Side B I/O Side A 79 +3.3V 80 AD47 81 AD45 82 GND 83 AD43 84 AD41 85 GND 86 AD39 87 AD37 88 +3.3V 89 AD35 90 AD33 91 GND AD32 92 Reserved Reserved 93 Reserved GND 94 GND Reserved I/O AD48 I/O I/O AD46 I/O I/O GND AD44 I/O I/O AD42 I/O I/O +3.
Appendix C Hardware setup information .................................................... 232 Recovery Boot ..........................................................................
Switch Setting Hardware setup information Perform the following operations if the hardware setup information is to be forcibly returned to the standard settings (CMOS Clear): 1 Disconnect the AC power cable. 2 Remove the server panels, power supply unit and board for wireless card. 3 Set the jumper switch PJ47 on the motherboard to 1-2 short. PJ47: 1-2 short ... Clears the hardware data settings. 3-4 short...
233 7 Remove the sever panels, power supply unit and board for wireless card, and return the jumper switch to 3-4 short. 8 Install the board for wireless card, the power supply unit and server panels. 9 Connect the AC power cable again and restart your server. 10 Start the BIOS Setup Utility, set System Time and System Date and select “Load Setup Default” from the Exit menu to execute it.
234 Following message is displayed on the front panel display and the power is automatically turned off if BIOS recovery was succeeded. BIOS Recovery Boot succeeded. 6 Following message is displayed if BIOS recovery was failed. Return to step 5 and repeat recovery process. BIOS Recovery Boot failed. 7 Disconnect the AC power cable.
235 PJ47:CMOS Clear PJ723: Recovery Boot Default Jumper Switch Settings
236
Appendix D
Trouble Information The following information is displayed on the front panel display when a trouble occurs. Display Meaning of Message ALARM (01) Baseboard +1.5V low. Low voltage error of main unit +1.5V power supply. ALARM (02) Baseboard +1.5V high. High voltage error of main unit +1.5V power supply. ALARM (03) Baseboard +2.5V low. Low voltage error of main unit +2.5V power supply. ALARM (04) Baseboard +2.5V high. High voltage error of main unit +2.5V power supply. ALARM (05) Baseboard +3.
239 Display Meaning of Message ALARM (11) Baseboard +12.0V low. Low voltage error of main unit +12.0V power supply. ALARM (12) Baseboard +12.0V high. High voltage error of main unit +12.0V power supply. ALARM (13) CPU1 core voltage low. The CPU1 core low power voltage error has occurred. ALARM (14) CPU1 core voltage high. The CPU1 core high power voltage error has occurred. ALARM (15) CPU2 core voltage low. The CPU2 core low power voltage error has occurred. ALARM (16) CPU2 core voltage high.
240 Display Meaning of Message ALARM (31) Ex. Disk1 +5.0V low. Low voltage error of External Hard Drive Unit 1+5.0V power supply. ALARM (32) Ex. Disk1 +5.0V high. High voltage error of External Hard Drive Unit 1+5.0V power supply. ALARM (33) Ex. Disk1 +12.0V low. Low voltage error of External Hard Drive Unit 1+12.0V power supply. ALARM (34) Ex. Disk1 +12.0V high. High voltage error of External Hard Drive Unit 1+12.0V power supply. ALARM (35) Ex. Disk1 FAN1 RPM slow.
241 Display Meaning of Message ALARM (51) Ex. Disk2 temp1 high. The External Hard Drive Unit 2 high temperature error 1 has occurred. ALARM (52) Ex. Disk2 AC lost. Power interruption reset was detected on External Hard Drive Unit 2. ALARM (53) Ex. Disk2 power sag. Momentary power interruption was detected on External Hard Drive Unit 2. ALARM (54) Ex. Disk2 power supply fault. External Hard Drive Unit 2 power supply error. ALARM (55) Ex. Disk2 chassis intrusion.
242 Display Meaning of Message ALARM (71) Ex. Device Bay2 +5.0V low. Low voltage error of External Device Bay Unit 2+5.0V power supply. ALARM (72) Ex. Device Bay2 +5.0V high. High voltage error of External Device Bay Unit 2+5.0V power supply. ALARM (73) Ex. Device Bay2 +12.0V low. Low voltage error of External Device Bay Unit 2+12.0V power supply. ALARM (74) Ex. Device Bay2 +12.0V high. High voltage error of External Device Bay Unit 2+12.0V power supply. ALARM (75) Ex. Device Bay2 FAN1 RPM slow.
Appendix E Unit logs ..................................................................................... 244 Basic system configuration ..................................................... 245 CPUs .......................................................................................... 245 Memories ................................................................................... 245 IDE Hard disk drives ................................................................ 246 SCSI units ................
Unit Logs Unit logs Unit logs are listed on following pages. Use these logs to record system component additions and information on removed optional items. The information that has thus been recorded may need to be used when executing various utilities. The unit logs consist of a log concerning the basic system configuration, and a log relating to added units (system components). Use the basic system configuration log to record the model numbers and serial numbers of the server and the motherboard.
245 The positions where the model numbers and serial numbers of the system components are inscribed vary from manufacturer to manufacturer. See the relevant product manuals. Basic system configuration Maker Serial number Date installed Model No./Type No.
246 IDE Hard disk drives Internal disk Capacity/ Revolutions Model number Date installed Slot1 Slot2 SCSI units Maker Model No./Type No. SCSI ID Date setting installed Internal Expansion cards Slot PCI-1 Maker Interrupt Model No./Type No.
247 Expansion units Cab No. Slot No. Maker Model No./Type No. SCSI ID setting Date installed Other optional items Slot Serial port (COM1) USB1 USB2 Maker Setting and others Model No./Type No.
248
