INSTRUCTION MANUAL CCD COLOR CAMERA IK-6550A Please read this manual thoroughly before use, and keep it handy for future reference. Record in space provided below the Model No. and the Serial No. as found on the label on the bottom of this unit. Model. No. IK-6550A Serial No. Retain this information for future reference. TABLE OF CONTENTS IMPORTANT SAFEGUARDS ................................................ 1. FEATURES & DESCRIPTION ...................................... 2. COMPONENTS ...................
IMPORTANT SAFEGUARDS 1. Read Instructions 13.Lightning All the safety and operating instructions should be read before the product is operated. For additional protection on this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the video product due to lightning and power-line surges.
• The CAUTION label, shown on the left, is attached on the camera. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1. FEATURES & DESCRIPTION 1. 24V AC/12V DC dual-voltage capable extends power choice. 2. Setting and adjustments are made by way of on-screen menu. (Menu Driven Set-Up) 3. Camera has the ability to automatically switch the display to color in daylight or black and white at night. 4. Camera synchronization mode is selectable between internal and line-lock. 5. The shutter speed is automatically adjusted according to the subject brightness. 6.
-5- Setting switch: D/N MODE / D/N LEVEL / SHUTTER / GAIN / SYNC / BLC / SHARPNESS / WB / DNR / CHROMA / PRIVACY ZONE / CAMERA ID / ID POS Front View Lens: Mount a CS-mount lens Focus Lock Screw Focus ring: Rotate the ring to adjust back focus. Auto -IRIS Terminal If using an auto iris lens, connect it to this terminal.
4. CAMERA INSTALLATION Wall 9.5 mm 80 6 4 Installation Example 1/4"-20UNC 112 15 The installation guide is for reference only. Mounting backet is not included.
5. CONNECTIONS AND OPERATIONS Notes on connecting • Power plugs of connected equipment must be disconnected before installations. • A 75-ohm coaxial cable with connector (3C-2V or 5C-2V) is required for standard connection. • For details of wiring and operation of equipment to be connected, refer to their operation manuals. • Lens, power supply with cable, connectors and coaxial cable are not supplied with the camera. 5-1.
5-2. Line-Lock Control • Matching the vertical synchronization with the power frequency is called the Line-Lock. • This function is activated when the SYNC menu is selected to LL. • When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching.
6. LENS Back-Focus Adjusment Back-Focus is adjusted at the factory to accommodate most standard lenses. However, at times, slight adjustment to the IK-6550A backFocus Lock Screw focus is necessary. Loosen the Focus Lock Screw. Achieve a clear image by rotating the focus ring. Afterwards, tighten the Focus Lock Screw. Focus ring This camera supports two types of auto-iris lens: Videotype and DC (direct drive) types. Connect the auto-iris connector plug to the IRIS terminal on the side of the camera.
7. LINE-LOCK PHASE If two or more cameras within a system have different AC line phases are switched by the video switcher, the picture on the monitor TV will fluctuate vertically. Connect 24V AC input lines of all cameras so that they all share the same phase. If you still have vertical fluctuation, adjust the V.PHASE controller. V.
8. MENU-DRIVEN SET-UP The setting menus of hierarchy are shown below and with on-screen character displays.
8-1.
8.2 Setting mode call and basics Press the SELECT switch down about 2 seconds then menu will appear on the display. Use the buttons to select . EXIT CANCEL DEFAULT 8-2-1. D/N MODE (DAY/NIGHT MODE) Selections: AUTO (default): The camera will sense the brightness level and switches to color mode or monochrome mode. COLOR: Color mode B/W: Monochrome mode Process: 1.
8-2-2. D/N LEVEL (DAY/NIGHT LEVEL) Selections: LOW (default): The chroma cut level is set less than 20 to 30 IRE. MID: The chroma cut level is set less than 30 to 40 IRE. HIGH: The chroma cut level is set less than 40 to 50 IRE. Process: 1. Position the cursor ( ) next to CAMERA SETUP and press the SELECT switch to access the camera menu. 2. Position the cursor ( ) next to D/N LEVEL and press the SELECT switch to access menu. 3. Use the buttons to select LOW, MID or HIGH. 4.
8-2-4. GAIN (AGC) Selections: OFF: AGC does not operate. STD (default): Standard position, max gain = 24dB HIGH: High-Sensitivity position, max gain = 30dB Process: 1. Position the cursor ( ) next to CAMERA SETUP and press the SELECT switch to access the camera menu. 2. Position the cursor ( ) next to GAIN and press the SELECT switch to access menu. 3. Use the buttons to select OFF, STD or HIGH. 4. Press the SELECT switch to accept the selection.
8-2-6. BLC (BACK LIGHT COMPENSATION) Selections: When using the automatic electronic iris with an auto iris lens, the exposure adjustment is automatically performed so that the best picture is obtained at the next monitor zone. The four different BLC zones are displayed below: Process: 1. Position the cursor ( ) next to CAMERA SETUP and press the SELECT switch to access the camera menu. 2. Position the cursor ( ) next to BLC and press the SELECT switch to access menu. 3.
8-2-7. SHARPNESS Selections: Adjust the outline correction. LOW: to make the outline softer. MID (default): to make the outline standard. HIGH: to make the outline clearer Process: 1. Position the cursor ( ) next to CAMERA SETUP and press the SELECT switch to access the camera menu. 2. Position the cursor ( ) next to SHARPNESS and press the SELECT switch to access menu. 3. Use the buttons to select LOW, MID or HIGH. 4. Press the SELECT switch to accept the selection.
8-2-9.
(3) BACK Position the cursor ( ) next to BACK and press the SELECT switch to exit OPTION menu. DNR CHROMA BACK MID 3 D/N MODE D/N LEVEL SHUTTER GAIN SYNC BLC SHARPNESS WB
8-2-11. Press the SELECT switch down about 2 seconds then menu will appear on the display. Use the buttons to select . Process: 1. Position the cursor ( ) next to PRIVACY ZONE and press the SELECT switch to access the menu. 2. Position the cursor ( ) next to ZONE 1 ~ 8 and press the SELECT switch to access menu. 3. Use the buttons to select ON and press the SELECT switch. The mark will appear on the display.
4. Use the buttons to set ZONE POSI (H) and press the SELECT switch. ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 BACK OFF OFF OFF OFF OFF OFF OFF OFF ZONE POSI(H) 5. Use the buttons to set ZONE POSI (V) and press the SELECT switch.
6. Use the buttons to set ZONE SIZE (H) and press the SELECT switch. ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 BACK OFF OFF OFF OFF OFF OFF OFF OFF ZONE SIZE(H) 7. Use the buttons to set ZONE SIZE (V) and press the SELECT switch. ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 BACK OFF OFF OFF OFF OFF OFF OFF OFF ZONE SIZE(V) 8-2-12. BACK Position the cursor ( ) next to BACK and press the SELECT switch to exit PRIVACY ZONE menu.
Press the SELECT switch down about 2 seconds then menu will appear on the display. Use the buttons to select . EXIT CANCEL DEFAULT 8-2-13. CAMERA ID Position the cursor ( ) next to CAMERA ID and press the SELECT switch to access the CAMERA ID menu. Position the cursor ( ) next to CAMERA ID and press the SELECT switch. Use the buttons, to name each camera up to 16 characters. Press the SELECT switch to accept the selection.
8-2-14. ID POS (ID POSITION) Selections: OFF (default): Disappear the CAMERA ID. TOP: Show the ID position top-left of screen. BOTTOM: Show the ID position bottom-left of screen. CAMERA ID ID POS BACK OFF Process: 1. Position the cursor ( ) next to CAMERA ID and press the SELECT switch to access the camera menu. 2. Position the cursor ( ) next to ID POS and press the SELECT switch to access menu. 3. Use the buttons to select OFF, TOP or BOTTOM. 4. Press the SELECT switch to accept the selection. 8-2-15.
8-2-16. EXIT (save the changed settings) Position the cursor ( ) next to EXIT and press the SELECT switch to exit menu. EXIT CANCEL DEFAULT 8-2-17. CANCEL (discard the changed settings) Position the cursor ( ) next to CANCEL and press the SELECT switch twice to load cancel settings. EXIT CANCEL DEFAULT 8-2-18.
9.
10. NOTES ON USE AND INSTALLATION • Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. • Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction. • Treat the camera with care Do not drop the camera or subject it to strong shock of vibration. • Never touch internal parts Do not touch the internal parts of the camera other than the parts specified.
12. SPECIFICATIONS Power AC 24V ~ ±10% 60 Hz/DC 12V Power consumption 4.5W (max) with Al lens Image sensor 1/3 inch CCD image area sensor Image pickup area 4.96 mm (0.195 inch) horizontal × 6.0 mm (0.236 inch) vertical (1/3 inch type) Effective picture element 768 horizontal × 494 vertical Scanning system 2:1 interlace NTSC Standard TV system Scanning frequency 15.
13.
MEMO
MEMO
LIMITED WARRANTY CCD SECURITY CAMERA IK-6550A The Imaging System Division ("ISD") of Toshiba America Information Systems, Inc. makes the following limited warranties with regard to this CCD Camera Model IK-6550A ("Product"). These limited warranties extend to the Original End-User ("You[r]"). Three (3) Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of three (3) years from the date of purchase by the Original End-User.