TOSHIBA Storage Diagnostic Tool Version 1.11.
Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA CORPORATION AND ITS AFFILIATES (“TOSHIBA”) PROVIDE NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING.
Contents Notice .................................................................................................................................................................................... 2 DISCLAIMER ........................................................................................................................................................................ 2 About Trademarks .................................................................................................................
Revision History of Storage Diagnostic Tool Version 01 Revision Date December 2016 Description Initial version pg.
Safety Precautions This section lists important precautions which users of our product(s) (and anyone else) should observe in order to avoid injury to human body and damage to property and to ensure safe and correct use of our products. Please be sure that you understand the meanings of the labels and graphic symbols described below before you move on to the detailed descriptions of the precautions, and comply with the precautions stated.
General Use Do not remove the drive from your system while the system is powered on. It may cause damage to the drive. Prohibited Do not change any configuration files of this application. To do so could harm your system. Prohibited Instructions If your system or the TOSHIBA Storage Diagnostic Tool is terminated abnormally while TOSHIBA Storage Diagnostic Tool is running, your system or the drive may be damaged or data may be lost.
1. Introduction This manual describes the procedure for using TOSHIBA Storage Diagnostic Tool (hereinafter “Diagnostic Tool”). Please read carefully the DISCLAIMER and Safety Precautions section before using the Diagnostic Tool application. The Diagnostic Tool is software for the diagnostic scan of TOSHIBA External HDD, Internal HDD and Internal SSD (hereafter “TOSHIBA Storage”).
2. System Requirements Diagnostic Tool requires the following: a) Supported Toshiba Storage External Drive USB3.
b) Supported Hardware Computers that satisfy the requirements of a supported operating system. Interface: USB 3.0 / USB 2.0 / Serial ATA c) Disk Space 4.92 MB of available disk space d) Supported Operating Systems Windows 10 Version 1507 / 1511 (32 bit / 64 bit) Windows 8.
3. Diagnostic Tool Usage 3.1. Preparing the Diagnostics Tool Save the “ToshibaStorageDiagnosticTool.exe” to a folder on your computer. Requires username and password of administrator account in order to be saved by a general user. Note 3.2. Starting the Diagnostic Tool You can start the Diagnostic Tool application by the following ways: Requires username and password of administrator account in order to be started by a general user. Note 1) Double-click the “ToshibaStorageDiagnosticTool.exe”.
4. Summary 1 5 4 3 2 1) File(F) Refresh View Log Exit : Refresh of Drive. : Displays log file (diag_result_log.txt). : Closes Diagnostic Tool application. 2) Function(U) Start/Stop Diagnostic Scan Start/Stop Zero Filling : Goes to the Diagnostic Scan screen (See 6. Diagnostic Scan) . : Goes to the Zero Filling screen (See 7. Zero Filling). 3) Drive Information : Displays Drive Information (See 5. Drive Information).
5. Drive Information Displays the list of all available drives on your system. 2 3 4 5 6 7 1 TEST SAMPLE 1) 2) Type Model Number 3) 4) 5) 6) Serial Number Capacity Security Status Test Status 7) Time Stamp : Displays Interface of Drive. : Displays Model Name of the External Hard Drive (Model Number of Internal Hard Drive). Displays Model Number of Internal Hard Drive.
6. Diagnostic Scan The Diagnostic Scan can scan all or part of the TOSHIBA Storage for read errors. There are two kinds of the Diagnostic Scan: Quick Scan and Full Scan. The Quick Scan runs self-test routine on one part of the drive. Typically, it takes several minutes to complete a Quick Scan. The Full Scan runs self-test routine on the whole drive. Typically, it may take several hours or more to complete a Full Scan. The result of executing the Diagnostic Scan can be viewed in “Test Status”.
3) Select “Quick Scan” or “Full Scan” then click “Yes” to scan the selected drive. ･Quick Scan ･Full Scan : Check this option to run self-test routine on one part of the selected drive. : Check this option to run self-test routine on all of the selected drive. Full Scan will be displayed the estimated required time. TEST SAMPLE Full Scan time may exceed the estimated required time depending on the operating conditions. Information In “Test Status”, displays ratio of scanning task. TEST SAMPLE pg.
4) During execution of the scan, if you would like to stop the scan process, click “Start/Stop Diagnostics Scan”. TEST SAMPLE Click “Yes” to stop the scan process. 5) “PASS” or “Error detected.” is displayed when the scan is terminated normally. “ABORT” is displayed if you stop the scan process, and click “OK” to finish. pg.
7. Zero Filling Function The Zero Filling function overwrites the whole user data are with zero data pattern on the selected drive. This process takes longer, and the completion time depends on the capacity and the condition of the drive. Please make sure to back up your necessary data before starting the Zero Filling process. Zero Filling function does not work with the system drive. Zero Filling function isn't available on drive that the Diagnostic Tool stored.
3) If you accept the conditions, check “I understand” and click “Yes” 4) If you accept the conditions, check “I understand” and click “Yes”, and start Zero Filling function. In “Test Status”, displays ratio of Zero Filling task. TEST SAMPLE pg.
5) During execution of Zero Filling function, if you would like to stop Zero Filling function, click “Start/Stop Zero Filling”. TEST SAMPLE Click “Yes” to stop Zero Filling function. 6) “PASS” or “Error detected.” is displayed when the scan is terminated normally. “ABORT” is displayed if you stop the scan process, and click “OK” to finish. pg.
Need Help? Please visit TOSHIBA’s Support Web site. support.toshiba.com/ pg.
1-1, Shibaura 1-Chome, Minato-ku, Tokyo 105-8001, Japan Issued in December 2016 Copyright © 2016 TOSHIBA CORPORATION, All Rights Reserved. pg.
