E9TK4BD_EN.book Page 1 Wednesday, January 6, 2010 10:05 PM Introduction Basic Setup / TV View Operation DVR20KB Connections DVD / VIDEO CASSETTE RECORDER OWNER’S MANUAL Recording PAL Playback Editing Function Setup EN For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
E9TK4BD_EN.book Page 2 Wednesday, January 6, 2010 10:05 PM . Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
E9TK4BD_EN.book Page 3 Wednesday, January 6, 2010 10:05 PM Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. • Keep the unit away from electronic equipment such as an amplifier, TV, etc. to prevent warping,damage, fire and malfunction. • Do not place anything directly on top of the unit. • Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations.
10_Intro.fm Page 4 Friday, January 8, 2010 4:40 PM Notice for the Progressive Scan Outputs Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 480 or 576 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output.
E9TK4BD_EN.book Page 5 Wednesday, January 6, 2010 10:05 PM Remote control with 2 R6 (1.5 V) batteries RF cable Owner’s Manual Quick Setup Guide Helpline Sheet The following features are available with this unit.
E9TK4BD_EN.book Page 6 Wednesday, January 6, 2010 10:05 PM Table of Contents Introduction ...................................................... 2 Editing ............................................................. 55 Precautions ........................................................................ 2 Guide to a Title List .......................................................... 55 Features ............................................................................. 5 Editing Discs .........
E9TK4BD_EN.book Page 7 Wednesday, January 6, 2010 10:05 PM Introduction Guide to the Owner’s Manual Symbols Used in the Owner’s Manual Symbol Connections To show what recording mode or media type applies to each function, the following symbols appear at the beginning of each operating item.
E9TK4BD_EN.book Page 8 Wednesday, January 6, 2010 10:05 PM Discs for Recording / Playing Disc Type DVD-RW DVD-R DVD+RW DVD+R Logo Automatically formatted in video mode Format Can be formatted in VR or video mode Video Mode Icon Maximum Record Time VR DVD-RW DVD-RW 480 min (12 cm) 144 min (8 cm) Playable on most DVD players. Finalisation Compatibility necessary.
E9TK4BD_EN.book Page 9 Wednesday, January 6, 2010 10:05 PM Introduction Discs for Playing Disc Type DVD-VIDEO CD-DA Video CD CD-RW CD-R Logo Icon CD VCD CD CD Connections DVD-V Files for Playing MP3 JPEG DivX® Icon MP3 JPEG DivX CD-RW/-R USB device CD-RW/-R USB device CD-RW/-R DVD-RW/-R DVD+RW/+R USB device (not guaranteed) Media ® is a trademark of DVD Format/Logo Licensing Corporation.
E9TK4BD_EN.book Page 10 Wednesday, January 6, 2010 10:05 PM Functional Overview Front Panel 1*3 2 3*1 4 VCR VCR PROGRAM DUBBING 5 DVD DVD SELECT VCR DVD USB 21 19*2 17*2 15 20*2 18 16 14 13 12 10 11 8 9*1 DV IN 7 6 You can also turn on the unit by pressing these buttons. You can turn on the unit by pressing these buttons only when a videotape is in this unit. Press to turn on the unit, or to turn the unit into the standby mode.
E9TK4BD_EN.book Page 11 Wednesday, January 6, 2010 10:05 PM 19 20 21 3 5 6 25 26 7 27 8 28 9 29 10 30 31 13 32 33 34 14 35 36 37 38 Note • If you turn off this unit, [OPEN\CLOSE A] on the remote control is not available. Be sure to use [A OPEN\CLOSE] or [STOP\EJECT C \ A] on the unit. VCR Functions Button names described in the Owner’s Manual The instructions in this manual are described mainly with the operations using the remote control.
E9TK4BD_EN.book Page 12 Wednesday, January 6, 2010 10:05 PM Installing Batteries in the Remote Control Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment. 1 2 Switching DVD / VCR mode You must select which component you want to operate first. Press [DVD] or [VCR] on the remote control or the front panel.
E9TK4BD_EN.book Page 13 Wednesday, January 6, 2010 10:05 PM Guide to On-Screen Displays Introduction Press [DISPLAY] repeatedly while the display menu is displayed to display the following information.
Title name information DISPLAY Menu Title Name DVD My Title T 1/ 5 C (only when DVD+RW/+R, VR mode DVD-RW or unfinalised video mode DVD-RW/-R disc is in playback) File name information 8 1 -RW VR ORG 2 1 BBC1 3 1/ 5 0:01:00 / 1:23:45 &ILE .E9TK4BD_EN.book Page 14 Wednesday, January 6, 2010 10:05 PM Main Menu VCR While in the VCR mode, the on screen display of the VCR mode is displayed. Press [VCR] first. Press [DISPLAY] to display the on screen display. Press [SETUP] to display the main menu. Then use [K \ L] to select a menu and press [ENTER\OK] to display the sub menu. Press [RETURN/BACK] to return to previous screen. .
E9TK4BD_EN.book Page 15 Wednesday, January 6, 2010 10:05 PM To programme a timer recording. [E Page 33] DISC Playback Mode Audio CD / video CD DISC Playback Mode Title List 1 2 3 To call up the title list.
E9TK4BD_EN.book Page 16 Wednesday, January 6, 2010 10:05 PM Front Panel Display Guide 1 2 DTV DB VCR 3 DVD 4 1 DTV indicator : Appears when a disc is in this unit. : Appears when the channel is in digital mode. 2 : : 3 DB : Title / Track and Chapter number Appears during dubbing. DVD :Appears when this unit is in DVD output mode, or Title / track number Chapter number the timer-standby mode for DVD recording.
E9TK4BD_EN.book Page 17 Wednesday, January 6, 2010 10:05 PM Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, unplug your TV and this unit Antenna RF cable (not supplied) 1 To Aerial jack Audio IN Component video IN Y PB/CB Recording If your TV has component video input jacks, use a component video cable (to connect the COMPONENT VIDEO OUT jacks) and an audio cable (to connect the AUDIO OUT (L\R) jacks).
E9TK4BD_EN.book Page 18 Wednesday, January 6, 2010 10:05 PM Using an HDMI Compatible Port [HDMI CONNECTION] • HDMI outputs the video / audio signals without converting to analogue signals. • No audio connections is required. • Use the HDMI cable (commercially available) for connection. • Connect the HDMI output jack of this unit to the HDMI input jack of TV.
E9TK4BD_EN.book Page 19 Wednesday, January 6, 2010 10:05 PM Recording from a DVD player, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2) Digital Audio for Better Sound Quality Dolby Digital decoder, DTS decoder or MPEG decoder, etc. Digital audio input jack COAXIAL Connections This unit has three input terminals. Press [INPUT SELECT F] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1, AV2 or DV(AV3).
E9TK4BD_EN.book Page 20 Wednesday, January 6, 2010 10:05 PM Basic Setup / TV View Operation Initial Setting When you turn on this unit for the first time, you need to follow these steps. 1 2 3 Press [B ON\STANDBY]. Turn the TV on. Select the input to which the unit is connected. Select your desired tuning type according to your area using [K \ L], then press [ENTER\OK]. Also you can customize the memorised channel at “General Setting”. Refer to following pages for details.
E9TK4BD_EN.book Wednesday, January 6, 2010 10:05 PM Select “Auto Tuning (DVB & ANALOG)” using [K \ L], then press [ENTER\OK]. The unit will start storing channels available in your area. General Setting Auto Tuning (DVB & ANALOG) DVB Channel Setup ANALOG Channel Setup 4 ANALOG You can preset an analogue channel manually and individually. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Channel” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 22 Wednesday, January 6, 2010 10:05 PM The tuner scans and memorises all the active DVB channels (TV / Radio) in your area. Skip a Preset Channel ANALOG Channel Search S.No. TV Channel You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H]. 1 Follow steps 1 to 4 in “Manual Tuning (ANALOG)” on page 21. 2 3 Select “Position” using [K \ L], then press [1].
E9TK4BD_EN.book Page 23 Wednesday, January 6, 2010 10:05 PM DVB The following operations are available while viewing TV channels through this unit’s tuner. 1 Select a Channel ANALOG • “Quick Select” menu will appear. To switch DVB, analogue and external input (AV1/AV2/ DV(AV3)) mode. Press [INPUT SELECT F] repeatedly to select DVB, analogue or external input mode. The mode changes as follows: Analogue mode Quick Select Group: All S.No.
E9TK4BD_EN.book Page 24 Wednesday, January 6, 2010 10:05 PM Edit Channels Edit Group Lists DVB DVB With “Edit Channels” menu, you can sort all the memorised DVB channels into the group lists (“Quick Select”) or set the viewer limitation (“Adult Lock”), etc. 1 2 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. Select “Channel” using [K \ L], then press [ENTER\OK]. 3 Select “DVB Channel Setup” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 25 Wednesday, January 6, 2010 10:05 PM Channel Move DVB DVB You can set the unit to limit the access to the DVB channels. Follow steps 1 to 4 in “Edit Channels” on page 24. 2 Select the DVB channel you want to limit the access using [K \ L], then press [YELLOW]. Edit Channels S.No. Channel Name 5 Fav. Skip Lock Del. Five Follow steps 1 to 4 in “Edit Channels” on page 24. 2 Select the DVB channel you want to change the position using [K \ L], then press [ENTER\OK].
30_BasicSetup.fm Page 26 Wednesday, January 6, 2010 10:37 PM Signal Information Multi Audio DVB DVB You can check the detailed information of the current DVB channel. 1 2 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 22. Many DVB channels transmit Multi Audio information along with their DVB channels. You can select the desired audio mode and audio language. 1 Select “Signal Information” using [K \ L], then press [ENTER\OK]. While viewing a DVB programme, press [AUDIO D].
E9TK4BD_EN.book Page 27 Wednesday, January 6, 2010 10:05 PM • If the programme is changed, the subtitle language will be switched back to the default language you set in the “DVB Setting”. Refer to “ Language” on page 69. If the default subtitle language is not available on the new programme, no subtitle will be displayed. 1 2 DVB While viewing a DVB programme, press [AD].
E9TK4BD_EN.book Page 28 Wednesday, January 6, 2010 10:05 PM Recording Restrictions on Recording Information on DVD Recording Type of Discs This unit can record on DVD-RW/-R discs and DVD+RW/+R discs. DVD-R/+R discs allow you to record programmes only once, and the recorded contents can be erased although the space left on the disc does not change. DVD-RW/+RW discs allow you to record programmes repeatedly, and the recorded contents can be erased.
E9TK4BD_EN.book Page 29 Wednesday, January 6, 2010 10:05 PM Introduction Making Discs Playable in Other DVD Players (Finalise) After recording, you must finalise the disc to play it back in other players. (See page 42.) You cannot finalise discs in other DVD recorders. Disc Type DVD-R DVD-RW Video Mode VR Mode ✔ ✔ ✔ ✔ ✔ DVD+RW DVD+R ✔ ✔ After finalising Undo finalising (See page 42.) Additional recording or editing (See page 42.
E9TK4BD_EN.book Page 30 Wednesday, January 6, 2010 10:05 PM Make Recording Compatible Formatting a Disc Choosing the Recording Format of a Blank DVD-RW Disc Video VR DVD-RW DVD-RW When inserting a brand-new DVD-RW/+RW disc, the unit automatically starts to initialise the disc. DVD+RW disc will always be formatted in +VR mode, and DVD-RW disc will be formatted either video or VR mode according to the recording format mode setting of the unit.
E9TK4BD_EN.book Page 31 Wednesday, January 6, 2010 10:05 PM Video 5 VR e.g.) VR mode DVD-RW DVD-RW DVD-RW DVD-R DVD+RW DVD+R The unit inserts a chapter mark periodically (every 15 minutes by default) during recording. Using the Auto Chapter menu, you can set this function off or change the time period. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 32 Wednesday, January 6, 2010 10:05 PM Setting Bilingual Recording Audio Video DVD-RW DVD-R DVD+RW DVD+R You can select either “Main” or “Sub” audio to record a bilingual broadcast in video mode or +VR mode. This setting is only for recording analogue channel. 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 33 Wednesday, January 6, 2010 10:05 PM 9 Introduction • When the unit reaches the specified time, it will be turned off automatically. • To change the recording length during One-touch Timer Recording, press [REC I] repeatedly until the desired length appears. • To cancel One-touch Timer Recording within the specified time, press [STOP C]. Timer Recording DVB ANALOG Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R Press [STOP C] to stop the recording.
E9TK4BD_EN.book Page 34 Wednesday, January 6, 2010 10:05 PM 5 Select the digital (DVB) / analogue (ATV) mode or external input (AV1/AV2) using [K \ L], then press [1]. 6 Select the channel number to record using [K \ L], then press [1]. 7 Select the recording media (“DVD” or “VCR”) using [K \ L], then press [1]. 8 Select the recording mode using [K \ L], then press [1]. Refer to “Recording Mode” on page 28 for DVD or page 70 for VCR.
E9TK4BD_EN.book Page 35 Wednesday, January 6, 2010 10:05 PM 1 2 E23–E24 Unrecordable disc E25/E51 • Copy prohibited programme • Cannot record because of the NTSC / PAL-60 signal is received. “Timer Programming” list will appear. E26–E28 Copy prohibited programme A) To delete the timer programme: 1) Select the programme you want to delete using [K \ L], then press [ENTER\OK]. 2) Select “Delete” using [K \ L], then press [ENTER\OK]. Confirmation window will appear.
E9TK4BD_EN.book Page 36 Wednesday, January 6, 2010 10:05 PM • If the Start time is earlier and the End time is later than the current time, the recording will start immediately after you press [TIMER SET]. • If a videotape ends during the timer recording, the unit will automatically stop, eject the videotape, and turn itself off. To continue recording, insert a recordable tape. If the End time of the programme currently being recorded and the Start time of the subsequent programme are same: • If PROG.
E9TK4BD_EN.book Page 37 Wednesday, January 6, 2010 10:05 PM Video VR 1 While viewing a DVB programme, press [GUIDE]. • List of DVB programmes will be displayed. 2 Select a desired programme using [K \ L \ 0 \ 1], then press [YELLOW]. 3 You can set the unit to start recording whenever it detects the video scart control from the external tuner. Preparing for the Satellite Link Timer Recording: Press [BLUE] or [ENTER\OK]. Series List 13:12 Mon 17/05 S.No.
E9TK4BD_EN.book Page 38 Wednesday, January 6, 2010 10:05 PM Note General Setting • If you have not set the clock, the clock setting window will appear and follow to “ Clock Setting” on page 67. • You cannot set the End time for the satellite link timer recording on this unit. • [SAT.LINK] does not work under the following circumstances: - Setup menus are displayed. - “Timer Programming” menu is displayed. - Title list or any file list is displayed. - During playback of DVD or VCR.
E9TK4BD_EN.book Page 39 Wednesday, January 6, 2010 10:05 PM The following instructions are described with the operations using the remote control of this unit. 1 2 • “DV Audio” can be changed. With “DV Audio” selected, press [ENTER\OK] to display “DV Audio” menu. Select the audio you want to output using [K \ L], then press [ENTER\OK]. - Select “Stereo1” to dub the stereo sound. - Select “Stereo2” to dub the sound that was added after the recording. - Select “Mix” to dub the stereo1 and stereo2.
E9TK4BD_EN.book Page 40 Wednesday, January 6, 2010 10:05 PM To stop dubbing: DVC to DVD Dubbing Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R Before recording from DVC, see page 19 for connection instructions. (See page 71 for DVC to VCR Dubbing.) Preparing for DV dubbing (DVC to DVD): • Insert a recordable DVD. • Make sure your DVC is in video mode. Press [DVD] first. 1 Press [INPUT SELECT F] repeatedly to select the external input channel, then press [PROG. G \ H] repeatedly to select DV(AV3).
E9TK4BD_EN.book Page 41 Wednesday, January 6, 2010 10:05 PM Dubbing Mode Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R VCR Note for recording to a videotape: Note for recording to a disc: • The DVD disc is satisfied with the recording status. See pages 28 to 29. Insert a disc and a videotape with a record tab. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 42 Wednesday, January 6, 2010 10:05 PM Setting a Disc to Protect VR To cancel finalising (DVD-RW disc only): At step 4, press [STOP C]. Select “Yes” using [K \ L], then press [ENTER\OK]. Finalising is cancelled and the unit switches to stop mode. DVD-RW DVD+RW DVD+R To prevent accidental over-recording, editing or erasing of recordings, you can protect them using “Setup” menu. Do you want to cancel? Yes No Insert a recordable disc. 1 In stop mode, press [SETUP].
E9TK4BD_EN.book Page 43 Wednesday, January 6, 2010 10:05 PM Introduction Playback Note Note for DVD Playback The contents of a DVD are generally divided into titles. Titles are further subdivided into chapters depend on Auto Chapter setting (See page 31). Stop Rec./Start Rec. Title 1 Stop Rec.
E9TK4BD_EN.book Page 44 Wednesday, January 6, 2010 10:05 PM Playing Back an Audio CD or a Disc with MP3 / JPEG / DivX® Files CD MP3 JPEG DivX ® 1 Follow steps 1 to 5 in “Playing Back a DVD-RW / DVD-R / DVD+RW / DVD+R Disc” on page 43. 2 If you want to play back an audio CD or a disc with a single file type (e.g., a disc containing MP3 files only), skip to step 4. If you want to play back a disc with mixed file types, proceed to step 3.
50_Playback.fm Page 45 Friday, January 8, 2010 11:14 AM 2 ® You can play back the contents in a USB device. Note for DivX® • DivX® files recorded in USB device are not guaranteed to play back. Follow the step 4 in “Playing Back an Audio CD or a Disc with MP3 / JPEG / DivX® Files” on page 44. DivX® Subtitle The subtitle created by the user can be displayed during DivX® playback. 1 After the DivX® file is selected, “Subtitle List” will appear.
50_Playback.fm Page 46 Friday, January 8, 2010 3:54 PM DivX® VOD DivX ® This unit allows you to play back the files purchased or rented from DivX® Video-On-Demand (VOD) services. The files are available on the Internet. When you purchase or rent DivX® VOD files on the Internet, you will be asked to enter a registration code and a deactivation code. This menu items provide you with the both codes. 1 2 3 4 Press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 47 Wednesday, January 6, 2010 10:05 PM Please push ‘TOP MENU’. Press [DVD] first. 1 Press [DISC MENU]. If the feature is not available, “ ” may appear on the TV screen. The displayed disc menu, which will vary among discs, and may be same with the Title menu. Select an item using [K \ L \ 0 \ 1], then press [ENTER\OK]. Repeat this step until all the features you want are set up or to start playing back the disc from the menu. The following operation is available.
E9TK4BD_EN.book Page 48 Wednesday, January 6, 2010 10:05 PM Cancelling and Recalling the PBC Function Fast Forward / Fast Reverse DVD-V VCD DVD+R (PBC OFF) 1 Insert a video CD. 1 In stop mode, press [SETUP]. 2 Select “DISC Playback Mode” using [K \ L], then press [ENTER\OK]. 3 Select “PBC (Video CD only)” using [K \ L], then press [ENTER\OK]. Select “OFF” using [K \ L], then press [ENTER\OK]. 5 Press [SETUP] to exit.
E9TK4BD_EN.book Page 49 Wednesday, January 6, 2010 10:05 PM VR DVD-V DVD-RW DVD-RW DVD+R VCD DivX Zoom DVD-R DVD+RW ® During playback, press [PAUSE F]. Press [SKIP H \ G] repeatedly. Each time you press [SKIP G], playback will go forward one frame (or step) at a time with the sound muted. To go backward one frame (or step), press [SKIP H]. Video VR DVD-V DVD-RW DVD-RW DVD+R VCD JPEG DivX During playback, press [DISPLAY] to bring up the display menu.
E9TK4BD_EN.book Page 50 Wednesday, January 6, 2010 10:05 PM Using the [TIME SLIP] button Note • To clear a marker, select the marker number you want to clear, then press [CLEAR]. • You can mark up to 6 points. • All markers are erased when you perform the following operations. - Opening the disc tray - Turning off the power - Making additional recording on the disc (DVD only) - Editing any title (DVD only) - Changing the mode between Original and Playlist.
E9TK4BD_EN.book Page 51 Wednesday, January 6, 2010 10:05 PM The resume message will appear. 1/ 5 1/ 5 Title Search 3 0:01:00 / 1:23:45 -RW VR ORG 1 BBC1 Introduction 3 Press [STOP C] once to stop playback. Enter the desired title number to search for using [K \ L] or [the Number buttons], then press [ENTER\OK]. Title search will start. Note Resume ON LP 1:01 To stop recording, press [STOP C] again. To cancel the resume, press [STOP C] again.
E9TK4BD_EN.book Page 52 Wednesday, January 6, 2010 10:05 PM Title: The current title will be played back repeatedly. (DVD only) Direct Search CD You can search the desired track directly. Chapter: The current chapter will be played back repeatedly. (DVD only) Using [the Number buttons] 1 During playback, if the display menu is not displayed, press [the Number buttons] to enter the desired track number. All: The current disc will be played back repeatedly.
E9TK4BD_EN.book Page 53 Wednesday, January 6, 2010 10:05 PM Programme Playback 4 Select the display time using [K \ L], then press [ENTER\OK]. 5 Press [SETUP] to exit. Note • Large-size JPEG files take a few moments to be displayed. Selecting the Format of Audio and Video Basic Setup / TV View Operation You can select the format of audio and video to suit the content of the disc you are playing back. VCD CD Select “Slide Show” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book 3 Page 54 Wednesday, January 6, 2010 10:05 PM Select a desired audio soundtrack or audio channel using [K \ L], then press [ENTER\OK]. With a DVD-video, VR mode DVD-RW, or DivX® files: Audio soundtrack will switch. Example: English J Spanish J French If the title contains both main and sub audio, you can further select L (main), R (sub), L/R (mixed of main and sub). With an audio CD or video CD: The Audio channel will switch.
E9TK4BD_EN.book Page 55 Wednesday, January 6, 2010 10:05 PM 1 Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer. Press [DVD], then press [TOP MENU].
E9TK4BD_EN.book Page 56 Wednesday, January 6, 2010 10:05 PM Deleting Titles Editing Discs You will find editing discs is easy. This unit offers convenient edit functions. You can edit the following from a title list.
E9TK4BD_EN.book Page 57 Wednesday, January 6, 2010 10:05 PM Video Guide to Editing Title Names VR DVD-RW DVD-R DVD-RW DVD+RW DVD+R You can edit the title names from this menu. The title names you edit will appear on the title list. Press [DVD] first. Step 2 : Using the list below as a guide, press [the Number buttons] repeatedly until the desired letter appears. In stop mode, press [TOP MENU]. Select Press “Title List” will appear.
E9TK4BD_EN.book 5 6 Page 58 Wednesday, January 6, 2010 10:05 PM Select “Yes” using [K \ L], then press [ENTER\OK]. Hiding Chapters Adding a chapter mark: If you select “Add” at step 4, a new chapter mark is created at the point you specified. DVD+RW DVD+R You can hide chapters from the title list. Hidden chapters are skipped during playback. Deleting a chapter mark: If you select “Delete” at step 4, the chapter mark you selected is deleted.
E9TK4BD_EN.book Page 59 Wednesday, January 6, 2010 10:05 PM Writing onto the disc starts. It may take awhile to write the data on a disc. VR DVD-RW Press [RETURN/BACK] to exit. DVD+RW Note Playlist You can divide a title into two new titles. Press [DVD] first. Follow steps 1 to 3 in “Editing Title Name” on page 57. 2 Use [SKIP H \ G], [REV E], [FWD D], [PLAY B] and [PAUSE F] to find where you want to divide the title.
E9TK4BD_EN.book Page 60 Wednesday, January 6, 2010 10:05 PM Deleting All Playlists Deleting Parts of Titles VR VR DVD-RW All Playlists can be deleted if it is no longer needed. 1 2 3 Press [SETUP]. DVD-RW You can delete a specific part of a title. Even when a title is deleted from the Playlist, the original title will remain as it is. The available recording time on the disc will not increase. Select “DVD Menu” using [K \ L], then press [ENTER\OK]. Press [DVD] first.
E9TK4BD_EN.book Page 61 Wednesday, January 6, 2010 10:05 PM Introduction Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Items (highlight is the default) Parental Lock E Page 64 Audio Out Dynamic Range E Pages 64-65 Control PCM MPEG 48kHz 96kHz PCM Stream PCM Stream Set whether the sound recorded in 96kHz will be down sampled to 48kHz.
E9TK4BD_EN.book Setup Recording Page 62 Wednesday, January 6, 2010 Items (highlight is the default) Auto Chapter E Page 31 Recording Audio Select (XP) E Page 32 Auto Finalise E Page 42 Aspect Ratio (Video mode) E Page 30 Dubbing Mode E Page 41 Make Recording Compatible E Page 30 Bilingual Recording Audio E Page 32 External Input Audio E Page 31 Video Colour System E Page 38 10:05 PM Contents Insert chapter marks periodically.
E9TK4BD_EN.book Page 63 Contents Set the colour space for the HDMI output. RGB YCbCr ON OFF Set whether to output the HDMI audio signal or not. Normal Enhanced ON OFF English Gaelic Welsh Set the black-white contrast level for HDMI RGB output. Set the Adult Lock and change Pincode. Subtitle English Gaelic Welsh Set the Subtitle language. Data Service English Gaelic Welsh Set the Digital Teletext language.
E9TK4BD_EN.book Page 64 Wednesday, January 6, 2010 10:05 PM Playback Setup A General Setting A Playback A password is already set 1 Enter the current password using [the Number buttons]. Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System Password Input 2-A Select “No” using [K \ L], then press [ENTER\OK]. Change Password? Parental Lock (Default: OFF) (DVD only) Yes No “Parental Lock” level is activated. Set “Parental Lock” level.
E9TK4BD_EN.book Page 65 Wednesday, January 6, 2010 10:05 PM PCM 48kHz 96kHz Disc Menu Language (Default: English) (DVD only) Introduction PCM sampling (Default: 48kHz) Set “Disc Menu Language”. Disc Menu Language : If your amplifier / decoder is NOT compatible with 96 kHz PCM, select “48kHz”. Sound recorded at 96 kHz is down sampled to 48 kHz. 96kHz : If your amplifier / decoder is compatible with 96 kHz PCM, select “96kHz”. Sound is sampled at 96 kHz.
E9TK4BD_EN.book Page 66 Wednesday, January 6, 2010 10:05 PM Still Mode (Default: Auto) (DVD only) Still Mode Display Setup A General Setting A Display Auto Field Frame Auto : Automatically select the best resolution setting (“Frame” or “Field”) based on the data characteristics of the pictures. Field : Select “Field” when the pictures are still unstable even if “Auto” is selected. “Field” stabilises the pictures, although the picture quality may become coarse due to the limited amount of data.
E9TK4BD_EN.book Page 67 Wednesday, January 6, 2010 10:05 PM Introduction 3 Select “Yes” using [K \ L], then press Video [ENTER\OK] within 15 seconds. Setup A General Setting A Video Confirm again to use progressive scan. If picture is good, select “Yes”. TV Aspect Video Out Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture. TV Aspect Video Out (Default: SCART (RGB)) press [ENTER\OK].
E9TK4BD_EN.book Page 68 Wednesday, January 6, 2010 10:05 PM Auto Clock Setting (Default: ON) This unit receives time signals from the analogue / DVB channels, and set the clock automatically. Set the channel tuning before setting Auto Clock. Auto Clock Setting ON OFF HDMI Setup A General Setting A HDMI • Make sure that the HDMI cable is connected and the TV input is set to HDMI. Format HDMI Audio RGB Range 1 Select “ON” using [K \ L], then press [ENTER\OK]. 2 Press [SETUP] to exit.
E9TK4BD_EN.book Page 69 Wednesday, January 6, 2010 10:05 PM Setup A General Setting A DVB Setting You can make settings of the digital tuner from the DVB Setting. DVB Language Audio Subtitle Data Service Audio : Set the Audio language. Subtitle : Set the Subtitle language. Connections Adult Lock Language About Adult Lock (Default: OFF) Introduction Language DVB Setting Data Service : Set the Digital Teletext language. DVB Note 1 Select “ON” or “OFF” using [K \ L], then press [ENTER\OK].
E9TK4BD_EN.book Page 70 Wednesday, January 6, 2010 10:05 PM VCR Functions Common Procedures 1 Press [B ON\STANDBY] to turn on the unit. To play back a tape, turn on the TV and be sure to select the input to which the unit is connected. 2 Basic Recording and One-touch Timer Recording (OTR) VCR Press [VCR].
E9TK4BD_EN.book Page 71 Wednesday, January 6, 2010 10:05 PM One-touch Timer Recording will start. 0:30 8:00 This function helps you to dub the contents in the DVC (digital video camcorder) to VCR. Preparing for DV dubbing (DVC to VCR): 1:00 • Insert a recordable videotape. • Make sure your DVC is in video mode. Press [INPUT SELECT F] repeatedly to select the external input channel, then press [PROG. G \ H] repeatedly to select DV(AV3). 2 Select the recording mode using [REC MODE]. (See page 70.
E9TK4BD_EN.book Page 72 Wednesday, January 6, 2010 10:05 PM Time Search VCR This feature allows you to go to a specific point on a tape by entering the exact amount of time you want to skip in order to reach the point. 1 Press [SEARCH] repeatedly until the time search menu appears. 2 Enter your desired time to skip using [the Number buttons] within 30 seconds. 3 Press [FWD D] or [REV E] to start time search. If you want to go in the forward direction, press [FWD D].
E9TK4BD_EN.book Page 73 Wednesday, January 6, 2010 10:05 PM Introduction Others Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. • Check that the AC power cord is connected securely. • Batteries of the remote control are weak. • Press [TIMER SET] to cancel the timer-standby mode.
E9TK4BD_EN.book Page 74 Wednesday, January 6, 2010 Symptom Remedy CHANNEL TV channels cannot be changed. • Check if the connections are made securely and correctly. • Check if the cables are damaged. • Try “Channel” setting by following the steps on pages 20-22. Some settings are lost even though you • If you unplug the AC mains cable while the warning message, “Saving settings. followed the procedure correctly. Please wait.”, is displayed, some settings may be lost.
E9TK4BD_EN.book Page 75 Wednesday, January 6, 2010 10:05 PM Remedy GENERAL • Check if all the connections are made correctly. • Check if the “Audio Out” is set correctly. (See pages 64-65.) • There is a possibility that the selected subtitle language is not supported by the disc. Digital audio setting cannot be changed to main audio (L), sub audio (R) or combination of both. • If the audio source is in the Dolby Digital format, set “Dolby Digital” setting to “PCM” in “Playback” menu.
DVD EDITING E9TK4BD_EN.book Page 76 Wednesday, January 6, 2010 Symptom Remedy Titles cannot be edited or deleted. • The titles or the disc itself may be protected. Cancel the protection by following the steps on page 58 for title protection and page 42 for disc protection. Dubbing cannot be executed. • When the number of the titles or the chapters exceeds the maximum recordable number, the dubbing will not be executed. Titles cannot be edited or deleted.
90_Others.fm Page 77 Friday, January 8, 2010 3:54 PM Cause Introduction Error message Solution • Insert a recordable disc with enough recording space. • Delete unnecessary original titles. (See page 56.) Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99) • You are trying to record onto the DVD-RW / -R disc on which the number of recorded titles has reached the maximum (99). • Delete unnecessary original titles. (See page 56.
E9TK4BD_EN.
90_Others.fm Page 79 Friday, January 8, 2010 11:13 AM Introduction Specifications General Four heads Power requirements 220–240 V Power consumption 35 W Power consumption (standby) 0.95 W Weight 4.9 kg ± 10 %, 50 Hz ± 0.5 % 435 x 99.
E9TK4BD_EN.