INSTRUCTION MANUAL CCD COLOR CAMERA IK-65WDA Please read this manual thoroughly before use, and keep it handy for future reference. Record in space provided below the Model No. and the Serial No. as found on the bottom of this unit. Model No. IK-65WDA Serial No. ____________ Retain this information for future reference. TABLE OF CONTENTS Important Safeguards 1. Features & Description ······································································· 4 2.
IMPORTANT SAFEGUARDS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions The safety instructions and instruction manual should be retained for future reference. 12. Lightning For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system.
The CAUTION label, shown on the left, is attached on the bottom of camera. The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
1.FEATURES & DESCRIPTION : (1) IK-65WDA has the following functions. (1) 133 Times Dynamic Range Toshiba developed algorithms that enable industry leading dynamic range (2) Digital Noise Reduction (“DNR”) Exclusive 3 Dimensional Digital Noise Reduction boosts S/N ratio to a incredible 53dB (3) 0.001Lux @ 1.
SHUTTER / WDR / BLC GAIN / ALC / SHARPNESS WHITEBAL / ID.etc. Rear View Remote terminal: Connect to keyboard AC 24V ~ /DC 12V by RS422 power terminal V PHASE: Line-Lock Phase adjustment trimmer Video output terminal connect to a TV monitor, etc. Dip switch settings LINE LOCK : ON/OFF IRIS : AES/DC WDR : ON/OFF DN : MID / S.DN x 32 4.
5.CONNECTIONS AND OPERATIONS : Notes on connecting • Power plugs of connected equipment must be disconnected before installations. • A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection. • For details of wiring and operation of equipment to be connected, refer to their operation manuals. • Lenses, coaxial cables for video signals and the power cord are not supplied with the camera.
5.2 Line-Lock Control • Matching the vertical synchronization with the power frequency is called the Line-Lock. • This function is activated when the LINE LOCK switch is selected to ON. • When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync. Phase can be locked with the power frequency, and a stable vertical sync. Is obtained without being disturbed at the time of switching.
5.4 Back focus adjustment: Back focus is adjusted at the factory to accommodate most standard lenses. If a slight adjustment is needed, mount the lens to the camera first. Then loosen the Focus Lock Screw. Rotate the Focus ring until a clear image is achieved. Retighten the Focus Lock Screw. NOTE • When the lens weight is more than 2.2 lbs., support the camera on the lens side rather than relying on the tripod mount of the camera. 5.
6.LINE-LOCK PHASE : When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller (on rear panel) to get a stable image. The camera is in the Line-Lock Mode. Line-Lock phase is set 0-300 degrees by adjusting the V phase control at the rear of the camera. V. PHASE CONTROLLER 7.DIP SWITCH SETTINGS : The following settings can be performed by setting the rear dip switches. 7.
7.4 DN (DIP4) : MID/S.DNx32 DN mode select switch. MID (ON side) : In low light conditions the IK-65WDA automatically cuts the chroma signal and boots the gain up of the luminance by 6dB. S.DN×32 (OFF side) : Under the low light condition, the IK-65WDA automatically activates the slow shutter function. FACTORY SETTINGS LINE LOCK : ON IRIS : DC WDR : OFF DN : S.DN×32 NOTE • When you change DIP 2, 3 or 4 then the present settings are displayed for about 2 seconds on the upper left side of the screen.
8.MENU DRIVEN SET-UP : The following is the on-screen menu (“OSD”) structure for all settings and adjustments of the camera. RS422 setting menu ADDRESS 001~255 MENU PROTOCOL TOSHIBA-P BIT-RATE 1200 2400 VERSION **************** TOSHIBA-D 4800 9600 EXIT DEFAULT MAIN menu (Except for DIP3 and DIP4 ON) ALC –99~99 BLC OFF AUTO CENTER1/3 GAIN MENU ID.
ADVANCED MAIN menu (DIP3 and DIP4 ON) SHUTTER NO-D/N D/N LOW MID HIGH S. D/N x128 x64 x32 x16 x4 x2 x1 WDR OFF ALC –99~99 BLC OFF ON AUTO UPPER2/3 CENTER1/3 MENU LOWER2/3 CENTER1/6 GAIN OFF STD HIGH SHARPNESS LOW MID HIGH WHITE BAL AUTO: –20~20 R: –99~99 B: –99~99 SIDE1/6 B: INDOOR1 INDOOR2 OUTDOOR ID. OFF TOP PTN-GEN OFF COLOR AWB-RNG STD WIDE DNR LOW HIGH HI-RESO OFF ON CANCEL DEFAULT 12 ........... ID.
8.1 Setting switches and the functions On the side panel of the cameras there are three push button switches as shown below: Switch name Select Main function Setting mode call on/off, setting entry Setting item selection (down) Setting item selection (up) 8.2 On Screen MAIN menu (Except for DIP3 and DIP4 ON) The camera is adjusted using the On Screen Menu. Press and hold the select switch on the side of the camera body 2 seconds until the menu appears on the monitor.
(4) BLC = Back light compensation Move the cursor to the position in Fig. Use the SELECT switches to select OFF, AUTO, UPPER2/3, LOWER2/3, CENTER1/ 3, CENTER1/6, LOWER1/6 Using in AES or auto iris lens, the exposure adjustment is automatically controlled so that the best picture is obtained at next monitor zone. This function is effective when strong light enters and auto iris lens closes. OFF:The camera is not in BLC mode. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. . . . .
(5) GAIN = AGC gain setting Move the cursor to the position in Fig. Use the SELECT switches to select OFF, STD, HIGH. OFF : AGC does not operate. STD : Standard position, max gain = 24dB HIGH : High-Sensitivity position, max gain = 30dB (If there is noise in low light conditions, set to STD.) WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. . . . . . . . . . . . . . . I D - POS OF F DIP DIP 00 SW SW . . . . . .
(8) CANCEL Move the cursor to the position in fig. Press the SELECT switch to exit the menu without saving and changes. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. . . . . . . . . . . . . . . I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T (9) EXIT Move the cursor to the position in fig. Press the SELECT switch when SAVE ALL SETTING (excluding WDR, D/N settings) is displayed to save all changes and exit the menu.
8.3 On Screen ADVANCED MAIN menu (DIP3 and DIP4 ON) The camera is adjusted using the On Screen Menu. Press and hold the select switch on the side of the camera body 2 seconds until the menu appears on the monitor. The shaded area represents the option to be set. (Displayed when both DIP3 and DIP4 on the rear are set to ON.
(2) WDR = Wide dynamic range function Move the cursor to the position shown in fig. Use the SELECT switches to select OFF or ON in the WDR setting. When WDR is set to ON, WDR activates automatically. When WDR function is activated, the video of each field is mixed. When this happens, vertical resolution and the number of the frames decrease slightly.
(7) WHITE BAL (WHITE BALANCE) Move the cursor to the position shown in fig. Use the SELECT switches to select AUTO, MANUAL in the WHITE BAL settings. S HU T T E R WD R ALC BLC GA I N S HAR P N E S S WH I T E - B A L D / N :MI D ON LEV : 0 0 AUTO S TD MI D AUTO : 0 0 AUTO : The white balance is automatically adjusted corresponding to the color temperature variations on the object. The camera is applicable to a color temperature range of 2500NEXT 10K.
(10) PTN-GEN = Test pattern generator Move the cursor to the position shown in fig. MULTI 7.2MHz GRID 3.6MHz Red STEP Blue Black Megenta Cyan Green White Yellow COLOR B ACK EX I T CANCE L DE F AUL T 1.8MHz Test pattern is not displayed. Color bar signal is displayed. Gray step signal is displayed. Grid pattern signal is displayed. A simple multi-burst signal is output. 0.9MHz : : : : : 0.22MHz OFF COLOR STEP GRID MULTI ID . . . . . . . . . . . . . . . . . . . .
(12) DNR = Digital noise reduction Move the cursor to the position shown in fig. Use the ▲ ▼ SELECT switches to select LOW, HIGH, SUPER. LOW : Standard position. HIGH : Increase the effect of DNR. SUPER : Further increase the effect of DNR. NOTE • If you set HIGH or SUPER the noise reduction effect is reduced but an after-image is produced if a moving subject is shot. ID . . . . . . . . . . . . . . . . . . . .
(14) NEXT, BACK Move the cursor to the position in fig. Press the SELECT switch, to select the last page or next page. S HU T T E R WD R ALC BLC GA I N S HAR P N E S S WH I T E - B A L D / N :MI D ON LEV : 0 0 AUTO S TD MI D AUTO : 0 0 NEXT EX I T CANCE L DE F AUL T ID . . . . . . . . . . . . . . . . . . . . I D - POS OF F P TN - GEN OF F AWB - R N G S TD DNR L OW H I - RE SO OF F B ACK EX I T CANCE L DE F AUL T (15) CANCEL Move the cursor to the position in fig.
(16) EXIT Move the cursor to the position in fig. Press the SELECT switch when SAVE ALL SETTINGS is displayed to save all changes and exit the menu. S HU T T E R WD R ALC BLC GA I N S HAR P N E S S WH I T E - B A L D / N :MI D ON LEV : 0 0 AUTO S TD MI D AUTO : 0 0 NEXT EX I T CANCE L DE F AUL T (17) DEFAULT Move the cursor to the position in Fig. Press the SELECT switch to select DEFAULT, which returns the camera to its factory settings.
8.4 On Screen RS422 setting menu (FOR REMOTE CONTROL) The camera is adjusted using a sub menu for setup using a remote control. Press and hold the switch on the side of the camera body 2 seconds until the menu appears on the monitor. The blinking area represents the option to be set. (This sub menu cannot control from a keyboard by RS-422) Default settings ADDRE S S P ROTOCOL B I T - RAT E 001 TO S H I BA - P 4800 (1) ADDRESS Move the cursor to the position in Fig.
9.REMOTE CONTROL : RS-422 Control (Factory-setting) supported TOSHIBA-P and TOSHIBA-D. Rx Rx G Camera terminal Twisted pair line Rx- Tx- 2 wires Control Tx+ Rx+ Tx of the communication line from KBD is connected to Rx of the camera, and Tx-is connected to Rx-of the camera. A controllable function is as follows.
10. NOTES ON USE AND INSTALLATION : • Do not aim the camera at the sun Do not aim the camera at the sun or point it at sun even if you are not shooting. • Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction. • Treat the camera with care Do not drop the camera or subject it to strong shock of vibration. Otherwise, the camera may malfunction.
11. IN CASE OF PROBLEMS : Condition No image Unnatural color • • • • • Check Points Are the camera and connected equipment turned on? Is the iris of the lens adjusted properly? Are cables connected correctly? Is the monitor TV adjusted correctly? Is the lighting too weak? Press default to return the camera to factory settings (8.2.
12. SPECIFICATIONS : Power AC 24V ~ ± 10% 60Hz/DC 12V Power consumption 6.0W with AI lens Image sensor 1/3 inch CCD image area sensor Image pickup area 5.59mm (0.220inch) horizontal x 4.68mm (0.184inch) vertical (1/3inch type) Effective picture element 768 horizontal x 494 vertical Scanning system 2 : 1 interlace NTSC Standard TV system Scanning frequency 15.
13.
Memo 31