CAMILEO® BW10 Quick Start Guide English/Español
Introduction For more detailed information please refer to the User's Guide on the included CD. Safety instructions 1 Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided. 2 Do not expose the camcorder to high temperature or leave it in direct sunlight. Doing so may damage the camcorder. 3 Use the camcorder with care. Avoid pressing hard on the camcorder body. 4 For your own safety, avoid using the camcorder when there is a storm or lightning.
Waterproof* feature 3 ❖ Never install or remove the battery without first turning off the power and disconnecting the USB cable. ❖ Only use the supplied USB cable or a generic standard USB AC adaptor (not supplied by Toshiba). Never attempt to charge the battery with anything other than the above chargers specified. Waterproof* feature This camcorder complies with Japanese Industrial Standards (JIS) IPX8 (formerly JIS protection grade 8) waterproof standard and can be used in water.
Waterproof* feature Cautions concerning use in water ❖ The waterproof properties of the camcorder apply to fresh water and saltwater only; they do not apply to cleaning substances, chemicals or water from spas, etc. In case of a splash, immediately wipe off any moisture. ❖ Do not immerse in water at a depth greater than 6.56 ft. (2.0m). ❖ Do not subject the camcorder to high-pressure water. ❖ Do not immerse in water for longer than 60 minutes.
Waterproof* feature 5 Storing and maintaining your camcorder ❖ Do not leave the camcorder unwashed after it has been immersed in salt water or if salt water is adhering to it. Doing so may cause corrosion and discoloration of the plating, as well as deterioration of the camcorder’s waterproof capability. ❖ After the camcorder has been used in water, use fresh water to wash it. Never use soap or detergent to clean the camcorder, as doing so will cause deterioration of the camcorder’s waterproof capability.
Waterproof* feature Before recording in water Make sure that the slot cover and the port cover are closed. If a cover is open, water will get inside the camcorder and damage it. When closing the slot cover and port cover, make sure that no foreign object such as sand, hair, dust, etc. is caught in the rubber seal. There are places in the camcorder where water might accumulate, but this will not affect its waterproof properties.
Waterproof* feature 7 Contact Address: TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 Additional Information © Copyright 2011 TOSHIBA CORPORATION. All rights reserved. TOSHIBA reserves the right to make technical changes. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between this product and the documentation.
Getting Started Getting Started Loading the battery Before using the camcorder, remove the protective film from the battery as shown below. (Sample Illustration) Removing the protective film from the battery Inserting the battery To install the supplied battery: 1 While pressing down on the slot cover release latch, slide the slot cover out and open.
Getting Started 2 9 Insert the battery until it locks into place. (Sample Illustration) Inserting the battery 3 Close the battery/media card slot cover. Secure it by sliding it back into place. (Sample Illustration) Closing the battery/media card slot cover Close the slot cover and port cover securely. If any cover is not closed or is not closed completely, the camcorder will no longer be waterproof. When closing a cover, make sure that no foreign object such as sand, hair, dust, etc.
Inserting and removing a media card Inserting and removing a media card Your camcorder comes with internal memory that allows you to store photos and videos. The images you capture are saved to the camcorder’s internal memory. You can expand the memory capacity by using an optional media card. The Media card reader supports the use of Secure Digital™ (SD™), SDHC™ (High Capacity), and SDXC™ (Extended Capacity) Memory Cards. When a card is installed, images are recorded to and played back from the card.
Inserting and removing a media card 3 11 To remove an installed media card, gently press the card inward to release it. The card pops out slightly. 4 Pull the card straight out. (Sample Illustration) Removing the media card 5 Close the battery/media card slot cover. Secure the cover by sliding it back into place. Close the slot cover and port cover securely. If any cover is not closed or is not closed completely, the camcorder will no longer be waterproof.
Charging the battery Charging the battery You must use the supplied USB cable or a generic standard USB AC adaptor (not supplied by Toshiba) to charge your camcorder before use. The camcorder should be OFF. A solid light will indicate active charging. When the light turns off, charging is complete. ❖ Do not turn on the camcorder while the battery is charging. It is not possible to charge the battery while the camcorder is on. ❖ Do not turn off the computer while the battery is charging.
Charging the battery 1 To charge the battery, the camcorder must be OFF. If the camcorder is ON, press the Power button for at least one second to turn it off. Power button (Sample Illustration) The Power button 2 Slide the port cover latch to the open position. The port cover swings open.
Charging the battery 3 Use the dedicated USB interface cable (supplied) to connect the camcorder to a computer. (Sample Illustration) Connecting to a computer 4 Turn on the computer to begin charging the camcorder. The multi-indicator light glows orange. 5 ❖ The indicator light turns off when charging is complete ❖ Charge time is approximately 220 minutes When charging is complete close the port cover, ensuring that it closes tightly.
Quick Tour 15 Quick Tour Front view (record and play) 1 To power on: 3 Dual record: Press and hold the Power ( .....) button for one second. To conserve battery power, the camcorder will turn off automatically after one minute of non-operation. When recording a video, press the Photo ( ...) button to capture a still image. 4 To take photos: 2 To start or stop recording: Press the Video ( ...) button to start/stop recording. NOTE: The Video ( ...) indicator appears on the screen.
Setting the date and time Rear view Microphone LED light Lens Port cover Battery/Media card slot cover (Sample Illustration) Rear view Setting the date and time If the Settings Menu screen appears when you turn on the camcorder, follow steps 1-7 below. When the camcorder is turned on for the first time after purchase, the Clock Set screen appears on the camcorder screen. Follow the steps below to set the date and time, beginning at step 4.
Setting the date and time 3 17 Use the Up/Down arrow buttons to toggle between the selections. Select Clock Set, and then press the OK button. The Clock Set screen appears.
Copying files to a computer Under normal conditions, while replacing the battery, the internal battery will maintain the date and time settings. However, there is a small chance the settings may be lost (the internal battery backup will last for approximately seven days). It is recommended to check that the date and time settings are still correct after replacing the battery and before taking photos or recording of any type.
Copying files to a computer 3 19 Connect the other end of the cable to a computer. USB cable (Sample Illustration) Connecting a USB cable to the camcorder and computer 4 Press the Power button for approximately one second to turn on the camcorder. The USB Connection screen appears on the camcorder’s screen.
Copying files to a computer 5 Select COMPUTER, and then press the OK button. The Computer Connection Mode screen appears. USB CONNECTION YouTube CARD READER MTP PC CAMERA CANCEL CANCEL OK OK (Sample Image) Computer Connection Mode screen 6 Select CARD READER, and then press the OK button. 7 Copy the desired camcorder file(s) from your camcorder to the computer. To access the data in the camcorder’s internal memory, remove the card from the camcorder.
Toshiba Support 21 Application software The following software is bundled on the included DVD-ROM: ❖ CAMILEO® Uploader: With this application installed and while your camcorder is connected to your computer in the YouTube® mode, the camcorder is ready to upload files to YouTube®. ❖ MAGIX Video deluxe 15 Plus Trial Software: This software can be used to edit videos (30-day trial version).
Toshiba Support Toshiba voice contact For technical support, call the Toshiba Customer Support Center: Within the United States at (888) 592-0944 Outside the United States at (949) 583-3305 Toshiba Phone Service Center for Latin America Specialized technical service in Spanish. Hours: Monday through Friday from 8:00 a.m. to 9:00 p.m.
CAMILEO® BW10 Guía de inicio rápido
2 Introducción Para obtener información detallada consulte el Manual del usuario en el CD que se incluye. Instrucciones de seguridad 1 No deje caer la videocámara ni la perfore o desarme, de lo contrario se anula la garantía. 2 No exponga la videocámara a temperaturas elevadas ni la deje en contacto directo con la luz del sol ya que la videocámara podría averiarse. 3 Use la videocámara con cuidado. No presione el cuerpo de la videocámara con fuerza.
Propiedades de impermeabilidad* ❖ ❖ ❖ 3 Cargue la batería solamente a temperatura ambiente entre 5 y 35 grados centígrados (41 y 95 grados Fahrenheit). De lo contrario, es posible que se fugue la solución electrolítica, que se deteriore el rendimiento de la batería y que se acorte su duración. Nunca instale o extraiga la batería sin antes apagar la alimentación y desconectar el cable USB. Use solamente el cable USB que se suministra o un adaptador USB AC genérico estándar (no suministrado por Toshiba).
4 Propiedades de impermeabilidad* Precauciones relativas al uso de la videocámara en el agua ❖ La propiedad de impermeabilidad de la videocámara se aplica solamente al agua dulce y al agua de mar, pero no a sustancias de limpieza, químicos, aguas termales, etc. En caso de salpicaduras, elimine con un paño cualquier humedad. ❖ No sumerja la videocámara en agua a una profundidad superior a 2 metros (6,56 pies). ❖ No someta la videocámara a agua a alta presión.
Propiedades de impermeabilidad* 5 Almacenamiento y mantenimiento de la videocámara ❖ Lave la videocámara después de sumergirla en agua salada o cuando ha quedado agua salada adherida a la misma. De lo contrario se puede causar la corrosión o descoloración de la lámina, al igual que el deterioro de la impermeabilidad de la videocámara. ❖ Después de utilizar la videocámara en el agua, use agua fresca para lavarla.
6 Propiedades de impermeabilidad* Antes de grabar bajo el agua Asegúrese de que la cubierta de la ranura y la del puerto estén cerradas. Si una cubierta está abierta, el agua podría entrar en la videocámara y dañarla. Al cerrar la cubierta de la ranura y la del puerto, asegúrese de que no quede atrapado en el sello de caucho ningún objeto extraño como arena, pelos, polvo, etc. Hay lugares de la videocámara donde podría acumularse agua, pero esto no afecta la impermeabilidad de la misma.
Propiedades de impermeabilidad* 7 Contacto Dirección: TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Teléfono: (949) 583-3000 Información adicional © Copyright 2011 TOSHIBA CORPORATION. Todos los derechos reservados. TOSHIBA se reserva el derecho de efectuar cambios técnicos. TOSHIBA no asume ninguna responsabilidad por daños directos o indirectos incurridos por errores, omisiones o discrepancias entre este producto y la documentación.
8 Para comenzar Para comenzar Instalación de la batería Antes de usar la videocámara, retire la película protectora de la batería como se muestra a continuación. (Ilustración de muestra) Cómo retirar la película protectora de la batería Inserción de la batería Para instalar la batería que se suministra: 1 Mientras presiona hacia abajo el pestillo de desenganche de la cubierta, deslice la cubierta hacia afuera y ábrala.
Para comenzar 2 Inserte la batería hasta que encaje en su lugar. (Ilustración de muestra) Cómo insertar la batería 3 Cierre la cubierta de la ranura de la batería/tarjeta de medios. Asegúrela deslizándola de vuelta a su lugar. (Ilustración de muestra) Cómo cerrar la cubierta de la ranura de la batería/tarjeta de medios Cierre bien la cubierta de la ranura y la del puerto. Si cualquier cubierta no se cierra o no se cierra bien, la videocámara pierde su impermeabilidad.
10 Inserción y extracción de una tarjeta de medios Inserción y extracción de una tarjeta de medios Su videocámara viene con una memoria interna que le permite almacenar fotografías y películas. Las imágenes que usted captura se guardan en la memoria interna de la videocámara. Usted puede aumentar la capacidad de la memoria utilizando una tarjeta de medios opcional.
Inserción y extracción de una tarjeta de medios 3 11 Para retirar una tarjeta de medios instalada, presione con cuidado la tarjeta hacia adentro para liberarla. La tarjeta sobresale ligeramente. 4 Hale la tarjeta hacia afuera. (Ilustración de muestra) Cómo extraer una tarjeta de medios 5 Cierre la cubierta de la ranura de la batería/tarjeta de medios. Asegure la cubierta deslizándola de vuelta a su lugar. Cierre bien la cubierta de la ranura y la del puerto.
12 Carga de la batería Carga de la batería Para cargar la videocámara antes de usarla use solamente el cable USB que se suministra o un adaptador USB AC genérico estándar (no suministrado por Toshiba). La videocámara debe estar APAGADA. Una luz sólida indica que la batería se está cargando. Cuando la luz se apaga, indica que se completó la carga. ❖ No encienda la videocámara mientras se está cargando la batería. No se puede cargar la batería mientras la videocámara está encendida.
Carga de la batería 1 Para cargar la batería la videocámara debe estar APAGADA. Si la videocámara está ENCENDIDA, presione el botón de encendido durante al menos un segundo para apagarla. Botón de encendido (Ilustración de muestra) El botón de encendido 2 13 Deslice el pestillo de la cubierta del puerto a la posición de abierto. La cubierta se abre.
14 Carga de la batería 3 Use el cable de interfaz USB dedicado (que se suministra) para conectar la videocámara a la computadora. (Ilustración de muestra) Cómo conectar la videocámara a una computadora 4 Encienda la computadora para empezar a cargar la videocámara. La luz del indicador múltiple se ilumina de color naranja. 5 ❖ Cuando se completa la carga la luz del indicador se apaga. ❖ El tiempo de carga es de aproximadamente 220 minutos.
Referencia rápida 15 Referencia rápida Vista frontal (grabar y reproducir) 1 Para encender la computadora: Presione y mantenga presionado el botón de encendido (.... ..) durante un segundo. 3 Grabación dual: Mientras esté grabando un video, presione el botón Fotografía ( ...) para capturar una fotografía. Para conservar energía de la batería, la videocámara se apaga 4 Para tomar fotografías: automáticamente después de un minuto de inactividad. Presione el botón Fotografía ( ...
16 Configuración de la fecha y la hora Vista posterior Micrófono Luz LED Lente Cubierta del puerto Cubierta de la ranura de la batería/tarjeta de medios (Ilustración de muestra) Vista posterior Configuración de la fecha y la hora Si la pantalla del menú Configuración aparece cuando enciende la videocámara, siga los pasos 1-7 que aparecen a continuación. Cuando se enciende la videocámara por primera vez aparece la pantalla Clock Set (Configurar reloj) en la pantalla de la videocámara.
Configuración de la fecha y la hora 3 17 Use los botones de dirección Arriba/Abajo para alternar entre las selecciones. Seleccione Clock Set (Configurar reloj) y luego presione el botón OK (Aceptar). Aparece la pantalla Clock Set (Configurar reloj).
18 Copia de archivos a una computadora NOTA Bajo condiciones normales, la batería interna conserva la configuración de la fecha y la hora mientras se está reemplazando la batería. Sin embargo, existe la posibilidad de que se pierda la configuración (la batería interna de respaldo dura aproximadamente siete días). Después de reemplazar la batería, y antes de tomar fotografías o grabar cualquier cosa, se recomienda verificar que la configuración de la fecha y hora son correctas.
Copia de archivos a una computadora 3 19 Conecte el otro extremo del cable a una computadora. Cable USB (Ilustración de muestra) Cómo conectar un cable USB a la videocámara y a la computadora 4 Presione el botón de encendido durante aproximadamente un segundo para encender la videocámara. En la pantalla de la videocámara aparece la pantalla de conexión USB.
20 Copia de archivos a una computadora 5 Seleccione COMPUTER (Computadora) y luego presione el botón OK (Aceptar). Aparece la pantalla del modo Conexión a computadora. USB CONNECTION YouTube CARD READER MTP PC CAMERA CANCEL CANCEL OK OK (Imagen de muestra) Pantalla del modo Conexión a computadora. 6 Seleccione CARD READER (Lector de tarjeta) y luego presione el botón OK (Aceptar). 7 Copie los archivos que desea transferir de la videocámara a la computadora.
Asistencia técnica de Toshiba 21 Asistencia técnica de Toshiba Si necesita ayuda o tiene problemas con el funcionamiento de su producto, podría ser necesario ponerse en contacto con Toshiba para obtener asistencia técnica adicional. Antes de contactar a Toshiba Puesto que algunos problemas pueden estar relacionados con el software, es conveniente que recurra primero a otras fuentes de asistencia técnica.
22 Asistencia técnica de Toshiba Horas: De lunes a viernes de 8:00 a.m. a 9:00 p.m.