TOSHIBA Satellite A40 Series Portable Personal Computer User’s Manual
Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite A40 Series Portable Personal Computer User’s Manual First edition December 2003 Disclaimer This manual has been validated and reviewed for accuracy.
FCC information Product Name : Satellite A40 Model number : PSA40 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Type of service Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other ent
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed. ❑ The preferred method of dialing is to use DTMF tones (ATDT...
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.
Optical disc drive safety instructions NOTE: Be sure to check the international precautions at the end of this section. TEAC CD-RW/DVD-ROM DW-224E CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2.
DVD Multi DV-W22E CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
TOSHIBA DVD-ROM SD-C2612 CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
DVD-R/-RW SD-R6112 CAUTIONS: 1. The DVD-R/-RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
CD-RW/DVD-ROM SD-R2412 CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
HITACHI DVD-ROM GDR-8082N CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
DVD±RW GWA-4040N CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Pioneer DVD±RW DVR-K12D CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Panasonic DVD Multi UJ-811B CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
CD-RW/DVD-ROM UJDA750 CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3. To prevent direct exposure to the laser beam, do not try to open the enclosure.
International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface Manual contents ........................................................................... xxxiii Conventions .................................................................................. xxxiv Abbreviations ................................................................................... xxxiv Icons ............................................................................................... xxxiv Keys .....................................................................
Slots .................................................................................................. 1-7 Multimedia .......................................................................................... 1-7 Communications ................................................................................. 1-8 Security .............................................................................................. 1-9 Software ...............................................................................
Connecting the AC adaptor .............................................................. 3-5 Opening the display .......................................................................... 3-6 Turning on the power ....................................................................... 3-7 Starting up for the first time .............................................................. 3-8 Turning off the power .......................................................................
CD/DVDs.......................................................................................... 4-16 Diskettes .......................................................................................... 4-17 Sound System .................................................................................. 4-17 Volume control ................................................................................. 4-17 Microphone level ...............................................................................
Chapter 6 Power and Power-Up Modes Power conditions ................................................................................ 6-1 Power indicators ................................................................................ 6-2 Battery indicators .............................................................................. 6-2 DC IN 15V indicator .......................................................................... 6-3 Power indicator ........................................................
Removing an SD card ......................................................................... 8-5 SD card care ...................................................................................... 8-6 Memory expansion ............................................................................ 8-6 Installing memory module ................................................................... 8-7 Removing memory module ................................................................ 8-10 Battery pack .........
Modem ............................................................................................. 9-25 Standby/Hibernation ......................................................................... 9-27 LAN .................................................................................................. 9-27 Wireless LAN ................................................................................... 9-27 i.LINK (IEEE1394) ............................................................................
xxxii
Preface Congratulations on your purchase of the TOSHIBA Satellite A40 computer. This powerful, notebook computer is designed to provide years of reliable, highperformance computing. This manual tells how to set up and begin using your TOSHIBA Satellite A40 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
User's Manual Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
User's Manual xxxvi
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impaired performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
User's Manual PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
Stress injury The cautions on use of a Satellite A40 series computer. 1. Cleaning of the dust accumulated on the cooling vent of the computer. CAUTION: When you use your computer in a dusty area, the dusts accumulate on a cooling vent at the under side of your computer. The accumulated dusts cause insufficient heat dissipation. Clean the dusts off with vacuum cleaner. 2. Cooling vent at the underside of the computer.
User's Manual Open the keyboard brace CAUTION: Memory module and the work of the replacement of the internal modem etc. detach keyboard brace, bases such as speakers and Power buttons become baring. Never touch substrates such as speakers and Power buttons of baring. It causes the breakdown when touching.
Introduction Equipment checklist .......................................................................... 1-1 Hardware ............................................................................................ 1-1 Software ............................................................................................. 1-1 Windows XP Home Edition/Professional ............................................. 1-1 Features ...........................................................................................
INTRODUCTION
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
INTRODUCTION User's Manual • TOSHIBA Power Saver • TOSHIBA Console • Online manual • TOSHIBA Config Free • TOSHIBA Touch and Launch • TOSHIBA PC Diagrotic Tool ❑ Documentation: • • • • ❑ Satellite A40 User's Manual Microsoft Windows XP manual package Instruction Manual for Safety & Comfort End User License Agreement Product Recovery DVD-ROM Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compa
Features which incorporates a 512KB level 2 cache memory. Mobile Intel® Pentium® 4 processor 2.66GHz supporting Hyperthreading Technology(*1) Mobile Intel® Pentium® 4 processor 2.88GHz supporting Hyperthreading Technology(*1) Mobile Intel® Pentium® 4 processor 3.06GHz supporting Hyperthreading Technology(*1) Mobile Intel® Pentium® 4 processor 3.
INTRODUCTION User's Manual Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. See the AC adaptor section in Chapter 2, The Grand Tour. Disks Hard disk drive USB diskette drive DVD-ROM drive Available in four sizes. • 7.94 GB (30.0 billion bytes) • 37.26 GB (40.0 billion bytes) • 55.88 GB (60.0 billion bytes) • 74.53 GB (80.
Features DVD-R/-RW drive CD-ROM XA Mode 2 (Form1, Form2) Enhanced CD (CD-EXTRA) CD-G (Audio CD only) Addressing Method 2 Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CDRW at up to 10 speed, DVD-R and DVD-RW at single speed.
INTRODUCTION User's Manual DVD±RW drive (DVD Dual drive) Some models are equipped with a full- size DVD±RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CDR at up to 16 speed, CD-RW at up to 10 speed, DVD-R and DVD-RW at maximum 2 speed. DVD+R and DVD+RW at maximum 2.4 speed.
Features Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).Note that some models are not equipped with this port. External monitor 15-pin, analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB2.0) The computer has four Universal Serial Bus ports that comply with the USB 2.
INTRODUCTION User's Manual Communications Modem LAN 1-8 An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada and Australia. Only V.90 is available in other regions.
Special features Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Software Operating System Windows XP Home Edition/Professional Edition operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk. Refer to the Software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
INTRODUCTION User's Manual System automatic Standby/Hibernation This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernation item of the Basic Setup tab in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.
Utilities Turns on fan first, then if necessary lowers CPU processing speed. Performance Uses a combination of fan and lowering the CPU processing speed. Battery optimized Lowers the CPU processing speed first, then if necessary turns on the fan. Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk, when you turn on the power again, you can continue working right where you left off.
INTRODUCTION User's Manual DVD Video Player The DVD Video Player is used to play DVD-Video. It has an on-screen interface and functions. Click Start, point to All Programs, point to InterVideo WinDVD 4, then click InterVideo WinDVD 4. ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks.
Options TOSHIBA PC Diagnostic Tool displays the basic information on PC, and the test of built-in devices can also be performed.You can boot TOSHIBA PC Diagnostic Tool form the menu bar as follows. [Start]-[All Programs]-[TOSHIBA]-[Utilities]-[PC Diagnostic Tool] Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion 256 or 512 MB memory module (PC2700, DDR) can easily be installed in the computer.
INTRODUCTION User's Manual 1-14
Chapter 2 The Grand Tour THE GRAND TOUR Front with the display closed ........................................................... 2-1 Left side .............................................................................................. 2-2 Right side ........................................................................................... 2-3 Back side ............................................................................................ 2-5 Underside ...........................................
THE GRAND TOUR
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. DISPLAY LATCH SYSTEM INDICATORS Figure 2-1 Front of the computer with display closed Display latch System indicators This latch secures the LCD panel in its closed position. Slide the latch to open the display. LEDs let you monitor the status of various computer functions. Details are given in the Indicators section.
User's Manual Left side Figure 2-2 shows the computer’s left side. LINK INDICATOR (GREEN) I.LINK(IEEE1394) PORT LAN ACTIVE THE GRAND TOUR INDICATOR (ORANGE) SD CARD SLOT USB PORTS LAN JACK PC CARD SLOT SD CARD INDICATOR * Some models are not equipped with a SD card slot or a i.LINK (IEEE1394) port. Figure 2-2 The left side of the computer LAN active indicator (orange) This indicator glows orange when data is being exchanged between the computer and the LAN.
Right side NOTE: Operation of all functions of all USB devices has not been confirmed. Some functions might not execute properly. i.LINK (IEEE1394) Connect an external device, such as a digital video camera port to this port for high-speed data transfer. You must connect the AC adaptor when you use i.LINK. CB A PC card slot can accommodate one 5 mm Type II card. You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card.
User's Manual THE GRAND TOUR Fixed Optical media drive The computer is configured with a full-size optical media drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") disks without using an adaptor. Refer to the Fixed Optical media drive section in this chapter for technical specifications on each drive and to Chapter 4, Operating Basics, for information on using the drive and caring for disks.
Back side A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio input. When you connect an external microphone, the internal microphone is automatically disabled. Headphone jack A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speakers are automatically disabled.
User's Manual Universal Serial Bus (USB 2.0) ports THE GRAND TOUR Security lock Two Universal Serial Bus ports are on the back side. The port comply with the USB 2.0 standard, which enables data transfer speed 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) Also two ports are on the left side. A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. CAUTIONS: 1.
Underside Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. MEMORY MODULE COVER FAN VENT THE GRAND TOUR BATTERY PACK BATTERY SAFETY LOCK BATTERY RELEASE LATCH Figure 2-5 The underside of the computer Battery release latch Slide this latch to release the battery pack for removal. For detailed information on removing the battery packs, refer to Chapter 6, Power and Power-Up Modes.
User's Manual THE GRAND TOUR Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle.
System indicators Audio/Video control buttons* Previous button: Plays the previous track/chapter/ data. Play/pause button: Begins or pauses play. Stop button: Halts play. Next button: Plays the next track/chapter/data. Refer to Chapter 4, Operating Basics. * Audio/Video control buttons are provided with some models. Power button Touch Pad Press the power button to turn the computer’s power on and off.
User's Manual Battery THE GRAND TOUR Built-in HDD The Battery indicator shows the condition of the battery’s charge: Green indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge. Refer to Chapter 6, Power and PowerUp Modes. The Built-in HDD indicator glows green when the computer is accessing the hard disk. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator.
USB diskette drive When the CapsLock indicator glows the keyboard is in all-caps mode. CAPSLOCK INDICATOR Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. DISK-IN-USE INDICATOR DISKETTE SLOT Disk-In-Use Indicator Diskette slot EJECT BUTTON Figure 2-10 USB diskette drive This indicator lights when the diskette is being accessed.
User's Manual Eject button When a diskette is fully seated in the drive, the eject button pops out. To remove a diskette, push in the eject button and the diskette pops out partially for removal. THE GRAND TOUR CAUTION: Check the Disk-In-Use indicator when you use the diskette drive. Do not press the eject button or turn off the computer while the light is glowing. Doing so could destroy data and damage the diskette or the drive. NOTES: 1.
Fixed optical media drive Writable discs This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use Drag'n Drop CD+DVD to write compact discs. Refer to Chapter 4, Operating Basics. CDs ❑ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the ultra-speed CD-RW discs (Ultra-speed is CD-RW/DVD-ROM drive only) is maximum 24-speed.
User's Manual DVD-ROM drive THE GRAND TOUR The full- size DVD-ROM drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. NOTE: The read speed is slower at the center of a disc and faster at the outer edge. DVD read CD read 8 speed (maximum) 24 speed (maximum) CD-RW/DVD-ROM drive The full-size CD-RW/DVD-ROM drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.
Fixed optical media drive DVD Multi drive The full-size DVD Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. NOTE: The read speed is slower at the center of a disc and faster at the outer edge.
User's Manual AC adaptor THE GRAND TOUR The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6, Power and Power-Up Modes for details.
Chapter 3 Getting Started GETTING STARTED Setting up your work space .............................................................. 3-1 General conditions .............................................................................. 3-2 Placement of the computer ................................................................. 3-2 Seating and posture ........................................................................... 3-3 Lighting ..................................................................
GETTING STARTED
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User's Manual ❑ Seating and posture ❑ Lighting ❑ Work habits General conditions GETTING STARTED In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Setting up your work space ❑ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility. ❑ If you use a paper holder, set it at about the same height and distance as the computer. Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1.
User's Manual ❑ Adjust the back of your chair so it supports the lower curve of your spine. ❑ Sit straight so that your knees, hips and elbows form approximately 90 degree angles when you work. Do not slump forward or lean back too far. Lighting GETTING STARTED Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
Connecting the AC adaptor A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome. For more information on these topics or for pointers on exercises for such stress points as hands and wrists, please check with your library or book vendor. Also refer to the computer’s Instruction Manual for Safety & Comfort. Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power.
User's Manual 1. Connect the power cord to the AC adaptor. Figure 3-2 Connecting the power cord to the AC adaptor GETTING STARTED 2. Connect the AC adaptor’s DC output plug to the DC IN 15V input port on the back of the computer. DC IN 15V Figure 3-3 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN 15V indicators on the front of the computer should glow.
Turning on the power 2. Lift the display panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. NOTE: When you open the display, hold it with both hands and lift up slowly. DISPLAY LATCH GETTING STARTED Figure 3-4 Opening the display panel Turning on the power This section describes how to turn on the power.
User's Manual 3. Press and hold the computer’s power button for two or three seconds. POWER BUTTON GETTING STARTED Figure 3-5 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully.
Turning off the power 3. Click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off. 4. Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored.
User's Manual Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4. See Chapter 5, The Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click Start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. Hibernate is not displayed. 4. Press the Shift key. The Standby item will change to Hibernate. 5. Select Hibernate.
Turning off the power Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-IN HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode NOTES: 1.
User's Manual 4. If you carry the computer on board an aircraft or into a hospital, be sure to shut down the computer in hibernation mode or in shutdown mode to avoid radio signal interference. Benefits of standby GETTING STARTED The standby feature provides the following benefits: ❑ Restores the previous working environment more rapidly than does hibernation.
Restarting the computer NOTES: 1. When the computer is shut down in standby mode, the power indicator flashes orange. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power. Standby limitations Standby will not function under the following conditions: ❑ Power is turned back on immediately after shutting down. ❑ Memory circuits are exposed to static electricity or electrical noise.
User's Manual Restoring the preinstalled software from the Product Recovery DVD-ROM If preinstalled files are damaged, use the Product Recovery DVD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below. CAUTION: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. GETTING STARTED 1. Load the Product Recovery DVD-ROM in the fixed optical media drive and turn off the computer’s power. 2.
Chapter 4 Operating Basics OPERATING BASICS Using the Touch Pad ......................................................................... 4-1 Using the USB diskette drive ............................................................ 4-2 Connecting 3 1/2" diskette drive ......................................................... 4-2 Disconnecting 3 1/2" diskette drive ..................................................... 4-3 Using optical media drives .........................................................
OPERATING BASICS Connecting ....................................................................................... 4-21 Disconnecting ................................................................................... 4-22 Wireless LAN .................................................................................... 4-22 Security ............................................................................................ 4-23 Wireless communication switch ...............................................
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the external diskette drive, optical media drives, Audio/video controls, Sound System, the internal modem, the wireless communication and LAN. It also provides tips on caring for your computer and on heat dispersal. Using the Touch Pad To use the Touch Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
User's Manual Drag and drop 1. Hold down the left control button and move the cursor to drag the item you want to move. 2. Lift your finger to drop the item where you want it. Scroll Vertical: Move your finger up or down the right edge of the Touch Pad. Horizontal: Move your finger left or right along the bottom edge of the Touch Pad. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44megabyte or 720-kilobyte diskettes.
Using optical media drives Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Click the Safety Remove Hardware icon on the Task Bar. 3. Click Diskette drive. 4.
User's Manual Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the eject button to open the drawer slightly. EJECT BUTTON Figure 4-3 Pressing the eject button OPERATING BASICS b. Pressing the eject button will not open the drawer when the drive’s power is off.
Using optical media drives 2. Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. OPERATING BASICS Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6.
User's Manual CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Do not keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the drawer to close it. Press gently until it locks into place.
Audio/Video controls CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and cause injury. 2. The CD/DVD extends slightly over the sides of the drawer so you can grasp it. Hold the CD/DVD gently and lift it out. 3. Push the center of the drawer to close it.
User's Manual Play/Pause and Stop buttons A single button on a rocker controls the Play/Pause and Stop functions. Press on the icon to select the desired function. Play/Pause Press the Stop Press the icon to begin or pause play. icon to stop play. Controls for CD/DVD and Digital Audio CD/DVD control Os is running and you press Play/Pause. If an audio CD is in the opticalmedia drive,TOSHIBA Media Player starts and CD audio play begins.
Writing CDs on CD-RW/DVD-ROM drive Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above.
User's Manual Writing CD/DVDs on DVD±RW drive (DVD Dual drive) You can use the DVD±RW drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc.
Writing CD/DVDs on DVD-R/-RW drive Writing CD/DVDs on DVD-R/-RW drive You can use the DVD-R/-RW drive to write data to either CD-R/RW or DVD-R/-RW discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc.
User's Manual Writing CD/DVDs on DVD Multi drive You can use the DVD Multi drive to write data to either CD-R/RW or DVD-R/-RW/RAM discs. The following applications for writing are supplied on CD-ROM: Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc. Important message Before you write or rewrite to CD-R/RW or DVD-R/-RW/-RAM disc, read and follow all set-up and operating instructions in this section.
Writing CD/DVDs on DVD Multi drive CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYOYUDEN CO., LTD. PIONEER VIDEO CORPORATION MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Re-recordable Disc for Version 1.0 or Version 1.
OPERATING BASICS User's Manual ❑ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW discs. ❑ You cannot overwrite data that has been previously written to a DVD-RW disc. ❑ You cannot partially delete any data written to a DVD-RW disc. ❑ Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. ❑ Data deleted (erased) from a CD-RW and DVD-RW/-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it.
Writing CD/DVDs on DVD Multi drive ❑ Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. Drag’n Drop CD+DVD Note the following limitations when you use Drag’n Drop CD+DVD: DVD-Video cannot be created using Drag’n Drop CD+DVD. ❑ DVD-Audio cannot be created using Drag’n Drop CD+DVD. ❑ You cannot use Drag’n Drop CD+DVD’s music CD function to record music to a DVD±RW disc.
User's Manual Data verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Right-click Data BOX and select Options to display the DATA DISC Option window. 2. Mark the Record and Verify check box and select Byte compare. 3. Click the OK button. The “Record and Verify” function automatically checks whether data has been correctly recorded onto a CD/DVD.
Sound System Diskettes 1. Store your diskettes in the container they came in to protect them and keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2. Do not slide back the diskette’s protective metal covering or touch the diskette’s magnetic surface. Fingerprints may prevent the diskette drive from reading data from the diskette. 3. Data may be lost if the diskette is twisted; bent; or exposed to direct sunlight, extreme heat or cold. 4.
User's Manual 1. Click Start, point to All Programs, point to Accessories, point to Entertain ment and click Volume Control. 2. Click Properties, check the Microphone checkbox and click OK. 3. Click Options and select Advanced Controls. 4. Click Advanced. 5. Check the MIC Boost checkbox and click Close. SoundMAX Control Panel The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management.
Modem If you want to a more effect for the power management, you can select another mode, the High Power Savings which can save the power than the Normal Power Savings. To select it, follow the steps below. 1. Clicked the Power Management tab. 2. Select the High Power Savings in the Power Mode pull-down list. 3. Input a time in Power Save Delay (Seconds). NOTE: If the High Power Saving is selected, you need to play an audio file once before you use a microphone or play an audio CD by the analog CD audio.
User's Manual 2. The Region Selection icon will appear in the Windows Task Bar. Figure 4-9 The Region Selection icon 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4. Select a region from the region menu or a telephony location from the submenu.
Modem Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.
User's Manual CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Figure 4-11 Connecting the internal modem OPERATING BASICS CAUTION: Do not pull on the cable or move the computer while the cable is connected.
Wireless LAN ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A and G, Revision B/G, A/B/G combo type) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1Mbit/s. (Revision B) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 108, 96.72, 48, 36, 24, 18 and 12Mbit/s. (Turbo Mode, Revision A/B/G combo type) ❑ Frequency Channel Selection (Revision A/Turbo Mode:5GHz, Revision B/G: 2.
User's Manual Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application.
LAN Connecting LAN cable To connect the LAN cable, follow the steps below. CAUTIONS: 1. Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. 2. Do not connect any other cable to the LAN's jack except the LAN cable. Otherwise, malfunctions or damage may occur. 3. Do not connect any power supplying device to the LAN cable that is connected to the LAN's jack.
User's Manual Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Heat dispersal ❑ If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely closed. ❑ Turn off the power to the computer. ❑ Disconnect the AC adaptor and all peripherals before moving the computer. ❑ Close the display. Do not pick up the computer by its display panel. ❑ Close all port covers. ❑ Use the carrying case when transporting the computer. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor.
OPERATING BASICS User's Manual 4-28
Chapter 5 The Keyboard Typewriter keys ................................................................................. 5-1 F1 … F12 function keys ..................................................................... 5-2 Soft keys: Fn key combinations ........................................................ 5-2 Emulating keys on enhanced keyboard .............................................. 5-2 Hotkeys ..............................................................................................
THE KEYBOARD
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard of a portable computer is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad.
Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future.
User's Manual LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in Power Saver. NOTE: Display clarity increases with the brightness level.
Windows special keys Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the start menu and the other has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay THE KEYBOARD Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
Generating ASCII characters Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
THE KEYBOARD User's Manual 5-10
Power and Power-Up Modes Power conditions ................................................................................ 6-1 Power indicators ................................................................................ 6-2 Battery indicators .............................................................................. 6-2 DC IN 15V indicator .......................................................................... 6-3 Power indicator ..................................................................
POWER AND POWER-UP MODES
Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions continued Power on AC Battery • Operates adaptor charge is • LED: Battery off not above low connected battery Power off (no operation) DC IN 15V off trigger point Battery • Operates charge is • LED: Battery below low flashes orange battery DC IN 15V off trigger point Battery Computer goes charge is into resume mode exhausted shuts down No • Cannot operate battery • LED: Battery off installed DC IN 15V off Powe
Battery types DC IN 15V indicator Check the DC IN 15V indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light.
POWER AND POWER-UP MODES User's Manual Battery pack When the AC adaptor is not connected, the computer’s main power source is a removable lithium-ion battery pack, also referred to in this manual as the battery pack. You can purchase additional battery packs for extended use of the computer away from an AC power source. Before you remove the battery pack, set the computer to Hibernation mode or save your data and shut down the computer. Do not change the battery pack while the AC adaptor is connected.
Care and use of the battery pack CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. NOTE: You can change the setting of RTC by pressing F1 key. Refer to Chapter 9, Troubleshooting for the detail.
POWER AND POWER-UP MODES User's Manual 2. Never try to disassemble, repair or otherwise tamper with a battery pack. The battery pack will overheat and ignite. Leakage of caustic alkaline solution or other electrolytic substances will cause fire or injury, possibly resulting in death or serious injury. 3. Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury.
Care and use of the battery pack 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 4. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1.
POWER AND POWER-UP MODES User's Manual 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the battery pack while the computer is in Suspend or Standby mode. Data will be lost. Note 1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2.
Care and use of the battery pack POWER AND POWER-UP MODES Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack 8400mAh 7 to 20 or longer about 3.5 RTC battery 8 Doesn’t charge NOTES: 1. The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
POWER AND POWER-UP MODES User's Manual 3. Charge the battery until the Battery indicator glows green. Repeat these steps two or three times until the battery recovers normal capacity. NOTE: Leaving the AC adaptor connected will shorten battery life. At least once a month, run the computer on battery power until the battery is fully discharged, then recharge the battery. Monitoring battery capacity Remaining battery power can be monitored in Power Saver. NOTES: 1.
Care and use of the battery pack POWER AND POWER-UP MODES • Monitor Power off • HDD Power off ❑ How often and how long you use the hard disk and the diskette drive. ❑ How much charge the battery contained to begin with. ❑ How you use optional devices, such as a PC card, to which the battery supplies power. ❑ Enabling Standby mode conserves battery power if you are frequently turning the computer off and on. ❑ Where you store your programs and data.
POWER AND POWER-UP MODES User's Manual 4. Connect the AC adaptor to the computer and the power cord to a power outlet. The DC IN 15V indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged. If the DC IN 15V indicator does not glow, power is not being supplied. Check the connections for the AC adaptor and power cord. 5. Charge the battery pack until the Battery indicator glows green. ❑ If you have extra battery packs, rotate their use.
Replacing the battery pack 4. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Turn the computer upside down. 5.
POWER AND POWER-UP MODES User's Manual Installing the battery pack To install a battery, follow the steps below. CAUTIONS: 1. The battery pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 2. Do not touch the latch while holding the computer.
Starting the computer by password To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter. NOTE: If you enter the password incorrectly three times in a row, the computer shuts off.
POWER AND POWER-UP MODES User's Manual Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. NOTE: If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed. System Auto Off This feature turns the system off automatically if it is not used for a set duration.
Chapter 7 HW Setup and Passwords HW SETUP AND PASSWORDS HW Setup ........................................................................................... 7-1 Accessing HW Setup ......................................................................... 7-1 HW Setup window .............................................................................. 7-1 Supervisor password .......................................................................
HW SETUP AND PASSWORDS
Chapter 7 HW Setup and Passwords HW Setup TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Some models are not equipped with Parallel/Printer tab and/or CPU tab.
User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. HW SETUP AND PASSWORDS About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered Change or remove the password. (Default) Set the password.
HW Setup If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: HW SETUP AND PASSWORDS 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** NOTE: If you click the OK button before entering the password, Registered will appear on the display. 3. Click the OK button.
User's Manual NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost. To create a Key FD follow the steps below. 1. Turn off the computer’s power. HW SETUP AND PASSWORDS 2. Connect the diskette drive to a USB port on the computer. 3. Set a diskette’s write-protect tab to the write enable position and insert the diskette in the drive. NOTE: All data on the diskette will be destroyed. 4. Turn on the computer’s power. Password= will be displayed on the LCD. 5.
HW Setup Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. ECP Standard Bi-directional Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) This setting should be used with some other parallel devices. This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
User's Manual HT Technology This tab is available only on the models with the CPU that supports HyperThreading Technology (HTT). You can enable or disable the HTT feature (including control for PM when enabling it) using this tab. HW SETUP AND PASSWORDS Enabled with PM* Enabled Select this option to enable the HTT feature with PM activated. without PM* Select this option to enable the HTT feature with PM deactivated. Disabled Select this option to disable the HTT feature.
HW Setup CD-ROM −> LAN −> FDD −> HDD The computer looks for bootable files in the following order: CD-ROM, LAN, diskette drive and HDD. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: Selects the USB diskette drive. N Selects the Network. 1 Selects the primary HDD. P Selects the PC card HDD. C Selects the CD-ROM*. HW SETUP AND PASSWORDS U * In this computer, CD-ROM refers to the Fixed optical media drive.
User's Manual 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. HW SETUP AND PASSWORDS 2. The selection method above does not change the boot priority settings in HW Setup. 3. If you press a key other than one of those above or if the selected device is not installed, the system will boot according to the current setting in HW Setup. 4.
HW Setup NOTE: The Wake-up on LAN function consumes power even when the system is off. Leave the universal AC adaptor connected while using this feature. Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Disabled Enables the Wake-up on Keyboard. Disables the Wake-up on Keyboard.
User's Manual Supervisor password HW SETUP AND PASSWORDS Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file.
Chapter 8 Optional Devices OPTIONAL DEVICES PC cards ............................................................................................. 8-2 Inserting a PC card ............................................................................. 8-2 Removing a PC card ........................................................................... 8-3 SD cards ............................................................................................. 8-4 Formatting an SD card ............................
OPTIONAL DEVICES
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC cards ❑ SD cards ❑ Memory expansion OPTIONAL DEVICES ❑ Power devices ❑ Battery pack ❑ Universal AC adaptor Peripheral devices ❑ USB diskette drive ❑ External monitor ❑ Parallel printer ❑ i.
User's Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. After installing the card, refer to the card’s documentation and check the configuration in Windows to make sure it is appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.
User's Manual SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate Multi Media cards. OPTIONAL DEVICES CAUTION: Keep foreign objects out of the SD card slot.
SD cards 2. Press gently to ensure a firm connection. SD CARD CAUTION: Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the system tray and disable the SD card. 2. Push in the card and release it to pop the card out slightly. 3. Grasp the card and remove it.
User's Manual CAUTIONS: 1. Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. 2. Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost.
Memory expansion CAUTIONS: 1. Refer to General Precautions for the attention when keyboard brace is removed. 2. Use only memory modules approved by TOSHIBA. 3. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. NOTES: 1. The computer is turned on. b. The computer was shut down using the Stand by mode or Hibernation mode.
User's Manual 5. Insert a thin object under the rim of the keyboard brace and lift out the brace. Figure 8-5 Removing the keybord brace OPTIONAL DEVICES 6. Remove two screws securing the keyboard and one screw securing the metal brace. Lift off the metal brace. NOTE: Use a point size 0 Phillips screwdriver. 7. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. CAUTIONS: 1. When you move the keyboard forward, do not touch the keys.
Memory expansion 8. Lift into the left the insulation sheet covering the memory module and secure the sheet with tape to keep it out of your way. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. NOTE: The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A. SLOT B SLOT A OPTIONAL DEVICES Figure 8-7 Lifting into the left the insulation sheet. 9.
User's Manual 10. Seat the insulation sheet to cover the module. NOTE: Be sure to check that the insulation sheet is returned to the original position to cover the memory module. 11. Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard. CAUTION: When seating the keyboard, be sure to fit the flexible printed circuit board under the palm rest if the flat cable was pulled out while you were removing the keyboard. OPTIONAL DEVICES 12.
Battery pack CAUTIONS: 1. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. 2. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. LATCHES OPTIONAL DEVICES Figure 8-9 Removing the memory module 7.
User's Manual USB diskette drive The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. OPTIONAL DEVICES 2.
i.LINK (IEEE1394) 4. Insert the other end of the cable into the printer’s parallel connector. 5. Fasten the connector to the printer with the clips on the parallel port. 6. Turn on the printer. 7. Turn on the computer. 8. Start the HW Setup program. Refer to Chapter 7, HW Setup and Passwords. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect. 12. Select the printer in Windows Add Print Wizard.
User's Manual ❑ You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment. ❑ If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. ❑ Make sure data transfer has ended or turn off the computer, before you: • Connect/disconnect an i.LINK device to/from the computer. • Connect/disconnect an i.LINK device to/from another i.
Security lock Disconnecting 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. NOTE: Refer also to the documentation that came with your i.LINK device. Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. CAUTION: The Security Lock Slot is between Cooling Vent.
OPTIONAL DEVICES User's Manual 8-16
Chapter 9 Troubleshooting TROUBLESHOOTING Problem solving process ................................................................... 9-1 Preliminary checklist .......................................................................... 9-1 Analyzing the problem ........................................................................ 9-2 Hardware and system checklist ........................................................ 9-3 System start-up ................................................................
TROUBLESHOOTING
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down and DC IN 15V indicator blinks orange Leave the computer off until the DC IN 15V indicator stops blinking. NOTE: It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN 15V indicator stops blinking.
User's Manual Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer. Battery TROUBLESHOOTING If you suspect a problem with the battery, check the DC IN 15V indicator as well as the Battery indicator. For information on indicator and battery operation see Chapter 6, Power and Power-Up Modes.
Hardware and system checklist Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer. If the indicator still does not glow, the battery may be at the end of its operating life. Replace it. If you do not think the battery is at the end of its operating life, see your dealer.
User's Manual Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software’s documentation. If you are still unable to use the keyboard, consult your dealer.
Hardware and system checklist PRESS FROM THE UPSIDE PROJECTING PART SPRING PROJECTING PART • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top.
User's Manual 2. Attach the plastic spring to the keyboard with its flat face downward after confirming the direction. FLAT FACE DOWNWARD TROUBLESHOOTING 3. Press from the upside until you hear a click after replacing the key-top to the right position. LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords for more information.
Hardware and system checklist Problems above remain unresolved or other problems occur Refer to your software’s documentation to determine if the software is causing the difficulty. Contact your dealer if the problems continue. Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive or a CD-ROM is in the optical media drive. Remove any diskette and/or CD-ROM and check Boot priority.
User's Manual DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. TROUBLESHOOTING A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Hardware and system checklist Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place.
User's Manual CD-ROM: CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), CD-G (Audio CD only), Addressing Method 2 Recordable: CD-R, CD-RW CD Check the region code on the DVD. It must match that on the CD-RW/DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour.
Hardware and system checklist Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning.
User's Manual • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software during writing. • Do not jar the computer during writing. • Do not connect/ disconnect external devices or install/remove internal cards during writing. If problems persist, contact your dealer. DVD Multi drive For more information, refer to Chapter 4, Operating Basics.
Hardware and system checklist Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
User's Manual DVD±RW drive (DVD Dual drive) For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive's drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. TROUBLESHOOTING A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction.
Hardware and system checklist Check the region code on the DVD. It must match that on the DVD±RW drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software during writing.
User's Manual PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. SD card TROUBLESHOOTING Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected.
Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to standby its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
User's Manual Touch pad is sensitive 1. Open the Control Panel. or blunt. 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6. The Properties for Synaptics Touchpad on PS/2 port screen appears. Double-click Sensitivity in the Select an item section on the left side of the screen. 7. PalmCheck and Touch Sensitivity are dis played. Click Touch Sensitivity. 8.
Hardware and system checklist 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3. Set the speed as instructed and click OK. The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentations for instructions on cleaning.
User's Manual Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. (If slot A, two beeps. If slot B, three beeps. If both, two and three beeps. ) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Turn off the Power. 2. Disconnect the AC adaptor and all more, peripheral devices. 3. Remove the battery. 4.
Hardware and system checklist Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys Fn + F5 to change the display priority and make sure it is not set for the internal display.
User's Manual You can also use the ATX command. Refer to Appendix C, AT Commands. You place a call, but a connection can’t be made Make sure the settings are correct in your communications application. After making a call you can’t hear a ring Make sure the tone or pulse selection in your communications application is set correctly. TROUBLESHOOTING You can also use the ATD command. Refer to Appendix C, AT Commands.
Hardware and system checklist Standby/Hibernation Problem Procedure The system will not enter Standby/Hibernation Is Windows Media™ Player open? The system might not enter Standby/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/Hibernation. If problems persist, contact your dealer. LAN Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
User's Manual i.LINK (IEEE1394) Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add New Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Hardware and system checklist Printer Refer also to the Parallel printer sections in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn on. Check that the printer is connected to an electric outlet. Make sure the outlet is supplying power by plugging in an appliance. Computer/printer do not communicate Make sure the printer is turned on and is online (ready to use).
User's Manual TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ❑ Review troubleshooting sections in the documentation for software and peripheral devices.
TOSHIBA support Outside of Europe United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA TROUBLESHOOTING Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R8H2 China TOSHIBA Computer Systems (Shanghai) Co., Ltd. Bldg. 33, No. 351, Jinzang Road, Pudong New Area, Shanghai, P.R.
TROUBLESHOOTING User's Manual 9-32
Appendix A Specifications ............................................................................... A-1 Appendix B Display Controller and Modes ..................................................... B-1 Appendix C AT Commands ............................................................................. C-1 Appendix D S-registers .................................................................................... D-1 Appendix E V.90 .......................................................................
APPENDIXES
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size Weight 337 (w) x 298 (d) x40/46 (h) millimeters (not including parts that extend beyond the main body) 3.5 kilograms, configured with: 15"XGA-TFT, CD-RW/ DVD-ROM drive, Modem, LAN, IEEE1394, Wireless LAN Weight will vary with other configurations.
APPENDIX A User's Manual Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) Communication speed Transmitting level V.17/V.29/V.27ter /V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors. The 15.0" TFT LCD panel displays up to 1024 horizontal and 768 vertical pixels and 1400 horizontal and 1050 vertical pixels.
User's Manual Video modes APPENDIX B The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Appendix B Table1 Video modes (VGA) continued Type Resolution Character LCD matrix colors (pels) CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 16 of 256K 70 11 VGA Grph VGA Grph 640 × 480 Pels 640 × 480 Pels 8 × 16 2 of 256K 2 of 256K 60 8 × 16 16 of 256K 16 of 256K 60
User's Manual APPENDIX B Table 2 Video modes (XGA) Resolution LCD colors CRT colors 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K (Virtual) 256/256K 60 75 85 100 1400 × 1050 256/256K (Virtual) 256/256K 60 75 85 1600 × 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 × 1440 256/256K (Virtual) 256/256K 60 75 85 2048 × 1536 256/256K (Virtual) 256/256K 60 75 B-4 Vertical fre
Appendix B Table 2 Video modes (XGA) continued LCD colors CRT colors Vertical frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1400 × 1050 64K/64K (Virtual) 64K/64K 60 75 85 1600 × 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 × 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048× 1536 64K/64K (Virtual) 64K/64K 60 75 CAUTION: Some SVGA modes ar
User's Manual APPENDIX B Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1400 × 1050 16M/16M (Virtual) 16M/16M 60 75 85 1600 × 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 × 1440 16M/16M (Virtual) 16M/16M 60 75 85 2048 × 1536 16M/16M (Virtual) 16M/16M 60 75 B-6 Vertical frequency
Appendix B Table 3 Video modes (Super XGA+) LCD colors CRT colors Vertical frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1400 × 1050 256/256K 256/256K 60 75 85 1600 × 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 × 1440 256/256K (Virtual) 256/256K 60 75 85 2048 × 1536 256/256K (Virtual) 256/256K 60 75 CAUTION: Some SVGA modes are not
User's Manual APPENDIX B Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1400 × 1050 64K/64K 64K/64K 60 75 85 1600 × 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 × 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 × 1536 64K/64K (Virtual) 64K/64K 60 75 B-8 Vertical frequency (Hz) CAUTIO
Appendix B Table 3 Video modes (Super XGA+) continued LCD colors CRT colors Vertical frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 60 75 85 100 1400 × 1050 16M/16M 16M/16M 60 75 85 1600 × 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 × 1440 16M/16M (Virtual) 16M/16M 60 75 85 2048 × 1536 16M/16M (Virtual) 16M/16M 60 75 CAUTION: Some SVGA modes are not suppor
User's Manual Display Settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display at the same time. ❑ The [Settings] tab is displayed in the following steps; APPENDIX B a. Open [Control Panel], click [Appearance and Themes] b. Click [display] c.
Appendix B ❑ The way to move to multi-monitor a. Press [Ctrl] + [Alt] + [F12] keys to make [Intel(R) 82852/82855 GM/GME Graphics Controller Prope...] displayed. (See FigureB-2) b. Click in the left of [Devices] tab (See FigureB-2), then select [Extended Desktop]. FigureB-2 Intel(R) 82852/82855 GM/GME Graphics Controller Prope... B-11 APPENDIX B c. Check that the Primary Device is fixed into Note Book (the display of the computer) and the Secondary Device is being fixed into Monitor (CRT display).
User's Manual 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same. Reduce the resolution, use the display of the computer only, use the CRT display only or set display device in the multi-monitor, then play DVD. APPENDIX B Please refer to External monitor in the online manual of Chapter8 Optional Devices or the application guide for the setting of each display device. 3.
Appendix B c. The following [Set up] screen is displayed, then remove the check of [Use Hardware Decode Acceleration] (The check of [Use Hardware Color Acceleration] is removed automatically). APPENDIX B Figure B-5 Setup d. Click [OK] button(The [Set up] tab closes automatically). 4. The DVD video overlay is not displayed when the display mode of CRT display is set to high resolution and hifh refresh rate mode at LCD/CRT simultinous or multi-monitor.
User's Manual 5. A DVD-reproduced image may not be displayed in correct position when you press Fn+F1 to enter into Instant Security mode while a DVD is playing under WinDVD 4.0, and then move the mouse or press the key to exit Instant Security mode. In this case, close WinDVD 4.0 and open it again, or pres the Stop button and then the Play button to display the DVD image in correct position. The following steps will work around this problem. APPENDIX B a. Run WinDVD 4.0.
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn Any command issued is acknowledged with a response in either text or numeric values known as result codes.
User's Manual A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
Appendix C En ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. E0 Disables echo to the computer.
User's Manual Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode APPENDIX C This command turns the speaker on or off. M0 The speaker is off. M1 The speaker is on until the modem detects the carrier signal (default). M2 The speaker is always on when modem is off-hook.
Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Result Codes: OK n=0,1,3 P Select pulse dialing This command configures the modem for pulse (non touch-tone) dialing.
User's Manual T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
Appendix C X5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT , RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. APPENDIX C Busy tone detect Disabled: The modem ignores any busy tones it receives.
User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise &Dn DTR control APPENDIX C This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard tone to 550 Hz. &G2 Sets guard tone to 1800 Hz. Result Codes: OK n=0,1,2 ERROR Otherwise &Kn Local flow control selection Disable flow control.
User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result Codes: APPENDIX C &V OK n=0 CONNECT n=1 ERROR Otherwise Display Current Configuration This command displays the current configuration of the modem.
Appendix C \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode. \N3 V.42, MNP, or buffered (default). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode.
User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: OK n=0,1 ERROR Otherwise %B View numbers in blacklist APPENDIX C If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: S1 rings Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: S5 ASCII Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only.
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.
Appendix D S37 Dial line rate maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps APPENDIX D S37 = 0 (default) D-5
User's Manual AT command set result codes The following table shows the result codes.
Appendix D Result Code Numeric Description DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLIST FULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
APPENDIX D User's Manual D-8
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. NOTE: V.
User's Manual APPENDIX E Table E-1 Result codes for a V.90 connection No.
Appendix E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V42 NoEC V.42 error control and V.42bis data compression V.42 error control only No error control protocol AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX E User's Manual E-4
Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for information only. CAUTION: Refer to General Precations for the attention when keybord brace is removed. To install the internal modem follow the procedures below.
APPENDIX F User's Manual 9. Remove two screws, which you use later to secure the modem board. 10. Connect the modem board cable and seat the modem board. 11. Secure the modem board with two screws removed in step 9. 13. Seat the insulation sheet to cover the modem board. 14. Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard. 15. Two screws secure the keyboard and one screw secures the metal brace. 16.
APPENDIX F 14. Two screws secure the keyboard and one screw secures the metal brace. 15. Seat the keyboard brace and press to secure latches. 16. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. Refer to the installation procedures for details. The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
APPENDIX F User's Manual F-4
Appendix G Wireless LAN APPENDIX G Card Specifications Form Factor Mini PCI TypeIII Compatibility IEEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance.
User's Manual R-F Frequency Modulation Band 5GHz (5150-5850 MHz) (Revision A, Turbo Mode) Band2.4GHz (2400-2483.5 MHz) (Revision B, Revision B, B/G, A/B/G combo type) DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK APPENDIX G Technique (Revision B, Revision B/G, A/B/G combo type) OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, G and Turbo Mode, Revision B/G, A/B/G combo type) The range of the wireless signal is related to the Transmit Rate of the wireless communication.
Appendix G 9 10 11 12 13 *1 Factory-set default channels 2452 2457*1 2462 2467*2 2472*2 ❑ For Wireless LAN Cards installed in Wireless clients that operating in a peerto-peer mode, the card will use the default channel 10. ❑ In a Wireless LAN Access Point, the Wireless LAN card will use the factoryset default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device. Wireless IEEE 802.
User's Manual Wireless Channels Sets (Turbo Mode) APPENDIX G Frequency Range Channel ID 5150-5850 MHz Note 42 5210 US only *1 50 5250 US only *1 58 5290 US only *1 152 5760 US only *1 160 5800 US only *1 *1: Available Area: US (USA, CANADA) only G-4
Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, communication, mini PCI and indent devices.
User's Manual The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice. *Figures indicate the CPU operating speed in megahertz. For example, P2.6 means Mobile Intel® Pentium®4 processor 2.60GHz.
The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
GLOSSARY adaptor RAM: random access memory RGB: red, green, and blue (Abbreviations continued) ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics array plus TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics arr
cache memory async: Short for asynchronous. asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files.
GLOSSARY capacity memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. card: Synonym for board. See board. CardBus: An industry standard bus for 32-bit PC cards.
dialog box configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration. control keys: A key or sequence of keys you enter from the keyboard to initiate a particular function within a program. controller: Built-in hardware and software that controls the functions of a specific internal or peripheral device (e.g. keyboard controller).
GLOSSARY disk drive disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record. diskette: A removable disk that stores magnetically encoded data. Also called a floppy disk.
hardware execute: To interpret and execute an instruction. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support. F fast infrared: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file: A collection of related information; a file can contain data, programs, or both.
GLOSSARY hertz hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer. hotkey: The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume.
monitor K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses large scale integration. KB: See kilobyte. M keyboard: An input device containing switches that are activated by manually pressing marked keys.
GLOSSARY motherboard monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
prompt port: The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject.
GLOSSARY Radio frequency interference (RFI) shield R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
write protection U synchronous: Having a constant time interval between successive bits, characters or events. V system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk. Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
GLOSSARY Glossary-14
Index D AC adaptor 1-3, 2-16 DC IN 15V port 2-6 connecting 3-5 universal 1-13 ASCII characters 5-9 Auto power on, See Power DC IN 15V indicator 2-9, 6-3 Diskette care 4-17 Display 1-6, 2-8, See also Video modes and Monitor external automatic power off 1-9 controller 1-6, Appendix B hinge 2-8 opening 3-6 selection, See Hot keys Documentation list 1-2 Drag'n Drop CD+DVD 1-12, 4-15 DVD Multi drive 2-15 location 2-3 using 4-3 writing 4-12 DVD-ROM drive 2-14 location 2-3 using 4-3 DVD-R/-RW drive 2-14 location
User's Manual Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory expansion INDEX F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn-esse 1-11 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 (display brightness) 5-6 Fn + F8 (wireless setting) 5-6 Fn + F9 (touch pad) 5-6 Fn + F10 (arrow mode) 5-
Index jack location 2-2 using 4-24 LCD, See Display, Video modes and Monitor external Lock, security, See Security lock M N Numeric keypad, See Keypad overlay O Operating system, See Windows Overlay, See Keypad overlay P Panel power on/off, See Power Password power on 1-10 starting the computer by 6-15 supervisor 7-10 user 7-2 Index-3 INDEX Main battery, See Battery pack Memory 1-3 expansion 1-13, 8-6 installing 8-7 removing 8-10 slots 1-3 video RAM 1-3 Microphone, See sound system, microphone Microp
INDEX User's Manual password 9-7 PC card 9-20 pointing device 9-21 power 9-4 preliminary checklist 9-1 Real time clock 9-28 SD card 9-20 self test 9-4 sound system 9-24 standby/hibernation 9-27 support from TOSHIBA 9-30 system start-up 9-3 Touch Pad 9-21 USB 9-23 Wireless LAN 9-27 Processor 1-2 microphone 1-7, 2-5 speakers 2-8 Volume control 2-4 Standby 1-11 System automatic Standby/Hibernation 1-10 T TOSHIBA TOSHIBA Power Saver 1-11 TOSHIBA Touch and Launch 1-12 TOSHIBA Utilities 1-9 Touch Pad 1-7, 2-9
