TOSHIBA Satellite A300/ Satellite Pro A300/ Satellite A300D/ Satellite Pro A300D series User’s Manual
Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Bluetooth™ is a registered trademark owned by its proprietor and used by TOSHIBA under license. DVD MovieFactory is trademarks of the Ulead Systems. Inc. Labelflash™ is a trademark of YAMAHA CORPORATION. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No's.
Safety instructions Use the following safety guidelines to help to protect yourself and your computer. When using your computer Do not operate your portable computer for an extended period of time with the base resting directly on your body. With extended operation, heat can potentially build up in the base. Allowing sustained contact with the skin could cause discomfort or, eventually, a burn. ■ Do not attempt to service the computer yourself. Always follow installation instructions closely.
FCC information FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BSMI notice (Taiwan only) EU Declaration of Comformity Supplementary Information: The product complies with the requirements Of the Low Voltage Directive 2006/95/EC,the EMC Directive 2004/108/EC and/or the R&TTE Directive 1999/5/EC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Modem warning notice Conformity statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan’s Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes. The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Notes for users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ■ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Following information is only for EU-member States The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Optical disc drive standards TOSHIBA Satellite A300/Satellite Pro A300/Satellite A300D/Satellite Pro A300D series computer is shipped with one of the following drives preinstalled: DVD Super Multi (+-R DL), DVD Super Multi (+-R DL) /w Label Flash, HD DVD-ROM, or HD DVD-RW drive.
DVD Super Multi (+-R DL) drive Panasonic UJ-870B/UJ-870F Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED Panasonic Communications Co., Ltd. 1-62, 4-Chome Minoshima Hakata-ku Fukuoka, Japan HLDS GSA-T40N/GSA-T40F Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED Hitachi-LG Data Storage, Inc.
Pioneer DVR-KD08TBM/DVR-KD08TBF Location of the required label COMPLIES WITHFDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J MANUFACTURED PIONEER CORPORATION 4-1, MEGURO 1-CHOME, MEGUROKU TOKYO 153-8654, JAPAN Toshiba Samsung TS-L632H/TS-L632P Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J, APPLICABLE AT THE DATE OF MANUFACTURE.
HD DVD-ROM drive Toshiba SD-L802B Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR CHAPTER1, SUBCHAPTER J, APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED TOSHIBA CORPORATION 1-1-1, SHIBAURA, MINATO-KU, TOKYO 105-8001, JAPAN HD DVD-RW drive Toshiba SD-L912A Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR CHAPTER1, SUBCHAPTER J, APPLICABLE AT THE DATE OF MANUFACTURE.
International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface General Precautions Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Features. . . . . . . . . . . . .
Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optical disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About the HD DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Region codes for DVD drives and media . . . . . . . . . . . . . . . . . . . . Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DVD Super Multi (+-R DL) drive . . . . . . . . . .
Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Loading discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11 Removing discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Function button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Using TOSHIBA HD DVD PLAYER to enjoy HD DVDs . . . . . . . . . . . 4-16 HD DVD playback restrictions. . . . . .
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disconnecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the FM tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BluetoothTM wireless technology . . .
Retaining data with power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Extending battery life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Removing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11 Installing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 9 Troubleshooting Problem solving process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Preliminary checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Analyzing the problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 System start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Non-applicable icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copy protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LCD brightness and eye strain . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface Congratulations on your purchase of the TOSHIBA Satellite A300/Satellite Pro A300/Satellite A300D/Satellite Pro A300D series computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A300/Satellite Pro A300/Satellite A300D/Satellite Pro A300D series computer.
Preface Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Preface ABC When procedures require an action such as clicking an icon or entering text, the icon’s name or the text you are to type in is represented in the typeface you see to the left. Display ABC Names of windows or icons or text generated by the computer that appear on its display screen are presented in the typeface you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
General Precautions Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packaging materials for future use.
Introduction Software Microsoft® Windows Vista™ The following software is preinstalled: ■ Microsoft® Windows Vista™ ■ Modem Driver (Can be used only for Modem models) ■ Bluetooth Driver (Can be used only for Bluetooth models) ■ Display Drivers for Windows ■ Fingerprint utility (Can be used only for Fingerprint utility models) ■ LAN Driver ■ Pointing Device Driver ■ Presto! BizCard 5 (Is preinstalled with some models) ■ Sound Driver for Windows ■ Ulead DVD MovieFacotry® for TOSHIBA ■ Wireless LAN driver (Ca
Introduction Features This computer incorporates the following features and benefits: Processor Built-in Please visit your region’s website for the configuration details of the model that you have purchased. Memory Slots PC2-5300 512 MB, 1024 MB or 2048 MB memory modules can be installed in the two memory slots. Maximum system memory size and speed are depending on the model you purchased. PC2-5300 memory module works as PC2-4200 speed on Mobile Intel® GL960 Express Chipset model.
Introduction Video RAM Depending on the model you purchased. Mobile Intel® GM965 Express Chipset/Mobile Intel® GL960 Express Chipset model: Video RAM capacity shares with main memory, and the proportion depends on Dynamic Video Memory Technology. Mobile Intel® GM965 Express Chipset/Mobile Intel® PM965 Express Chipset model in graphic chip by ATI Mobility RadeonTM HD 3470: External 64/128/256 MB.
Introduction Disks Hard disk drive (HDD) User’s Manual The computer has one or two integrated, 2 1/2" hard disk drive(s) for nonvolatile storage of data and software(depending on the model you purchased). It comes in the following sizes. ■ 80 GB ■ 120 GB ■ 160 GB ■ 200 GB ■ 250 GB ■ 300 GB ■ 320 GB ■ 400 GB ■ 500 GB Disclaimer (Hard disk drive capacity) For more information on the Disclaimer regarding Hard disk drive capacity, please refer to the Disclaimers section in Chapter 10.
Introduction DVD Super Multi (+-R DL) drive Some models are equipped with a full-size DVD Super Multi (+- R DL) drive module that allows you to record data to rewritable CD/DVDs as well as run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CDROMs at maximum 24 speed.
Introduction HD DVD-ROM drive Some models are equipped with a full-size HD DVD-ROM drive module that allows you to run CD/DVD/HD DVDs without using an adaptor. The drive reads DVD-ROMs at a maximum 8x speed, CD-ROMs at a maximum 24x speed, and HD DVDs at a maximum 1x speed. It writes CD-Rs at up to 16x speed, CD-RWs at up to 10x speed, DVD-Rs and DVD+Rs at up to 4x speed, DVDRWs and DVD+RWs at up to 4x speed, DVD-R DL at up to 2x speed, DVD+R DL at up to 2.4x speed and DVD-RAM at up to 3x speed.
Introduction HD DVD-RW drive Some models are equipped with a full-size HD DVD-RW drive module that allows you to run CD/DVD/HD DVDs without using an adaptor. The drive reads DVD-ROMs at a maximum 8x speed, CD-ROMs at a maximum 24x speed, and HD DVD-ROMs at a maximum 2.4x speed. It writes CD-Rs at up to 16x speed, CD-RWs at up to 4x speed, DVD-Rs and DVD+Rs at up to 4x speed, DVD-RWs and DVD+RWs at up to 4x speed, DVD-R DL at up to 2x speed, DVD+R DL at up to 2.
Introduction Keyboard Built-in 86 keys or 87 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5, The Keyboard, for details. Pointing device Built-in A touchpad and control buttons in the palm rest enable control of the on-screen pointer. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar.
Introduction Infrared receiver window This is a sensor window that receives signals from the remote controller which is provided with your computer. (Provided with some models) Slots Multiple digital media This slot allows you to easily transfer data from slot devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/SDHC/MS/MS Pro/MMC/xD memory cards).
Introduction Modem Some computers in this series are equipped with an internal modem. The internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in . The speed of date transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada. Only V.90 is available in other regions.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. To access the Power Options, click Start → Control Panel → System and Maintenance → Power Options. User’s Manual Hot keys Key combinations allow you to quickly modify the system configuration directly from the keyboard without running a system configuration program.
Introduction User’s Manual Panel power on/off This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. This can be specified in the Power Options. Low battery automatic hibernation mode When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters hibernation and shuts down. This can be specified in the Power Options.
Introduction TOSHIBA Value Added Package This section describes the TOSHIBA Component features preinstalled on the computer. TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Button Support This utility controls the following computer button functions. ■ Mute button ■ CD/DVD/HD DVD button The starting application from the button can be changed.
Introduction Utilities and applications This section describes preinstalled utilities and tells how to start them. For details on operation, refer to each utility’s online manual, help files or readme.txt files TOSHIBA Assist User’s Manual TOSHIBA Assist is a graphical user interface that provides easy access to help and services. HW Setup utility To start the utility, click the Windows Start button, point to All Programs, click TOSHIBA, click Utilities, and select HWSetup icon.
Introduction TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. You can boot ConfigFree from the menu bar as follows.
Introduction Fingerprint utility cannot be used in models that do not have a fingerprint module installed. Windows Mobility Center This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center. ■ Lock Computer: This can be used to lock your computer without turning it off.
Introduction User’s Manual Battery Pack An additional battery pack 3 cell type (PA3533U1BRS/ PA3533U-1BAS), 6 cell type (PA3534U1BRS/ PA3534U-1BAS) and 9 cell type (PA3535U-1BRS/ PA3535U-1BAS) can be purchased from your TOSHIBA dealer. The battery pack is identical to the one that came with your computer. Use it as a spare or replacement.
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position.
The Grand Tour Front edge logo Front edge logo indicates the computer series you bought. (The availability of this function depends on the model you purchased.) Wireless communication switch Slide this switch toward the right of the computer to turn on Wireless communication. Slide it toward the left of the computer to turn off the functions. (Provided with some models) Set the switch to turn off in airplanes and hospitals. Check the Wireless communication indicator.
The Grand Tour Left side Figure 2-2 shows the computer’s left side. LAN JACK FAN VENT EXPRESSCARD SLOT VIDEO-OUT PORT* HDMI OUT PORT* EXTERNAL MONITOR PORT USB PORTS I.LINK (IEEE1394) PORT *DEPENDING ON THE MODEL YOU PURCHASED Figure 2-2 The left side of the computer External monitor port This 15-pin port allows you to connect an external monitor. Fan vent Provides air flow for the fan. Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vents.
The Grand Tour Universal serial bus (USB 2.0) ports The two universal serial bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. The ports with the icon ( ) has USB Sleep and Charge function and also support USB 1.1. Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. Operation of all functions of all USB devices has not been confirmed.
The Grand Tour Right side Figure 2-3 shows the computer’s right side. MODEM JACK* SECURITY LOCK SLOT OPTICAL DISC DRIVE USB PORTS DC IN 19V FM TUNER JACK* *DEPENDING ON THE MODEL YOU PURCHASED. Figure 2-3 The right side of the computer Universal serial bus (USB 2.0) ports The two universal serial bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards.
The Grand Tour Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack that allows you to use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions. (Provided with some models) FM tuner jack A FM tuner jack enables FM tuner antenna connection. Optical disc drive A DVD Super Multi (+-R DL) drive, a HD DVDROM drive or a HD DVD-RW drive. DC IN 19V The AC adaptor connects to this socket.
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. BATTERY PACK BATTERY PACK LOCK BATTERY RELEASE LATCH MEMORY MODULE COVER Figure 2-5 The underside of the computer User’s Manual Battery pack The battery pack powers the computer when the AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-up Modes, describes how to access the battery pack.
The Grand Tour Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, lift the display up and position the display at a comfortable viewing angle. WEB CAMERA* BUILT-IN MICROPHONE* WEB CAMERA LED* DISPLAY SCREEN FUNCTION BUTTON* STEREO SPEAKER (RIGHT)** POWER BUTTON FINGERPRINT SENSOR* TOUCHPAD CONTROL BUTTONS STEREO SPEAKER (LEFT)** TOUCHPAD SYSTEM INDICATORS *PROVIDED WITH SOME MODELS.
The Grand Tour User’s Manual Fingerprint sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled (Provided with some models): ■ Logon to Windows and access a securityenabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented. ■ Disable the password-protected screen-saver when returning from power-saving (Sleep) mode. ■ Single-Swipe Sign-On feature.
The Grand Tour Please handle your computer carefully to avoid scratching or damaging the surface. Function button Six buttons are provided with some models. Available for use: Mute, CD/DVD/HD DVD, Play/Pause, Stop, Previous, Next. These buttons allow you to manage audio/video, run applications and access utilities. Refer to the Function button section in Chapter 4, Operating Basics for details. User’s Manual Mute button Press this button to turn off the sound.
The Grand Tour System indicators Figure 2-7 shows the system indicators, which light when various computer operations are in progress. MULTIPLE DIGITAL MEDIA CARD HDD/ODD MAIN BATTERY DC IN POWER Figure 2-7 System indicators User’s Manual DC IN The DC IN indicator glows white/green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator shows no light.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CAPS LOCK indicator. When the CAPS LOCK indicator glows the keyboard is in all-caps mode. CAPS LOCK INDICATOR Figure 2-8 CAPS LOCK indicator CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. When the F10 key indicator glows the keypad overlay allows you to control the cursor.
The Grand Tour Optical disc drive A DVD Super Multi (+-R DL) drive, a HD DVD-ROM drive or a HD DVD-RW drive. When the computer is accessing a CD/DVD/HD DVD, an indicator on the drive glows. About the HD DVD This section describes the features, use of HD DVD and HD DVD Media. Summary HD DVD allows users to enjoy video, concerts and other packaged content by taking advantage of its large amount of storage space and high-quality audio and video.
The Grand Tour ■ Viewing of HD DVD content on an external display requires a HDCP capable HDMITM or DVI input on the external display. ■ Make sure to connect the computer's AC adaptor when playing a HD DVD. ■ CPU power is concentrated on HD DVD playback when playing a HD DVD, so make sure to exit all other applications. ■ Dolby Digital audio enhancements are only supported by Microsoft® Windows® operating system.
The Grand Tour Writable discs This section describes the types of writable CD/DVD/HD DVD discs. Check the specifications for your drive to for the type of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics. CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4 to 10 speed discs.
The Grand Tour DVD Super Multi (+-R DL) drive The full-size DVD Super Multi drive (+-R DL) module allows you to record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour HD DVD-RW drive The full-size HD DVD-RW drive module allows you to record data to rewritable CDs as well as run either 12 cm (4.72") HD DVD,12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour Full size remote controller PLAY PAUSE POWER RECORD STOP REWIND FAST FORWARD REPLAY BACK ARROWS SKIP MORE INFORMATION START OK VOLUME + VOLUME GUIDE MUTE CHANNEL/PAGE LIVE TV RECORDED TV DVD MENU NUMBERS CLEAR ENTER Figure 2-10 Full size remote controller User’s Manual 2-18
The Grand Tour User’s Manual Power Starts or terminate the operating system. This button functions like the power button of your computer. By default, the Sleep mode is equivalent to the power off state of your computer. To change the setting, click Start → Control panel → System and Maintenance → Power Options → Choose what the Power button does. The following four options are available: Do nothig, Sleep, Hibernate and Shut down.
The Grand Tour User’s Manual More information The button provides more detail information. Arrows Moves the cursor to navigate within Media Center windows. OK Selects the desired action or window option. It acts like the ENTER Key. Volume + Increases the volume while viewing DVDs or replaying CDs. Volume - Decreases the volume while viewing DVDs or replaying CDs. Start Opens Media Center to the main window.
The Grand Tour Numbers Allows you to select a channel or chapter number while CD/DVD replay. Numbers, letters or symbols can be entered. To select a channel or chapter number of two or more digits, press the buttons sequentially. For example, press the “1” button and then the “0” button to select the number 10. CLEAR Deletes entered numbers, letters or symbols. ENTER The OK button on the remote controller has the same functions.
The Grand Tour User’s Manual Brightness up Increases the computer’s display panel brightness in individual steps. Power Starts or terminate the operating system. This button functions like the power button of your computer. By default, the Sleep mode is equivalent to the power off state of your computer. To change the setting, click Start → Control panel → System and Maintenance → Power Options → Choose what the Power button does.
The Grand Tour Start Opens Media Center to the main window. Rewind Moves the media (video, DVD, music, and so on) backwards. Play/Pause Plays the selected media. This button also acts as a pause button. Fast forward Moves the media (video, DVD, music, and so on) forwards. Replay Moves media backward (seven seconds for videos, one music track or one DVD chapter at a time). Stop Stops the media currently playing.
The Grand Tour 30 DEGREES 15 DEGREES (VERTICALLY) INFRARED RECEIVER WINDOW 30 DEGREES 5M REMOTE CONTROLLER* *THE APPEARANCE OF THE PROVIDED REMOTE CONTROLLER MAY VARY FROM MODEL TO MODEL, AND IT IS NOT PROVIDED WITH SOME MODELS. Figure 2-12 Operational range of the remote controller Even if within the effective scope as described above, the remote controller may malfunction or not work correctly in the following cases.
The Grand Tour Installing/Removing batteries Be sure to install the provided AA type or CR2016 type batteries before using the remote controller. The procedures for installing and removing the batteries vary depending on the type of the remote controller. Check the type and then install or remove the batteries as instructed. Store the battery for the remote controller beyond the reach of children. If a child swallows a battery, this might result in choking. If it happens, contact a doctor immediately.
The Grand Tour Installing the batteries Full size remote controller 1. Open the battery cover on the back side of the remote controller. Slide the cover in the direction of the arrow to remove the cover. BATTERY COVER Figure 2-13 Opening the battery cover 2. Insert the batteries in place. Be sure to place the batteries with their polarities (+ and -) in the correct position. BATTERIES Figure 2-14 Inserting the batteries 3. Close the battery cover.
The Grand Tour Slim size remote controller 1. Open the battery cover on the back side of the remote controller. BATTERY COVER Figure 2-16 Opening the battery cover 2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. STOPPER BATTERY Figure 2-17 Inserting the batteries 3. Close the battery cover.
The Grand Tour Replacing the batteries When the batteries in the remote controller reach the end of their life, the remote controller may not operate correctly or work only within a short distance from your computer. In this instance, you should purchase new batteries and replace the discharged ones. Full size remote controller 1. Open the battery cover on the back side of the remote controller. 2. Replace the batteries.
The Grand Tour Placing slim size remote controller Inserting a slim size remote controller To insert the slim size remote controller, follow the setps below. 1. Make sure the ExpressCard slot is empty. 2. Set the front side upward and insert the slim size remote controller. SLIM SIZE REMOTE CONTROLLER Figure 2-21 Inserting the slim size remote controller 3. Press gently to ensure a firm connection. Remove a slim size remote controller To remove the slim size remote controller, follow the setps below.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-up Modes for details.
Chapter 3 Getting Started This chapter provides basic information to start using your computer. It covers the following topics: Be sure also to read Instruction Manual for Safety and Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-up Modes.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. To open the display, lift the panel up and adjust it to the best viewing angle. While you open the display, hold the base of the computer to avoid raising it.
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of three modes:shut down (Boot) , hibernation mode or sleep mode. Shut down mode (Boot mode) When you turn off the power in shut down mode, no data is saved and the computer will boot to the operating system’s main screen. 1.
Getting Started Benefits of hibernation mode The hibernation feature provides the following benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in the Hibernate tab in Power Options. Otherwise, the computer will shut down in sleep mode. If battery power becomes depleted, data saved in sleep mode will be lost.
Getting Started Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD/ODD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Getting Started Executing sleep mode You can also enable sleep mode by pressing FN + F3. See Chapter 5, The Keyboard, for details. You can enter sleep mode in one of three ways: 1. Click Windows Start button, point to , and then click Sleep. 2. Close the display panel. This feature must be enabled. Refer to the Power Options in the Control Panel. 3. Press the power button. This feature must be enabled. Refer to the Power Options in the Control Panel.
Getting Started System recovery options About 1.5 GB hidden partition is allocated on the hard disk drive for the system recovery options. This partition stores files which can be used to repair the system in the event of a problem. System recovery options The system recovery options feature is installed on the hard disk when shipped from the factory. The system recovery options menu includes some tools to repair startup problems, run diagnostics or restore the system.
Getting Started Restoring the preinstalled software from the recovery HDD A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore preinstalled software in the event of a problem. When re-setting up your hard disk, do not change, delete or add partition in a manner other than specified in the manual. Otherwise, space for software may be destroyed.
Getting Started b. Press the F9 key to set to default settings, and select Yes. c. Press the F10 key to save the changes, and select Yes. d. When the TOSHIBA Leading Innovation>>> prompt appears, press the F12 key to display the Boot menu. Go to the (3.)step. 3. Use the up or down cursor key to select CD/DVD in the display menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup and Passwords. 4. A menu appears. Follow the on-screen instructions.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the touchpad, the fingerprint sensor, optical disc drives, Audio/Video controls, the web camera, the microphone, the internal modem, the FM tuner, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVD/HD DVDs. Using the touchpad To use the touchpad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Fingerprint sensor TOUCHPAD CONTROL BUTTONS TOUCHPAD Figure 4-1 Touchpad, touchpad control buttons and fingerpring sensor Using the fingerprint sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard.
Operating Basics How to swipe the finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: 1. Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you. 2. While lightly touching the sensor, swipe the finger towards you until the sensor surface becomes visible. 3. Ensure the center of the fingerprint is on the sensor when swiping the finger.
Operating Basics Points to note about the fingerprint sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects. ■ Do not press the sensor strongly. ■ Do not touch the sensor with a wet finger or any wet objects. Keep sensor surface dry and free of water vapor.
Operating Basics ■ The fingerprint for each finger is different and unique. Please ensure that only the registered or enrolled fingerprint or fingerprints are used for identification. ■ Check sliding position and speed. ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.
Operating Basics Fingerprint sensor limitations ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. ■ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration. ■ The recognition success rate may differ from user to user. ■ Toshiba does not guarantee that this fingerprint recognition technology will be error-free.
Operating Basics 2. The Enter Windows Password screen is displayed. Enter a password into the Enter Windows Password field. Click Next. 3. The Control Center screen is displayed. Click the non-enrolled finger icon above the finger. 4. The Fingerprint Enrollment screen is displayed. Confirm the message and click Next. 5. The Scanning Practice screen is displayed. You can practice swiping your finger. When you have finished practicing swiping your finger, click Next. 6.
Operating Basics Fingerprint system boot authentication General The fingerprint authentication system can be used to replace the keyboardbased User Password authentication system when booting up. If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, press the ESC key or click Switch User button when the Fingerprint System Bootjuhu Authentication screen is displayed.
Operating Basics Fingerprint Single-Swipe Sign-On feature General This is a feature that allows the user to complete the authentication for both the User Password (and optionally, the HDD user and Supervisor passwords) and logging on to Windows using only one fingerprint authentication when booting up. It is necessary to register the User Password and Windows Logon password before using the fingerprint PreOS feature and this fingerprint Single Sign-On feature.
Operating Basics USB Sleep and Charge function Your computer can supply USB bus power (DC5V) to the USB port even when the power of the computer is turned OFF. "Power OFF" includes sleep mode, hibernation mode or shutdown state. This function can only be used for ports that support the USB Sleep and Charge function (hereinafter called "compatible ports"). Compatible ports are USB ports that have the ( ) symbol icon.
Operating Basics How to enable/disable USB sleep and charge function You can set enable/disable USB sleep and charge function in HW setup. Please refer to the USB Sleep and Charge function in Chapter7. Using optical disc drives The text and illustrations in this section refer primarily to the optical disc drive. However, operation is the same for all other optical disc drives. The full-size drive provides high-performance execution of CD/DVD/HD DVDsbased programs.
Operating Basics b. Pressing the eject button will not open the drawer when the drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. EJECT HOLE Figure 4-4 Manual release with the eject hole 2. Grasp the drawer gently and pull until it is fully opened.
Operating Basics 3. Lay the CD/DVD/HD DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD/HD DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD/HD DVD tray. Therefore, you will need to turn the CD/DVD/HD DVD at an angle when you place it in the tray. After seating the CD/DVD/HD DVD, however, make sure it lies flat, as shown in above figure. ■ Do not touch the laser lens. Doing so could cause misalignment.
Operating Basics 5. Push the center of the drawer to close it. Press gently until it locks into place. If the CD/DVD/HD DVD is not seated properly when the drawer is closed, the CD/DVD/HD DVD might be damaged. Also, the drawer might not open fully when you press the eject button. Figure 4-7 Closing the drawer Removing discs To remove the CD/DVD/HD DVD, follow the steps below and refer to below figure. Do not press the eject button while the computer is accessing the drive.
Operating Basics 2. The CD/DVD/HD DVD extends slightly over the sides of the drawer so you can grasp it. Hold the CD/DVD/HD DVD gently and lift it out. Figure 4-8 Removing a CD/DVD/HD DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. Function button This section describes about Function button. Six buttons are provided with some models.
Operating Basics Using TOSHIBA HD DVD PLAYER to enjoy HD DVDs HD DVD playback restrictions HD DVD-ROM drive and HD DVD-RW drive model allow users to enjoy the strong visuals of HD DVD Video. TOSHIBA HD DVD PLAYER software is provided for playback of HD DVD Video. Notes on use HD DVD playback ■ HD DVD is a new standard which makes use of new technologies. As such, there is a possibility of problems occurring related to connection, compatibility or operation with some discs and other digital devices.
Operating Basics When using ■ Frame dropping, audio skipping or out of synch audio and video may occur during playback of some HD DVD Video titles. ■ Close all other applications when using the TOSHIBA HD DVD PLAYER. Do not open any other applications or carry out any other operations during HD DVD Video playback. Playback may stop or not function properly in some situations. ■ Do not playback HD DVD discs Video while watching or recording television programs using other applications.
Operating Basics ■ When viewing on an external display or television, use a HDMI cable to connect the external device to the HDMI out port and change the display device before playing. The display device cannot be changed during playback. ■ HD DVD Video can only be displayed on the computer's display panel or televisions connected to the computer's HDMI out port. HD DVD Video cannot be displayed on televisions connected to the S-Video output connector or external displays connected to the RGB connector.
Operating Basics Using TOSHIBA HD DVD PLAYER Starting TOSHIBA HD DVD PLAYER 1. Use the following procedure to start TOSHIBA HD DVD PLAYER. Insert a HD DVD-Video in the HD DVD drive while Windows Vista™ is running. When a HD DVD-Video disc and a HD DVD (Twin format disc) are set in the HD DVD drive, the following application selection screen may appear. If this occurs, select Play HD DVD movie or Run the HD DVD Launcher, then click OK to launch the TOSHIBA HD DVD PLAYER.
Operating Basics ■ Only operation buttons (including remote controller and Front operation panels) which correspond to currently available and active features will be useable during HD DVD playback. ■ If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, touchpad and mouse menu operations may not be able to be used.
Operating Basics Help Opens help. Minimize Minimizes the window of TOSHIBA HD DVD PLAYER. Exit Closes TOSHIBA HD DVD PLAYER. TOSHIBA HD DVD PLAYER control window The buttons on the panel are used to control playback of HD DVD-Video discs. Click the Display Area to display the Control window when it is hidden. Please refer to the following "TOSHIBA HD DVD PLAYER control window" section for more information.
Operating Basics Current position Displays the current position within the title on the bar icon. Volume control Adjusts the volume to the level selected by dragging the slider bar. Mute Mutes the sound when clicked. Clicking when the sound is muted returns the volume to the previous level. Multi audio channel output Switches between available multi audio channel, during playback of a DVD-VR. This function can be used during playback of a DVD-VR only.
Operating Basics ANGLE TWIN FORMAT DISC (HD DVD SELECTED) TWIN FORMAT DISC (DVD SELECTED) SOUND SUBTITLE REPEAT TITLE/CHAPTER SEARCH TOP MENU MENU DRIVE SPECIFICATION RETURN Figure 4-14 TOSHIBA HD DVD PLAYER control window (3) Subtitle Switches between available subtitles. Sound Switches between audio tracks for titles which have more than 1 audio track. Angle Switches between angles for multi-angle compatible titles.
Operating Basics Using the computer in place of a HD DVD PLAYER Videos played using TOSHIBA HD DVD PLAYER included with the computer can be displayed on a television equipped with a HDMI input port. HD DVD-Video can only be displayed on the computer's display panel or on a television connected to the HDMI out port. HD DVD-Video cannot be displayed on televisions connected to the S-Video out port or external displays connected to the RGB connector.
Operating Basics audio. The volume level for both the television and computer can be adjusted using the WAVE item in Volume Control. Switching between computer and television display The following method can be used to display HD DVD-Video. The display method can be changed by changing the display device setting. Configure the following settings to display HD DVD-Video on the television. If the following settings are not configured, HD DVD-Video will not be displayed on the television.
Operating Basics Writing CD/DVDs on DVD Super Multi (+-R DL) drive/HD DVDROM drive Some models are equipped with a full-size DVD Super Multi (+-R DL ) drive or HD DVD-ROM drive, which can be used to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM/+R DL/-R DL discs. The following applications for writing are supplied: TOSHIBA Disc Creator. Ulead DVD MovieFactory® for TOSHIBA, which is a product of Ulead Systems, Inc.
Operating Basics DVD-RW: DVD Specifications for DVD-RW Disc for General Version 1.2 MITSUBISHI KAGAKU MEDIA CO., LTD. VICTOR COMPANY OF JAPAN, LTD. DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, 2.1 or 2.2 MATSUSHITA ELECTRIC INDUSTRIAL CO., LTD. HITACHI MAXELL LTD. DVD+R DL: MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-R DL: MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-R for Labelflash™: FUJIFILM CORPORATION. DVD+R for Labelflash™: FUJIFILM CORPORATION.
Operating Basics ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs. ■ Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in whole or in part. ■ Data deleted (erased) from a CD-RW and DVD-RW, DVD+RW and DVD-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.
Operating Basics ■ ■ ■ ■ ■ ■ Apply impact or vibration to the PC. ■ Install, remove or connect external devices, including items such as a SD/SDHC memory card, ExpressCard, Memory Stick/Memory Stick Pro, xD picture card, MultiMediaCard, USB device, external monitor, i.LINK device, or an optical digital device. ■ Use the Audio/Video control button to reproduce music or voice. ■ Open the optical disc drive. Do not use shut down/log off and sleep/hibernation while writing or rewriting.
Operating Basics Writing CD/DVD/HD DVDs on HD DVD-RW drive The optical drive installed on this computer cannot write multiple sessions on HD DVD-R DL disc sessions. Once a disc has been written to once, it will be finalized. Once finalized, no further writing to the disc will be possible regardless of what portion of the total disc capacity was used.
Operating Basics Legal footnotes TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R, CD-RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM, HD DVD-R, HD DVD-R DL or HD DVD-RW disc that may be caused by writing or rewriting with this product.
Operating Basics DVD-R: DVD Specifications for DVD-R Disc for General Version 2.0 HITACHI MAXELL, LTD. TAIYO YUDEN CO., LTD. DVD-R DL: MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-RW: DVD Specifications for DVD-RW Disc for General Version 1.2 VICTOR COMPANY OF JAPAN, LTD. DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD. RICOH CO., LTD. DVD+R DL: MITSUBISHI KAGAKU MEDIA CO., LTD. DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. RICOH CO., LTD. DVD-RAM: VD Specifications for DVD-RAM Disc for Version 2.0, 2.1 or 2.
Operating Basics ■ This drive cannot use discs that allow writing faster than 4x speed (DVD-R, DVD+R, DVD-RW and DVD+RW media), 3x speed (DVDRAM media), 2.4x speed (DVD+R DL media), 2x speed (DVD-R DL and HD DVD-R media) and 1x speed(HD DVD-R DL and HD DVD-RW media). ■ Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable. ■ 2.6 GB and 5.2 GB DVD-RAM media cannot be read nor written. ■ DISC created in DVD-R DL format4 (Layer Jump Recording) cannot be read.
Operating Basics ■ Before you enter either sleep mode or hibernation mode, take care to ensure that any DVD-RAM writing has been completed. In this instance, writing is finished if you can eject the DVD-RAM media. ■ Be sure to close all other software programs except for the writing software itself. ■ Do not run software such as a screen saver which can put a heavy load on the processor. ■ Operate the computer at its full power settings - do not use any powersaving features.
Operating Basics ■ ■ ■ ■ ■ Do not use shut down, log off, sleep mode or hibernation mode functions while writing or rewriting. Make sure that the write/rewrite operation is completed before going into either sleep mode or hibernation mode (writing is completed if you can remove an optical disc on the HD DVD-RW drive). If the media is of poor quality, or is dirty or damaged, writing or rewriting errors may occur.
Operating Basics ■ If you add data to a DVD-R, DVD-R DL, DVD+R, DVD+R DL, HD DVDR or HD DVD-RW disc that you have already recorded to, you might not be able to read the added data under some circumstances. For example, it cannot be read under 16-bit operating systems, such as Windows 98SE and Windows Me, while in Windows NT4 you will need Service Pack 6 or later, and in Windows 2000, you will need Service Pack 2.
Operating Basics Video You can record video using Ulead DVD MovieFactory® for TOSHIBA. When using Ulead DVD MovieFactory® for TOSHIBA How to make a Labelflash DVD Simplified steps for making a Labelflash DVD: 1. Insert a Labelflash disc in DVD drive. Set PRINTING SIDE for underside. 2. Click Start → All Programs → DVD MovieFactory for TOSHIBA → Ulead DVD MovieFactory for TOSHIBA Laucher to lanuch DVD MovieFactory. 3. Click Print Disc Label → Label Printing. Ulead Label@Once is started. 4.
Operating Basics Simplified steps for making a DVD-Video from adding video source: 1. Click Start → All Programs → DVD MovieFactory for TOSHIBA → Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Click Video Disc → New Project to invoke 2nd Launcher, choose your project type, then invoke DVD MovieFactory. 3. Add source from HD Disk by click Add Video files button to invoke browser dialog box. 4. Choose the source video then go to Next page to apply Menu. 5.
Operating Basics 2. Before recording the video to DVD ■ When you record DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: ■ Operate the computer for any other function, including using a mouse or touchpad, or closing/opening the display panel. ■ Bump or cause vibration to the computer.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVD/HD DVD. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVD/HD DVD 1. Store your CD/DVD/HD DVD in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD/HD DVD. 3. Do not write on, apply a sticker to, or otherwise mark the surface of the CD/DVD/HD DVD that contains data. 4.
Operating Basics Using the software The web camera software is pre-configured to start when you turn on Windows VistaTM; if you need to restart it go to Start → All Programs → Camera Assistant Software → Camera Assistant Software. VIDEO RECORDING AUDIO RECORDING CAPTURE STILL IMAGES FUNCTION DISPLAY WINDOW CAMERA RESOLUTION EFFECTS MUTE Figure 4-17 Using the Software User’s Manual Capture Still Image Click to see a preview of the captured image; you can also e-mail the image.
Operating Basics Settings Chooses from the : Options tab to change the tool position; the Picture tab to select picture output options such as size, export file and saving location; the Video tab to choose output settings such as Frame Rate, Size, Compression and the file save path; the Audio Device, Compression,Volume and file save path. Help Displays the help files for the software.
Operating Basics Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. To select a region, follow the steps below. 1. In Windows Vista™, click Start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Operating Basics Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Operating Basics Do not pull on the cable or move the computer while the cable is connected. Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. Using the FM tuner The availability of this feature is depending on the model you purchased. 1. Plug the FM tuner antenna into the FM tuner jack.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE 802.11 wireless LAN standard (Revision A, B, G or draft N). Supported features.
Operating Basics BluetoothTM wireless technology BluetoothTM wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth Adaptor simultaneously. BluetoothTM wireless technology has the following features: Worldwide operation The Bluetooth radio transmitter and receiver operates in the 2.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application. If you used the Task Bar to disable Wireless LAN, restart the computer or follow the procedures below to enable the system to recognize Wireless LAN.
Operating Basics Connecting LAN cable The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 Mbit/s, 100BASE-TX), be sure to connect with a category 5 cable, CAT5, or higher. If you are using Ethernet LAN (10 Mbit/s, 10BASE-T), connect with a category 3 cable, CAT3, or higher.
Operating Basics Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Make sure the LAN active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. These functions are controlled within the Power Options.
Chapter 5 The Keyboard The computer's keyboard layout is compatible with 104/105-key enhanced keyboard. Pressing FN key and other keys can execute all enhaced keyboard function. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, function keys, soft keys, Windows special keys and keypad overlay.
The Keyboard Function keys: F1 … F12 The function keys, not to be confused with FN, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the FN key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: FN key combinations, in this chapter.
The Keyboard Press FN + F12 (Scroll Lock) to lock the cursor on a specific line. The power on default is off. Press FN + ENTER to simulate ENTER on the enhanced keyboard’s numeric keypad. Press FN + CTRL to simulate the enhanced keyboard’s right CTRL key. Press FN + ALT to simulate the enhanced keyboard’s right ALT key. Hot keys Hot keys (pressing FN + a function or ESC key) allow you to enable or disable certain features of the computer.
The Keyboard Power plan: Pressing FN + F2 changes the power settings. Sleep: Pressing FN + F3 switches the system to sleep mode. Hibernate: Pressing FN + F4 switches the system to hibernation mode. Output: Pressing FN + F5 changes the active display device. Brightness down: Pressing FN + F6 decreases the computer’s display panel brightness in individual steps. Brightness up: Pressing FN + F7 increases the computer’s display panel brightness in individual steps.
The Keyboard Wireless: Pressing FN + F8 switches the active wireless devices if the wireless communication switch is switched on. If your wireless communication device is not installed, a dialog box will not appear. Touchpad: Pressing FN + F9 enables or disables the touchpad function. Zoom: Pressing FN + SPACE changes the display resolution. TOSHIBA zooming utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button.
The Keyboard Numeric mode To turn on the Numeric mode, press FN + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-1. Press FN + F11 again to turn off the overlay. Figure 5-1 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without turning off the overlay : 1. Hold FN and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing SHIFT. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing SHIFT. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down ALT. 2. Using the overlay keys, type the ASCII code. 3.
Chapter 6 Power and Power-up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power-up modes.
Power and Power-up Modes Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery blinking orange DC IN off Battery charge is exhausted Computer goes into hibernation or shuts down (depending on the Toshiba power Management Utility Setting) No battery installed • No operation •LED: Battery off DC IN off Power off (no operation) Power indicators The Battery
Power and Power-up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected. Indicates the AC adaptor is connected and White/Green supplying proper power to the computer. Orange Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light.
Power and Power-up Modes Battery When the AC power cord is not connected, the computer’s main power source is a removable lithium ion battery pack, also referred to in this manual as the battery. You can purchase additional battery packs for extended use of the computer away from an AC power source. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Power and Power-up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-up Modes explode or leak caustic liquid and cause death or serious injury. It could also fail or malfunction causing data lose. 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet.
Power and Power-up Modes leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely. Sleep and hibernation will not function and data in memory will be lose. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7.
Power and Power-up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (3 cell) 8 hours or more 2 hours Battery pack (6 cell) 8 hours or more 3 hours Battery pack (9 cell) 8 hours or more 4 hours RTC battery 24 hours 24 hours The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-up Modes Monitoring battery capacity Remaining battery power can be monitored in Power Options. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods.
Power and Power-up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install battery packs.
Power and Power-up Modes 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. BATTERY PACK Figure 6-2 Removing the battery pack 7. Pull the battery pack forward to remove it. For environmental reasons, do not throw away a spent battery pack. Please return spent battery pack to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Power and Power-up Modes Starting the computer by password If you have already registered a password, there are two ways to start the computer: ■ Swipe your fingerprint on the sensor if you have already registered the fingerprint with the Fingerprint utility and enabled Fingerprint Power-on Security. If you would not like to swipe your finger or cannot authenticate the fingerprint for some reasons, press the ESC key or click Switch User button to skip the fingerprint authentication screen.
Power and Power-up Modes Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in sleep or hibernation mode but not in boot mode. If the panel power off function is enabled and use Shut down Windows, do not close the display until the shut down function is completed. System auto off This feature turns the system off automatically if it is not used for a set duration.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup allows you to configure settings for General, Password, Display, CPU, Boot Priority, Keyboard, USB, LAN and LED. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default and About. Default Returns all HW Setup values to the factory settings. About Displays the HW Setup version. Setup This field displays the installed BIOS version and date. Password User Password This option allows you to set or reset the user password for power on. Changes or remove the password. (Default) Not Registered Registered Sets the password.
HW Setup and Passwords To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** 3. Click the OK button. If the character string you enter matches the registered password, the password option is reset and the display changes to: Not registered If they do not match, the following message appears. You must repeat step 1.
HW Setup and Passwords CPU Dynamic CPU Frequency Mode This option allows you to choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed.
HW Setup and Passwords If there are 2 HDDs, the Boot Priority Options setting will be like the following. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB diskette drive. N Selects the network. 1 Selects the primary HDD. 2 Selects the secondary HDD. C Selects the CD-ROM*. This procedure does not affect the settings.
HW Setup and Passwords Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in sleep mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in sleep mode. Enabled Enables the Wake-up on Keyboard. Disabled Disables the Wake-up on Keyboard. (Default) USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation.
HW Setup and Passwords LAN Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Enables the Wake-up on LAN. (Default) Disabled Disables the Wake-up on LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. Built-in LAN Enabled Enables built-in LAN functions.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA dealer: Cards/Memory ■ ExpressCard ■ SD, SDHC, MS, MS Pro, MMC, xD memory cards ■ Memory expansion Power devices ■ Additional battery pack (3 cell, 6 cell and 9 cell) ■ Additional AC adaptor Peripheral devices ■ ■ ■ ■ ■ USB FDD Kit External monitor Television HDMI i.
Optional Devices ExpressCard Installing an ExpressCard The ExpressCard slot is located on the left side of the computer. You can install one ExpressCard in the slot. Windows’ hot-install feature allows you to install ExpressCard while the computer’s power is on. Do not install an ExpressCard while the computer is in sleep or hibernation mode. Some cards might not work properly. To install an ExpressCard, follow the steps below. 1. There is a dummy card in the slot.
Optional Devices 2. Grasp the dummy card and pull it out from the slot. DUMMY CARD Figure 8-2 Removing the dummy card 3. Insert the ExpressCard. 4. Press gently to ensure a firm connection. 5. Check the configuration in the HW Setup window to make sure it is appropriate for your card.
Optional Devices Removing an ExpressCard To remove the ExpressCard, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the ExpressCard. 2. Press the ExpressCard slightly to make it stretch out. 3. Grasp the ExpressCard and pull it out from the slot.
Optional Devices Multiple digital media card slot The computer is equipped with a multiple digital media card slot that can accommodate Secure Digital (SD)/ Secure Digital High Capacity (SDHC)/ Memory Stick (MS)/Memory Stick Pro (MS Pro)/Multi Media Card (MMC)/xD memory cards. These memory cards allow you to easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/SDHC/MS/MS Pro/MMC/xD memory cards.
Optional Devices Installing a SD/SDHC/MS/MS Pro/MMC/xD card To install the memory card, follow the steps below. 1. Insert the memory card. 2. Press gently to ensure a firm connection. SD/SDHC/MS/MS PRO/MMC/XD CARD* MULTIPLE DIGITAL MEDIA CARD SLOT *THE CARD’S SHAPE DEPENDS ON THE CARD YOU PURCHASED Figure 8-5 Inserting the memory card ■ Keep foreign objects out of the multiple digital media card slot. A pin or similar object can damage the computer's circuitry.
Optional Devices Removing a SD/SDHC/MS/MS Pro/MMC/xD card To remove the memory card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the inserted memory card. 2. Gently press the memory card inside the socket to eject it. 3. Grasp the card and remove it.
Optional Devices Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3. ■ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. ■ Do not try to install a memory module with the computer turned on or turned off in sleep and hibernation mode.
Optional Devices 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7. Push the module down so that it lies flat and is secured by two latches. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Figure 8-8 Inserting the memory module Figure 8-9 Pushing the memory module down 8. Seat the cover and secure it with one screw. 9.
Optional Devices Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. ■ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. ■ Do not try to remove a memory module with the computer turned on or turned off in sleep and hibernation mode.
Optional Devices Additional battery pack (3 cell, 6 cell and 9 cell) You can increase the portability of the computer with additional battery packs (3 cell: PA3533U-1BRS/PA3533U-1BAS, 6 cell: PA3534U1BRS/PA3534U-1BAS, 9 cell: PA3535U-1BRS/PA3535U-1BAS). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-up Modes.
Optional Devices To change the display settings, press FN + F5. If you disconnect the monitor before you turn the computer off, be sure to press FN + F5 to switch to the internal display. Refer to Chapter 5, The Keyboard, for details on using hot keys to change the display setting. If you set LCD+Analog RGB for the computer’s display, you must set the computer’s display resolution to the same as that of the external monitor or other device, such as a projector.
Optional Devices 1. Plug one end of the HDMI cable into the HDMI port of the HDMI device. Figure 8-12 Connecting a HDMI cable 2. Plug the other end of the HDMI cable into the HDMI out port on your computer. Setting for display video on HDMI To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed. ■ Be Sure to use the FN + F5 hot keys to select the display device before starting to play video.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as 1. Digital video cameras 2. Hard disk drives 3. MO drives 4. CD-RW drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed. ■ Use S100, S200 or S400 cables no longer than three meters.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software or diskette. If you cannot load a software package, the media (usually a diskette) may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: TOSHIBA Leading Innovation>>> This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow white/green) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer. If the indicator still does not glow, the battery may be at the end of its operating life. Replace it. If you do not think the battery is at the end of its operating life, see your dealer.
Troubleshooting LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information. Problem Procedure No display Press hot keys FN + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the They might have come from contact with the LCD screen. keyboard or touchpad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner.
Troubleshooting DVD Super Multi(+-R DL) drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting HD DVD-ROM drive/HD DVD-RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Make sure the drive’s drawer is securely closed. You cannot access a CD/DVD/HD DVD in the Press gently until it clicks into place. drive Open the drawer and make sure the CD/DVD/HD DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD, DVD or HD DVD. Make sure there is no obstruction.
Troubleshooting Diskette drive Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the Try another diskette.
Troubleshooting Problem Procedure The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. Click Start → Control Panel → Hardware and Sound → Mouse to access it. When the reaction of Adjust the touch Sensitivity. touchpad is sensitive to 1. Open the Control Panel. slow 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6.
Troubleshooting Problem Procedure The mouse pointer moves too fast or too slow Try changing the double-click speed setting in the mouse control utility. Click Start → Control Panel → Hardware and Sound → Mouse to access it. The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentations for instructions on cleaning. If problems persist, contact your dealer.
Troubleshooting ExpressCard Refer also to Chapter 8, Optional Devices. Problem Procedure ExpressCard error occurs Reseat the ExpressCard to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. SD/SDHC/MS/MS Pro/MMC/xD card Refer also to Chapter 8, Optional Devices. Problem Procedure Memory card error occurs Reseat the memory card to make sure it is firmly connected.
Troubleshooting Problem Procedure Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting User’s Manual Problem Procedure The battery depletes quickly even when I turned OFF the power of the computer When USB Sleep and Charge function is set to [Enabled] in the HW Setup, USB bus power (DC5V) will be supplied to the external device connected to the compatible port. If external device is connected to the compatible port when the AC adaptor is not connected to the computer, the battery of the computer will be depleted even when the power of the computer is turned OFF.
Troubleshooting Modem Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Options in the Control Panel. You can hear a dial tone If the call is going through a PBX machine, make but can’t make a call sure the communication application’s tone dial detection feature is disabled. You can also use the ATX command.
Troubleshooting Sleep/Hibernation Problem Procedure The system will not Is Windows Media Player open? The system enter sleep/hibernation might not enter sleep/hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select sleep/hibernation. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth Adpater is installed in the computer. The built-in Bluetooth function and an optional Bluetooth Adpater cannot operate simultaneously.
Troubleshooting Recovery discs Problem Procedure The following message appears when executing Recovery Disc Creator. [The Recovery Disc Creator can not be launched because there is no recovery partition.] You will see this message if you have previously chosen to remove the partition and are trying to create Recovery Media. When there is no recovery partition, the Recovery Disc Creator cannot make Recovery Media.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed on the below. Outside of Europe Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Chapter 10 Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit (CPU) Performance Disclaimer.
Disclaimers Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation.
Disclaimers Battery life Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Disclaimers Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed. Non-applicable icons Certain notebook chassis are designed to accommodate all possible configurations for an entire product series.
Appendixes Table of Contents Appendix A Specifications................................................................................ A-1 Appendix B Display Controller and Modes.................................................... B-1 Appendix C V.90/V.92......................................................................................... C-1 Appendix D Wireless LAN................................................................................. D-1 Appendix E AC Power Cord and Connectors......
Appendix A Specifications This appendix summarizes the computer’s technical specifications.
Specifications Built-in modem The ability of this feature is depending on the model you purchased. Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications User’s Manual Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pixels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
Display Controller and Modes Video modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C V.90/V.92 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90/V.92. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. V.
V.90/V.92 Table Result codes for a V.90 connection No.
V.90/V.92 V42bis V.42 error control and V.42bis data compression V42 V.42 error control only NoEC No error control protocol AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect User’s Manual -V90=0 V.90 disabled -V90=1 V.
Appendix D Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications User’s Manual Form Factor ■ Mini Card Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio characteristics Radio characteristics of Wireless LAN cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4 GHz and 5 GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Table Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 1 2 3 4 5 6 7 8 9 10 11 12 13 2400-2483.5 MHz 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457*1 2462 2467*2 2472*2 When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Wireless LAN Table Wireless IEEE 802.
Appendix E AC Power Cord and Connectors The AC input plug of power cord must be compatible with various international AC power outlets. Power cords need to meet the local standards and the specifications listed as below: Length: Wire size: Current rating: Voltage rating: Minimum 1.7 meters Minimum 0.75 mm2 Minimum 2.
AC Power Cord and Connectors In Europe, two conductors power cords must be VDE type, H05VVH2-F or H03VVH2-F; while three conductors be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be 2-15P (250V) or 1-15P (125V); while three pin be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output TFT: thin-film transistor UART: universal asynchrono
Glossary ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
Glossary C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory.
Glossary Composite Video (YUV): A standard video signal used to transmit images, e.g. from a VCR to a TV. computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
Glossary Digital Audio: An audio compression standard that enables high-quality transmission and real-time playback of sound files. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record.
Glossary escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer.
Glossary K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key.
Glossary monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
Glossary pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse.
Glossary ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM. S S-Video: Short for Super-Video, a type of connection used by S-VHS videocassette players, camcorders, DVD players, etc. to transmit high-quality video signals. SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices.
Glossary TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. touchpad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Index A C AC adaptor, 1-9, 2-6, 2-30, A-1 additional, 1-18, 8-11 connecting, 3-2 problems, 9-5 safety instructions, -iii, -xxxi ASCII characters, 5-8 Checklist equipment, 1-1 problems, 9-2, 9-3 Cleaning the computer, 4-50 COM port, 4-44 B Battery charging, 6-7 life, 10-3 monitoring capacity, 6-9 Real Time Clock battery, 1-9, 6-4 remote controller, 2-25 retention time, 6-10 types, 6-3 Battery pack, 1-9, 1-18, 2-7, 6-4 additional, 8-11 extending battery life, 6-10 indicator, 2-11, 6-2 location, 2-7 operat
Index External monitor, 8-11 controller and modes, B-1 HW Setup, 7-3 port, 1-9, 2-3 problems, 9-13 F Fan vent location, 2-3 Fingerprint sensor, 2-9 location, 2-8, 4-2 problems, 9-12 using, 1-16, 4-2 FM tuner jack location, 2-5 problems, 9-20 using, 4-45 FN + 1 (TOSHIBA zooming utility reduce), 5-5 FN + 2 (TOSHIBA zooming utility enlarge), 5-5 FN + ALT (enhanced keyboard simulation), 5-3 FN + CTRL (enhanced keyboard simulation), 5-3 FN + ENTER, 5-3 FN + ESC (sound mute), 5-3 FN + F1 (lock), 5-3 FN + F12 (s
Index HW Setup accessing, 7-1 Boot Priority, 7-4 CPU, 7-4 display, 7-3 general, 7-2 keyboard, 7-6 LAN, 7-7 LED, 7-7 password, 7-2 USB, 7-6 window, 7-1 I i.
Index Modem, 1-11, 4-42, A-2, C-1 connecting, 4-44 disconnecting, 4-45 jack location, 2-5 problems, 9-17 properties menu, 4-43 region selection, 4-43 Moving the computer, 4-50 Multiple digital media card problems, 9-13 using, 8-5 N Numeric keypad, See Keypad overlay O Optical disc drive, 2-6, 2-13 indicator, 2-11 location, 2-5 safety instructions, -xiv using, 4-11 P Password fingerprint sensor, 2-9 fingerprint utility, 1-16 power on, 1-12 problems, 9-6 starting the computer with, 6-13 user, 7-2 Pointing
Index Pro/MMC/xD card, 9-13 self test, 9-4 sleep/hibernation, 9-18 sound system, 9-14 system start-up, 9-3 TOSHIBA support, 9-20 touchpad, 9-10 TV output signal, 9-14 USB, 9-15 USB mouse, 9-11 USB Sleep and Charge, 9-15 Wireless LAN, 9-18 Processor, 1-3 R Real Time Clock battery, See Battery Recovery media, 3-9 problems, 9-20 Remote controller, 2-17 battery, 2-25 placing, 2-29 using, 2-23 Restarting the computer, 3-7 S Security lock attaching, 8-15 location, 2-5 Shut down mode (boot mode), 3-4 Sleep mode
Index Wireless LAN, 1-10, 10-4 indicator, 4-48 problems, 9-18 switch, 1-11, 2-1 using, 4-46 User’s Manual Index-6
