TOSHIBA Satellite A10 Series Portable Personal Computer User’s Manual
Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
FCC information Product Name : Satellite A10 Model number : PSA10 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Canada: 1353A-L4AINT Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed.
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.
TEAC CD-ROM drive CD-224E, CDRW/DVD-ROM drive DW-224E safety instruction CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure. Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.
vermeiden darf das Gerät nicht geöffnet werden. ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
HITACHI DVD-ROM drive GDR-8082 safety instruction CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
Location of the required label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Panasonic Communications Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Table of Contents Preface Manual contents ............................................................................. xxxi Conventions ................................................................................... xxxii Abbreviations .................................................................................... xxxii Icons ................................................................................................ xxxii Keys ..................................................................
Communications ................................................................................. 1-7 Security .............................................................................................. 1-7 Software ............................................................................................. 1-7 Special features ................................................................................. 1-7 Utilities ...................................................................................
Restoring the preinstalled software from the Product Recovery CD-ROM ....................................................... 3-12 Chapter 4 Operating Basics Pointing devices ................................................................................ 4-1 Using the Touch Pad .......................................................................... 4-1 Using the USB diskette drive ............................................................ 4-2 Connecting 3 1/2" diskette drive ..........................
Chapter 5 The Keyboard Typewriter keys ................................................................................. 5-1 F1 … F12 function keys ..................................................................... 5-2 Soft keys: Fn key combinations ........................................................ 5-2 Emulating keys on enhanced keyboard .............................................. 5-2 Hot keys .............................................................................................
Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7-1 Accessing HW Setup ......................................................................... 7-1 HW Setup window .............................................................................. 7-1 Supervisor password ....................................................................... 7-10 Chapter 8 Optional Devices PC cards ............................................
CD-RW/DVD-ROM drive ................................................................... 9-14 DVD-R/-RW drive .............................................................................. 9-16 Diskette drive .................................................................................... 9-18 PC card ............................................................................................ 9-18 Pointing device ................................................................................. 9-19 USB .
Appendix I Parts Numbers ....................................................................................
xxx
Preface Congratulations on your purchase of the Satellite A10 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A10 series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB diskette drive, optical media drives, modem, wireless communication features, LAN. It also provides tips on care of the computer, diskettes and CD/ DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes.
Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
xxxiv
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: 1. use of certain external peripheral products 2. use of battery power instead of AC power 3. use of certain multimedia games or videos with special effects 4. use of standard telephone lines or low speed network connections 5. use of complex modeling software, such as high end computer aided design applications 6.
Introduction Equipment checklist .......................................................................... 1-1 Hardware ............................................................................................ 1-1 Software ............................................................................................. 1-1 Documentation ................................................................................... 1-2 Features ............................................................................
INTRODUCTION
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
INTRODUCTION User's Manual • Online manual ❑ Product Recovery CD-ROM Documentation • • • • Satellite A10 Series Portable Personal Computer User's Manual Microsoft Windows XP manual package Instruction Manual for Safety & Comfort End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.
Features Slots 128, 256 or 512 MB memory modules can be installed in the two memory slots for a maximum of 1 GB system memory. Video RAM Allocated a part of System Memory dynamically. (Limit of graphics memory is 32MB at 128MB of System Memory, Limit of Graphics memory is 64MB at more than 256MB of System Memory) Battery pack The computer is powered by one rechargeable lithium-ion battery pack.
INTRODUCTION User's Manual DVD-ROM drive • CD-ROM Mode 1, Mode 2 • CD-ROM XA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CDROMs at maximum 24 speed.
Features Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CDRW at up to 10 speed, DVD-R and DVD-RW at single speed. This drive supports the same formats as the DVDROM drive.
INTRODUCTION User's Manual Pointing device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).Note that some models are not equipped with this port. External monitor 15-pin, analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB2.
Special features Modem LAN Wireless LAN An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada. Only V.90 is available in other regions.
INTRODUCTION User's Manual Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Display automatic power off This feature automatically cuts off power to the internal display when there is no input from the keyboard or pointing device for a time specified. Power is restored when any key is pressed or when there is input from a pointing device.
Utilities This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver. Panel power off/on This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the System Power Mode window in TOSHIBA Power Saver.
INTRODUCTION User's Manual HW Setup TOSHIBA Console This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, click the Windows Start button and click Control Panel. In the Control Panel, select the TOSHIBA HW Setup icon. TOSHIBA Console is a graphical user interface that provides access to help and services.
Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion Battery pack A 128, 256 or 512 MB memory module (PC2100, DDR) can easily be installed in the computer. An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.
INTRODUCTION User's Manual 1-12
Chapter 2 The Grand Tour THE GRAND TOUR Front with the display closed ........................................................... 2-1 Left side .............................................................................................. 2-2 Right side ........................................................................................... 2-3 Back side ............................................................................................ 2-4 Underside ...........................................
THE GRAND TOUR
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. VOLUME CONTROL SYSTEM INDICATORS DISPLAY LATCH WIRELESS COMMUNICATION WIRELESS COMMUNICATION INDICATOR SWITCH Figure 2-1 Front of the computer with display closed Volume control System indicators Display latch Use this dial to adjust the volume of the stereo speakers or the stereo headphones. LEDs let you monitor the status of various computer functions.
User's Manual THE GRAND TOUR Wireless communication switch Slide this switch toward the left of the computer to turn off Wireless LAN function. Slide it toward the right of the computer to turn on the functions (Wireless LAN model or Wireless LAN ready model only). CAUTION: Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off.
Right side Headphone jack PC card slot CB This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automatically disabled. CAUTION: Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. Right side Figure 2-3 shows the computer’s right side.
User's Manual DVD-R/-RW drive THE GRAND TOUR Modem jack Some models are equipped with a full-size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run CD/DVDs without using an adaptor.You can also write CD/DVDs. In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. CAUTIONS: 1.
Back side Link indicator (green) This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly. Parallel port Some models are equipped with a Centronics-compatible, 25-pin parallel port that is used to connect a parallel printer or other parallel device.This port supports Extended Capabilities Port (ECP) standard. TV out port Universal Serial Bus (USB 2.0) ports This 15-pin port lets you connect an external video display.
User's Manual Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. BATTERY SAFETY LOCK BATTERY PACK THE GRAND TOUR BATTERY RELEASE LATCH MEMORY MODULE COVER Figure 2-5 The underside of the computer Battery release latch Slide this latch to release the battery pack for removal. For detailed information on removing the battery packs,refer to Chapter 6, Power and Power-Up Modes.
Front with the display open Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle.
User's Manual The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Power button Press the power button to turn the computer’s power on and off. THE GRAND TOUR Stereo speakers Touch Pad A Touch Pad located slightly in the left from the center of the palm rest is used to control the on-screen pointer. Refer to the Using the Touch Pad section in Chapter 4, Operating Basics.
keyboard indicators CD-ROM drive This indicator glows green when the computer is accessing a diskette in the diskette drive or a disk in the CD-ROM,DVD-ROM, DVD-R/-RW or CD-RW/DVD-ROM drive. Keyboard indicators When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
User's Manual Arrow mode THE GRAND TOUR Numeric mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard. USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes.
Fixed optical media drive NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating. 2. Do not set anything on top of the diskette drive. Fixed optical media drive Some models are equipped with a full-size,CD-ROM drive. ROM drive module that lets you run CD without using an adaptor. It reads CD-ROMs at maximum 24 speed. This drive supports the following formats.
User's Manual DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly. Code Region THE GRAND TOUR 1. Canada, United States 2. Japan, Europe, South Africa, Middle East 3. Southeast Asia, East Asia 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6.
Fixed optical media drive Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East 3. Southeast Asia, East Asia 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6. China DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
User's Manual 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia THE GRAND TOUR 6. China Universal AC adaptor The universal AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region.
Chapter 3 Getting Started GETTING STARTED Setting up your work space .............................................................. 3-1 General conditions .............................................................................. 3-2 Placement of the computer ................................................................. 3-2 Seating and posture ........................................................................... 3-3 Lighting ..................................................................
GETTING STARTED
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User's Manual General conditions GETTING STARTED In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ❑ The temperature should be 5 C to 35 C (41 F to 95 F) and the relative humidity should be 20 to 80 percent.
Setting up your work space Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. BELOW EYE LEVEL GETTING STARTED FOOT REST 90O ANGLES Figure 3-1 Posture and positioning of the computer ❑ Place your chair so that the keyboard is at or slightly below the level of your elbow.
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright light that could shine directly in your eyes. ❑ If possible, use soft, indirect lighting in your computer work area.
Connecting the universal AC adaptor Connecting the universal AC adaptor Attach the universal AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The universal AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz.
User's Manual Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. Lift the panel up and adjust it to the best viewing angle for you. GETTING STARTED CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Starting up for the first time 2. Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully. NOTE: Be sure to read the License Agreement carefully.
User's Manual 3. Click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off. 4. Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored.
Turning off the power Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4. See Chapter 5, Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click start . 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. Hibernate is not displayed. 4. Press the Shift key. The Standby item will change to Hibernate. 5. Select the Hibernate. Automatic Hibernation 1. Open the Control Panel. 2.
User's Manual CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off.
Turning off the power ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ❑ You can use the panel power off feature. Executing standby NOTE: You can also enable Standby by pressing Fn + F3. See Chapter 5, Keyboard, for details. You can enter standby mode in one of three ways: 1. Click start, click Turn Off Computer and click Standby. 2. Close the display panel. This feature must be enabled.
User's Manual Restarting the computer Certain conditions require that you reset the system. For example, if: ❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard commands. There are three ways to reset the computer system: 1. Click start then click Turn Off Computer. From the Turn Off Computer menu select Restart. GETTING STARTED 2. Press Ctrl + Alt + Del to display the Windows Task Manager, then select Shutdown and Restart. 3.
Chapter 4 Operating Basics OPERATING BASICS Pointing devices ................................................................................ 4-1 Using the Touch Pad .......................................................................... 4-1 Using the USB diskette drive ............................................................ 4-2 Connecting 3 1/2" diskette drive ......................................................... 4-2 Disconnecting 3 1/2" diskette drive .......................................
OPERATING BASICS Moving the computer ...................................................................... 4-23 Heat dispersal ..................................................................................
Chapter 4 Operating Basics This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Pointing devices The computer is equipped with a Touch Pad as a pointing device.
User's Manual Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44megabyte or 720-kilobyte diskettes. Refer to Chapter 2, Grand Tour, for more information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-2.
Using optical media drives Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Click the Safety Remove Hardware icon on the Task Bar. 3. Click Diskette drive. 4.
User's Manual Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. EJECT BUTTON Figure 4-3 Pressing the DVD-ROM eject button OPERATING BASICS b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off.
Using optical media drives 2. Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. OPERATING BASICS Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6.
User's Manual CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the drawer to close it. Press gently until it locks into place.
Writing CDs on CD-RW/DVD-ROM drive CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and cause injury. 2. The CD/DVD extends slightly over the sides of the drawer so you can grasp it. Hold the CD/DVD gently and lift it out. 3. Push the center of the drawer to close it.
User's Manual Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Writing CD/DVDs on DVD-R/-RW drive ❑ Do not perform any of the following actions: • Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. • Start a communication application such as a modem. • Apply impact or vibration to the PC. • Install, remove or connect external devices, including the following: PC card, USB devices, external display, optical digital devices. • Use the CD/MP3 control buttons to reproduce music and voice.
User's Manual ❑ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents. ❑ Damage that may be caused by using third party equipment or software.
Writing CD/DVDs on DVD-R/-RW drive Read/write function chart Disc type Read Write Drag’n Drop CD*1 CD-R Yes Yes Yes CD-RW Yes Yes Yes DVD-R Yes Yes Yes DVD-RW Yes Yes Yes DVD-RAM Yes No No DVD+R No No No DVD+RW No No No OPERATING BASICS *1 Software supplied with the product can be used for writing to a disc.
User's Manual ❑ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Writing CD/DVDs on DVD-R/-RW drive ❑ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data. Before writing or rewriting Please observe the following points when you write or rewrite data. Be sure to connect the universal AC adaptor before you write or rewrite. ❑ Be sure to close all other software programs except the writing software.
User's Manual ❑ Make sure writing or rewriting is completed before going into standby/ hibernation. ❑ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand. ❑ Keep mobile phones and other wireless communication devices away from the computer. Drag’n Drop CD+DVD OPERATING BASICS Note the following limitations when you use Drag'n Drop CD+DVD: ❑ DVD-Video cannot be created using Drag'n Drop CD+DVD.
Media care Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
User's Manual 6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. NOTE: The internal modem does not support voice functions. All data and fax functions are supported. CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2.
Modem 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4. Select a region from the region menu or a telephony location from the submenu. • When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically.
User's Manual Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Wireless communications Figure 4-11 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1. Modem speed is slow or communication is interrupted. 2. Skips may occur in sound. OPERATING BASICS Disconnecting To disconnect the internal modem cable, follow the steps below. 1.
User's Manual ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A, Revision A/B combo type) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1Mbit/s. (Revision B) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 108, 96.72, 48, 36, 24, 18 and 12Mbit/s. (Turbo Mode, Revision A/B combo type) ❑ Frequency Channel Selection (Revision A/Turbo Mode:5GHz, Revision B: 2.
LAN Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application. If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN.
User's Manual Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable. You cannot use a CAT3 cable.
Cleaning the computer CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer.
User's Manual ❑ Close all port covers. ❑ Use the carrying case when transporting the computer. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed.
Chapter 5 The Keyboard Typewriter keys ................................................................................. 5-1 F1 … F12 function keys ..................................................................... 5-2 Soft keys: Fn key combinations ........................................................ 5-2 Emulating keys on enhanced keyboard .............................................. 5-2 Hot keys .............................................................................................
THE KEYBOARD
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad.
Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future.
User's Manual LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver. NOTE: Display clarity increases with the brightness level. Wireless setting: Fn + F8 hotkeys are not used.
Windows special keys Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA Utilities and click Accessibility. Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the start menu and the other has the same function as the secondary mouse button.
User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay THE KEYBOARD Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
Generating ASCII characters Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
THE KEYBOARD User's Manual 5-10
Power and Power-Up Modes Power conditions ............................................................................... 6-1 Power indicators ............................................................................... 6-2 Battery indicators ............................................................................... 6-2 DC IN indicator ................................................................................... 6-3 Power indicator ..............................................................
POWER AND POWER-UP MODES
Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions continued Power on AC Battery • Operates adaptor charge is • LED: Battery off not above low connected battery Power off (no operation) DC IN off trigger point Battery • Operates charge is • LED: Battery below low flashes orange battery DC IN off trigger point Battery Computer goes charge is into resume mode exhausted shuts down No • Cannot operate battery • LED: Battery off installed DC IN off Power indicators
Battery types Under any other conditions, the indicator does not light. NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off.
POWER AND POWER-UP MODES User's Manual Battery pack When the universal AC adaptor is not connected, the computer’s main power source is a removable lithium-ion battery, also referred to in this manual as the battery pack. You can purchase additional battery packs for extended use of the computer away from an AC power source. Before you remove the battery pack, set the computer to Hibernation mode or save your data and shut down the computer.
Care and use of the battery pack CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Care and use of the battery pack The battery pack is a vital component of portable computing.
POWER AND POWER-UP MODES User's Manual 3. Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury. To avoid accidental short-circuit, always wrap the battery pack in plastic and cover the terminals with electrical tape when storing or disposing of the battery pack. 4. Never puncture the battery pack with a nail or other sharp object. Never strike it with a hammer or other object.
Care and use of the battery pack 4. Keep the battery pack out or reach of infants and children. It can cause injury. Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash.
POWER AND POWER-UP MODES User's Manual 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power for an extended period, more than a week, the battery might fail to retain a charge.
Care and use of the battery pack POWER AND POWER-UP MODES Charging time (hours) Battery type Power on Battery pack 3600mAh 3.5 to 9 or longer about 2.6 4400mAh 4 to 11 or longer about 2.6 RTC battery Power off 8 Doesn’t charge NOTE: The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer. If you make heavy use of external devices, for example, the battery might scarcely charge at all during operation.
POWER AND POWER-UP MODES User's Manual Monitoring battery capacity Remaining battery power can be monitored in the Power Save Modes window in Power Saver. NOTES: 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity.
Care and use of the battery pack How much charge the battery contained to begin with. ❑ How you use optional devices, such as a PC card, to which the battery supplies power. ❑ Enabling Standby mode conserves battery power if you are frequently turning the computer off and on. ❑ Where you store your programs and data. ❑ Closing the display when you are not using the keyboard saves power. ❑ Operating time decreases at low temperatures. ❑ The condition of the battery terminals.
POWER AND POWER-UP MODES User's Manual 4. Connect the universal AC adaptor to the computer and the power cord to a power outlet. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged. If the DC IN indicator does not glow, power is not being supplied. Check the connections for the universal AC adaptor and power cord. 5. Charge the battery pack until the Battery indicator glows green.
Replacing the battery pack 4. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4. Turn the computer upside down. 5.
POWER AND POWER-UP MODES User's Manual CAUTIONS: 1. The battery pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 2. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch. 1. Turn the computer’s power off. 2.
Power-up modes To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter. NOTE: If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry.
POWER AND POWER-UP MODES User's Manual Panel power off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. NOTE: If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed. System Auto Off This feature turns the system off automatically if it is not used for a set duration.
Chapter 7 HW Setup and Passwords HW SETUP HW Setup ........................................................................................... 7-1 Accessing HW Setup ......................................................................... 7-1 HW Setup window .............................................................................. 7-1 Supervisor password .......................................................................
HW SETUP
Chapter 7 HW Setup and Passwords HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Some models are not equipped with Parallel/Printer tab and/or CPU tab.
User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Setup HW SETUP AND PASSWORDS This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered Change or remove the password. (Default) Set the password.
HW Setup 4. If character strings match, the password is registered and the display changes to: The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! HW SETUP AND PASSWORDS To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks.
User's Manual Key FD After you set a password, you can create a Key FD (diskette). If you forget the user password, the Key FD lets you bypass the password function. HW SETUP AND PASSWORDS NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost. To create a Key FD follow the steps below. 1. Turn off the computer’s power. 2. Connect the diskette drive to a USB port on the computer. 3.
HW Setup Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Standard Bi-directional Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) This setting should be used with some other parallel devices.
User's Manual Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically HW SETUP AND PASSWORDS Switchable Always High Always Low CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at its fastest speed.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD, Network (LAN), PC (ATA) card boot. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2.
User's Manual HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. HW SETUP AND PASSWORDS Built-in HDD −> PC Card (Default) HDDs are searched for a boot command in the following order: the built-in HDD, and the PC card. (Default) PC Card −> Built-in HDD HDDs are searched for a boot command in the following order: the built-in HDD and the PC card.
HW Setup USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enables the USB KB/Mouse Legacy Emulation. (Default) Disables the USB KB/Mouse Legacy Emulation. USB-FDD Legacy Emulation Use this option to enable or disable USB-FDD Legacy Emulation. Enabled Disabled Enables the USB-FDD Legacy Emulation.
User's Manual Supervisor password HW SETUP AND PASSWORDS Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file.
Chapter 8 Optional Devices OPTIONAL DEVICES PC cards ............................................................................................. 8-2 Inserting a PC card ............................................................................. 8-2 Removing a PC card ........................................................................... 8-3 Memory expansion ............................................................................ 8-4 Installing memory module ..................................
OPTIONAL DEVICES
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
User's Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5. Pinch the PC card and remove it.
User's Manual Memory expansion You can install additional memory in the computer’s memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. CAUTION: 1. Use only memory modules approved by TOSHIBA. OPTIONAL DEVICES 2. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. ❑ The computer is turned on.
Memory expansion 6. Lift one side of the insulator sheet and fit the module’s connectors into the computer’s connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. NOTE: You can install the main memory module in either slot. 7. Push the module down so it lies flat. Latches on either side will click into place to secure the module.
User's Manual SLOT B SLOT A Figure 8-4 Installing the memory module OPTIONAL DEVICES 8. Seat the cover and secure it with a screw. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes. 10. Turn the power on and make sure the added memory is recognized. Open System Properties in the Control Panel and click the General tab. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1.
Battery pack OPTIONAL DEVICES Figure 8-5 Removing the memory module 6. Seat the cover and secure it with a screw and replace the battery pack. Battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.
User's Manual External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor’s power on. 4. Turn the computer on. OPTIONAL DEVICES When you turn on the power, the computer automatically recognizes the monitor and determines whether it is color or monochrome.
TV e. Select Television icon. f. Select the Video Standard list box and select the format that your TV supports. *Please select one of them, NTSC-M, NTSC-J or PAL-B from the Video Standard list box though there are lots of selections. Changing the resolution to 640x480 for TV If you want to change the resolution into 640x480 because it is difficulty to read character on TV, follow the steps below. (1) Open Display properties and select the Settings tab. (2) Select Advanced (Figure 8-6).
OPTIONAL DEVICES User's Manual Figure 8-7 The Adapter window (4) Select a resolution from the menu.
Security lock Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the back side of the computer.
OPTIONAL DEVICES User's Manual 8-12
Chapter 9 Troubleshooting TROUBLESHOOTING Problem solving process ................................................................... 9-1 Preliminary checklist .......................................................................... 9-1 Analyzing the problem ........................................................................ 9-2 Hardware and system checklist ........................................................ 9-3 System start-up ................................................................
TROUBLESHOOTING
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically shut down. Problem Procedure Computer shuts down and DC IN indicator flashes orange Leave the computer off until the computer reaches room temperature, then turn it back on. If the computer is still too warm, the DC IN indicator will continue blinking when you turn on the power. Let it cool longer and try again.
User's Manual Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicator and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power the computer The battery may be discharged. Connect the universal AC adaptor to charge the battery. Battery doesn’t charge when the universal AC adaptor is attached (Battery indicator does not glow orange.
Hardware and system checklist Password Problem Procedure Cannot enter or forgot password Contact your dealer. NOTE: For information on setting a password, refer to Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.
User's Manual • The way to replace the key-top Press the key-top until you hear a click after removing a metal spring from the key-top, hooking it to projecting parts and aligning the center of the key-top.
Hardware and system checklist • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top. 2. Attach the plastic spring to the key board with its flat face downward after confirming the direction.
User's Manual 3. Press from the upside until you hear a click after replacing the key-top to the right position. TROUBLESHOOTING LCD panel Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the LCD. They might have come from contact with the keyboard, Touch Pad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner. Be sure to let the LCD dry before closing it.
Hardware and system checklist Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive or a CD-ROM is in the optical media drive. Remove any diskette and/or CD-ROM and check Boot priority. Refer to Chapter 7, Boot Priority. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk.
User's Manual A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs.
Hardware and system checklist DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
User's Manual Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. If problems persist, contact your dealer.
Hardware and system checklist Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
User's Manual Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording. • Do not run or start other software during writing. • Do not jar the computer during writing. • Do not connect/ disconnect external devices or install/remove internal cards during writing. If problems persist, contact your dealer.
Hardware and system checklist Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
User's Manual Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. You cannot access the external 3 1/2" diskette drive Try another diskette. If you can access the diskette, the original diskette (not the drive) is probably causing the problem. If problems persist, contact your dealer.
Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
User's Manual USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. TROUBLESHOOTING 3.
Hardware and system checklist USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If problems persist, contact your dealer. Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules.
User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor TROUBLESHOOTING Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on.
Hardware and system checklist Modem Refer to the online help files for Appendix C and D. Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Properties in the Control Panel. You can hear a dial tone but can’t make a call If the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled. You can also use the ATX command.
User's Manual Character display becomes garbled during a communication In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. Refer to the online help files for Appendix D, S-registers. If problems persist, contact your dealer.
Hardware and system checklist Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on. If problems persist, contact your LAN administrator or dealer.
User's Manual TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ❑ Review troubleshooting sections in the documentation for software and peripheral devices.
TOSHIBA support UnitedKingdom TOSHIBA Information Systems (U.K.) Ltd. TOSHIBA Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany TROUBLESHOOTING United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA InEurope Germany & Austria TOSHIBA Europe (I.E.
TROUBLESHOOTING User's Manual 9-28
Appendix A Specifications ........................................................................... A-1 Appendix B Display Controller and Modes .............................................. B-1 Appendix C AT Commands .......................................................................... C-1 Appendix D S-registers ................................................................................. D-1 Appendix E V.90 ........................................................................................
APPENDIXES
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size Weight 332 (w) x 293 (d) x 33/40 (h) millimeters (not including parts that extend beyond the main body) 2.9 kilograms, configured with: 15"XGA-TFT, CD-RW/ DVD-ROM drive, Modem, Wireless LAN Weight will vary with other configurations.
APPENDIX A User's Manual Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) Communication speed Transmitting level V.17/V.29/V.27ter /V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors. The 15.0" TFT LCD panel displays up to 1024 horizontal and 768 vertical pixels and 1400 horizontal and 1050 vertical pixels.
User's Manual Video modes APPENDIX B The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Appendix B Table1 Video modes (VGA) continued Type Resolution Character LCD matrix colors (pels) CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 x 200 Pels 8x8 16 of 256K 16 of 256K 70 E VGA Grph 640 x 200 Pels 8x8 16 of 256K 16 of 256K 70 F VGA Grph 640 x 350 Pels 8 x 14 Mono Mono 70 10 VGA Grph 640 x 350 Pels 8 x 14 16 of 256K 16 of 256K 70 11 VGA Grph VGA Grph 640 x 480 Pels 640 x 480 Pels 8 x 16 2 of 256K 2 of 256K 60 8 x 16 16 of 256K 16 of 256K 60
User's Manual APPENDIX B Table 2 Video modes (XGA) Resolution LCD colors CRT colors 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K (Virtual) 256/256K 60 75 85 100 1400 x 1050 256/256K (Virtual) 256/256K 60 75 85 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 1920 x 1440 256/256K (Virtual) 256/256K 60 B-4 Vertical frequency (Hz)
Appendix B Table 2 Video modes (XGA) continued LCD colors CRT colors Vertical frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1400 x 1050 64K/64K (Virtual) 64K/64K 60 75 85 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 1920 x 1440 64K/64K (Virtual) 64K/64K 60 APPENDIX B Resolution B-5
User's Manual APPENDIX B Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1400 x 1050 16M/16M (Virtual) 16M/16M 60 75 85 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 1920 x 1440 16M/16M (Virtual) 16M/16M 60 B-6 Vertical frequency (Hz)
Appendix B Table 3 Video modes (Super XGA+) LCD colors CRT colors Vertical frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K 256/256K 60 75 85 100 1400 x 1050 256/256K 256/256K 60 75 85 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 1920 x 1440 256/256K (Virtual) 256/256K 60 APPENDIX B Resolution B-7
User's Manual APPENDIX B Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K 64K/64K 60 75 85 100 1400 x 1050 64K/64K 64K/64K 60 75 85 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 1920 x 1440 64K/64K (Virtual) 64K/64K 60 B-8 Vertical frequency (Hz)
Appendix B Table 3 Video modes (Super XGA+) continued LCD colors CRT colors Vertical frequency (Hz) 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M 16M/16M 60 75 85 100 1400 x 1050 16M/16M 16M/16M 60 75 85 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 1920 x 1440 16M/16M (Virtual) 16M/16M 60 APPENDIX B Resolution B-9
APPENDIX B User's Manual B-10
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn Any command issued is acknowledged with a response in either text or numeric values known as result codes.
User's Manual A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
Appendix C En ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. E0 Disables echo to the computer.
User's Manual Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode APPENDIX C This command turns the speaker on or off. M0 The speaker is off. M1 The speaker is on until the modem detects the carrier signal (default). M2 The speaker is always on when modem is off-hook.
Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Result Codes: OK n=0,1,3 P Select pulse dialing This command configures the modem for pulse (non touch-tone) dialing.
User's Manual T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
Appendix C X5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT , RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. APPENDIX C Busy tone detect Disabled: The modem ignores any busy tones it receives.
User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise &Dn DTR control APPENDIX C This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard tone to 550 Hz. &G2 Sets guard tone to 1800 Hz. Result Codes: OK n=0,1,2 ERROR Otherwise &Kn Local flow control selection Disable flow control.
User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result Codes: APPENDIX C &V OK n=0 CONNECT n=1 ERROR Otherwise Display Current Configuration This command displays the current configuration of the modem.
Appendix C \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode. \N3 V.42, MNP, or buffered (default). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode.
User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: OK n=0,1 ERROR Otherwise %B View numbers in blacklist APPENDIX C If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: S1 rings Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: S5 ASCII Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only.
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.
Appendix D S37 Dial line rate maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps APPENDIX D S37 = 0 (default) D-5
User's Manual AT command set result codes The following table shows the result codes.
Appendix D Result Code Numeric Description DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLIST FULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
APPENDIX D User's Manual D-8
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. NOTE: V.
User's Manual APPENDIX E Table E-1 Result codes for a V.90 connection No.
Appendix E *EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V42 NoEC V.42 error control and V.42bis data compression V.42 error control only No error control protocol AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX E User's Manual E-4
Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for information only. To install the internal modem follow the procedures below. Installing the modem board and jack To install the modem board and jack, follow the steps below. 1.
APPENDIX F User's Manual 9. Secure the cover with one screw. Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the modem cover. 5. Remove the modem cover. 6. Remove two screws and remove the modem board. 7. Disconnect the modem cable. 8. Secure the modem cover with one screw. 9.
Appendix G Wireless LAN Form Factor Capability Network Operating System Media Access Protocol Data Rate - Mini PCI TypeIII - I EEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance. - Microsoft Windows® Networking - CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) - 54/48/36/24/18/12/9/6 Mb/s (Revision A) - 11/5.
User's Manual - Band2.4GHz (2400-2483.5 MHz) (Revision B) Modulation Technique - DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) - OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM64QAM (Revision A, Turbo Mode) APPENDIX G The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at lower Transmit range may travel larger distances. ❑ The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
Appendix G When installing Wireless LAN Cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850MHz Note 42 5210 US only *1 50 5250 US only *1 58 5290 US only *1 152 5760 US only *1 160 5800 US only *1 APPENDIX G Channel ID *1: Available Area: US (USA, CANADA) only G-4
Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual APPENDIX H The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, and communication devices.
User’s Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice. Celeron 1.80 Celeron 2.00 Celeron 2.20 Pentium4 1.8-M Pentium4 1.9-M Pentium4 2.0-M Pentium4 2.2-M C1.80 C2.00 C2.20 P4-1.8 P4-1.9 P4-2.0 P4-2.
The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
GLOSSARY Adaptor (Abbreviations continued) TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus UXGA: ultra extended graphics array VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology XGA: extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
cache memory backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right-most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on. For example, the binary number 101 has a value of 5.
GLOSSARY capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable.
dielete computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration. CRT: Cathode Ray Tube.
GLOSSARY device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk.
hard disk drive (HDD) execute: To interpret and execute an instruction. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support.
GLOSSARY hardware computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer.
menu K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key.
GLOSSARY microprocessor mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/ demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
prompt parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.
GLOSSARY Radio frequency interference (RFI) shield interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations.
write protection U synchronous: Having a constant time interval between successive bits, characters or events. V system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk. Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
GLOSSARY Glossary Glossary-14
Index Index A AC adaptor, See Universal AC adaptor ASCII characters 5-9 Battery automatic hibernation 1-8 charging 6-8 extending life 6-11 indicator 2-8, 6-2 location 2-6 monitoring capacity 6-10 real time clock 1-3, 6-4 safety precautions 6-5 save mode 1-9 types 6-3 Battery charger 1-11 Battery pack 1-3, 2-6 additional 1-11, 8-7 replacing 6-12 Boot mode 3-7 Boot priority 7-6 C Cache memory 1-2 CD-ROM drive 1-3, 2-11 location 2-3 problems 9-11 using 4-3 CD-RW/DVD-ROM drive 1-4, 2-12 location 2-3 problems
User's manual work habits 3-4 Expansion memory, See Memory INDEX F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 (display brightness) 5-6 Fn + F8 (wireless setting) 5-6 Fn + F9 (Touch Pad) 5-6 Fn + F10 (arrow mode) 5-3 Fn + F11 (numeric mode) 5-3 Fn + F12 (ScrLock) 5-3 Fn-esse 1-10 Funct
Index P LAN 1-7 connecting 4-22 disconnecting 4-22 jack 2-5 LAN active indicator 2-4 link indicator 2-5 problems 9-24 LCD, See Display, Video modes and Monitor external Level 2 cache, See Cache memory Lock security, See Security lock Panel power off, See Power Password Key FD 7-4 power on 1-8 problems 9-7 starting the computer by 6-15 supervisor 7-10 user 7-2 PC card 1-6 installing/removing 8-2,8-3 location of slot 2-2 problems 9-18 Pointing device, See Touch Pad Ports external monitor 1-6 USB 1-6 Power
INDEX User's manual keyboard 9-7 LAN 9-24 LCD panel 9-10 memory expansion 9-21 modem 9-23 monitor external 9-22 mouse, USB 9-20 overheating power down 9-5 password 9-7 PC card 9-18 pointing device 9-19 power 9-4 real time clock 9-25 self test 9-4 sound system 9-22 support from TOSHIBA 9-26 system start-up 9-3 Touch Pad 9-19 USB 9-21 Wireless LAN 9-25 Processor 1-2 volume control 2-1 Standby 1-9 automatic 1-8 setting 3-10 System indicators, See indicators R Universal AC adaptor 1-3, 2-14 additional 1-11,
Index Wireless LAN 1-7 problems 9-25 using 4-19 INDEX Index-5
