OPERATING INSTRUCTIONS 43/50/55/58/65 UA3D Series 43/50/55/58/65 UA5D Series 43/50/55/58/65 QA5D Series 43/50/55/58/65 QA7D Series
Timeshift Recording ............................................33 Table of Contents Disk Format ........................................................33 Safety Information .................................................2 Schedule List ......................................................33 Markings on the Product........................................2 CEC .......................................................................34 Introduction ....................................................
Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains. The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable.
WARNING Do not ingest the battery, Chemical Burn Hazard This product or the accessories supplied with the product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
Introduction Thank you for choosing our product. You’ll soon be enjoying your new TV. Please read these instructions carefully. They contain important information which will help you get the best from your TV and ensure safe and correct installation and operation. Features • Remote controlled colour TV • AndroidTM operating system intended to achieve, showing the hidden areas of dark shadows and sunlight with full clarity, colour and detail.
Assembling the pedestal 1. Place the pedestal(s) on the mounting pattern(s) on the rear side of the TV. 2. Insert the screws provided and tighten them gently until the pedestal(s) is/are properly fitted. Removing the pedestal from the TV Be sure to remove the pedestal in the following way when using the wall mount bracket or repacking the TV. • Put the TV onto a work table with the screen panel down on a clean and soft cloth. Leave the pedestal(s) protruding over the edge of the surface.
Other Connections If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.
Turning On/Off the TV (**) Connect power IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. consumption. In order to minimise energy consumption switch your TV into standby mode as explained above. Turning On/Off the TV (**) Connect power IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket.
Plug the power cord to the mains socket outlet. The TV will switch on automatically. To switch on the TV from standby If the TV is in standby mode the standby LED lights up. To switch on the TV from standby mode either: • Press the Standby button on the remote control. • Press the control button on the TV. The TV will then switch on. To switch the TV into standby The TV cannot be switched into standby mode via control button. Press and hold the Standby button on the remote control.
TV Control & Operation (**) TV Control & Operation (**) The control switch allows you to control the Programme and Quick Standby-On functions of the TV. The control button allows you to control the Quick Standby-On function of the TV. Note: The position of the control switch may differ depending on the model. Note: The position of the control button may differ depending on the model.
Remote Control 1. 2. 3. 28 27 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Inserting the Batteries into the Remote The remote may have a screw that secures the battery compartment cover onto the remote control (or this may be in a separate bag). Remove the screw, if the cover is screwed on previously. Then remove the battery compartment cover to reveal the battery compartment. Insert two 1.5V - size AAA batteries. Make sure the (+) and (-) signs match (observing correct polarity).
network and press OK if you want to use wireless connection instead of wired connection. Initial Setup Wizard Note: Follow the on-screen instructions to complete the initial setup process. Use the directional buttons and the OK button on the remote to select, set, confirm and proceed. When turned on for the first time, a welcome screen will be displayed. Select your language and press OK. Follow the on-screen instructions to setup your TV and install channels.
OK on the remote to confirm and proceed. You can also view Terms of Service, Privacy Policy and Play Terms of Service on this screen. To display the content an internet connection is needed. A message will be displayed mentioning the web site address on which this information can also be viewed, in case internet access is not available. 10. Google Services Select each to learn more about each service, such as how to turn it on or off later. Data will be used according to Google’s Privacy Policy.
Satellite If Satellite option is selected, Antenna Type screen will be displayed next. If you have a Direct satellite system, you can proceed to the next step quickly by selecting the Next option here. Highlight More and press OK to set the antenna type manually. Single, Tone Burst, DiSEqC and Unicable options are available. Highlight the antenna type that corresponds to your satellite system and press OK or the Right directional button to proceed to the next step.
device. Press the Home button to display Home Screen. You can also select the Android TV Home option from the Inputs menu to switch to Home Screen. To open the Inputs menu, press the Source button on the remote or press the Menu button on the remote when the TV is in Live TV mode, highlight the Source option in the TV options menu, and press OK. Depending on your TV setup and your country selection in the initial setup, the Home menu may contain different items.
or on the TV to turn the screen on again. Note that you can not turn the screen on via the Volume +/-, Mute and Standby buttons. These buttons will function normally. No Signal Auto Power Off: Set the behaviour of the TV, when no signal is detected from the currently set input source. Define a time after which you want your TV to turn itself off or set as Off to disable. Auto Sleep: Define an idle time after which you want your TV to enter sleep mode automatically.
System Information: Display detailed system information on the current channel such as Signal Level, Signal Quality, Frequency, etc. Record Record List: The recordings will be displayed if any available. Highlight a recording of your choice and press the Yellow button to delete it or press the Blue button to view detailed information. You can use Red and Green buttons to scroll the page up and down. Device Info: Connected USB storage devices will be displayed.
Channel Skip: Set channels to be skipped when switching the channels via Programme +/- buttons on the remote. Highlight the desired channel/s on the list and press OK to select/unselect. Channel Swap: Replace the positions of the two selected channels in the channel list. Highlight the desired channels on the list and press OK to select. When the second channel is selected, the position of this channel will be replaced with the position of the first selected channel.
Input Source - Satellite Satellite Re-scan: Start a satellite scan beginning with the antenna selection screen. When this scanning option is preferred, some scanning configurations will not be available and thus the preferences you made during the initial setup process may not be changed. For the General Satellite channel installation mode SatcoDX Scan option may also be available here. Copy the relevant sdx file into the root directory of an USB storage device and connect it to your TV.
The content of this menu may not be displayed if the channel installation is not completed and no channels are installed. more information refer to the Storage section in the Settings>Device Preferences menu. Channels Blocked: Select channel/s to be blocked from the channel list. Highlight a channel and press OK to select/unselect. To watch a blocked channel PIN should be entered first. Highlight the app you want to move and press OK to see available options.
broadcasts. Set corresponding to your environment and preference. Disable by setting as Off if you want to manually change the date or time. Then set date, time, time zone and hour format options. Timer Power On Time Type: Set your TV to turn on by itself. Set this option as On or Once to enable a power on timer to be set, set as Off to disable. If set as Once the TV will turn on only once at the defined time in Auto Power On Time option below.
content histogram in order to provide deeper black and brighter white perception. Set your Adaptive Luma Control preference as Low, Medium, Strong or turn it off by setting as Off. Local Contrast Control: Local contrast control divides each frame to defined small regions and provides ability to apply independent contrast setting for each region. This algorithm improves fine details and provides better contrast perception.
sound options may become unavailable depending on the selection. abnormal sound rises and falls. Turn this feature on/off by pressing OK. Balance: Adjust the left and right volume balance for speakers and headphones. Surround Virtualiser: Turn the surround virtualiser feature on or off. Sound Surround: Turn the surround sound feature on or off. Dolby Atmos: Your TV supports Dolby Atmos technology.
the formatting, you may consider backing up the data on your device to your TV’s internal storage or to another USB storage device using the Back up apps option. Otherwise, some apps may not work properly after formatting. Follow the on-screen instructions and read the information displayed on the screen before proceeding. Note: Formatting the connected storage device will erase all data installed on it. Back up the files that you want to keep before you proceed with formatting the device.
Restart: A confirmation message will be displayed, select Restart to proceed with restarting. The TV will switch off/on first. Select Cancel to exit. Device Preferences About: Check for system updates, change the device name, reset the TV to the factory defaults and display system information such as network addresses, serial numbers, versions, etc.
Sharpness: Adjust the sharpness value for the objects displayed on the screen. Gamma: Set your gamma preference. Dark, Middle and Bright options will be available. Colour Temperature: Set your colour temperature preference. User, Cool, Standard and Warm options will be available. You can adjust red, green and blue gain values manually. If one of these values is changed manually, Colour Temperature option will be changed to User, if not already set as User. Display Mode: Set the aspect ratio of the screen.
to set this function as on or off dynamically, according to source signal type. When set as Off, the TV’s maximum colour capacity is used by default. Colour Tuner: Colour saturation, hue, brightness can be adjustable for red, green, blue, cyan, magenta, yellow and flesh tone (skin tone) for having more vivid or more natural image. Set the HUE, Colour, Brightness, Offset and Gain values manually. Highlight Enable and press OK to turn this function on.
There will also be options for ejecting and setting up the connected USB storage devices as device storage. Eject: To keep your content safe, eject your USB storage device before you unplug it from your TV. Erase & format as device storage: You can use the connected USB storage device to extend the storage capacity of your TV. After doing this, that device will only be usable with the TV. Follow the on-screen instructions and read the information displayed on the screen before proceeding.
Speaker: Turn this option on if you want to hear the audio commentary through the TV speakers. Headphone: Turn this option on if you want to route the sound of the audio commentary to the TV’s headphone output. Volume: Adjust the volume level of the audio commentary. Pan and Fade: Turn this option on if you want to hear the audio commentary more clearly, when it is available through broadcast. Audio for the Visually Impaired: Set the audio type for visually impaired.
Yellow button, then highlight the Move option and press OK. Then use the Up and Down directional buttons to move the channel to the desired position and press OK. In order to delete a channel from the favourite list press the Yellow button, then highlight the Delete option and press OK. Programme Guide By means of Electronic Programme Guide (EPG) function of your TV, you can browse the event schedule of the currently installed channels on your channel list.
Wireless Connection A wireless LAN modem/router is required to connect the TV to the Internet via wireless LAN. Highlight Wi-Fi option in the Network & Internet menu and press OK to enable wireless connection. Available networks will be listed. Select one and press OK to connect. For more information refer to Network & Internet section under the title of Settings. values for the wireless standards. They are not the actual speeds of data transmission.
Parser mode) will be displayed. To set the photo frame image press the Menu button while the photo file of your choice is displayed, highlight Photo Frame Image and press OK. Additionally, you can toggle between browsing modes by pressing the Blue button. List View and Grid View modes are available. While browsing for the video, photo and text files a preview of the highlighted file will be displayed in a small window on the left side of the screen if the browse mode is set to List View.
in the storage device, depending on the viewing style, will be repeatedly played back or displayed. Shuffle On/Off: Turn the shuffle option on or off. Press OK to change the setting. Duration: Set the interval between the slides. Highlight an option and press OK to change the setting. You can also press the Green button to set. This option will not be available if the slide show is paused. Rotate: Rotate the image. The image will be rotated 90 degrees clockwise each time you press OK.
Timeshift Recording USB Recording (**) To record a programme, you should first connect a USB storage device to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature. To record long duration programmes such as movies, it is recommended to use USB Hard disk drives (HDD’s). Recorded programmes are saved onto the connected USB storage device.
dialogue will be displayed on the screen. Highlight Yes and press OK to delete the selected timer. A warning message will be displayed if the time intervals of two timers overlap. You can not set more than one timer for the same time interval. Press EXIT button to close the Schedule List. CEC With CEC function of your TV you can operate a connected device with the TV remote control. This function uses HDMI CEC (Consumer Electronics Control) to communicate with the connected devices.
3. Tap on the ‘Easy projection’ and enable ‘Wireless projection’. Available devices will be listed 4. Select the TV you would like to cast to 1. Slide down the notification panel 2. Tap on ‘Wireless projection’ 3. Select the TV you would like to cast to or If the mobile app is Cast-enabled, such as YouTube, Dailymotion, Netflix, you can cast your app to your TV. On the mobile app, look for the Google Cast icon and tap on it. Available devices will be detected and listed.
No sound / poor sound Troubleshooting & Tips • Make sure that the sound settings are correctly set. TV does not switch on • Make sure that all cables are properly connected. • Make sure the power cord is plugged in securely to the power outlet. • Make sure that the volume is not muted or set to zero, increase the volume to check. • Disconnect the power cord from the power outlet. Wait for one minute then reconnect it.
Supported File Formats for USB Mode Video Decoder Video Codec Resolution Bit Rate VP9 4096x2176@60fps 100Mbps HEVC/H.265 4096x2176@60fps 100Mbps MPEG1/2 1920x1080@60fps 80Mbps MPEG4 1920x1080@60fps 40Mbps Sorenson H.263 1920x1080@60fps 40Mbps H.263 1920x1080@60fps 40Mbps H.
Video Encoder Video Codec H.264 Max Resolution 1920x1080@30fps Max Bit Rate 12Mbps Profile Main profile, level 4.1 Note Hardware video encoder Audio Audio Codec MPEG1/2 Layer1 MPEG1/2 Layer2 MPEG1/2/2.5 Layer3 AC3(DD) EAC3(DDP) Sample rate 16KHz ~ 48KHz 16KHz ~ 48KHz 8KHz ~ 48KHz 32KHz, 44.1KHz, 48KHz 32KHz, 44.1KHz, 48KHz Channel Up to 2 Up to 2 Up to 2 Bit Rate Container Note 32Kbps ~ 448Kbps MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), MKV (.mkv, .mka), 3GPP (.3gpp, .
Audio Codec Sample rate Channel Bit Rate Container Note WMA 10 Pro M1 8KHz ~ 48KHz Up to 5.1 < 384Kbps ASF (.asf), WMV (.wma, .wmv), AVI (.avi), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov) WMA 10 Pro M2 8KHz ~ 96KHz Up to 5.1 < 768Kbps ASF (.asf), WMV (.wma, .wmv), AVI (.avi), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov) VORBIS Up to 48KHz Up to 2 DTS Up to 48KHz Up to 5.1 DTS LBR 12KHz, 22KHz, 24KHz, 44.1KHz, 48KHz Up to 5.
Picture Image Resolution (width x height) Photo Base-line Progressive JPEG 15360 x 8640 1024 x 768 PNG 9600 x 6400 BMP GIF WebP HEIF 9600 x 6400 6400 x 4800 3840 x 2160 4000 x 3000 Subtitle Internal File Extension Container ts, trp, tp TS mp4 MP4 mkv MKV Subtitle Codec DVB Subtitle Teletext CC(EIA608) PGS VobSub PGS TX3G ASS SSA SRT VobSub PGS External File Extension Subtitle Parser .srt SubRip .ssa/.ass SubStation Alpha Advanced SubStation Alpha .smi SAMI .
Supported DVI Resolutions When connecting devices to your TV’s connectors by using a DVI converter cable (DVI to HDMI cable - not supplied), you can refer to the following resolution information.
Licences The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. Dolby, Dolby Vision, Dolby Atmos, and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Manufactured under licence from Dolby Laboratories. Confidential unpublished works. Copyright © 2012-2022 Dolby Laboratories. All rights reserved. content.
Disposal Information The following information is only for EU-member states: Disposal of products The crossed out wheeIed dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
REACH information The European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the presence in our articles of substances included on the candidate list according to REACH regulation. Please consult the following website www.toshiba-tv.