24/32/39/40/43/48/49 L28 Series 32/39/40/43/49 L38 Series 24/28/32 D28 Series 24/28/32 W28 Series 24/28/32 D38 Series 24/28/32 W38 Series OPERATING INSTRUCTIONS
HBBTV System...................................................... 28 Contents Environmental Information....................................... 2 Disposal Information................................................. 2 Standby Notifications................................................ 3 TV Control Switch & Operation................................ 3 Using Main TV Menu................................................ 3 Inserting the Batteries into the Remote.................... 5 Power Connection..........
Environmental Information This television is designed to be environment friendly. To reduce energy consumption, you can follow these steps: If you set the Energy Saving to Minimum, Medium, Maximum or Auto the TV will reduce the energy consumption accordingly. If you like to set the Backlight to a fixed value set as Custom and adjust the Backlight (located under the Energy Saving setting) manually using Left or Right buttons on the remote. Set as Off to turn this setting off.
Standby Notifications If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 3 minutes, it will go into standby. When you next switch-on, the following message will be displayed: “TV switched to stand-by mode automatically because there was no signal for a long time.” Press OK to continue. The Auto TV OFF option(in the Settings>System >More menu) could have been set to a value between 1 and 8 hours by default.
to select the position that you want the item to move to and press OK. 2. TV 2.1. Guide You can access the electronic programme guide menu using this option. Refer to Electronic Programme Guide section for more information. 2.2. Channels You can access the Channels menu using this option. Refer to Using the Channel List section for more information. 2.3. Timers You can set timers for future events using the options of this menu. You can also review the previously created timers under this menu.
Inserting the Batteries into the Remote Remove the back cover to reveal the battery compartment. Insert two size AAA batteries. Make sure the (+) and (-) signs match (observe correct polarity). Do not mix old and new batteries. Replace only with same or equivalent type. Place the cover back on. A message will be displayed on the screen when the batteries are low and must be replaced. Note that when the batteries are low, the performance of the remote control may be impaired.
Remote Control 1. Standby: Switches On / Off the TV 2. Source: Shows available broadcast and content sources 3. Numeric buttons: Switches the channel, enters a number or a letter in the text box on the screen. 4. Language: Switches among sound modes (analogue TV), displays and changes audio/subtitle language and turns subtitles on or off (digital TV, where available) 5. Menu: Displays TV menu 6. Volume +/- 7.
Connections Connector Type Cables Device VGA Connection (back) AUDIO IN PC/YPbPr Audio Connection (back) YPbPr/PC Audio Cable HDMI Connection (side&back) SPDIF SPDIF BACK AV SPDIF (Coaxial Out) Connection (back) (optional) SPDIF (Optical Out) Connection (back) (optional) Back AV (Audio/Video) Connection (back) HEADPHONE Headphone Connection (side) YPBPR YPbPr Video Connection (back) See the illustrations on the left side. You can use YPbPr to VGA cable to enable YPbPr signal via VGA input.
Switching On/Off To Switch the TV On Connect the power cord to a power source such as a wall socket (220-240V AC, 50 Hz). To switch on the TV from standby mode either: • Press the Standby button, Programme +/- or a numeric button on the remote control. • Press the middle of the side function switch on the TV in.
satellite search is performed some settings should be made. A menu will be displayed where you can select to start M7 or Fransat operator installation or a standard installation. To start an M7 operator installation set the Install Type as Operator and the Satellite Operator as the related M7 operator. Then highlight Preferred Scan option and set as Automatic channel scan and press OK to start the automatic search.
Additionally you can download one of the satellite channel table files stored in USB device, to the TV. When you select one of these files, all services and related satellites and transponders in the selected file will be stored in the TV. If there are any installed terrestrial, cable and/or analogue services, they will be kept and only satellite services will be removed. Afterwards, check your antenna settings and make changes if necessary.
Watching Recorded Programmes Select Recordings from the TV menu. Select a recorded item from the list (if previously recorded). Press the OK button to view the Options menu. Select an option then press OK button. Media Browser Settings and Options menus will be available. The contents of these menus may change according to the type of the currently open media file. Only Sound Settings menu will be available while playing back audio files.
devices. UHD (4K, Ultra HD) channels are not supported and both of the devices must be connected to the same network. CEC This function allows to control the CEC-enabled devices, that are connected through HDMI ports by using the remote control of the TV. To close the E-Manual screen press the Exit or Menu button. Note: Depending on model, your TV may not support this function. The contents of the E-Manual may vary according to the model.
Settings Menu Contents Picture Menu Contents You can change the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: Cinema, Game(optional), Sports, Dynamic and Natural. Mode Contrast Adjusts the light and dark values on the screen. Brightness Adjusts the brightness values on the screen. Sharpness Sets the sharpness value for the objects displayed on the screen. Colour Sets the colour value, adjusting the colours.
Sound Menu Contents Volume Adjusts the volume level. Equalizer Selects the equalizer mode. Custom settings can be made only when in User mode. Balance Adjusts whether the sound comes from the left or right speaker. Headphone Sets headphone volume. Please ensure before using headphones that the headphone volume is set to a low level, to prevent damage to your hearing. Sound Mode You can select a sound mode (If the viewed channel supports).
Network Menu Contents Network Type Disable the network connection or change the connection type. Scan Wireless Networks Start a search for wireless networks. This option will be available if the Network Type is set as Wireless Device. Press WPS on your wifi router If your modem/router device has WPS, you can directly connect to it using this option. Highlight this option and press OK. Go to your modem/router device and press the WPS button on it to make the connection.
Fransat Options (optional) Displays Fransat options. Parental Control Displays parental control options. Enter the PIN number you have defined in the initial installation to view current settings. System Information Displays system information. Reception Information Displays current satellite reception information. CAS-Module Displays current CAS module information. Upgrade Displays software upgrade options.
System Menu Contents Conditional Access Controls conditional access modules when available. Language You may set a different language depending on the broadcaster and the country. Privacy Settings (*) Manage your privacy privileges for smart TV related applications. Press OK to enter the menu and set according to your preferences. Parental Enter correct password to change parental settings. You can easily adjust Menu Lock, Maturity Lock, Child Lock or Guidance in this menu.
CEC Auto Power On This function allows the connected HDMI-CEC compatible device to turn on the TV and switch to its input source automatically. Press Left or Right button to enable or disable the feature. Speakers To hear the TV audio from the connected compatible audio device set as Amplifier. You can use the remote control of the TV to control the volume of the audio device. Smart Remote (optional) Press OK to open the Smart Remote menu screen.
Child Lock: If this option is set to On, the TV can only be controlled by the remote control. In this case the control buttons on the TV will not work. General TV Operation Using the Channel List The TV sorts all stored stations in the channel list. You can edit this channel list, set favourites or set active stations to be listed by using the Channels menu options. Press the OK button to open the channel list.
Highlight Extras tab and press OK to access below options. Highlight Genre: Displays Highlight Genre menu. Select a genre and press OK. The events in the programme guide matching the selected genre will be highlighted. Guide Search: Displays searching options. Using these options, you can search the programme guide database in accordance with the selected criteria. Matching results will be listed. Now: Displays current event of the highlighted channel.
No picture • TV is not receiving any signal. Make sure the correct source has been selected. • Is the antenna connected properly? • Is the antenna cable damaged? • Are suitable plugs used to connect the antenna? 8 1024x768 70Hz 9 1024x768 75Hz 10 1152x864 75Hz 11 1280x768 60Hz 12 1360x768 60Hz 13 1280x960 60Hz • If you are in doubt, consult your dealer. 14 1280x1024 60Hz No sound 15 1280x1024 75Hz • Check if the TV sound is muted.
Supported File Formats for USB Mode Video File Formats Extension Video Codec .mpg, .mpeg, .dat, .vob .ts, .trp, .m2ts .avi Max. Resolution & Frame Rate & Bit Rate MPEG1/2, H.264, VC1 MPEG1/2, MPEG4, H.264, MJPEG .mp4, .m4a, .m4v, .mov, .qt, MPEG1/2, H.263, MPEG4, H.264 .3gp, .3g2, .3gpp .mkv MPEG 1/2, MPEG4, H.264 .flv Sorenson Sp, MPEG4, H.264 .ogm, .ogg MPEG1/2, MPEG4 .asf, .wmv MPEG4, WMV3, VC1 .rm, .rmvb RV30, RV40 .webm VP9, VP8 .mp4, .mov, .3gpp, .3gp, MPEG transport stream, .ts,.
Subtitle File Formats External Subtitles Extension Specification .ssa SubStation Alpha .ass Advanced SubStation Alpha .srt Subripper .sub Micro DVD / SubViewer .sub + .idx VOBSub .txt Micro DVD / TMPlayer / MPL2 .mpl MPL2 .smi Sami .jss JACOSUB .ttml TTML .txt / .sub DVDSUBTITLE .lrc - Internal Subtitles Extension Specification .mkv VOBSub .mkv ASS / SSA / TEXT .dat, .mpg, .mpeg, .vob DVD Subtitle .
Internet Speed Test Connectivity Highlight Internet Speed Test and press the OK button. TV will check the internet connection bandwidth and display the result when complete. Wired Connectivity To Connect to a Wired Network • You must have a modem/router connected to an active broadband connection. • Connect your TV to your modem/router via an Ethernet cable. There is a LAN port at the rear (back) of your TV. 1 Advanced Settings Highlight Advanced Settings and press the OK button.
• The Wireless feature of the TV supports 802.11 a,b,g & n type modems. It is highly recommended that you should use the IEEE 802.11n communication protocol in order to avoid any possible problems while watching videos. • You must change your modem’s SSID when there are any other modems around with the same SSID. You can encounter connection problems otherwise. Use a wired connection if you experience problems with a wireless connection.
Plug the wireless USB dongle to TV first, if the TV doesn’t have internal WLAN feature. image transfer or audio streaming to the TV will not be possible. Then press the Source button on the remote and switch to Wireless Display source. The images sent by mobile device will be displayed on the TV without confirmation request, if the image file is suitable. You can also save the image file to a connected USB memory drive or set as boot logo, if this feature is supported and the file is suitable.
other WLAN compatible devices. Try changing the active channel on the WLAN router. Internet Connection Not Available / Audio Video Sharing Not Working and press OK to continue. The media browser will then be displayed. Refer to the Media Browser menu section for further information on file playback. If the MAC address (a unique identifier number) of your PC or modem has been permanently registered, it is possible that your TV might not connect to the internet.
button, the address/search bar, the Speed Dial and the Vewd buttons are available. To add a desired website to the Speed Dial list for quick access, move the cursor to the top of the page or press the Back/Return button. The browser bar button and will appear. Highlight the Speed Dial press the OK button. Then select Add to Speed Dial option and press the OK button. Fill in the blanks for Name and Address, highlight OK and press the OK button to add.
Install the Smart Center application onto your mobile device. Start the Smart Center application. If all connections are configured properly, you will see your TV’s name on your mobile device. If your TV’s name doesn’t appear on the list, wait a while and tap on the Refresh widget. Select your TV from the list. Mobile Device screen On the main screen you can find tabs to access various features.
Choose channel list source: You can choose the channel list source to be used in the application. The options are “TV List” and “Custom List”. Additionally you can activate “Remember my choice” option to set the selected channel list source as a constant choice. In this case if the selected source is available it will be used in the application. Version No: Displays the current version of the application. Detail Page To open detail page tap on a programme.
Example Commands Alexa Ready Feature (optional) Alexa is Amazon’s cloud-based voice service available on many voice controlled assistant devices. Your TV is compatible with and ready to be utilized with Alexa devices. With this feature you can use your voice to control functions on your TV, such as turning on or off, changing channel or input source, controlling volume, and more.
DVD Mode (optional) Safety Information CAUTION DVD Player is a class 1 laser product. However this product uses a visible laser beam which could cause hazardous radiation exposure. Be sure to operate the player correctly as instructed. CLASS 1 LASER PRODUCT • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs.
3. Press Down / Up / Left / Right or the numeric button (s) to select the preferred title. 4. Press OK to confirm the selected item. The played item may be a motion picture, a still picture or another submenu depending on the disc content. For your reference If an action corresponding to a button is prohibited the ” symbol appears. “ Notes on Playback 1. No sound will be heard during fast forward or rewind. 2. No sound will be heard during slow motion play. 3.
Disc Types Compatible with This Unit Disc Types (Logos) DVD Recording Disc Types Size Single- Audio + Max. Playing Characteristics Time 12 cm Video sided; 240 min. Doublesided; 480 min. AUDIO-CD Audio MP3-CD Audio (xxxx.mp3) PICTURE-CD Video (still picture) 12 cm 74 min. It depends 12 cm on MP3 quality. It depends 12 cm on JPEG quality. • DVD contains excellent sound and video due to Dolby Digital and MPEG-2 System.
Overview of the Remote Controll (If DVD is available) 20 19 1. Standby 2. Source selection 3. Numeric buttons 4. Audio language selection 5. TV Menu 6. Volume Up / Down 7. Time 8. Navigation buttons 9. OK / Select 10. Back / Previous menu 11. Coloured buttons; Red button - Zoom Green button - Repeat Yellow button - Root Blue button - Title 12. Rewind 13. Pause 14. Play 15. Stop 16. Fast forward 17. Exit 18. DVD menu 19. Subtitle language selection 20.
General DVD Operation (if DVD is available) You can operate DVD, movie CD, music or picture CD’s content by using the proper buttons on your remote control. Below are main functions of commonly used remote control buttons.