MULTIFUNCTIONAL DIGITAL SYSTEMS Operator's Manual for Wireless LAN Module GN-1060
©2010 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TTEC. No patent liability is assumed, however, with respect to the use of the information contained herein.
Preface Thank you for purchasing TOSHIBA Multifunctional Digital Systems or Multifunctional Digital Color Systems. This manual explains the instructions for Wireless LAN Module GN-1060. Read this manual before using your Multifunctional Digital Systems or Multifunctional Digital Color Systems. Keep this manual within easy reach, and use it to configure an environment that makes best use of the e-STUDIO’s functions.
Trademarks y y y y y y y y y y y y y 2 The official name of Windows XP is Microsoft Windows XP Operating System. The official name of Windows Vista is Microsoft Windows Vista Operating System. The official name of Windows 7 is Microsoft Windows 7 Operating System. The official name of Windows Server 2003 is Microsoft Windows Server 2003 Operating System. The official name of Windows Server 2008 is Microsoft Windows Server 2008 Operating System.
Precautions Precautions for Use This product is classified as “wireless equipment for stations of low-power data transmissions systems” under the Wireless Telegraphy Act, and does not require a radio transmission license. The law prohibits modification of the interior of this product. About TOSHIBA Wireless Solution The Wireless LAN Module is a wireless network Module that complies with the IEEE 802.11 standard on wireless LANs (Revision B/G).
WARNING Keep this product away from a cardiac pacemaker at least 22 cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Do not use the product inside a medical facility or near medical electric equipment. Radio waves can potentially affect medical electric equipment, thereby causing an accident due to malfunction. Do not use the product near an automatic door, fire alarm or other automatic control equipment.
Regulatory Information The TOSHIBA Wireless LAN must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards. Standards below are certified under the operation with the provided antenna (GN-3010). Do not use this product with other antennas. Canada - Industry Canada (IC) This device complies with RSS 210 of Industry Canada.
Hiermit erklärt TOSHIBA TEC die Übereinstimmung des Gerätes GN-1060 mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien) 0( 7+1 3$5286$ TOSHIBA TEC '+/:1(, 27, GN-1060 680025):1(7$, 3526 7,6 286,:'(,6 $3$,7+6(,6 .$, 7,6 /2,3(6 6&(7,.
Regulatory Notice for Channel Use in France The number of channels that can be used for wireless LAN differs from country to country. In France however, user only 4 channels (channel 10, 11, 12, 13) when using wireless networks. y Channel 10 (2457 MHz) y Channel 11 (2462 MHz) y Channel 12 (2467 MHz) y Channel 13 (2472 MHz) France limited to 2446.5-2483.5 MHz Indoor use. Belgium limited to 2400-2483.5 MHz Indoor, 2460-2483.5 MHz Outdoor use.
CONTENTS Preface....................................................................................................................................... 1 Precautions ............................................................................................................................... 3 Chapter 1 SETTING UP WIRELESS NETWORK Before Setting Up Wireless Network .................................................................................... 12 Planning for installation ...........................
10 CONTENTS
SETTING UP WIRELESS NETWORK 1. This chapter describes about the preparations before setting up the wireless settings of the equipment. Before Setting Up Wireless Network .................................................................................... 12 Planning for installation ........................................................................................................................................12 Setting Up the Infrastructure Mode ..................................................
1 SETTING UP WIRELESS NETWORK Before Setting Up Wireless Network This product is a Wireless LAN Module using the 2.4 GHz spectrum diffusion system, and is compatible with IEEE Standard 802.11g and 802.11b for wireless LAN.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Determine the SSID In the wireless network, the same SSID (Service Set ID) must be assigned in each wireless device. Only wireless devices that have the same SSID assigned to them can communicate with each other through the wireless network. In the Infrastructure Mode, the SSID is usually set in the Access Point. Therefore, you must set the same SSID in this equipment to communicate through the wireless network via the Access Point.
1 SETTING UP WIRELESS NETWORK WEP The WEP is a data encryption method using the WEP key between the Access Point and other wireless devices. Compared with WPA/WPA2 and WPAPSK/WPA2PSK, the WEP is less security. If the wireless network is configured in the Infrastructure Mode and the Access Point supports WPA/WPA2 or WPAPSK/WPA2PSK, it is recommended to use WPA/ WPA2 or WPAPSK/WPA2PSK rather than WEP. The WEP authentication is available for both the Infrastructure Mode and Ad Hoc Mode.
1 SETTING UP WIRELESS NETWORK Setting Up the Infrastructure Mode The wireless settings can be operated from the Control Panel of this equipment. When setting up the equipment for the wireless network in the Infrastructure Mode, follow the steps below. 1. Select the network type P.15 “Select network type” 2. Specify the SSID P.18 “Specify SSID” 3. Select the security mode P.
1 SETTING UP WIRELESS NETWORK 5 Press the [WIRELESS SETTINGS]. The WIRELESS SETTINGS menu is displayed. 6 Press the [WIRELESS SETTINGS]. The WIRELESS SETTINGS screen is displayed. It may take a time to display the WIRELESS SETTINGS screen. 7 Press the [ON] and press the [NEXT]. The NETWORK TYPE screen is displayed.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 8 Press the [INFRASTRUCTURE] and press the [NEXT]. 9 The SSID SETTINGS screen displayed. Continue to the procedure for specifying the SSID. P.
1 SETTING UP WIRELESS NETWORK Specify SSID When you select the Infrastructure Mode for the network type, you can specify the SSID by selecting the available network list or manually entering the SSID. P.18 “Selecting the SSID from the available network list” P.19 “Entering the SSID manually” If you are not sure how the SSID must be specified, see the following section to determine the SSID. P.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 3 Press the [NEXT]. 4 The WIRELESS LAN SECURITY SETTINGS screen is displayed. Continue to the procedure for specifying the security mode. P.21 “Select security mode” Entering the SSID manually 1 Press the [SSID]. The letter entry screen is displayed.
1 SETTING UP WIRELESS NETWORK 2 Enter the SSID using the keyboard and digital keys and press the [OK]. The screen returns to the SSID SETTINGS screen. 3 Press the [NEXT]. 4 The WIRELESS LAN SECURITY SETTINGS screen is displayed. Continue to the procedure for specifying the security mode. P.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Select security mode After specifying the SSID, you must select the security mode for your wireless network. The procedure to configure the security mode varies depending on the security mode that you select. P.21 “Selecting WPA/WPA2 security mode with EAP-TLS protocol” P.25 “Selecting WPA/WPA2 security mode with PEAP protocol” P.28 “Selecting WPAPSK/WPA2PSK security mode” P.30 “Selecting WEP security mode” P.
1 SETTING UP WIRELESS NETWORK 2 Press the [EAP-TLS] and press the [NEXT]. The WIRELESS AUTHENTICATION (EAP-TLS) screen is displayed. Setting PMK cache When the [WPA2] is selected in step 1, the PMK cache can be switched to ON or OFF. When the [WPA] is selected, the item for setting PMK cache is not displayed. 3 Press the [EAP USER NAME]. The letter entry screen is displayed. 4 Enter the EAP user name using the keyboard and digital keys and press the [OK].
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 5 Press the [NEXT]. The WIRELESS AUTHENTICATION - USER CERTIFICATION screen is displayed. 6 Specify the following items and press the [NEXT]. y ENCRYPTION BETWEEN AP AND STA. Select the encryption type that is used for the communication between Access Point and this equipment. [TKIP] — Select this to use TKIP encryption. The TKIP provides a different key for per packet with a message integrity check.
1 SETTING UP WIRELESS NETWORK 7 Confirm the settings and press the [FINISH]. The shutdown screen is displayed. If you want to change the settings, press the [PREV] to move back to the screen that you want to change and then repeat the operation. 8 Press the [YES] to shutdown the equipment. The wireless settings apply after restarting the equipment.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Selecting WPA/WPA2 security mode with PEAP protocol Using the WPA/WPA2 with the PEAP protocol, you must install the CA certification file in the equipment. This equipment uses the user name and password to authenticate the access rights to the wireless network, and the RADIUS server authenticate this equipment using the CA certification file.
1 SETTING UP WIRELESS NETWORK 3 Enter the following items and press the [NEXT]. y [EAP USER NAME] Press this to enter the EAP user name that is used for the authentication. In the EAP USER NAME, enter the user name in “User Name@FQDN” format. Example: wlanuser@toshiba.com y [EAP PASSWORD] Press this to enter the EAP password that is used for the authentication. y [RETYPE PASS] Press this to enter the EAP password again that you enter in the EAP PASSWORD field.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 5 Confirm the settings and press the [FINISH]. The shutdown screen is displayed. If you want to change the settings, press the [PREV] to move back to the screen that you want to change and then repeat the operation. 6 Press the [YES] to shutdown the equipment. The wireless settings apply after restarting the equipment.
1 SETTING UP WIRELESS NETWORK Selecting WPAPSK/WPA2PSK security mode The WPAPSK/WPA2PSK is an authentication method using the PSK (Pre-Shared Key) between the Access Point and other wireless devices. To access the wireless network using the WPAPSK/WPA2PSK authentication, the same PSK Path Phrase must be assigned in both the Access Point and other wireless devices.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 3 Specify the following items and press the [NEXT]. y TRANSMIT POWER Select the low transmit power if you want to limit the area that the wireless communication is enabled. If you do not have to limit the area, select [100%]. y TRANSMIT RATE Select the transmit data capacity for wireless communication. If you do not have to specify the fixed rate, select [AUTO].
1 SETTING UP WIRELESS NETWORK Selecting WEP security mode The WEP is a data encryption method using the WEP key between the Access Point and other wireless devices. Compared with WPA/WPA2 and WPAPSK/WPA2PSK, the WEP is less security. If the wireless network is configured in the Infrastructure Mode and the Access Point supports WPA/WPA2 or WPAPSK/WPA2PSK, it is recommended to use WPA/ WPA2 or WPAPSK/WPA2PSK rather than WEP. 1 Press the [WEP] button and press the [NEXT].
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 3 Specify the following items and press the [NEXT]. y TRANSMIT POWER Select the low transmit power if you want to limit the area that the wireless communication is enabled. If you do not have to limit the area, select [100%]. y TRANSMIT RATE Select the transmit data capacity for wireless communication. If you do not have to specify the fixed rate, select [AUTO].
1 SETTING UP WIRELESS NETWORK Selecting no security mode You can also set no security for wireless access. If you do not set no security, anyone how knows the SSID can connect to the wireless network. Therefore, it is recommended to set the security if it is possible. 1 Press the [NONE] and press the [NEXT]. The TRANSMIT POWER and RATE SETTING screen is displayed. 2 Specify the following items and press the [NEXT].
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 3 Confirm the settings and press the [FINISH]. The shutdown screen is displayed. If you want to change the settings, press the [PREV] to move back to the screen that you want to change and then repeat the operation. 4 Press the [YES] to shutdown the equipment. The wireless settings apply after restarting the equipment.
1 SETTING UP WIRELESS NETWORK Setting up the Ad Hoc Mode The wireless settings can be operated from the Control Panel of this equipment. When setting up the equipment for the wireless network in the Infrastructure Mode, follow the steps below. 1. Select the network type P.34 “Select network type” 2. Specify the SSID P.37 “Specify SSID” 3. Select the security mode P.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK 5 Press the [WIRELESS SETTINGS]. The WIRELESS SETTINGS menu is displayed. 6 Press the [WIRELESS SETTINGS]. The WIRELESS SETTINGS screen is displayed. 7 Press the [ON] and press the [NEXT]. The NETWORK TYPE screen is displayed.
1 SETTING UP WIRELESS NETWORK 8 Press the [AD HOC] and press the [NEXT]. You can specify the between 1 to 11 for the channel. However, if there is a channel that has already been used for Ad Hoc network, use the same channel. 9 The SSID SETTINGS screen displayed. Continue to the procedure for specifying the SSID. P.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Specify SSID When you select the Ad Hoc Mode for the network type, you can specify the SSID by entering the SSID manually. If you are not sure how the SSID must be specified, see the following section to determine the SSID. P.13 “Determine the SSID” 1 Press the [SSID]. The letter entry screen is displayed. 2 Enter the SSID using the keyboard and digital keys and press the [ENTER] button. The screen returns to the SSID SETTINGS screen.
1 SETTING UP WIRELESS NETWORK 4 The WIRELESS LAN SECURITY SETTINGS screen is displayed. Continue to the procedure for specifying the security mode. P.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Select security mode After specifying the SSID, you must select the security mode for your wireless network. The procedure to configure the security mode varies depending on the security mode that you select. P.39 “Selecting WEP security mode” P.41 “Selecting no security mode” y If the Ad Hoc Mode, only WEP or NONE can be selected for the security mode.
1 SETTING UP WIRELESS NETWORK 3 Select the transmit power and press the [NEXT]. Select the low transmit power if you want to limit the area that the wireless communication is enabled. If you do not have to limit the area, select [100%]. 4 Confirm the settings and press the [FINISH]. The shutdown screen is displayed. If you want to change the settings, press the [PREV] to move back to the screen that you want to change and then repeat the operation. 5 Press the [YES] to shutdown the equipment.
1 SETTING UP WIRELESS NETWORK 1.SETTING UP WIRELESS NETWORK Selecting no security mode You can also set no security for wireless access. If you do not set no security, anyone how knows the SSID can connect to the wireless network. Therefore, it is recommended to set the security if it is possible. 1 Press the [NONE] and press the [NEXT]. The TRANSMIT POWER and RATE SETTING screen is displayed. 2 Select the transmit power and press the [NEXT] button.
1 SETTING UP WIRELESS NETWORK 4 Press the [YES] to shutdown the equipment. The wireless settings apply after restarting the equipment.
1 SETTING UP WIRELESS NETWORK Disabling Wireless Network When you enable the wireless network, the on-board NIC (Network Interface Card) will be disabled. If you want to connect the equipment to wired network via the on-board NIC, you must disable the wireless network. 1 Press the [USER FUNCTIONS] button on the control panel to enter the User Functions menu. 2 Press the [ADMIN]. 3 Press the [PASSWORD] button. The ADMINISTRATOR PASSWORD screen is displayed. The input screen is displayed.
1 SETTING UP WIRELESS NETWORK 6 Press the [WIRELESS SETTINGS]. The WIRELESS SETTINGS screen is displayed. 7 Press the [OFF] and press the [NEXT]. The NETWORK TYPE screen is displayed. 8 Press the [FINISH]. The shutdown screen is displayed. 9 Press the [YES] to shutdown the equipment. The wireless settings apply after restarting the equipment.
APPENDIX 2. This chapter describes the specification and glossary of terms. Specification ........................................................................................................................... 46 Troubleshooting ..................................................................................................................... 47 Glossary ..................................................................................................................................
2 APPENDIX Specification Item Description Transmission Format IEEE 802.11g standard Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplexing (OFDM) Data Transmission Speed 54, 24, 11, 5.5, 2, 1 Mbps (fixed/automatic) Access Method CSMA/CA Transmission Packet IEEE 802.
2 APPENDIX Troubleshooting When Error Messages are Displayed If any error messages are displayed on the touch panel, see the following table to troubleshoot the problems for the Wireless LAN. Error Message Troubleshooting Bad certificate Unsupported certificate is installed. Reinstall the appropriate certificate. This equipment supports md5RSA and sha1RSA certificate only. Bad record mac SSL Key exchange failed. Turn the power OFF and then ON to restart the equipment.
2 APPENDIX Glossary Ad hoc mode A type of network for wireless LAN communications. In this mode a network is easily built because no access point is required. However, this mode is not available for multiple simultaneous communications due to its poor extensibility; in other words, it is unsuitable for wireless LAN communication connecting many devices. AP (Access Point) Stands for Access Point.
2 APPENDIX 2.APPENDIX SSID (Service Set ID) A network ID for wireless LAN communications. To identify terminals or access points that belong to the same wireless LAN network, the same SSID must be set for each device. Communications among devices with different SSIDs are not available.
INDEX A AD HOC ...................................................................36 Ad Hoc Mode ............................................................12 AES (CCMP) .............................................................13 AVAILABLE NETWORK .............................................18 E EAP PASSWORD ......................................................26 EAP USER NAME .............................................. 22, 26 EAP-TLS ............................................................
52 INDEX
GN-1060 OME10008200
MULTIFUNCTIONAL DIGITAL SYSTEMS Operator’s Manual for Wireless LAN Module GN-1060 2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN ©2010 TOSHIBA TEC CORPORATION All rights reserved R100520J2800-TTEC VerB 2010-07
