DECLARATION OF CONFORMITY Manufacturer : TOSHIBA TEG Corporation Address 570 Ohio, Ohio-Cho, Yamagata-Gun, Shikoku-Ken, 410-2323 Japan declares that following product Product Name : Bar Code Printer Model © B-48X-YY Options : All conforms to the following product specifications Safety : EN 60950 EMC : ENS5022 EN 61000-4-2 IEC 1000-4-3 EN 61000-4-4 Harmonics : Supplementary Information The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC, and the EMC directive 89/336/EEC
ENGLISH VERSION EM-33034 TABLE OF CONTENTS 1. INTRODUCTION 1.1 Applicable Model . 1.2 Accessories 2. SPECIFICATIONS we E-1 2.1 Printer ~E2-1 2.2 Options E-2 2.3 Media... ~E2-3 2.4 Ribbon 3. OVERVIEW 3.1 Front/Rear View 3.2 Operation Panel .. 5. INSTALLING THE PRINTER... 5.1 Connecting the Power Cord and Cables 5.2 Procedure for Fitting Fan Filter 6. LOADING THE MEDIA 7. LOADING THE RIBBON 8. INSERTING THE OPTIONAL FLASH MEMORY CARD... 9. CARE/HANDLING OF THE MEDIA AND RIBBON 10. GENERAL MAINTENANCE 10.
ENGLISH VERSION EM-330341 1. INTRODUCTION 1. INTRODUCTION 1. INTRODUCTION Thank you for choosing the TEC 8-6 series transliterate printer. i high performance printer is equipped with superior hardware including the specially developed (¥ dots/mm, 263-2 dots/i inch) near edge print head which will allow very clear print at a maximum speed of 5% mm/sec. (oy The media supply | is internal. 30438 12 7 ob applications ard. McNaughton.
ENGLISH VERSION EM-33034} ¢ 1. INTRODUCTION 1. INTRODUCTION Safety Precautions This Owner's Manual and the products {machines} which you have purchased contain indications which should be observed in order to use the machines safely and prevent harm to yourself and others and damage to property. The meanings of these indications and symbols are given below. Read these indications and become familiar with their contents before reading this Owner's Manual.
ENGLISH VERSION EM-330341 1. INTRODUCTION . 1. INTRODUCTION ® Do not scratch, damage or modify ® Continued use of the machines in the power cords, Also, do not place an abnormal condition such as when heavy objects on, pull on, or excess machines are producing smoke or | lively band the cords, as this may strange smells may cause five ar cause fire or electrical shock. electric shock. In these cases, I SRY immediately turn off the power switches and disconnect the power cord plugs from the outset.
INTRODUCTION FN ENGLISH VERSION £M1-330341 1. INTRODUCTION = Be sure to move large scale machines with twa or more people. in ® When unplugging the power cords, be sure to hold and pull on the plug addition, machines should be moved Disconnect ihe plug. portion. Pulling on the cord portion after first confirming that connecting may cut or expose the internal wires wires between machines and and cause five or electric shock. externally connected wires, alc. have 7 4, been removed.
2. SPECIFICATIONS ENGLISH VERSION EM-330341 2.1 Printer 12 2. SPECIFICATIONS ~ Tsk 2.1 Printer — J Model 2 tem Supply voltage vl AG 220V ~ 240V + 10%, ~15%, 50Hz Power consumption IT; Operating temperature range Relative humidity Print head Printing methods Print speeds 4 \ < Maximum print width Dispensing modes Message display < © Dimensions Weight Available bar code types < SN Fonts Rotations Standard interface Optional interfaces I br PH, BOW maximum (standby: 250mA, 8) 5°C ~ 40°C (41°F ~ 104°F) 25% ~ 85
Option Name Type Usage 3 wing ~~ Gutter module B-4205-QM A stop and cut swing cutter | B-4700-10-QM VF PC board is equipped with the fle ash. memory Lard | interface, Electronics interface and expansion I/O A BE purchase the I/F PC board, please inquire at ; Your distributorship.
ENGLISH VERSION EM-330341 2. SPECIFICATIONS 2.3 Media 2.3 Media ter trot following Black Mark Tag paper Black Mark Stop @ {on reverse side} ® {on reverse side) position \ p Tag paper tT position cu 7 TEE 2 © cut position FPL” TC . position EB i concatenate coordinate coordinate Feed direction Fig. 2-1 Label dispensing mode Batch mode Strip mode tag 10.0 ~ 998.6 25.4 ~ 9090 22 220.2 50.8 20 ~ 108.0 Effective Label tint length Tag nt S| sl lack mark | Maximum effective le for an the fly issue NOTES: 1.
Fh SECT-13 Jr #6 Tag plan biz: sow 3p 258m 624 Bar: 4-1-2 BER COZEN El BEIGE (A) {mm} Hvk O51 578 ~ETTBL | sob Tor dy | Ts say | BA] 100 | 254 | 5sec:1020 | 57/seciafo 380 7 INE IF nx 27300 ® SEF gy |B] 100 254 #5 27300 | 2730.0 Lo. Bi 8.0 234 25.04% & mE | BX 2728.0 2724.0 GEE Bi 508 = sere BX 1120 me Boh 478 Dm BX 109.0 earn Fork BA 500 ER-r BX 100 IN _ Ba 100 & Harte Bx 106.702 say 21.4 230 7 | op BEEF BA 2726.0 OB 23.0 : BX | 27260 2726.0 An-7y7 XA 1.
ENGLISH VERSION EM-33034) 3. OVERVIEW 3.1 Front/Rear View 3. OVERVIEW 3.1 Front/Rear View Front View Rear View Outlet] high-speed PC Top Cover FCHCLA, Card inter bl-—{ 3 Message Display (1.CD) Supply Window ow ht (22090) Serial Interface Connector (RS-232C Parallel I/F Connector Operation Panel (Electronics) {Option) Expansion VO Interface Connector {Option) Power Switch Fig. 8-1 AC Power Inlet 0: OFF 1: ON Media Outlet 3.
4. DIP SWITCH FUNCTIONS ve SHE Ee avy, Fig. No. AE ENGLISH VERSION EM-330341 4. DIP SWITCH FUNCTIONS 4. DIP SWITCH FUNCTIONS The DIP switches are located to the right of the supply shaft. WARNING DIPPED Turn the POWER OFF before Supply Shaft omy switching the functions. Ribbon Shaft Fig. 4-1 DIPSO 0 (1) DIP Function Omg 1 #5 ‘Ato Ribbon ava function ot With og Languages fo display LCD error Cw, 2 FERRET Ep] message Cm German Frank ™ 3 Dutch Spanish Japanese 4 Valiant Not used, 5 Without.
ENGLISH VERSION £M1-330341 5. INSTALLING THE PRINTER 5.1 Connecting the Power Cord and Tablas 5. INSTALLING THE PRINTER 5.1 Connecting the Power Cord and Cables WARNING: Turn the POWER SWITCH to OFF before connecting the power cord or cables. Serial IF Cable ms-razor_ Expansion VO Cable . Option Option) eet Cable AB (Electronics) j (Option) Power Cord Fig.
Vv ENGLISH VERSION EM-330341 €. LOADING THE MEDIA 6. LOADING THE MEDIA 6. LOADING THE MEDIA The printer prints both labels and tags. 1. Turn off the power and open the top cover, 2. Turn the head lever to position @, then release the ribbon shaft holder plate. Top Cover Ribbon Shaft Holder Plate Head Lever Fig. 6-1 NOTES: 1. When the head lever is turned to position @, the print head is raised. 2. When the head lever is turned to position @ §, the print head and the pinch roller are raised. 3.
Vv ENGLISH VERSION EM-33034( 8, LOADING THE MEDIA 8. LOADING THE MEDIA 5. Put the media on the supply shaft. 8. Pass the media around the damper, then pull the media towards the front of the printer. Fix the remaining supply holder to the supply shaft with the punchers facing away from the printer. Nv Damper Matlab Supply Holder (FMHDO005502) Supply Shaft Fig. 6-3 7. insert the media into the paper holders of the media guide, adjust the media guides to the media width, and tighten the locking screw. 8.
ENGLISH VERSION EM-330341 8. LOADING THE MEDIA ® 8. LOADING THE MEDIA HW Removing the paper holders’ upper plates from the media guide © Remove the two T-4 X 8 screws to detach the media guide from the printer. Media Guide Ry" Screw (T-4 8) Fig. 6-5 @ Remove the SM-3x6 screw or the SM-3 8 screw to detach the paper holders’ upper plates from the media guide. Right (Loft) Screw (SM-3X8) Screw (SM-3x8) Paper Holder Paper Holder Fig. 6-6 ® Attach the media guide back in position.
Vv ENGLISH VERSION EM-33034) 8. LOADING THE MEDIA 6. LOADING THE MEDIA MW An easy way to set the black mark sensor position mn @ Pull the media about 500 mm out of the front of the printer, turn tha media back on it's self and feed it under the print head past the sensor so that the black mark can be seen from above. @ Adjust the sensor position to that of the black mark (the upper hole indicates the position of the black mark sensor}. Black Mark S Black Mark ach ari rosy {Fed Gap Sensor} Fig.
ENGLISH VERSION EM-330341 6. LOADING THE MEDIA 6. LOADING THE MEDIA pL HME TRY 10. The media is now loaded and the sensor pose set. Batch type: { / Selection Switch Fig. 6:9 NOTE: Set the selection switch to the STANDARDIZATION position. Improper setting can affect the print quality. Strip type: O Remove enough labels from the leading edge media to eave 500 mm of backing paper exposed. © Wind the backing paper onto the take-up spool and fix in position with the take-up clip.
~205 MBE RF To TOSHIBA TEC BRAE EEE 1 AEH LU FEU, ENGLISH VERSION EM-330341 6. LOADING THE MEDIA 6. LOADING THE MEDIA Cutter type: Where a cutter is fitted load the media as standard any feed it through the cutter module. ya NOTES: 1. Be sure lo cut the backing paper of label. Cutting labels Will cause the glue to stick to the cutter, which may affect the cutter quality and shorten the life. 2. {if the top edge of label winds onto the platen in cut issue/ settee -RIP-Swedes-10-00: 3.
ENGLISH VERSION EM-330341 7. LOADING THE RIBBON 7. LOADING THE RIBBON 7. LOADING THE RIBBON There are two types of media available for printing on, these are standard media and direct thermal media (a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal media. 1. When using a narrow width ribbon, slide the ribbon stoppers along the shafts to a position where the ribbon will be centered when it is fetid.
PC MEAL ENGLISH VERSION EM-330341 8. INSERTING THE OPTIONAL FEAST-MEMORY CARD genera 8. INSERTING THE OPTIONAL CARD Pec 4 8. INSERTING THE OPTIONAL FLASH-MEMORY CARD WARNING: PECK A Turn the power OFF when inserting or removing the flask-reemory card. CAUTION: protect he cards, discharge static electricity from your body by touching the printer rear cover prior to touching the memory cards. 1. Turn the power off. 2. Insert the fob baths card into the memory card slot on the rear of the printer. 3.
ENGLISH VERSION EM-330341 9. CARE/HANDLING OF THE MEDIA AND RIBBON | ’ 9. CARE/HANDLING OF THE MEDIA AND RIBBON 9. CARE/HANDLING OF THE MEDIA AND RIBBON CAUTION : Be sure to read carefully and understand the Supply Manual. Use only media and ribbon which meet specified requirements. Use of non-specified media and ribbon may shorten the head life and result in problems with bar code readability or print quality.
Vv ENGLISH VERSION EM-33034 10. GENERAL MAINTENANCE 10.3 Cleaning 10. GENERAL MAINTENANCE 10.1 Cleaning To help retain the high quality and performance of your printer it should be regularly cleaned. The greater the usage of the printer, the more frequent the cleaning. (i.e. low usage =weekly : high usage = daily). A print head cleaner is not enclosed with the printer, so please inquire at your local distributor. Turn the power off, Open the top cover. Turn the head lever to raise the print head.
ENGLISH VERSION EM-330341 10. GENERAL MAINTENANCE 10.3 Removing Jammed Paper 10.3 Removing Jammed Paper 1. Turn the power off. 2. Open the top cover, 3. Turn the head lever to position (3, then release the ribbon shaft holder plate. 4. Remove the black screw to detach the media guide plate. (See Fig. 10-2.) &. Removes the ribbon and media. 6. Remove the jammed paper. DO NOT USE any sharp implement or tool as these could damage the printer, 7.
ENGLISH VERSION EM-330341 10. GENERAL MAINTENANCE . 10.3 Removing Jammed Peter HM Cleaning the Cutter Unit WARNING: 1. Be sure to turn the power off before cleaning the cutter unit. 2. The cutters are sharp and care should be taken nat to injure yourself when cleaning. Loosen two screws and remove the cutter cover. Remove the white screw and media guide. Remove the jammed paper and trash.
ENGLISH VERSION EM-330341 10. GENERAL MAINTENANCE 10.4 Threshold Setting ee 10.4 Threshold Setting For the printer to maintain a constant print position it uses the feed gap sensor to detect the gap between labels by measuring the amount of light passing through the media. When the media is pro printed, the darker {or more dense) inks can interfere with this process causing paper jammed errors. To get around this problem a minimum threshold can be set for the sensor in the following way.
5.5 THRESHOLD SETTING (REPRINTED LABEL) 8.8. oe of Threshold Setting missive sensor~and correct the print position automatically to obtain constant print position” When the i: is printed, the printer detects the gap between the labels using the train reprinted label is used, however, some inks may prevent proper position erection.
Tirolean sinks sis ily (12) The printer feeds the label untie the [PAUSE] key is released. (13) When the [PAUSE] key is released after more than 1.5 sheets of the label are fed, the printer stops feeding the label. {Threshold setting for the selected sensor is completed.) I T I pavilion [TTT TTT] RESTART (14) Press the [RESTART] key. + TTT } oll rivaled TTT (18) ding a ST Command 0 ul I tin (16) The label is printed according to the command issued from the PC.
11. TROUBLESHOOTING 11. TROUBLESHOOTING ENGLISH VERSION EM-330341 1. TROUBLESHOOTING WARNING: assistance, If you cannot solve a problem with the following solutions, do not attempt to repair it yourself, Turn the power off, unplug the printer, then contact your Authorized Service representative for Error Message Problem Solution PAPER JAM reins 1. The media is not fitted correctly, 2. The media path is jammed and does not deaf smoothly. 3. The installed media type does not match the selected sensor. 4.
11. TROUBLESHOOTING ENGLISH VERSION EM 1-330341 11. TROUBLESHOOTING Error Message Problem Solution EXCESS HEAD TEMP The print head is too hot. Turn the power off and decrease the print head temperature. RIBBON ERROR Ehk® There is a fault with the ribbon sensor. Turn the power off, Contact your Authorized Service representative. CUTTER ERROR EEE Media is jammed in the cutter. Remove the jammed media and feed the undamaged media through the cutter. — Press the[RESTART | key.
11. TROUBLESHOOTING ENGLISH VERSION EM-33034i 11. TROUBLESHOOTING Error Message Problem Solution example) When an error is detected in a Correct the command and re-send it POPCORN ; QATAR, command 18 bytes of the command again, Command error | 8r® displayed. i 0300, 2, 2 (ESC, LF, NUL are not displayed.) Other Error Hardware or software trouble. Turn the power off then an again, If Message the problem still exists turn the power off and contact your Authorized Service representative.