TOSHIBA 3500 Portable Personal Computer User’s Manual
Copyright © 2002 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA 3500 Portable Personal Computer User’s Manual First edition November 2002 Disclaimer This manual has been validated and reviewed for accuracy.
FCC information Product Name : Portégé 3500 Model number : PP350 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Type of service Your modem is designed to be used on standard-device telephone lines. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party lines service is subject to state tariffs. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request.
Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other ent
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed. ❑ The preferred method of dialing is to use DTMF tones (ATDT...
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.
Table of Contents Preface Manual contents .................................................................................xix Conventions ......................................................................................... xx Abbreviations ........................................................................................ xx Icons .................................................................................................... xx Keys ...........................................................
Chapter 3 Getting Started Setting up your work space ............................................................... 3-2 General conditions .............................................................................. 3-2 Placement of computer ....................................................................... 3-2 Seating and posture ............................................................................ 3-3 Lighting .................................................................................
Wireless LAN .................................................................................... 4-14 Bluetooth wireless technology ........................................................... 4-14 Wireless communication switch ........................................................ 4-15 Wireless communication Indicator .................................................... 4-15 LAN .................................................................................................... 4-16 LAN cable types .....
Chapter 6 Power and Power-Up Modes Power conditions ................................................................................ 6-1 Power indicators ................................................................................ 6-3 Battery indicators ................................................................................ 6-3 DC IN indicator .................................................................................... 6-3 Power indicator ................................................
Removing an SD card .......................................................................... 8-6 Compact Flash .................................................................................... 8-7 Installing a Compact Flash module ..................................................... 8-7 Removing a Compact Flash module .................................................... 8-8 Memory expansion ...........................................................................
Bluetooth .......................................................................................... 9-20 TOSHIBA support ............................................................................. 9-21 Before you call ................................................................................. 9-21 Where to write .................................................................................. 9-21 Appendixes Appendix A Specifications ...............................................................
Preface Congratulations on your purchase of the TOSHIBA 3500 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, highperformance computing. This manual tells how to set up and begin using your TOSHIBA 3500 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
User's Manual Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Conventions The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
User's Manual xxii
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
User's Manual PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.
Introduction Equipment checklist ........................................................................... 1-1 Features .............................................................................................. 1-3 Special features .................................................................................. 1-7 Utilities ................................................................................................. 1-9 Options ...................................................................
INTRODUCTION
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
User's Manual INTRODUCTION • • • • • • ❑ Documentation: • • • • • ❑ 1-2 TOSHIBA Common Modules TOSHIBA Console TOSHIBA Network Device Switch TOSHIBA Skins for Windows Media Player Online manual Sensiva Symbol CommanderTM PORTÉGÉ 3500 Portable Personal Computer User’s Manual Microsoft Windows XP Tablet PC Edition manual package Instruction Manual for Safety & Comfort End User License Agreement International Limited Warranty (ILW) Instruction (This instruction is included only with computers sold in ILW
Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in Mobile Intel® Pentium® III processor 1.33 GHz - M with Enhanced Intel® SpeedStep™ Technology incorporates a math coprocessor and 32 KB cache.
INTRODUCTION User's Manual Built-in Graphics controller 12.1" XGA-TFT, 1024 horizontal x 768 vertical pixels, up to 16 M colors. This resolution can be changed in Tablet PC mode. Refer to xxxxxxx for the details. A 128-bit graphics controller maximizes display performance. Refer to Appendix B for more information. Keyboard Built-in 84 keys or 85 keys, compatible with IBM enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys.
Features External monitor Universal Serial Bus (USB2.0) This infrared port is compatible with Infrared Data Association (IrDA 1.1) Fast InfraRed (FIR) standards. It enables cableless 4 Mbps data transfer with IrDA 1.1 compatible external devices. 15-pin, analog VGA port supports VESA DDC2B compatible functions. The computer has two Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than USB 1.1 standard. (The ports also support USB 1.1.).
User's Manual INTRODUCTION LAN Wireless LAN Bluetooth The computer is equipped with a LAN card that supports Ethernet LAN (10 Mbit/s, 10BASE-T) and Fast Ethernet LAN (100 Mbit/s, 100BASE-Tx). In some markets, the computer is equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with the IEEE 802.11 Standard (Revision B). It supports data transfer up to 11 Mbit/s. It has Frequency Channel Selection (2.
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Keypad overlay Gray keys with gray lettering make up the keypad overlay, which lets you use the keyboard for ten-key operations or cursor control.
INTRODUCTION User's Manual Instant security A hotkey function blanks the screen and disables the computer providing quick and easy data security. Panel power on/off This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the System Power Mode window in Power Saver. Auto power on This feature lets you set a time and date for the computer to turn on automatically.
Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme files. TOSHIBA Power Saver To access this power savings management program in Windows XP, open the Control Panel, click Performance and Maintenance and click the TOSHIBA Power Saver icon.
User's Manual INTRODUCTION Sound drivers A broad range of audio controls are possible through the ALi sound driver, including Software Synthesize, Mic volume and Power management. Click Control Panel and click the ALi sound setup icon to adjust power management settings. For other sound settings, use the Windows Device Manager, Multimedia panel or volume control dial.
Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory modules Two memory expansion slots are available for installing 128, 256 or 512 MB memory modules. The modules are SD Random Access Memory (SD-RAM), 144-pin, SO Dual Inline Memory Modules (SO-DIMM). Battery Pack A Battery Pack (PA3228U) can be purchased from your TOSHIBA dealer. The Battery Pack is identical to the one that came with your computer.
INTRODUCTION User's Manual 1-12
Chapter 2 The Grand Tour THE GRAND TOUR Front with the display closed ............................................................ 2-1 Left side ............................................................................................... 2-2 Right side ............................................................................................ 2-4 Back side ............................................................................................. 2-4 Underside .......................................
THE GRAND TOUR
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. BATTERY LOCK DISPLAY LATCH INFRARED PORT VOLUME CONTROL MICROPHONE JACK HEAD PHONE JACK BATTERY LOCK INDICATOR POWER SOURCE/ SYSTEM INDICATORS BATTERY RELEASE LEVER Figure 2-1 Front of the computer with the display closed Headphone jack A standard 3.
User's Manual Battery lock The battery lock prevents inadvertent release of the Battery Pack. Battery lock indicator This indicator shows the status of the Battery lock by color: red for unlocked and green for locked status respectively. THE GRAND TOUR Display latch Power source/ system indicators Infrared port Battery release lever This latch secures the LCD panel in its closed position. Push the latch to open the display. LEDs let you monitor the status of various computer functions.
Left side PC card slot CB A PC card slot can accommodate one 5 mm PC card (Type II). The slot supports 16-bit PC cards and CardBus PC cards. CAUTION: Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions. CAUTIONS: 1.
User's Manual Right side THE GRAND TOUR Figure 2-3 shows the computer’s right side. SECURITY LOCK SLOT Figure 2-3 The right side of the computer Security lock slot A security cable is attached to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. Back side LAN ACTIVE INDICATOR Figure 2-4 shows the computer’s back side.
Underside External monitor port Two Universal Serial Bus ports are on the back side. The ports comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard. (The ports also support USB 1.1.) CAUTION: Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer's circuitry. LAN jack Ether LAN active indicator (yellow) Link indicataor (green) This jack lets you connect to a LAN.
User's Manual The computer is equipped with two expantion memory slots (sockets). Use these slots (sockets) to install memory module to increase your computer’s memory. Refer to the Memory expansion section in Chapter 8, Optional Devices for the detail. Battery Pack The Battery Pack powers the computer when the AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-Up Modes, describes how to access the Battery Pack.
Front with the display open Display screen The full-color LCD displays high-contrast text and graphics and is compatible with the industry standard Video Graphics Array (VGA). The LCD consists of up to 1024 × 768 pixels or dots. The computer has a Thin-Film Transistor (TFT) display. Refer to Appendix B. Display hinge Pen (Stylus) The display hinge holds the display screen at easy-to-view angles. Pen is contained on the left hand side of display. A pen enables data entry directly through display screen.
User's Manual Enter/Menu button THE GRAND TOUR Arrow button (2) Speaker This button functions as the same to Enter key when tapped, or shows the menu screen when pressed for more than a second. This button functions as the same to ↓ key. The speaker emits sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Indicators Figure 2-7 shows the indicators, which light when various computer operations are in progress.
Indicators Power source/system indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes in orange. The Power indicator glows green when the computer is on. If you turn off the computer in Resume mode, this indicator blinks orange (one second on, two seconds off) while the computer shuts down. Battery The Battery indicator shows the condition of the charge.
User's Manual NUMERIC MODE THE GRAND TOUR ARROW MODE Figure 2-8 Keypad overlay indicators When the CapsLock indicator glows, the keyboard is in all-caps mode. CAPS LOCK Figure 2-9 CapsLock indicator Keyboard indicator Caps Lock Arrow mode Numeric mode 2-10 This indicator glows green when the alphabet keys are locked in uppercase. When the Arrow mode indicator lights green, you can use the keypad overlay (white labeled keys) as cursor keys.
AC adaptor AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. Figure 2-10 The AC adaptor CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer.
THE GRAND TOUR User's Manual 2-12
Chapter 3 Getting Started GETTING STARTED Setting up your work space ............................................................... 3-2 General conditions .............................................................................. 3-2 Placement of computer ....................................................................... 3-2 Seating and posture ............................................................................ 3-3 Lighting ..............................................................
GETTING STARTED
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User’s Manual Setting up your work space GETTING STARTED Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Setting up your work space ❑ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ❑ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility. ❑ If you use a paper holder, set it at about the same height and distance as the computer.
User’s Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright light that could shine directly in your eyes. ❑ If possible, use soft, indirect lighting in your computer work area.
Operating the computer in Tablet PC mode Operating the computer in Tablet PC mode NOTE: TOSHIBA 3500 computer can be used in two ways; ordinary Notebook PC and Tablet PC. You can use the computer as Tablet PC that is operated with attached Pen (Stylus) by turning LCD panel in 180 degrees and closing it. This manual calls the use as an ordinary Notebook PC as PC mode, and the use as Table PC as Tablet PC mode.
GETTING STARTED User’s Manual ❑ Remove all external peripheral devices and their connection cables from the computer before carrying. Remove all I/O devices such as PC Card, SD Card and Compact Flash that are connected (or inserted) to the computer. ❑ Do not drop the computer nor apply excessive impact on the computer. Do not leave the computer in an automobile where the computer is exposed to direct sunbeam. ❑ Do not put the computer in Tablet PC mode in a bag.
Connecting the AC adaptor 1. Connect the power cord to the AC adaptor. Figure 3-4 Connecting the power cord to the AC adaptor GETTING STARTED 2. Connect the AC adaptor’s DC output plug to the DC IN port on the back of the computer. Figure 3-5 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow.
User’s Manual Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Push down the display latch on the front of the computer to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. GETTING STARTED Caution: User reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Turning on the power Turning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter. 1. If the external diskette drive is connected, make sure it is empty. If a diskette is in the drive, press the eject button and remove the diskette. 2. Open the display panel. 3.
User’s Manual Starting up for the first time When you first turn on the power, the computer's initial screen is the Microsoft Windows XP Tablet PC edition Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully. NOTE: You cannot use the Pen when Windows is in Setup. Use keyboard or touch pad while Windows is setting up.
Turning off the power Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The hibernation feature does not save the status of peripheral devices. CAUTIONS: 1. Save your data. While entering hibernation mode, the computer saves the contents of memory to the HDD. However, for safety sake, it is best to save your data manually. 2.
User’s Manual Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4. See Chapter 5, Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click Start and click Turn Off Computer. 2. In Turn Off Computer, click Hibernate. The Standby icon will be displayed initially. To display the Hibernate icon press the Shift key. GETTING STARTED The computer will also enter Hibernate mode automatically when you: ❑ Press the power button. ❑ Close the lid (the Display).
Turning off the power Standby mode In standby mode, the power remains on, but the CPU and all other devices are in sleep mode. Standby precautions ❑ Before entering Standby mode, be sure to save your data. ❑ Do not install or remove a memory module while the computer is in standby mode. The computer or the module could be damaged.
User’s Manual NOTES: 1. When the computer is shut down in standby mode, the power indicator flashes in orange. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power. Standby limitations Standby will not function under the following conditions: ❑ Power is turned back on immediately after shutting down. ❑ Memory circuits are exposed to static electricity or electrical noise.
Restoring the preinstalled software from the Product Recovery CD-ROM Restoring the preinstalled software from the Product Recovery CD-ROM If preinstalled files are damaged, use the Product Recovery CD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below. CAUTION: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1.
GETTING STARTED User’s Manual 3-16
Chapter 4 Operating Basics OPERATING BASICS Using the Touch Pad .......................................................................... 4-1 Using the Pen (Stylus) ........................................................................ 4-2 Installing the pen ................................................................................. 4-4 Removing the pen ............................................................................... 4-5 Pen actions ................................................
OPERATING BASICS
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the Pen, the external diskette drive, the wireless communication, LAN and the internal modem. It also provides tips on caring for your computer and on heat dispersal. Using the Touch Pad To use the Touch Pad, simply press and move your finger tip across it in the direction you want the on-screen pointer to go.
User's Manual For some functions, you can tap the touch pad instead of pressing a control button. Click Tap the touch pad once Double-click Tap the touch pad twice Drag and drop 1. Select the material you want to move. 2. Leave your finger on the Touch Pad after selecting the material and move it. 3. Lift your finger to drop the item at a place where you want it. Scroll Vertical: Move your finger to and fro the right edge of the touch pad.
Using the Pen (Stylus) You can use the pen to execute actions and enter data. Hold the pen in a natural position and tap, press or trace on the screen lightly. Before you begin using the TOSHIBA3500 for the first time, you will need to calibrate the pen. Refer to Chapter 9, Pointing device in for the detail. CAUTIONS: Observe the following precautions on the handling of the Pen. 1. Do not tap or press the pen forcefully against the Display screen. It could damage the Pen and Display screen. 2.
User's Manual 9. Keep the small parts of the Pen such as the pen point or the knob of the side switch away from infant to prevent them to swallow NOTE: TOSHIBA is not liable to the quality problem of the products due to the use of the Pen in an environment where above conditions are not satisfied because of the use by unspecified number of users. OPERATING BASICS Installing the pen Figure 4-3 Installing the pen The pen is included in the product when purchased.
Using the Pen (Stylus) Removing the pen Figure 4-4 Removing the pen 1. To remove the pen from the groove, press the pen at the head. 2. Tail of the pen rises up.
User's Manual Pen actions You can use the pen to enter data, start programs, move objects and execute other actions. Single tap Lightly tap the tip of the pen on an object and lift it immediatey to execute an action. A single tap is similar to clicking the left touch pad control button. Double tap Lightly tap the tip of pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left touch pad control button.
Using the Pen (Stylus) Replacing the pen tip Figure 4-6 1. To replace the pen tip, pinch the tip with a draw-out tool and pull it out. 2. Insert a new tip into the pen at the flat end of the tip and press it to seat securely. NOTE: Short and worn pen point is difficult to pull out. Replace the pen point with refill before it becomes too short.
User's Manual Changing to the Tablet PC mode To change the PC mode to the Tablet PC mode, follow the instructions below. Figure 4-7 Changing to the Tablet PC mode (1) OPERATING BASICS CAUTION: Place the computer on a stable, flat place such as a desktop and rotate the display panel slowly, holding the panel at its lower part. The display panel is designed not to rotate more than 180 degrees. Rotating the display panel more than 180 degrees with an excessive force causes to damage the panel.
Changing to the Tablet PC mode 1. Open the display panel to the upright position. Figure 4-8 Changing to the Tablet PC mode (2) 2. Rotate the display panel clockwise slowly. OPERATING BASICS NOTE: Do not apply excessive rotating force to the display panel. It causes damage of the display panel.
User's Manual 3. Turn the Display latch tab in 180 degrees to the down side. OPERATING BASICS Figure 4-9 Changing to the Tablet PC mode (3) 4. Close the display panel slowly with LCD surface outside. Figure 4-10 Changing to the Tablet PC mode (4) 5. Turn the display latch downward. 6. Insert the display latch in the slit. 7. Press the display panel downward softly.
Changing to the PC mode Changing to the PC mode To change the Tablet PC mode to the PC mode, follow the instructions below. 1. Press the Display latch and raise the display to the upright position carefully. 2. Rotate the display counter-clockwise slowly. 3. Turn the display latch tab toward you for the next closing of the display. Using the USB FDD Kit A 3 1/2" external diskette drive module connects to the USB port. NOTE: The USB FDD Kit is an option with some models.
User's Manual CAUTION: Check the Disk-In-Use indicator when you use the diskette drive. Do not press the eject button, disconnect a drive cable or turn off the computer while the light is glowing. Doing so could destroy data and damage the diskette or the drive. NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating. 2. Do not set anything on top of the diskette drive. 3.
Using the USB FDD Kit Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Pull the diskette drive connector out of the USB port.
User's Manual Wireless communications The computer’s wireless communication function supports both wireless LAN and Bluetooth devices. In this chapter, the descriptions on Wireless LAN or Bluetooth are applicable to the model equipped with Wireless LAN or Bluetooth function respectively. Wireless LAN The wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN standard (Revision B).
Wireless communications Security Two advanced security mechanisms ensure a high level of security: ❑ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ❑ Encryption prevents eavesdropping and maintains link privacy. Wireless communication switch You can enable or disable wireless LAN and Bluetooth function, with the on/off switch. No transmissions are sent or received when the switch is off.
User's Manual LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature.
LAN 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN’s jack. Press gently until you hear the latch click into place. Figure 4-13 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below.
User's Manual Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, "howling" may be heard under certain conditions. Howling occurs when sound from the speaker is picked up in the microphone and amplified back to the speaker, which amplifies it again to the microphone.
Modem Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. 1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
User's Manual Properties menu Click the icon with the secondary mouse button to display the following menu. Figure 4-15 The menu list (Windows XP Tablet PC Edition) Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. OPERATING BASICS Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region.
Modem Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties. CAUTION: If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.
User's Manual Disconnecting To disconnect the internal modem cable, follow the steps below: 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ❑ Be careful not to spill liquids into the computer.
Heat dispersal ❑ Close the display panel when carrying. ❑ Do not put the computer in Tablet PC mode in a bag. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed.
OPERATING BASICS User's Manual 4-24
Chapter 5 The Keyboard Typewriter keys .................................................................................. 5-1 F1 … F12 function keys ...................................................................... 5-2 Soft keys: Fn key combinations ......................................................... 5-2 Emulating keys on enhanced keyboard ............................................... 5-2 Hotkeys ..............................................................................................
THE KEYBOARD
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hotkeys Hotkeys (Fn + another key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hotkeys, the current setting will be displayed as an icon. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad.
Soft keys: Fn key combinations Hibernation: When you press Fn + F4, the computer can enter Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you check the checkbox in the dialog box, it will not appear from the next time. Display selection: Press Fn + F5 to change the active display device. When you press these hot keys a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device.
User's Manual Wireless setting: If your computer has both Bluetooth and wireless LAN functions, you can press Fn + F8 to select which type of wireless communication you want to use. When you press these hotkeys, a dialog box will appear. Continue holding down Fn and press F8 to change the setting. If wireless communication is turned off, Disabled Wireless Communication Switch will be displayed. NOTE: If no wireless communication device is installed, no dialog box will appear.
Windows special keys Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay THE KEYBOARD Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
Generating ASCII characters Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
THE KEYBOARD User's Manual 5-10
Power and Power-Up Modes Power conditions ................................................................................ 6-1 Power indicators ................................................................................ 6-3 Battery indicators ................................................................................ 6-3 DC IN indicator .................................................................................... 6-3 Power indicator ..........................................................
POWER AND POWER-UP MODES
Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions continued Power on AC Battery • Operates adaptor charge is • LED: Battery off not above low connected battery DC IN off trigger point Battery • Operates charge is • LED: Battery below low flashes in orange battery DC IN off trigger point Battery Computer goes charge is into resume mode exhausted and shuts down No • Cannot operate battery • LED: Battery off installed 6-2 DC IN off Power off (no operation)
Power indicators The Battery, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status: Flashing in orange The battery charge is low. The AC adaptor must be connected to recharge the battery. Orange Indicates the AC adaptor is connected and charging the battery.
POWER AND POWER-UP MODES User's Manual Power indicator Check the Power indicator to determine the power status. Green Blinking in orange No light Indicates power is being supplied to the computer and the computer is turned on. Indicates the power was turned off while the computer was in Resume mode. The indicator turns on for one second and turns off for two seconds. Under any other conditions, the indicator does not light.
Care and use of the Battery Pack Real time clock battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: *** Bad RTC battery *** Check system. Then press [F1] key . . . . . .
POWER AND POWER-UP MODES User's Manual Safety precautions Mishandling of batteries can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, which could result in death or serious injury, if you do not follow instructions. Warning: Indicates a potentially hazardous situation, which could result it death or serious injury, if you do not follow instructions.
Care and use of the Battery Pack 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack's internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1.
POWER AND POWER-UP MODES User's Manual Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack's power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage.
Care and use of the Battery Pack When the power in the Battery Pack becomes low, the Battery indicator flashes in orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Resume mode (so you don’t lose data) and automatically turns off. You must recharge a Battery Pack when it becomes discharged.
POWER AND POWER-UP MODES User's Manual Battery charging notice The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. Also, to ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 86°F). ❑ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.
Replacing the Battery Pack Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer, for example, whether you enable batterypower saving options. The computer provides a battery save mode to conserve battery power.
POWER AND POWER-UP MODES User's Manual Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (3600 mAh) RTC battery 2 days (Resume mode) 25 days (Boot mode) 1 month Extending battery life To maximize the life of your Battery Pack: ❑ At least once a month, disconnect the computer from a power source and operate it on battery power until the Battery Pack fully discharges.
Replacing the Battery Pack When the Battery Pack reaches the end of its operating life you will need to install a new one. The life of the Battery Pack is generally about 500 recharges. If the Battery indicator flashes in orange shortly after fully recharging the battery, the Battery Pack needs to be replaced. You might also replace a discharged Battery Pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install Battery Packs.
POWER AND POWER-UP MODES User's Manual CAUTION: For environmental reasons, do not throw away a spent Battery Pack. Please return spent Battery Packs to your TOSHIBA dealer.
Installing the Battery Pack To install a Battery Pack, follow the steps below. CAUTION: The Battery Pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only battery recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the Battery Pack. 3. Secure the battery lock.
POWER AND POWER-UP MODES User's Manual Starting the computer by password If you registered a password as user, you must enter it to start the computer. For more information about how to set a password, refer to Chapter 7, HW Setup and Passwords. To start up the computer with the password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. 2. Enter the password. 3. Press Enter. NOTE: If you enter the password incorrectly three times in a row, the computer shuts off.
Panel power off POWER AND POWER-UP MODES Power-up modes The computer has the following power-up modes: ❑ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ❑ Hibernation: Data in memory is saved to the hard disk. ❑ Standby: Data is maintained in the computer's main memory. NOTE: Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started.
POWER AND POWER-UP MODES User's Manual 6-18
Chapter 7 HW Setup and Passwords HW SETUP AND PASSWORDS HW Setup ............................................................................................ 7-1 Accessing HW Setup .......................................................................... 7-1 HW Setup window ............................................................................... 7-1 Supervisor password ..........................................................................
HW SETUP AND PASSWORDS
Chapter 7 HW Setup and Passwords HW Setup TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority, USB, LAN, general, password and device configuration. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup.
User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. HW SETUP AND PASSWORDS About Display the HW Setup version.. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered Change or remove the password. (Default) Set the password.
HW Setup 4. If character strings match, the password is registered and the display changes to: Registered If they do not match, the following message appears. You must repeat from step 1. HW SETUP AND PASSWORDS Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks.
User's Manual Entering User Password in Tablet PC mode You can enter the user password through the virtual keyboard displayed on the screen when in Tablet PC mode. The procedure of entering the password is almost the same to the one in PC mode. HW SETUP AND PASSWORDS Tap the key on the virtual keyboard with pen (stylus) instead of typing the real keyboard to enter the password. Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices.
HW Setup CPU Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable Always High CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at its fastest speed. Always Low CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at low power consumption and low speed.
User's Manual Boot Priority Boot Priority Options HW SETUP AND PASSWORDS This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, diskette drive, CD-ROM* and LAN. (Default) FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: diskette drive, HDD, CD-ROM* and LAN.
HW Setup This procedure does not affect the settings. ❑ Use hot keys. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD, Network (LAN), PCA (ATA) card boot. HW SETUP AND PASSWORDS NOTE: A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. NOTES: 1.
User's Manual 2. When you assign a PC card HDD top priority, “PC” is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above. USB HW SETUP AND PASSWORDS USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
Supervisor password Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. 7-9 HW SETUP AND PASSWORDS The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file.
HW SETUP AND PASSWORDS User's Manual 7-10
Chapter 8 Optional Devices OPTIONAL DEVICES PC cards .............................................................................................. 8-2 Installing a PC card ............................................................................. 8-2 Removing a PC card ........................................................................... 8-4 SD cards .............................................................................................. 8-5 Installing an SD card .........................
OPTIONAL DEVICES
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
User’s Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards PC CARD After installing the card, refer to the card’s manual and check the configuration in Windows to make sure it is appropriate for your card.
User’s Manual Removing a PC card To remove the PC card, follow the steps below: 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5. Pinch the PC card and draw it out.
SD cards SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various capacities SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate MultiMedia cards. CAUTION: Keep foreign objects out of the SD card slot.
User’s Manual Removing an SD card To remove an SD card, follow the steps below: 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. OPTIONAL DEVICES 4. Pinch the SD card and draw it out. SD CARD SD CARD INDICATOR Figure 8-4 Removing an SD card CAUTION: Make sure the SD card indicator is out before you remove the card or turn off the computer’s power.
Compact Flash 3. The SD card is designed so that it can be installed only one way. Do not try to force the card into the slot. 4. Do not leave an SD card partially inserted in the slot. Press the SD card until you hear it click into place. 5. Do not twist or bend SD cards. 6. Do not expose SD cards to liquids or store in humid areas or lay media close to containers of liquid 7. After using an SD card, return it to its case. 8. Do not touch the metal part or expose it to liquids or let it get dirty.
User’s Manual . OPTIONAL DEVICES COMPACT FLASH Figure 8-6 Inserting a Compact Flash module Removing a Compact Flash module To remove a Compact Flash, follow the steps below. 1. Right click (right button of the Touch Pad) on the Compact Flash drive’s icon and select eject from the pop-up menu. 2. Press the Compact Flash eject button to extend it. 3. Press the extended eject button to pop the compact Flash out slightly. 4. Pinch and pull out the Compact Flash. 5. Insert a dummy card into the slot.
Compact Flash COMPACT FLASH EJECT BUTTON .
User’s Manual Memory expansion This computer is equipped with two memory module sockets; Slot A beneath the keyboard and Slot B in the backside of the computer. You can increase the amount of RAM to 1024MB by installing an additional memory or replacing default memories with additional memories. NOTE: Observe the following instructions according to the model you purchased. • Install an additional memory module to Slot B for the computer with vacant Slot B.
Memory expansion NOTE: Use a 0-bit, Phillips screwdriver to remove and fasten screws. Use of an incorrect screwdriver can damage the screw heads. Removing and installing memory module in Slot A Follow the steps below to remove and install a memory module in Slot A. 1. RTurn the computer’s power off. Make sure the Power indicator is off. 2. Remove AC adaptor and all cables connected to the computer. 3.
User’s Manual OPTIONAL DEVICES 5. Remove two screws (right and left at the both right and left end of the keyboard) fixing the keyboard. Figure 8-10 Removing the keyboard (1) 6. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears.
Memory expansion 7. Raise the insulation sheet covering the memory module to appear the module.
User’s Manual OPTIONAL DEVICES 8. Push the latches to the outside to release the module. A spring will force one end of the module up. Figure 8-14 Removing the memory module 9. Pinch the module by the sides and pull it out. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 10. Insert a new module to the socket and push it downward to lie flat. Latches on either side will click into place to secure the module. 11.
Memory expansion Installing memory module in Slot B Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn off the power. 2. Remove all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-Up Modes.) 4. Remove one screw securing the memory module cover. 5. Slide your fingernail or a thin object under the cover and lift it off.
User’s Manual OPTIONAL DEVICES Figure 8-16 Inserting a module (1) Figure 8-17 Inserting a module (2) Figure 8-18 Inserting a module (3) 8-16
Memory expansion 8. Seat the cover and secure it with one screw. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes. 10. Turn the power on and make sure the added memory is recognized. Open System Properties in the Control Panel and click the General tab. NOTE: When you view the memory display, the total amount will be reduced by 16 MB, which is used for VRAM. Removing memory module in Slot B To remove the memory module, make sure the computer is in boot mode then: 1.
User’s Manual OPTIONAL DEVICES Figure 8-19 Removing the memory module 6. Set the cover and secure it with one screw and replace the battery pack. Battery Pack You can increase the portability of the computer with Battery Packs (PA3228U). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
USB FDD Kit USB FDD Kit The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 3. Turn the monitor’s power on. 4. Turn the computer on.
User’s Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. OPTIONAL DEVICES Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Chapter 9 Troubleshooting TROUBLESHOOTING Problem solving process .................................................................... 9-1 Preliminary checklist ........................................................................... 9-1 Analyzing the problem ........................................................................ 9-2 Hardware and system checklist ......................................................... 9-3 System start-up .............................................................
TROUBLESHOOTING
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the HW Setup program, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the DC IN indicator stops blinking. NOTE: It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN indicator stops blinking.
User's Manual Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer. Battery TROUBLESHOOTING If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes.
Hardware and system checklist Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes. If the Battery indicator glows after 20 minutes, let the battery continue to charge at least another 20 minutes before turning on the computer. If the indicator still does not glow, the battery may be at the end of its operating life. Replace it. If you do not think the battery is at the end of its operating life, see your dealer.
User's Manual Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software’s documentation.
Hardware and system checklist Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive. If a diskette is inserted, remove it and reboot. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk.
User's Manual Diskette drive For more information, refer to Chapter4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the external 3 1/2" diskette drive Try another diskette.
Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Pen (Stylus) Problem Procedure On-screen pointer does not respond to Pen operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. The Pen might be set unable to use. Press Fn + F9 keys to change Pen setting to enabled.
User's Manual 3. Adjust setting of each item of "Pen options" tab and click "OK". Touch Pad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab.
Hardware and system checklist USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3.
User's Manual PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. SD card TROUBLESHOOTING Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected.
Hardware and system checklist Compact Flash Refer also to Chapter 8, Optional Devices. Problem Procedure Compact Flash error occurs Reseat the Compact Flash to make sure it is firmly connected. Check the card’s documentation. You cannot read a file Make sure the target file is on the Compact Flash inserted in the slot. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
User's Manual Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. TROUBLESHOOTING USB Refer also to your USB device’s documentation.
Hardware and system checklist If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard. If these devices do not work, make sure the USB KB/Mouse Legacy Emulation item in HW Setup is set to Enabled. If problems persist, contact your dealer. Modem Refer to the online help files for Appendix C and D. Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct.
User's Manual Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval. Try lengthening this time interval. A CONNECT display is quickly replaced by NO CARRIER Check the error control setting in your communications application. You can also use the AT\N command. Refer to the online help files for Appendix C, AT Commands.
Hardware and system checklist LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. If problems persist, consult your LAN administrator. Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator.
User's Manual Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. TROUBLESHOOTING Make sure no optional Bluetooth PC card is installed in the computer.
TOSHIBA support TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system. It is important to investigate other sources of assistance first.
User's Manual TROUBLESHOOTING United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA InEurope Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.A. 7, Rue Ampère B.P. 131, 92804 Puteaux Cedex Netherlands TOSHIBA Information Systems, Benelux B.V.
Appendix A Specifications ..................................................................................... A-1 Appendix B Display Controller and Modes ...........................................................B-1 Appendix C AT Commands ....................................................................................C-1 Appendix D S-registers ........................................................................................... D-1 Appendix E V.90 ...............................................
APPENDIXES
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 289 (w) x 229 (d) x 14.9/19.1 (h) millimeters (does not include the thicker part of the bottom of the computer) Weight Hard disk Memory Display Kilograms 20GB 256 MB 12" XGA-TFT about 1.
APPENDIX A User's Manual Computer 15VDC 3.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.90 103/212A V.17/V.29/V.27ter /V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. The displays up to 1024 x 768 (XGA). The controller also supports simultaneous display on the internal LCD and on an external monitor.
User's Manual Video modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, consider the following points: APPENDIX B ❑ ❑ ❑ If your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Appendix B Table Video modes continued (Landscape) Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical D VGA Grph 320 x 200 Pixels 8x8 16 of 256K 16 of 256K 70Hz E VGA Grph 640 x 200 Pixels 8x8 16 of 256K 16 of 256K 70Hz F VGA Grph 640 x 350 Pixels 8 x 14 Mono Mono 70Hz 10 VGA Grph 640 x 350 Pixels 8 x 14 16 of 256K 16 of 256K 70Hz 11 VGA Grph VGA Grph 640 x 480 Pixels 640 x 480 Pixels 8 x 16 2 of 256K 2 of 256K 60Hz 8 x 16 16 o
User's Manual Table Video modes continued (Landscape) APPENDIX B Video mode B-4 Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical SVGA 640 x 480 Grph Pixels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 800 x 600 Grph Pixels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1024 x 768 Grph Pixels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1280 x 1024 Grph Pixels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1600 x 1200 Grph Pixels 64K of 64K 64K of 64K 60Hz SV
Appendix B Table Video modes (Portrait) Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical 0, 1 VGA Text 25 x 40 Characters 8x8 16 of 256K 16 of 256K 70Hz 2, 3 VGA Text 25 x 80 Characters 8x8 16 of 256K 16 of 256K 70Hz 0*, 1* VGA Text 25 x 40 Characters 8 x 14 16 of 256K 16 of 256K 70Hz 2*, 3* VGA Text 25 x 80 Characters 8 x 14 16 of 256K 16 of 256K 70Hz 0+, 1+ VGA Text 25 x 40 Characters 8(9) x 16 16 of 256K 16 of 256K 70Hz 2+,
User's Manual APPENDIX B Table Video modes continued (Portrait) Video mode Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical 12 VGA Grph 480 x 640 Pixels 8 x 16 16 of 256K 16 of 256K 60Hz 13 VGA Grph 200 x 320 Pixels 8x8 256 of 256K 256 of 256K 70Hz SVGA 480 x 640 Grph Pixels 256 of 256K 256 of 256K 60Hz 75Hz 85Hz SVGA 600 x 800 Grph Pixels 256 of 256K 256 of 256K 60Hz 75Hz 85Hz SVGA 768 x 1024 Grph Pixels 256 of 256K 256 of 256K 60Hz 75Hz
Appendix B Table Video modes continued (Portrait) Video mode Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical 64K of 64K 64K of 64K 60Hz SVGA 480 x 640 Grph Pixels 16M of 16M 16M of 16M 60Hz 75Hz 85Hz SVGA 600 x 800 Grph Pixels 16M of 16M 16M of 16M 60Hz 75Hz 85Hz SVGA 768 x 1024 Grph Pixels 16M of 16M 16M of 16M 60Hz 75Hz APPENDIX B SVGA 1200 x 1600 Grph Pixels B-7
APPENDIX B User's Manual B-8
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. For details on AT commands, refer to the online manual.
APPENDIX C User's Manual C-2
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. The contents of the registers are changed automatically when you modify corresponding settings in your communication software. If you choose, however, you can display and edit the contents of the registers manually when the modem is in command mode. For details on S-registers, refer to the online manual.
APPENDIX D User's Manual D-2
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. NOTE: V.
User's Manual Table E-1 Result codes for a V.90 connection No.
Appendix E AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX E User's Manual E-4
Wireless LAN In some markets, the computer is equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with the IEEE 802.11 Standard (Revision B). It supports data transfer up to 11 Mbit/s. It has Frequency Channel Selection (2.4 GHz) and allows roaming over multiple channels. For a description of Wireless LAN features and TOSHIBA Wireless LAN card specifications, refer to the online manual.
APPENDIX F User’s Manual F-2
Appendix G AC Power Cord and Connectors Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix H Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTIONS: 1. Do not remove the base cover except to remove or install the internal modem or to check the PTT label. 2. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. 4. Be careful not to drop any screws or other foreign matter into the computer. Metal or other foreign matter can damage the computer.
User’s Manual Removing the internal modem To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC Adaptor and any other peripheral devices. 3. Turn the computer upside down. 4. Remove the battery. 5. Remove one screw securing the modem socket cover. 6. Lift off the modem socket cover. 7. Remove two screws securing the modem board. Store the screws in a safe place. Be careful not to lose them APPENDIX H 8. Disconnect the modem board and lift it out. 9.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD and communication devices.
I-2 P1330 12"TFT-XGA LCD 12TX 384M 512M 512M 640M 768M 1024M 512MB 512MB+128MB 512MB+256MB 512MB+512MB 256M 256MB 256MB+256MB 256M 128MB+128MB 256MB+128M 128M 128MB Memory 60G 40G 30G 20G HDD 60 40 30 20 Wireless LAN /Bluetooth Bluetooth Wireless LAN BT WL WL/BT Communication * Figures indicate the CPU operating speed in megahertz. For example, P1330 means Mobile Intel® Pentium® III processor 1.33 GHz-M .
The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
GLOSSARY adaptor (Abbreviations continued) VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices.
cache memory backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. See also AUTOEXEC.BAT. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on.
GLOSSARY capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. card: Synonym for board. See board. CardBus: An industry standard bus for 32-bit PC Cards. CD-ROM: A Compact Disk-Read Only Memory is a high capacity disk that can be read from but not written to.
disk drive controller: Built-in hardware and software that controls the functions of a specific internal or peripheral device (e.g. keyboard controller). co-processor: A circuit built into the processor that is dedicated to intensive math calculations. CPS: Characters per second. Typically used to indicate the transmission speed of a printer. CPU: Central processing unit. The portion of the computer that interprets and executes instructions. CRT: Cathode Ray Tube.
GLOSSARY disk storage disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record. diskette: A removable disk that stores magnetically encoded data used on a microcomputer. Also called floppy disk. display: A CRT, plasma screen, LCD, or other image producing device used to view computer output. documentation: The set of manual and/or other instructions written for the users of a computer system or application.
hotkey floppy disk drive (FDD): An electromechanical device that reads and writes to floppy disks. See also diskette. Fn-esse: A TOSHIBA utility that lets you assign functions to hotkeys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
GLOSSARY HW Setup HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can manipulate. infrared port: A cableless communications capable of using infrared signals to send serial data.
monitor M main board: See motherboard. L . level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing-side coating is etched into character forming segments with leads that extend to the edge of the glass.
GLOSSARY motherboard motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board. N non-system disk: A formatted diskette (floppy disk) you can use to store programs and data but you cannot use to start the computer. See system disk.
Radio frequency interference (RFI) shield parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique string of characters used to identify a specific user.
GLOSSARY Random Access Memory (RAM) Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to. restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. RGB: Red, green, and blue.
write protection terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT: A color LCD technology that applies individual transistors to each pixel enabling fine display control and excellent screen legibility. TOSHIBA Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. Touch pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic.
GLOSSARY Glossary-14
Index D AC adaptor 1-4, 2-10 DC IN 15V port 2-4 connecting 3-6 universal 1-10, 8-10 ASCII characters 5-9 Auto power on, See Power DC IN indicator 2-8, 6-4 Disk indicator 2-8 Diskette care 4-4 Display 1-3, 2-6, See also Video modes and Monitor external automatic power off 1-6 controller 1-3, Appendix B driver 1-9 hinge 2-6 opening 3-5 selection, See Hot keys Documentation list 1-2 B Battery, See also Battery Pack charging 6-8 extending life 6-11 indicator 2-8, 6-4 lock 2-6, 6-12 monitoring capacity 6-9 re
INDEX User's Manual Fn + Esc (sound mute) 5-4 Fn-esse 1-8 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-5 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-6 Fn + F7 (display brightness) 5-6 Fn + F10 (arrow mode) 5-3, 5-7 Fn + F11 (numeric mode) 5-3, 5-8 Fn + F12 (ScrLock) 5-3 Fn Sticky key 5-6 Function Keys 5-2 H Hard disk drive 1-3 automatic power off 1-6 problems 9-9 Hibernation 1-7, 5-5 Hotkeys 1-6, 5-4 display brightness 5-6 di
Index M N Numeric keypad, See Keypad overlay O Operating system, See Windows Overlay, See Keypad overlay P Panel power on/off, See Power Password power on 1-7 starting the computer with 6-14 supervisor 1-8, 7-9 user 7-4 PC card 1-5 installing 8-2 location of slots 2-3 problems 9-13 removing 8-4 Index-3 INDEX Main battery, See Battery Pack Memory 1-3 expansion 1-10, 8-6 installing 8-7 removing 8-9 slots 1-3 Microphone, See sound system, microphone Microprocessor, See Processor Modem 1-5, 4-10 connecti
User's Manual USB mouse 9-12 Wireless LAN 9-17 Processor 1-3 R Real time clock battery, See Battery Recovery CD-ROM 3-13 INDEX S Screen, See Display ScrLock (Fn + F12), See Soft keys SD card 1-5 indicator 2-2 installing 8-5 location of slot 2-2 problems 9-13 removing 8-6 Security lock 1-10 attaching 8-13 location 2-2 Self Test, See Problems Sensor switch 2-6 Slim Port Replicator 1-10, 8-11 Soft keys 5-2 cursor control mode 5-3 Enter 5-3 numeric mode 5-3 right Alt key 5-3 right Ctrl key 5-3 ScrLock 5-3 So
