User Manual

ManualsBrandsToshiba Client Solutions ManualsElectronicsLibretto

1. PRODUCT SPECIFICATIONS

Specifications for Wireless LAN Functions

Physical specifications

Power save (doze) mode 45 mA

Receive mode 250 mA

Send mode 350 mA

Power 3.3 V

Wireless features

The wireless features of the wireless LAN vary depending on the product you purchase and the

country you are in when you purchase it.

I many cases, the wireless transmission are based on the wireless regulations of the country

where it is being used. Wireless network equipment is designed to use 2.4 GHz bandwidth to

operate which does not require a wireless license. However, depending on the national wireless

regulations, there may be several restrictions on the use of wireless network equipment.

NOTE: • See the “Users Announcement” for information on the appropriate wireless

regulations for each country.

Wireless frequency range 2.4 GHz (2400 to 2483.5 MHz)

Modulator

Direct diffusion format

CCK (Forwarding rate; High, Medium)

DQPSK (Forwarding rate; Standard)

DBPSK (Forwarding rate; Low)

Diffusion format 11 chip Barker Sequence

Bit error rate (BER) 10

–5

or greater

Rated output 15 dBm

Forwarding rate

High Speed

11 Mb/s

Medium

Speed

5.5 Mb/s

Standard

Speed

2 Mb/s

Low Speed

1 Mb/s

Reception speed –83 dBm –87 dBm –91 dBm –94 dBm

Diffusion delay

(FER 1% or less)

65 ns 225 ns 400 ns 500 ns

There is a correlation function of transmission range and forwarding rate for wireless equipment.

The lower the wireless transmission forwarding rate the broader the transmission range.

TIPS: • Metal surfaces or dense solid bodies that are placed close to the antenna will exert

an effect on the transmission range of the wireless device.

• Also, if something that absorbs or reflects the wireless signal is in the path of the

wireless signal, the transmission range will be effected.

Summary of content (22 pages)

PAGE 1
. PRODUCT SPECIFICATIONS Specifications for Wireless LAN Functions ! Physical specifications Power save (doze) mode 45 mA Receive mode 250 mA Send mode 350 mA Power 3.3 V ! Wireless features The wireless features of the wireless LAN vary depending on the product you purchase and the country you are in when you purchase it. I many cases, the wireless transmission are based on the wireless regulations of the country where it is being used. Wireless network equipment is designed to use 2.
PAGE 2
! Supported frequency bands The 2.4 GHz channels that the wireless LAN supports, vary depending on the applicable national wireless regulations (See the “Wireless IEEE802.11” chart). See the “Users Announcement” for information on the appropriate wireless regulations for each country. Wireless IEEE802.11 Channel Set Frequency band 2400 to 2483.
PAGE 3
Exterior Dimension Diagram * These measurements do not include protrusions.
PAGE 4
Supported Video Mode The regulations that determine the maximum possible number of colors and screen resolution that is controlled by the display controller is called the video mode. All the video modes that this product supports in English mode are shown below. Usually the mode number is used by the programmer to differentiate between the various modes. When application software specifies a mode based on the mode number, that number may not match the number in the diagram.
PAGE 5
Hardware Resources You can confirm the memory map, I/O port map and resources that use IRQ and DMA in the following way. There are modifications depending upon the environment (hardware/software) that is being used. 1. Click [Start], [All programs], [Accessories], [System tools] and [System information]. 2. Double click on [Hardware resource] in the tree on the left side of the screen. 3. Click the items that you want to confirm.
PAGE 6
2.
PAGE 7
USB Interface Pin Number Signal name 1 VCC +5V 2 –Data Minus data I/O 3 +Data Plus data I/O 4 GND Signal ground Explanation Signal Direction Connector diagram Signal name: A minus (–) is attached to signals that are negative logic values. Signal direction (I): Input to the personal computer. Signal direction (O): Output from the personal computer.
PAGE 8
LAN Interface Pin Number Signal name 1 TX Transmission data (+) O 2 –TX Transmission data (–) O 3 RX Reception data (+) I 4 Unused Not in use 5 Unused Not in use 6 –RX 7 Unused Not in use 8 Unused Not in use Explanation Reception data (–) Signal Direction I Connector diagram Signal name: A minus (–) is attached to signals that are negative logic values. Signal direction (I): Input to the personal computer. Signal direction (O): Output from the personal computer.
PAGE 9
3. TECHNICAL STANDARD COMPLIANCE Self Regulation of Leakage Current This equipment complies with the international standard for personal computers (PC-11-1988) determined by the Japan Electronics and Information Technology Industries Association. Instantaneous Drop in Voltage This equipment satisfies the guidelines for personal computer instantaneous drop in voltage countermeasures determined by the Japan Electronics and Information Technology Industries Association.
PAGE 10
FCC Information Product name Model number : Libretto L5/080TN : PAL5080TN FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 11
5.0 cm must be maintained between the user and the antenna(s) to ensure exposure compliance. Contact Address : Telephone : TOSHIBA America Information Systems, Inc.
PAGE 12
Cautions When Using the Modem When using the internal modem in this product, take the following precautions. The internal modem complies with the Japan Approvals Institute for Telecommunications Equipment regulation 50 item 1 for technical standard compliance. • Compliance number A00-0940JP Regions where the modem can be used The internal modem in your computer can be used in the following countries and regions: Iceland, Ireland, U.S.A, U.A.E, U.K.
PAGE 13
Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
PAGE 14
Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: - The telephone number of the line to which you will connect the modem - The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.
PAGE 15
Disconnection If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
PAGE 16
Instructions for IC CS-03 Certified Equipment 1. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
PAGE 17
Notes for Users in Australia and New Zealand Modem Warning Notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
PAGE 18
- Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
PAGE 19
- The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. - It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
PAGE 20
TROUBLE CHECKLIST Contact Toshiba PC Dial for information about operating your personal computer. TOSHIBA PC DIAL Technical questions can be answered on the telephone. * Hours: 9:00 to 19:00 (except for holidays and from December 31 to January 3) Navi-Dial National Common Telephone Number [Be careful to dial the correct telephone number to avoid making mistakes.
PAGE 21
Trouble Checklist For smoother response, check the following details before contacting Toshiba. If Toshiba PC Dial asks you for information other than the following, such as the operating system version and the type of CPU, check this information by clicking the [Basic Information Display] button in [PC Diagnostic Tool]. [Regarding the environment you are using (the personal computer environment that you are currently using).] Q .
PAGE 22
Q .6 How frequently do the symptoms occur? # They occurred only once and did not occur again. # They occur until the power is cut, but do not occur when restarting after cutting the power. # They always occur when restarting after cutting the power. # Others: Q .7 Do the symptoms occur after a particular operation? # They occur after a specific operation. # They occur after any operation. # Others: Q .8 For consultation about the Internet and transmissions.