user manual

ManualsBrandsToro ManualsSnow BlowerSnow Blower 38272

FormNo.3369-487RevB

PowerClear418ZR/ZESnowthrower

ModelNo.38272—SerialNo.312000001andUp

ModelNo.38282—SerialNo.312000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedprimarilyforremoving

snowfrompavedsurfaces,suchasdriveways

andsidewalks,andothersurfacesfortrafcon

residentialorcommercialproperties.Itisnot

designedforremovingmaterialsotherthansnow,

norisitdesignedforclearingoffgravelsurfaces.

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoidinjury

andproductdamage.Youareresponsibleforoperating

theproductproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

productandaccessoryinformation,helpndingadealer,

ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,

oradditionalinformation,contactanAuthorized

ServiceDealerorToroCustomerServiceandhave

themodelandserialnumbersofyourproductready.

Figure1identiesthelocationofthemodelandserial

numbersontheproduct.Writethenumbersinthe

spaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjury

ordeathifyoudonotfollowtherecommended

precautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Safety

ThismachinemeetsorexceedstheB71.3

specicationsoftheAmericanNationalStandards

Instituteineffectatthetimeofproduction.

Readandunderstandthecontentsofthismanual

beforeyoustarttheengine.

Thisisthesafetyalertsymbol.Itisusedtoalert

youtopotentialpersonalinjuryhazards.Obeyall

safetymessagesthatfollowthissymboltoavoid

possibleinjuryordeath.

Improperlyusingormaintainingthismachine

couldresultininjuryordeath.Toreducethis

potential,complywiththefollowingsafety

instructions.

Thismachineiscapableofinjuringhandsandfeet

andofthrowingobjects.Failuretoobservethe

followingsafetyinstructionscouldresultinserious

injury.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (20 pages)

PAGE 1
Form No. 3369-487 Rev B Power Clear 418 ZR/ZE Snowthrower Model No. 38272—Serial No. 312000001 and Up Model No. 38282—Serial No. 312000001 and Up Operator's Manual Introduction Model No. This machine is intended to be used by residential homeowners. It is designed primarily for removing snow from paved surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
PAGE 2
Training • Do not attempt to clear snow from a gravel or crushed rock surface. This product is intended for use only on paved surfaces. • Read, understand, and follow all instructions on the machine and in the manual(s) before operating this machine. Be thoroughly familiar with the controls and the proper use of the machine. Know how to stop the machine and disengage the controls quickly.
PAGE 3
• Disengage power to the rotor blades when machine is transported or not in use. • Before adjusting, cleaning, repairing, and inspecting the machine, and before unclogging the discharge chute, stop the engine, remove the key, and wait for all moving parts to stop. • Never operate the machine without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run. • Never touch a hot engine or muffler.
PAGE 4
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 120-0149 1. Primer 2. Push the primer two times to prime the engine. 117-6047 1. Cutting dismemberment, impeller and cutting dismemberment, auger hazards—do not place your hand in the chute; remove the ignition key and read the instructions before servicing or performing maintenance. 3. Push key in to switch engine On. 4. Pull key to switch engine switch Off. 5.
PAGE 5
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 Oval-head bolts Curved washers Handle knobs 2 2 2 Install the handle. 2 No parts required – Install the recoil starter handle. 3 Discharge chute assembly Screws Washers Locknuts Knob 1 2 2 2 1 Install the discharge chute assembly. Bottle of engine oil 1 Fill the engine with oil. No parts required – Adjust the control cable.
PAGE 6
2 Installing the Recoil Starter Handle No Parts Required Figure 5 Procedure 1. Knob Install the recoil starter handle in the rope guide as shown in Figure 4. 2. Bolt (2), washer (2), and locknut (2) Note: Install the bolts from the inside of discharge chute assembly so that the washers and locknuts are on the outside of the chute. Important: Do not overtighten the locknuts. 4 Figure 4 Filling the Engine with Oil 1.
PAGE 7
oil, remove the excess oil as directed in Changing the Engine Oil. Note: You may tip the machine forward (handle up) a little to make adding oil easier. Remember to return the machine to the operating position before checking the oil level. Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 5. Screw the oil fill cap into the oil fill hole and hand tighten it securely. Figure 6 5 1. Move the machine to a level surface. Adjusting the Control Cable 2.
PAGE 8
Product Overview Note: Ensure that a gap of 1/16 to 1/8 inch (2 to 3 mm) exists between the control bar and the handle (Figure 8). Important: The control cable must contain some slack when you disengage the control bar for the rotor blades to stop properly. Adjusting the Control Cable 1. Slide up the spring cover and unhook the spring from the adjuster link (Figure 9). Figure 10 Figure 9 1. Adjuster link 3. Spring cover 2. Z-fitting 4. Unhook the spring here. 1. Control bar 6.
PAGE 9
Operation you may add fuel stabilizer to newly purchased gasoline to keep it fresh for up to 6 months. Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine Oil Level Service Interval: Before each use or daily—Check the engine oil level and add oil if necessary. 1. Ensure that the fuel tank is not overfilled (refer to Figure 12) and that the fuel cap is securely in place. 2. Move the machine to a level surface. 3.
PAGE 10
Starting the Engine Important: Do not tip the machine all the way forward onto its nose, or fuel may leak out of the machine. 1. Push the ignition key fully inward to the On position (Figure 15). Max fill: 12 oz. (0.35 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 14 to select the best oil viscosity for the outdoor temperature range expected: Figure 15 1. Ignition key 2. Move the choke lever fully to the right (Figure 16).
PAGE 11
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before plugging it into a power source. If the cord is damaged, do not use it to start the machine. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance. Figure 17 Note: Remove your glove when you push in the primer so that air cannot escape from the primer hole.
PAGE 12
Engaging the Rotor Blades To engage the rotor blades, hold the control bar against the handle (Figure 20). Figure 22 1. Ignition key Figure 20 Adjusting the Discharge Chute and Chute Deflector 1. Control bar To adjust the discharge chute, move the chute handle as shown in Figure 23. Disengaging the Rotor Blades To disengage the rotor blades, release the control bar (Figure 21). Figure 23 1.
PAGE 13
Note: By slightly varying lifting force on the handle, you can control the forward speed of the machine. In heavy snow, push forward on the handle, if necessary, but let the machine work at its own pace. Do not lift the handle any more than necessary, because the scraper will lift off the ground and snow will escape behind the machine. Preventing Freeze-up after Use • Let the engine run for a few minutes to prevent moving parts from freezing.
PAGE 14
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval After the first hour After the first 2 hours Before each use or daily Yearly Yearly or before storage Maintenance Procedure • Check the control cable and adjust it if necessary. • Check for loose fasteners and tighten them if necessary. • Change the engine oil. • Check the engine oil level and add oil if necessary.
PAGE 15
3. Place an oil drain pan under the oil drain plug (Figure 11), remove the oil drain plug, and tip the machine backward (handle down) halfway to the ground to drain the used oil into the oil drain pan. Max fill: 12 oz. (0.35 l), type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 28 to select the best oil viscosity for the outdoor temperature range expected: Important: Do not tip the machine all the way back to the ground, or fuel may leak out of the machine.
PAGE 16
Figure 29 1. Center electrode insulator 3. Air gap (not to scale) 2. Side electrode Figure 31 6. Install the spark plug and torque it to 20–22 ft-lb (27–30 N-m). 1. Rotor pulley 5. Idler pulley 2. Idler arm brake 6. Engine pulley 7. Connect the wire to the spark plug. 3. Drive belt 4. Idler arm 7. Tabs on the idler arm Replacing the Drive Belt 3. Press down on the idler arm and remove the belt from between the tab on the idler arm brake and the rotor pulley.
PAGE 17
Important: Ensure that you install the drive belt so that it sits above the two tabs on the idler arm and below the idler arm brake (Figure 31). 7. Install the drive belt cover with the fasteners that you removed in step 1. Storage Storing the Machine WARNING • Gasoline fumes are highly flammable, explosive, and dangerous if inhaled. If you store the product in an area with an open flame, the gasoline fumes may ignite and cause an explosion. Figure 33 1. Carburetor bowl bolt—do not remove 2.
PAGE 18
Notes: 18
PAGE 19
Federal Emission Control Warranty Statement A Two-Year Limited Warranty Your Warranty Rights and Obligations The U.S. Environmental Protection Agency (EPA), The Toro Company, and its affiliate, Toro Warranty Company, are pleased to explain the emission control system warranty on your 2009 and later utility/lawn/garden equipment engine. 2009 and later model year utility/lawn/garden equipment engines must be designed, built and equipped, at the time of sale, to meet the U.S.
PAGE 20
The Toro Total Coverage Guarantee A Two-Year Full Warranty (45 Day Limited Warranty for Commercial Use) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if used for residential purposes*, if defective in materials or workmanship or if it stops functioning due to the failure of a component for the period listed below.