Use and Care Manual

ManualsBrandsToro ManualsLawn Mower BagsTimeCutter Twin Bagger for 60 in. Fabricated Deck (2020 and Newer)

FormNo.3413-338RevB

60inBaggerKit

TimeCutter

MX6050RidingMower

ModelNo.79396—SerialNo.400000000andUp

Operator'sManual

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Introduction

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Wheneveryouneedservice,genuineparts,or

additionalinformation,contactanAuthorizedService

DealerorCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

g005673

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafety-alertsymbol

(Figure2),whichsignalsahazardthatmaycause

seriousinjuryordeathifyoudonotfollowthe

recommendedprecautions.

g000502

Figure2

1.Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3413-338*B

Summary of content (20 pages)

PAGE 1
Form No. 3413-338 Rev B 60in Bagger Kit TimeCutter® MX 6050 Riding Mower Model No. 79396—Serial No. 400000000 and Up Operator's Manual WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage.
PAGE 2
Contents Introduction ............................................................... 1 Safety ....................................................................... 3 Towing Safety ..................................................... 3 Safety and Instructional Decals .......................... 4 Setup ........................................................................ 5 1 Preparing the Machine..................................... 6 2 Installing the Weight.........................................
PAGE 3
Safety • Do not leave grass in grass catcher for extended periods of time. • Grass catcher components are subject to wear, WARNING damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace them with manufacturer's recommended parts when necessary. Leaves, grass, or brush can catch fire. A fire in the engine area can cause personal injury and property damage. • Keep the engine and muffler area free of debris accumulation.
PAGE 4
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal109-6809 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. Do not remove the bagger top when it is closed; open the bagger top and then remove it. decal131-4036 131-4036 1.
PAGE 5
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 Description Use Qty.
PAGE 6
Note: Determine the left and right sides of the machine from the normal operating position. 2 1 Installing the Weight Preparing the Machine Parts needed for this procedure: 1 Weight tray 1 Left weight-tray mount 1 Right weight-tray mount 1 Suitcase weight—16 kg (35 lb) 1. Park the machine on a level surface and disengage the drives. 1 Retaining rod 2 Bolt (3/8 x 1-1/4 inches) 2. Engage the parking brake. 4 Flange nut (3/8 inch) 3. Shut off the engine and remove the key.
PAGE 7
g196533 Figure 3 Cutaway view g196560 Figure 5 1. Weight-tray mounts 3. Flange nut (3/8 inch) 1. Retaining rod 2. Bolt (3/8 x 1-1/4 inches) 4. Self-tapping bolt (5/16 x 3/4 inch) 2. Weight tray 5. Insert the retaining rod into the tray and rotate it into the locked position (Figure 5). 3. Use the 2 carriage bolts (3/8 x 1 inch) and flange nuts to secure the weight tray to the mounts (Figure 4). Important: Remove the suitcase weight whenever you remove the bagger attachment. g196549 Figure 4 1.
PAGE 8
frame to the machine frame using 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch). 3 Installing the Attachment Mount Parts needed for this procedure: 1 Stabilizer bracket 2 Carriage bolt (5/16 x 3/4 inch) 4 Locknut (5/16 inch) 2 Self-tapping screw (5/16 x 3/4 inch) 2 Bolt (5/16 x 1 inch) 1 Pivot frame 1. Machine frame 4. Bolt (5/16 x 1 inch) 2 Hairpin cotter 2. Locknut (5/16 inch) 5. Pivot frame 2 Rod 3. Hole 2 Washer 1 Draw-bar decal g203563 Figure 7 3.
PAGE 9
4 Installing the Latch Rod Parts needed for this procedure: g203562 1 Latch rod 1 Hairpin cotter Figure 9 Procedure 1. Draw bar decal Install the latch rod with a hairpin cotter (Figure 11). 6. Install the bent, flared end of a rod into the keyed slot in the left side of the machine frame, and move the rod rearward to seat it in the frame (Figure 10). Note: Repeat this step for the right side of the machine. g202360 Figure 11 g203565 Figure 10 Left side shown 1. Pivot frame hole 4.
PAGE 10
Note: Make sure that the screens snap into place and the tabs engage the bagger top. 6 Installing the Bagger Top 1 Parts needed for this procedure: 2 2 Grass Bag 1 Upper bagger tube Procedure 1. Install the bagger top to the bagger frame. 2. Slide the brackets over the posts in the bagger frame and install the circular cotter pin into the hole in the right hand post (Figure 13). 3. Rotate the bagger hood down to the operating position.
PAGE 11
4. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 14). 7 1 Installing the High-Lift Blades Parts needed for this procedure: 3 2 High-lift blade Procedure 4 Refer to the Operator’s Manual for the machine to remove the existing blades and install the high-lift blades. 3 8 g033032 Figure 14 1. Bag 3. Retaining bracket 2. Bagger frame 4. Bag frame hook Installing the Chute Parts needed for this procedure: 5.
PAGE 12
3 2 1 4 5 G013095 g013095 Figure 16 1. Deflector assembly 4. Carriage bolt (existing; reuse) 2. Locknut (existing; retain) 5. Carriage bolt (existing; retain) g202281 Figure 17 6. High-lift blade 3. Locknut (existing; reuse) 1. Hole in front wall of the mower deck 2. Locknut 8. Angled cutoff baffle 2. Remove the deflector assembly. 3. Horizontal post, curved baffle 4. Vertical post, curved baffle Note: Retain all parts to convert the mower deck to side discharge. 5. Curved baffle 3.
PAGE 13
1 9 G013097 2 Connecting with the Discharge Tube 3 4 Parts needed for this procedure: 1 5 Discharge tube Procedure 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 20). 6 2 1 G010641 g013097 Figure 18 1. Discharge chute 4. Folded metal bracket (chute) 2. Hand knob 5. Forward vertical plate (deck) 3. Washer 6. Exposed post in the mower deck (curved baffle) 3 5 6.
PAGE 14
Operation 5. Install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 22). 1 Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. • Never remove the discharge tube, bags, bagger top, or the chute while the engine is running.
PAGE 15
8. After you remove the obstruction, install the complete bagger system and resume operation. Removing the Bagger CAUTION Failing to remove the front bagger weights and operating the machine without the bagger attachment may cause an unstable condition, which could result in a loss of control. • Always remove the front weights when removing the bagger attachment. g203567 Figure 23 • Never operate the machine without the bagger attachment and the front weights installed. 1.
PAGE 16
Operating Tips CAUTION As the bagger fills, extra weight is added to the back of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. Tips for Bagging Remembering the Size of the Machine with the Attachment • Do not start or stop suddenly when going uphill or downhill. Avoid uphill starts. Remember that the machine is longer and wider with this attachment installed. By turning too sharply in confined places, you may damage the attachment.
PAGE 17
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. CAUTION DANGER If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Leaves, grass, or brush can catch fire. A fire in the engine area can cause personal injury and property damage. Remove the key from the ignition and disconnect the wire from the spark plug before you do any maintenance.
PAGE 18
Inspecting the Mower Blades Storage Storing the Bagger Attachment Inspect the mower blades regularly and whenever a blade strikes a foreign object. If the blades are badly worn or damaged, install new blades. Refer to your mower or mower Operator's Manual for complete blade maintenance. Note: To prevent rapid deterioration of the bag material, store the bags where they will dry completely after each use. 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment (page 18).
PAGE 19
Notes:
PAGE 20
TimeCutter The Toro Warranty Limited Warranty (see warranty periods below) Conditions and Products Covered 3. If for any reason you are dissatisfied with the Service Dealer’s analysis or with the assistance provided, contact us at: The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Products listed below if defective in materials or workmanship.