Use and Care Manual

ManualsBrandsToro ManualsMulching & StripingTimeCutter 50 in. Recycler Kit

FormNo.3367-646RevA

50inRecycler

Kit

2007andAfterRidingMower

ModelNo.79019

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Nopartsrequired

–

Removetheblades.

Leftbafe

Rightbafe

Knob4

Curvedwasher

Installthebafes.

Kickerplate3

Phillipsheadscrew(#8x5/8inch)

Installthekickerplates.

Recyclingdecal1Installthedecal.

Recyclingmowerblade3Installthebladesandmower.

PreparingtheMower

NoPartsRequired

Procedure

1.Stoptheengineandremovetheignitionkey.

2.RemovethemowerasdescribedinyourOperator’s

Manual.

3.Turnthemowerupsidedown.

4.Somemodelshaveacut-offbafelocatednearthe

dischargeopening(Figure1).Removethebafeifit

ispresent.Retainthepartsforfutureuse.

Figure1

1.Cut-offbafe

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3367-646 Rev A 50in Recycler® Kit 2007 and After Riding Mower Model No. 79019 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Prepare the mower. No parts required – Remove the blades. Left baffle Right baffle Knob Curved washer Kicker plate Phillips head screw (#8 x 5/8 inch) 1 1 4 4 3 6 Recycling decal 1 Install the decal.
PAGE 2
3 Removing the Blades Installing the Baffles No Parts Required Parts needed for this procedure: Procedure 1. Choose the style of blade, of those shown in Figure 2 and Figure 3, that best matches the blades on your mower. Hold the blade end using a rag or thickly-padded glove and remove the blade as shown. 1 Left baffle 1 Right baffle 4 Knob 4 Curved washer Procedure 1.
PAGE 3
Figure 5 1. Knob 3. Baffle stud coming through the mower 2. Curved washer 3. Slide the right baffle through the discharge opening and secure it using 2 knobs and curved washers (cupped side facing the mower) as shown in Figure 4 and Figure 5. Important: Ensure that the tab on the far right side of the right baffle is outside of the mower and is flush with the mower wall. 4 Installing the Kicker Plates Parts needed for this procedure: 3 Kicker plate 6 Phillips head screw (#8 x 5/8 inch) Procedure 1.
PAGE 4
Figure 7 1. Recycler decal 2. Left side of mower 6 Installing the Blades and Mower Figure 6 1. Mower deck Parts needed for this procedure: 2. Kicker plate, installed 3 2. If there are rivets blocking the mounting holes in the mower, drill out the center of each rivet with a 3/16 inch (5 mm) drill bit and discard the rivet. Recycling mower blade Procedure 1. Install the blade onto the spindle shaft (Figure 8). 3. Secure the plates to the deck using six Phillips head screws (#8 x 5/8 inch).
PAGE 5
Operation 3. Torque the blade bolt to 35-65 ft-lb (47-88 N-m). 4. Install the mower as described in your Operator’s Manual. Converting to Side-discharge Operation DANGER Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death.
PAGE 6
setting another notch or convert to side discharge or bagging operations. Mowing in Extreme Conditions Air is required to cut and recut grass clippings in the mower housing, so do not set the height-of-cut too low or totally surround the housing by uncut grass. Always have one side of the mower housing free from uncut grass, allowing air to be drawn into housing. When making an initial cut through the center of the uncut area, operate the machine at a slower speed and back up if the mower starts to clog.
PAGE 7
Notes: 7
PAGE 8