Use and Care Manual

ManualsBrandsToro ManualsMulching & StripingTimeCutter SS 32 in. Recycler kit

FormNo.3367-626RevA

32inRecycler

Kit

2011andAfterTimeCutter

ZRidingMower

ModelNo.79017

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Kickerplate4

Bolt(5/16x3/4inch)

Bolt(5/16x1-1/4inches)

Locknut(5/16inch)

Installthekickerplates.

Deckring4

Bolt(5/16x3/4inch)

Locknut(5/16inch)

Installthedeckring

Dischargecover1

Wingnut1

Installthedischargecover.

Recyclingdecal1Instalthedecal.

PreparingtheMower

NoPartsRequired

Procedure

1.Stoptheengineandremovetheignitionkey.

2.Removethecuttingdeckasdescribedinyour

Operator’sManual.

3.Turnthemowerupsidedown.

4.Removethelocknutsandboltsecuringthecutoff

bafetotheundersideofthedeck(Figure1).Retain

allpartsandfasteners.

G015220

Figure1

1.Pivotrod

4.Nut(5/16inch)

2.Bolt

5.Locknut(3/8inch)

3.Cutoffbafe(existing)

5.Replacethelocknutontothepivotrod.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3367-626 Rev A 32in Recycler® Kit 2011 and After TimeCutter® Z Riding Mower Model No. 79017 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description No parts required – Kicker plate Bolt (5/16 x 3/4 inch) Bolt (5/16 x 1-1/4 inches) Lock nut (5/16 inch) Deck ring Bolt (5/16 x 3/4 inch) Lock nut (5/16 inch) Discharge cover Wing nut 4 7 1 8 4 8 8 1 1 Recycling decal 1 1 Use Qty.
PAGE 2
3 Installing the Kicker Plates Installing the Deck Ring Parts needed for this procedure: Parts needed for this procedure: 4 Kicker plate 4 Deck ring 7 Bolt (5/16 x 3/4 inch) 8 Bolt (5/16 x 3/4 inch) 1 Bolt (5/16 x 1-1/4 inches) 8 Lock nut (5/16 inch) 8 Lock nut (5/16 inch) Procedure Procedure 1. Install the interlocking deck rings to the bottom of the mower (Figure 3). 1. Align the three kicker plates as shown in Figure 2.
PAGE 3
4 5 Installing the Discharge Cover Installing the Decal Parts needed for this procedure: Parts needed for this procedure: 1 Discharge cover 1 Wing nut 1 Recycling decal Procedure Procedure Install the decal on left side of the mower (Figure 5). 1. Lift the grass deflector and place the discharge cover over the opening onto the lower lip of the mower and slide it into the front hinge (Figure 4). Figure 5 1. Recycler decal Figure 4 1. Grass deflector 2. Discharge cover 3. Lower lip 4.
PAGE 4
Operation Converting Back to Side Discharge DANGER Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death. • Never remove the grass deflector from the mower because the grass deflector routes material down toward the turf. If the grass deflector is ever damaged, replace it immediately. Figure 6 1. Grass deflector 2.
PAGE 5
making an initial cut through the center of the uncut area, operate the machine at a slower speed and back up if the mower starts to clog. Mowing at the Proper Intervals Under normal conditions you’ll need to mow every 4-5 days. However, grass grows at different rates at different times. Thus, in order to maintain the same height-of-cut, which is a good practice, you’ll need to cut more frequently in early spring; as the grass growth rate slows in mid summer, cut only every 8-10 days.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8