Installation Guide

ManualsBrandsToro ManualsOutdoor Power EquipmentTimeCutter HD Fab 54 in. 24.5 HP V-Twin Gas Riding Zero Turn Mower with Smart Speed with Roll-Over Protection Option

FormNo.3416-766RevB

Roll-OverProtectionSystemKit

TimeCutter

HDZero-Turn-RadiusRidingMower

ModelNo.136-7495

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Safety

RolloverProtectionSystem

(ROPS)Safety

•Donotremovetherollbarfromthemachine.

•Ensurethattheseatbeltisattachedandthatyou

canreleaseitquicklyinanemergency.

•Alwayswearyourseatbeltwhentherollbarisup.

•Checkcarefullyforoverheadobstructionsanddo

notcontactthem.

•Keeptherollbarinsafeoperatingconditionby

thoroughlyinspectingitperiodicallyfordamage

andkeepingallthemountingfastenerstight.

•Replaceadamagedrollbar.Donotrepairoralter

it.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Leftlowerrollbar

Rightlowerrollbar1

Bolt(1/2x4inches)

Washer6

Locknut(1/2inch)

Leftsupportbracket

Rightsupportbracket1

Bolt(1/2x1-1/4inches)

Bolt(1/2x1-3/4inches)

Installthelowertubesandseatbelt.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3416-766*B

Summary of content (8 pages)

PAGE 1
Form No. 3416-766 Rev B Roll-Over Protection System Kit TimeCutter® HD Zero-Turn-Radius Riding Mower Model No. 136-7495 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Rollover Protection System (ROPS) Safety • Do not remove the roll bar from the machine. • Ensure that the seat belt is attached and that you can release it quickly in an emergency.
PAGE 2
Procedure 3 4 Description Use Qty. Left seat-belt bracket (machines without MyRide only) Right seat-belt bracket (machines without MyRide only) Seat-belt assembly Seat-belt buckle Bolt (1/2 x 1-1/4 inches) Locknut (1/2 inch) Self-tapping screw (1/4 x 5/8 inch) Roll bar Side plate Bolt (1/2 x 3 inches) Flat spacer Washer Locknut (1/2 inch) Bumper Cylindrical spacer Lanyard with pivot pin, washer, and hairpin cotter 1 1 1 1 4 4 2 1 4 8 4 6 8 3 4 Install the seat belt. Install the roll bar.
PAGE 3
. Loosely install the left and right lower roll bar tubes using 2 bolts (1/2 x 4 inches), 2 washers, and 2 locknuts (1/2 inch) for each tube (Figure 1). 4. Loosely install the left and right support brackets using 1 bolt (1/2 x 1-1/4 inches), 1 locknut (1/2 inch), 1 bolt (1/2 x 1-3/4 inches), and 1 washer for each bracket (Figure 2). Note: Ensure that the battery cables route Note: Ensure that the battery ground cable between the right pod and the right roll bar.
PAGE 4
g239269 Figure 3 1. Right pod 3. Battery ground cable 2. Right support bracket 4. Cable g222620 Figure 4 3 1. Locknut (1/2 inch) 3. Self-tapping screw (1/4 x 5/8 inch) 2. Right seat-belt bracket 4. Bolt (1/2 x 1-1/4 inches) 2. Installing the Seat Belt Install the seat-belt assembly and buckle to the brackets using 2 bolts (1/2 x 1-1/4 inches) and 2 locknuts (1/2 inch) as shown in Figure 5. Torque the bolts to 41 N∙m (30 ft-lb).
PAGE 5
g230682 Figure 6 1. Seat-belt assembly 3. Seat-belt buckle 2. Bolt (1/2 x 1-1/4 inches) 4 Installing the Roll Bar g222814 Figure 7 Parts needed for this procedure: 1 Roll bar 4 Side plate 8 Bolt (1/2 x 3 inches) 4 Flat spacer 6 Washer 8 Locknut (1/2 inch) 3 Bumper 4 Cylindrical spacer 1 Lanyard with pivot pin, washer, and hairpin cotter 1. Bolt—1/2 x 3 inches (3) 5. Roll bar 2. Washer (3) 6. Bumper 3. Side plate (2) 7. Locknut—1/2 inch (3) 4. Flat spacer (2) 8.
PAGE 6
Operation Using the Rollover-Protection System WARNING To avoid injury or death from rollover: keep the roll bar in the fully raised, locked position and use the seat belt. g222813 Figure 9 1. Bolt (1/2 x 3 inches) Ensure that the seat is secured to the machine. 3. Locknut (1/2 inch) 2. Pivot pin 5. Raise the roll bar into the upright position and lock it into place using the pivot pin and hairpin cotter on both sides of the roll bar (Figure 10).
PAGE 7
Raising the Roll Bar g222859 Figure 11 Lowering the Roll Bar g222897 Figure 12 7
PAGE 8