Instructions / Assembly

ManualsBrandsToro ManualsOutdoor Power EquipmentTimeCutter MX5075 with MyRIDE Suspension System 50 in. Fab 24.5 HP V-Twin Gas Dual Hydrostatic Zero Turn Riding Mower

FormNo.3420-276RevA

TimeCutter

RidingMowers

ForTimeCutter

RidingMowerswithMyRide

Suspension

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Backcushion1

Flanged-hexbolt3

Installthebackcushion(machineswith

a60-inchdeckshippedinasteelcrate

only).

Pin1

Roundclip2

InstalltheMyRidesuspension.

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Installtheseat(machineswithMyRide

suspensionandshippedinawoodcrate

only).

Rearhitch1

Bolt(5/16x1inch)

Locknut(5/16inch)

Installtherearhitch.

Nopartsrequired

–

Setupthemotion-controllevers.

Nopartsrequired

–

Checkthemoweradjustment.

Ignitionkey1

Hosecoupling(notincludedwithCE

models)

Operator'sManual

Engineowner’smanual(non-Toro

engines)

Operatortrainingmaterial

Completingthesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3420-276*A

Summary of content (8 pages)

PAGE 1
Form No. 3420-276 Rev A TimeCutter® Riding Mowers For TimeCutter® Riding Mowers with MyRide® Suspension Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Qty. Use Back cushion 1 Flanged-hex bolt 3 Install the back cushion (machines with a 60-inch deck shipped in a steel crate only). 2 3 Pin Round clip 1 2 Install the MyRide suspension. No parts required – Connect the battery.
PAGE 2
1 2 Installing the Back Cushion Installing the MyRide® Suspension Machines with a 60-Inch Deck Shipped in a Steel Crate Only Machines with MyRide Suspension and Shipped in a Wood Crate Only Parts needed for this procedure: 1 Back cushion 3 Flanged-hex bolt Parts needed for this procedure: 1 Pin 2 Round clip Procedure 1. Lift up the seat onto the springs. 2. Install the back cushion using the 3 flanged-hex bolts (Figure 1). Procedure 1.
PAGE 3
. Remove the fasteners on the negative battery cable, and use them to secure the negative battery cable to the negative battery post (Figure 4). g233947 Figure 3 1. Pin 4. Round clip 2. Post 5. Shape of the key slot g018395 Figure 4 1. Negative battery cable 3.
PAGE 4
2. 4 Place the seat assembly onto the platform (Figure 6). Installing the Seat Machines with MyRide Suspension and Shipped in a Wood Crate Only No Parts Required Procedure 1. Remove the 2 hairpin cotters from the seat-pivot rod, and remove the seat-pivot rod from the platform (Figure 5). g233955 Figure 6 3. Install the seat-pivot rod by inserting the rod from the center and outward through the pivot bracket hole and seat pan hole (Figure 7).
PAGE 5
4. Install a hairpin cotter on 1 side of the seat-pivot rod, then slide the seat-pivot rod through the pivot bracket hole and seat pan hole (Figure 8). 5 Installing the Rear Hitch Parts needed for this procedure: 1 Rear hitch 2 Bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) g233953 Figure 8 5. Procedure Install the bracket to the frame as shown in Figure 11 and Figure 12. Install the other hairpin cotter on the other side of the seat-pivot rod (Figure 9). g233954 g015397 Figure 9 6.
PAGE 6
8 Setting Up the Motion-Control Levers Completing the Setup Parts needed for this procedure: No Parts Required Procedure 1. Locate the motion-control levers attached, but folded down on the machine. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3. Raise the motion control levers to the upright position. 4.
PAGE 7
Notes:
PAGE 8