FORM NQ. 3310-519 REV. C OWNER'S MANUAL MODEL NO. 58013 — THRU MODEL NO. 58114 — THRU MODEL NO. 58125 530001 THRU MODEL NO. 58220 THRU MODEL NO. 56231 — THRU AND 5 HP TILLERS SAFETY INSTRUCTIONS CAUTION: This litter is engineered and tested to offer reasonably sate and effective service, provided it is operated in strict accordance with these instructions. FAILURE TO DO S0 MAY RESULT IN PERSONAL INJURY. e " 4 TRAINING 11 Stop engine and disconnect spark plug chad wire before 1.
TABLE OF CONTENTS Page Satiety Instructions Front page Foreword .2 noose Parts Chart . General Assembly Instructions Preparation Before Starting Filing With Oif Foiling With Ga soling A Cleaner Know Your Controls Amperage Instructions Starting Stopping And Emergency Stopping Transport Passion (Depth Gauge Bar: Depth Gauge Bar Use Operating Tips Idling Pattern Siting Depth Changing Finding Witch NPT EWN . Page Adjusting Handle Height 7 Maintenance 8 Lubrication 8 Servicing Ar Cleaner .
PREPARATION BEFORE STARTING The engine has been shipped from the factory without oit and gasoline. Therefore it is essential that the Preparation Before Starting instructions on this page be strictly toweled. FILLING WITH OIL 1. Pace Pilfer on a level surface. This « very important, It the Tiller is tiled in one direction the oil level will be too low; if tilted in the other direction, the oil level will e 100 high. Marks sure the area around the filler plug is clean, and remove the plug 2.
KNOW YOUR CONTROLS To engage the clutch, push the fever forward unfit lozenges into position. To disengage, pull the lever back and xiv it to fall into the neutral position. By exerting continuous downward pressure on the fever, the unit will be i v verse. This will aid in freeing tines of tangled weds, getting rid of foreign objects that might be jammed insisting the Oilier, and for backing out of tight places. The throttle control positions are clearly marked on s cover piste.
OPERATING INSTRUCTIONS (CONTINUED) T — DEPTH GAUGE BAR USE When the depth page bar drags in the loosened soil, it holds tha tighter back, keeping the tines rigging 10 the proper depth. This saves the operator most of the fort of holding the tiler back while it is tilling soil When first breaking into untitled soil, doth tiller back manually and allow tiler to turn up hard soil. After enough sail has been loosened 1o allow depth gauge bar 10 drag in tilled soil, set bar to desired depth.
OPERATING INSTRUCTIONS (CONTINUED) The wheels may be tried 10 the front or to the rear by loosening adjustment screw positioning wheels in desuetude position and re tightening adjustment screw, CHANGING TILLING WIDTH The Rifler is shipped with all tines on the outer tine sections facing inward 1. #f you wish additional tilling width, remove the two cuter blades from each outer tine section IMPORTANT. The tines ars right and left hand, and must be switched from one and to the other.
MAINTENANCE A CAUTION: When nonperforming any maintenance on your Filter, disconnect the spark plug wire and secure it in'the V-shaped notch in the engine shroud to prevent accidental contact with the spark plug. T 9 PP PRI PP SITES DEN PP DOSS LUBRICATION Keep Tiller properly lubricated 1.
MAINTENANCE (CONTINUED) CHANGING TRANSMISSION OIL Change transmission ol once each year. Drain after Tiller has been in aeration; oil will be warm and will drain easily 1. Remove gasoline from tank Lo prevent spiting when unit it tipped 16 drain oil 2. Position Oilier on 3 flat level surface 3. Removal filler plug 4. Tip Tiller forward and slow oil 1o drain anti a container Be sure oil drains completely . B. Refit with 8 good grade of SAE 90 gear oil.
MAINTENANCE (CONTINUED) SPARK PLUG Use spark plug of the type specified below for replacement. Clean and reset the gap a1 030 inch every 25 hours of operation. Apply Hg ht coating of graphite grease on threads before replacing plug. H plug is pitted or Fig. 28 CARBURETOR ADJUSTMENT Minor carburetor adjustment may be required 10 compel sate for differences in fuel. temperature, altitude and load Adjust carburetor with tank half {ubl of regular grade gassing initial Adjustment.
IMPORTANT ORDERING INSTRUCTIONS Repair parts are available from your TROD dealer. To insure getting correct parts without delay, please furnish the fallowing information 1. Model and serial number of your tiller as shown on the name plate. . Part pubes, description snd quantity of each pert required. w . Do not order by reference number. use part number only. For your own convenience, we suggest you write in the numbers of your machine in the space provided below.