Form No. 3441-962 Rev C Flex-Force Power System™ 60V Stick Edger Model No. 51833—Serial No. 321000001 and Up Register at www.Toro.com.
Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
Safety 7. Charge the battery pack with only the battery charger specified by Toro. A charger suitable for 1 type of battery pack may create a risk of fire when used with another battery pack. 8. Charge the battery pack in a well-ventilated area only. 9. Do not expose a battery pack or battery charger to fire or to temperatures higher than 68°C (154°F). 10. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions.
10. Do not overreach—Keep proper footing and balance at all times, especially on slopes. Walk, never run with the appliance. 7. Do not replace the existing non-metallic cutting means on the appliance with a metallic cutting means. 11. Stay alert—Watch what you are doing and use common sense when operating the appliance. Do not use the appliance while ill, tired, or under the influence of alcohol or drugs. 8. 12. Ensure that the ventilation openings are kept clear of debris.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
decal144-3094 144-3094 1. The battery pack is charging. 3. The battery pack is over or under the appropriate temperature range. 2. The battery pack is fully charged. decal139-5210 139-5210 4. Battery pack charging fault 1. Warning—read the Operator’s Manual; stay away from moving parts; keep all guards in place; wear eye protection; do not operate in wet conditions. decal140-8475 140-8475 1. Read the Operator’s Manual. 2. Call2Recycle® battery recycling program 3.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Qty. Use Allen wrench 1 Unfold the handle. Auxiliary handle assembly 1 Install the auxiliary handle. Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, refer to Charging the Battery Pack (page 13). 1 Unfolding the Handle Parts needed for this procedure: 1 Allen wrench Procedure 1. Unfold the handle (A of Figure 3). 2.
g333338 Figure 3 8
2 Installing the Auxiliary Handle Parts needed for this procedure: 1 Auxiliary handle assembly Procedure 1. Separate the auxiliary handle from the handle plate by removing the 4 screws (A of Figure 4). 2. Line up the auxiliary handle with auxiliary handle plate on the edger handle (B of Figure 4). 3. Secure the auxiliary handle to the handle plate with the 4 screws previously removed (C of Figure 4).
Specifications Product Overview Model 51833 Blade Length 203 mm (8 inches) Rated Voltage 60V DC maximum, 54 VDC nominal usage No-load Speed 7000 rpm Weight (without battery pack) 4.7 kg (10.
Shutting Off the Edger Operation To shut off the trimmer, release the trigger. Starting the Edger Whenever you are not using the edger or are transporting the edger to or from the work area, remove the battery pack. 1. Align the cavity in the battery pack with the tongue on the handle housing (Figure 7). 2. Push the battery pack into the handle until the battery locks into the latch (Figure 7).
Adjusting the Depth of Cut 1. Remove the battery from the edger. 2. Loosen the wing nut on the wheel and move it up or down in the track to increase or decrease the depth (Figure 10). g333293 Figure 10 3. Adjust the depth so that the blade barely touches the ground when the machine is held in a normal working position. 4. Tighten the wing nut. 5. Standing in a normal working position, check the depth of cut again and correct if necessary.
Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions. Battery pack and/or battery charger is over or under the appropriate temperature range Red blinking Battery pack charging fault* *Refer to Troubleshooting (page 16) for more information.
Maintenance After each use of the edger, complete the following: 1. Remove the battery from the edger. 2. Wipe the edger clean with a damp cloth. Do not hose the edger down or submerge it in water. 3. Wipe or scrape clean the cutting head area any time there is an accumulation of debris. 4. Check and tighten all fasteners. If any part is damaged or lost, repair or replace it. 5.
6. Storage Tighten the wing nut to secure the wheel. Important: Store the tool, battery pack, and Replacing the Skid Plate charger only in temperatures that are within the appropriate range; refer to Specifications (page 10). If the skid plate becomes worn or damaged, replace it; contact your authorized Toro distributor. Important: If you are storing the battery pack for 1. Ensure that the battery is removed from the machine. 2.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Problem The tool does not run or run continuously. Possible Cause Corrective Action 1. There is moisture on the leads of the battery pack. 1. Allow the battery pack to dry or wipe it dry. 2. The battery is not fully installed into the tool. 2. Remove and then replace the battery into the tool making sure that it is fully installed and latched.
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
