FORM NO. 3321–578GB Rev A Air Raket Blower Model No.
Safety IMPORTANT SAFETY INSTRUCTIONS • Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow. • DRESS PROPERLY. Do not wear loose clothing or jewelry. Pin up long hair. Be aware of the position of the blower and the air inlets during operation. Loose clothing, jewelry and hair can be drawn into the inlets (Fig. 1) and may result in personal injury. Always wear substantial footwear and long pants.
Read operator’s manual Electrical shock/electrocution Consult technical manual for proper service procedures Disconnect power Do not open or remove safety shields while engine is running Severing of fingers or hand—impeller blade Wear eye protection Assembly Note: Refer to Figures section at the back of the manual. POTENTIAL HAZARD • Motor impeller rotates for a few seconds after blower is turned off. WHAT CAN HAPPEN • Rotating impeller can cut or injure fingers.
Before Starting Operation This appliance is intended for residential use only. Securing Extension Cord Use only an extension cord recommended for outdoor use. POTENTIAL HAZARD • Debris can be thrown by unit in operator’s or bystander’s direction. WHAT CAN HAPPEN • Flying debris can cause serious personal injury to operator or bystanders. HOW TO AVOID THE HAZARD • Always wear safety goggles or other suitable eye protection, long pants and shoes while operating unit.
Bag Cleaning 1. With vac tube and bag attached, pick up unit by vac tube handle and housing handle. Bag should be positioned fairly low at your side. Place bag strap over shoulder and adjust length to fit. Do not store debris in vacuum bag. Empty bag after each use. After three uses, clean bag thoroughly. Turn bag inside out and shake out dust and excess debris vigorously. Once a year, if necessary, wash the bag by hand in soapy water. 2. Turn unit on. 3.
Troubleshooting PROBLEM Unit won’t run or stops running POSSIBLE CAUSE CORRECTIVE ACTION 1. Unit not plugged in 1. Plug in unit 2. On/off switch in “off” position 2. Turn to “on” 3. Inlet cover or vacuum tube incorrectly installed or removed 3. Secure cover or vacuum tube 4. Blown fuse or tripped circuit breaker 4. Replace fuse or reset breaker 5. Faulty extension cord 5. Replace cord Unit seems to be low on power 1. Impeller is worn 1.
TORO AUSTRALIA POWER EQUIPMENT WARRANTY Subject to the warranty condition below, this tool (hereinafter called “the product”) is warranted by Toro Australia (hereinafter called “the Company”) to be free from defects in material or workmanship for a period of 24 months from the date of original purchase covering both parts and labour. Under the terms of this warranty, the repair or replacement of any part shall be the opinion of the Company or its authorised agent.
Figures 1 1 4 7 1 2 2 1 2 1. Model and serial number decal 2 m-4027 2. Air inlet 3 2 1 5 4 3 1604 3. Tab 1 1596 1571 1. Inlet cover 3. Tab 4. Latch 2 1. Housing pointer 2. Vacuum tube pointer 8 1 1. Blower tube 2. Blower housing outlet 3 1601 1. Pointers aligned in lock postion 6 1605 1 1. Pointers aligned in lock position 3 9 4 1. Inlet cover 2. Housing pointer 1596 3. Cover pointer 4.
Figures 10 13 1 16 1 2 1 3 1. Bag collar 2. Bag collar flange 1822 1597 3. Velcrot strap 1. Air flow adjuster m-4003 1. Cord lock 11 17 14 2063 1 1989 1. Cord lock 12 1 4 2 3 15 m-3990 1. Bag collar 2. Tab 3. Blower housing outlet 4. Latch 1576 1 1990 1.
