Form No. 3424-868 Rev A PowerPlex 14in 40V MAX String Trimmer 51482, 51482T Desbrozadora PowerPlex 40 V MAX de 36 cm (14") 51482, 51482T Débroussailleuse à fil PowerPlex 36 cm (14 po) 40 V MAX 51482, 51482T www.Toro.com.
Form No. 3424-865 Rev A PowerPlex 14in 40V MAX String Trimmer Model No. 51482—Serial No. 319000001 and Up Model No. 51482T—Serial No. 319000001 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code (if equipped) on the serial number plate to access warranty, parts, and other product information. If you have questions or problems, call toll free 1-800-237-2654 (US) or 1-800-248-3258 (Canada) before returning this product. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Safety E. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. F. Keep your hands and feet away from the cutting area. 3. Power tool use and care A. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. B.
conditions and the work to be performed. Using the power tool for operations different from those intended could result in a hazardous situation. 4. J. Keep guards in place and in working order. K. Check for damaged parts. Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-2465 136-2465 Model 51482 decal136-2466 136-2466 Model 51482T decal136-2473 136-2473 decal136-2471 136-2471 decal138-6694 138-6694 decal136-2476 136-2476 5 1. The battery pack is charging. 3. The battery pack is too warm. 2. The battery pack is fully charged. 4. Replace the battery pack.
decal136-2539 136–2539 1. Charge the battery where the temperature is between 0°C and 40°C (32°F and 104°F). decal136-2533 136-2533 1. Warning—read the Operator’s Manual; keep away from moving parts; keep all guards and covers in place; wear eye protection; do not operate in wet conditions. decal136-2534 136-2534 1. The battery does not come out of the box fully charged. 4. Stop—follow these instructions before first use. 2. Place the battery in the battery charger. 5. Read the Operator’s Manual.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty. No parts required – Mount the battery charger (optional). Connector knob 1 Unfold the handle. Auxiliary handle 1 Install the auxiliary handle. Guard Phillips head screw 1 4 Install the guard. Note: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, refer to Charging the Battery Pack (page 11).
2 Unfolding the Handle Parts needed for this procedure: 1 Connector knob Procedure 1. Unfold the handle (A of Figure 3). 2. Install the connector knob to secure the handle (B of Figure 3). Note: The nut that holds the handle connector knob in place is lightly secured in the connector housing with a piece of tape. Remove the tape after you install the connector knob.
3 4 Installing the Auxiliary Handle Installing the Guard Parts needed for this procedure: Parts needed for this procedure: 1 Auxiliary handle 1 Guard 4 Phillips head screw Procedure Procedure 1. Line up the groove along the handle with the groove on the auxiliary handle and slide the auxiliary handle toward the trimmer handle (A of Figure 4). 2. Snap the handle securely into place (B of Figure 4).
Product Overview Operation Specifications Starting the Trimmer 1. Appropriate Temperature Ranges Charge the battery at 0°C (32°F) to 40°C (104°F)* Use products at -15°C (5°F) to 60°C (140°F) Store products at -15°C (5°F) to 60°C (140°F) Unplug the charger if Below 0°C (32°F) or above 40°C (104°F) Make sure that the vents on the trimmer are clear of any dust and debris. *Charging time will increase if you do not charge the battery within this range.
Shutting Off the Trimmer To shut off the trimmer, release the trigger. Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, remove the battery pack. Removing the Battery Pack from the Trimmer Press the battery latch on the machine to release the battery pack and slide the battery pack out of the machine (Figure 9). g228487 Figure 10 1. Battery pack cavity 2. Battery pack terminals 4. Battery-charge-indicator button 5. LED indicators (current charge) 3.
Left Light Right Light Adjusting the Auxiliary Handle Indicates: Off Red Charger is on; no battery pack inserted Red Red Battery pack is charging Green Red Battery pack is charged Orange Red Battery pack is too warm Red Blinking Red Replace the battery pack 1. Release the auxiliary-handle latch (A of Figure 13). 2. Slide the auxiliary handle up or down to your desired height (B of Figure 13). Important: Do not remove the rubber bumper. Advancing the Line Using the Bump Feed 1.
Operating Tips • Keep the trimmer tilted toward the area being cut; this is the best cutting area. • The string trimmer cuts when you move it from left to right. This prevents the trimmer from throwing debris at you. • Use the tip of the string to do the cutting; do not force the string head into uncut grass. • Wire and picket fences can cause the string to wear rapidly and even break. Stone and brick walls, curbs, and wood can also cause the string to wear rapidly. • Avoid trees and shrubs.
Maintenance Replacing the Spool After each use of the trimmer, complete the following: Use only 2 mm (0.08 inch) diameter monofilament string. Use the original manufacturer’s replacement string for best performance (Toro Part No. 88546). 1. Remove the battery from the trimmer. 2. Wipe the trimmer clean with a damp cloth. Do not hose the trimmer down or submerge it in water. Important: Using a larger diameter string causes the motor to overheat and fail. CAUTION 1. Remove the battery. 2.
Storage Replacing the String 1. Remove the battery. Important: Store the tool, battery pack, and 2. Remove the spool; refer to Replacing the Spool (page 14). charger only in temperatures that are within the appropriate range; refer to Specifications (page 10). Important: If you are storing the tool for a year or longer, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn blue on the battery. Do not store a fully charged or fully depleted battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Problem Possible Cause Corrective Action An audible tone sounds when advancing the line using the bump feed. 1. This is a normal occurrence. 1. Stop the tool by releasing the trigger and then start the tool. It is difficult to remove the battery pack from the tool. 1. The battery pack/tool is new or there is corrosion in the battery terminals and/or the terminals on the tool. 1. Clean the terminals on the battery pack and the tool.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
Form No. 3424-866 Rev A Desbrozadora PowerPlex 40 V MAX de 36 cm (14") Nº de modelo 51482—Nº de serie 319000001 y superiores Nº de modelo 51482T—Nº de serie 319000001 y superiores Registre su producto en www.Toro.com.
Importante: Con su dispositivo móvil, puede Si usted tiene alguna pregunta o algún problema, llame al teléfono gratuito 1-800-237-2654 (EE.UU.) o 1-800-248-3258 (Canadá) antes de devolver este producto. escanear el código QR (en su caso) de la place del número de serie para acceder a información sobre la garantía, las piezas, y otra información sobre el producto.
Seguridad conectar la herramienta a la toma de corriente y/o a la batería, y antes de levantar o transportar la herramienta. Transportar las herramientas eléctricas con el dedo sobre el interruptor o enchufar herramientas eléctricas con el interruptor en la posición de encendido es una invitación al accidente. ADVERTENCIA Si no se observan todas las advertencias e instrucciones, pueden producirse descargas eléctricas, incendios y/o lesiones graves. Lea todas las advertencias e instrucciones de seguridad.
el mantenimiento de la seguridad de la herramienta eléctrica. móviles están correctamente alineadas y que se mueven libremente sin agarrotarse, que no hay piezas rotas, y que no hay otras circunstancias que podrían afectar al uso de la herramienta eléctrica. Si existen daños, haga reparar la herramienta eléctrica antes de usarla. Muchos accidentes se deben a un mantenimiento deficiente de las herramientas eléctricas. G. 4. 5. Mantenga debidamente el aparato.
Pegatinas de seguridad e instrucciones Las pegatinas de seguridad e instrucciones están a la vista del operador y están ubicadas cerca de cualquier zona de peligro potencial. Sustituya cualquier pegatina que esté dañada o que falte. decal136-2465 136-2465 Modelo 51482 decal136-2466 136-2466 Modelo 51482T decal136-2473 136-2473 decal136-2471 136-2471 decal138-6694 138-6694 decal136-2476 136-2476 5 1. La batería se está cargando. 3. La batería está demasiado caliente. 2.
decal136-2539 136-2539 1. Cargue la batería a una temperatura de entre 0 °C y 40 °C (32 °F y 104 °F). decal136-2533 136-2533 1. Advertencia: lea el Manual del operador; manténgase alejado de las piezas móviles; mantenga colocados todos los protectores y cubiertas; utilice protección ocular; no utilice en condiciones húmedas. decal136-2534 136-2534 1. La batería no se suministra 4. Pare: siga estas totalmente cargada. instrucciones antes del primer uso. 2. Coloque la batería en el cargador. 5.
Montaje Piezas sueltas Utilice la tabla siguiente para verificar que no falta ninguna pieza. Procedimiento 1 2 3 4 Descripción Uso Cant. No se necesitan piezas – Monte el cargador de la batería (opcional) Pomo del conector 1 Despliegue el mango. Empuñadura auxiliar 1 Instale la empuñadura auxiliar. Protector Tornillo Phillips 1 4 Instale el protector. Nota: En el momento de la compra la batería no está totalmente cargada.
2 Cómo desplegar el mango Piezas necesarias en este paso: 1 Pomo del conector Procedimiento 1. Despliegue el mango (Figura 3, A). 2. Instale el pomo del conector para fijar el mango (Figura 3, B). Nota: La tuerca que sujeta el pomo del conector del mango está sujeta a la carcasa del conector con un trozo de cinta adhesiva. Retire la cinta después de instalar el pomo del conector.
3 4 Instalación de la empuñadura auxiliar Instalación del protector Piezas necesarias en este paso: Piezas necesarias en este paso: 1 Empuñadura auxiliar 1 Protector 4 Tornillo Phillips Procedimiento Procedimiento 1. Alinee la ranura del mango con la ranura de la empuñadura auxiliar y deslice la empuñadura auxiliar hacia el mango de la desbrozadora (Figura 4, A). 2. Encaje firmemente la empuñadura en su sitio (Figura 4, B).
El producto Operación Especificaciones Cómo arrancar la desbrozadora Intervalos de temperatura adecuados Cargue la batería a Entre 0 °C y 40 °C (32 °F y 104 °F)* Utilice el producto a Entre -15 °C y 60 °C (5 °F y 140 °F) Almacene el producto a Entre -15 °C y 60 °C (5 °F y 140 °F) Desenchufe el cargador a Menos de 0 °C (32 °F) o más de 40 °C (104 °F) 1. Compruebe que los orificios de ventilación de la desbrozadora están libres de polvo y residuos.
Cómo apagar la desbrozadora Para apagar la desbrozadora, suelte el gatillo. Cuando no esté utilizando la desbrozadora o la esté transportando hacia o desde el área de trabajo, retire la batería. Cómo retirar la batería de la desbrozadora g228487 Presione el cierre de la batería en la máquina para liberar la batería, y retire la batería de la máquina (Figura 9). Figura 10 1. Hueco de la batería 4. Botón del indicador de carga de la batería 2. Terminales de la batería 5.
Indicador izquierdo Indicador derecho Cómo ajustar la empuñadura auxiliar Indica: Apagado Rojo Cargador encendido, sin batería Rojo Rojo La batería se está cargando Verde Rojo La batería está cargada Naranja Rojo La batería está demasiado caliente Rojo intermitente Rojo Sustituya la batería 1. Abra el pestillo de la empuñadura auxiliar (Figura 13, A). 2. Deslice la empuñadura auxiliar hacia arriba o abajo hasta la posición deseada (Figura 13, B).
Consejos de operación • Mantenga la desbrozadora inclinada hacia la zona que está cortando; ésta es la mejor zona de corte. • La desbrozadora de hilo corta al moverla de izquierda a derecha. Esto evita que la desbrozadora arroje residuos hacia usted. • Utilice el extremo del hilo para cortar; no introduzca la base entera a la fuerza en la hierba sin cortar. • Las vallas de alambre o madera pueden provocar que el hilo se desgaste rápidamente, e incluso pueden romperlo.
Mantenimiento Cambio del carrete Después de cada uso de la desbrozadora, complete los procedimientos siguientes: Utilice solamente hilo monofilamento de 2 mm (0.08") de diámetro. Use el hilo de repuesto del fabricante original para obtener el mejor rendimiento (Pieza Toro N° 88546). 1. Retire la batería de la desbrozadora. 2. Limpie la desbrozadora pasando un paño húmedo. No lave la desbrozadora con una manguera ni la sumerja en agua.
Almacenamiento Cambio del hilo 1. Retire la batería. Importante: Almacene la herramienta, la 2. Retire el carrete; consulte Cambio del carrete (página 14). batería y el cargador solo a temperaturas que estén dentro del intervalo apropiado; consulte Especificaciones (página 10). Importante: Si va a almacenar la herramienta durante un año o más, retire la batería de la herramienta y cargue la batería hasta que 2 o 3 de los indicadores LED de la batería cambien a azul.
Solución de problemas Realice solo los pasos descritos en estas instrucciones. Cualquier otro trabajo de inspección, mantenimiento o reparación debe ser realizado por un Servicio Técnico Autorizado o por un especialista autorizado si no puede solucionar el problema usted mismo. Problema La herramienta no arranca. Posible causa 1. La batería no está correctamente instalada en la herramienta. 1.
Problema Posible causa Acción correctora 1 indicador LED de la batería parpadea. 1. El voltaje de la batería es bajo. 1. Coloque la batería en el cargador. Se produce un tono audible al avanzar el hilo usando la alimentación por golpe. 1. Esto es normal. 1. Suelte el gatillo para parar la herramienta, luego arranque la herramienta. Es difícil retirar la batería de la herramienta. 1. La batería/herramienta es nueva o hay corrosión en los terminales de la batería o los terminales de la herramienta.
Información sobre las Advertencias de la Proposición 65 de California ¿Qué significa esta advertencia? Puede ver un producto a la venta que lleva una etiqueta de advertencia como la siguiente: ADVERTENCIA: Cáncer y daños reproductivos—www.p65Warnings.ca.gov. ¿Qué es la Proposición 65? La Proposición 65 afecta a cualquier empresa que tenga presencia en California, que venda productos en California, o que fabrique productos que podrían ser introducidos o vendidos en California.
Form No. 3424-867 Rev A Débroussailleuse à fil PowerPlex 36 cm (14 po) 40 V MAX N° de modèle 51482—N° de série 319000001 et suivants N° de modèle 51482T—N° de série 319000001 et suivants Enregistrez votre produit à www.Toro.com.
Important: Avec votre appareil mobile, vous Pour tout conseil ou renseignement, appelez notre numéro vert 1-800-237-2654 (États-Unis) ou 1-800-248-3258 (Canada) avant de renvoyer ce produit. pouvez scanner le code QR (le cas échéant) sur la plaque du numéro de série pour accéder à l'information sur la garantie, les pièces détachées et autres renseignements concernant le produit.
Sécurité C. Évitez tout démarrage accidentel. Assurez-vous que l'interrupteur marche/arrêt est en position ARRÊT avant de connecter l'outil à une source d'alimentation et/ou à la batterie, de le prendre en main ou de le transporter. Des accidents peuvent se produire si vous transportez un outil électrique en gardant le doigt sur l'interrupteur d'alimentation ou si vous le mettez sous tension sans avoir placé l'interrupteur en position arrêt. D. Ne travaillez pas trop loin devant vous.
E. Rangez les outils électriques à l'intérieur lorsqu'ils ne servent pas. Lorsque les outils ne sont pas utilisés, rangez-les dans un local sec en hauteur ou sous clé, hors de la portée des enfants. F. Maintenez les outils électriques en état de marche. Vérifiez si des pièces sont mal alignées, grippées, cassées ou présentent tout autre défaut susceptible d'affecter le bon fonctionnement de l'outil électrique. S'il est endommagé, faites réparer l'outil électrique avant de l'utiliser.
Autocollants de sécurité et d'instruction Des autocollants de sécurité et des instructions bien visibles par l'opérateur sont placés près de tous les endroits potentiellement dangereux. Remplacez tout autocollant endommagé ou manquant. decal136-2465 136-2465 Modèle 51482 decal136-2466 136-2466 Modèle 51482T decal136-2473 136-2473 decal136-2471 136-2471 decal138-6694 138-6694 decal136-2476 136-2476 1. La batterie est en charge. 2. La batterie est complètement chargée. 5 3.
decal136-2539 136-2539 1. Chargez la batterie à une température ambiante comprise entre 0 °C et 40 °C (32 °F et 104 °F). decal136-2533 136-2533 1. Attention – lisez le manuel de l'utilisateur; n'approchez pas des pièces en mouvement; laissez toutes les protections et capots en place; protégez-vous les yeux; n'utilisez pas l'appareil par temps humide. decal136-2534 136-2534 1. La batterie n'est pas chargée au départ. 4. Stop – suivez ces instructions avant la première utilisation. 2.
Mise en service Pièces détachées Reportez-vous au tableau ci-dessous pour vérifier si toutes les pièces ont été expédiées. Description Procédure 1 2 3 4 Qté Utilisation Aucune pièce requise – Montage du chargeur de batterie (option). Bouton de fixation 1 Dépliage du manche. Poignée auxiliaire 1 Montage de la poignée auxiliaire. Déflecteur Vis cruciforme 1 4 Montage du déflecteur. Remarque: Quand vous l'achetez, la batterie n'est pas complètement chargée.
2 Dépliage du manche Pièces nécessaires pour cette opération: 1 Bouton de fixation Procédure 1. Dépliez le manche (encadré A de la Figure 3). 2. Montez le bouton de l'accouplement pour fixer le manche (encadré B de la Figure 3). Remarque: L'écrou qui maintient le bouton de l'accouplement en place est légèrement maintenu dans le logement de l'accouplement par le morceau de ruban adhésif. Après avoir installé le bouton de l'accouplement, retirez le ruban adhésif.
3 4 Montage de la poignée auxiliaire Montage du déflecteur Pièces nécessaires pour cette opération: Pièces nécessaires pour cette opération: 1 Poignée auxiliaire 1 Déflecteur 4 Vis cruciforme Procédure Procédure 1. Alignez le creux le long du manche sur le creux de la poignée auxiliaire et faites glisser la poignée auxiliaire vers le manche de la débroussailleuse (encadré A de la Figure 4). 2. Enclenchez la poignée fermement en place (encadré B de la Figure 4).
Vue d'ensemble du produit Utilisation Démarrage de la débroussailleuse Caractéristiques techniques 1. Plages de température adéquates Charger la batterie entre 0 °C (32 °F) et 40 °C (104 °F)* Utiliser les produits entre -15 °C (5 °F) et 60 °C (140 °F) Remiser les produits entre -15 °C (5 °F) et 60 °C (140 °F) Débrancher le chargeur au-dessous de 0 ºC (-32 ºF) ou au-dessus de 40 ºC (104 ºF) Assurez-vous que les prises d'air de la débroussailleuse sont exemptes de toute poussière et tout débris.
Arrêt de la débroussailleuse Pour arrêter la débroussailleuse, relâchez la gâchette. Chaque fois que vous cessez d'utiliser la débroussailleuse ou que vous la transportez vers ou de la zone de travail, enlevez la batterie. Retrait de la batterie de la débroussailleuse Appuyez sur le verrou de batterie sur la machine afin de débloquer la batterie, et faites glisser cette dernière hors de la machine (Figure 9). g228487 Figure 10 1. Creux de la batterie 4. Bouton indicateur de charge 2.
Voyant gauche Voyant droit Réglage de la poignée auxiliaire Indique : Éteint Rouge Le chargeur est en marche; aucune batterie n'est insérée Rouge Rouge La batterie est en charge Vert Rouge La batterie est chargée Orange Rouge La batterie est trop chaude Rouge clignotant Rouge Remplacez la batterie 1. Déverrouillez le verrou de la poignée auxiliaire (encadré A de la Figure 13). 2. Élevez ou abaissez la poignée auxiliaire à la hauteur voulue (encadré B de la Figure 13).
Conseils d'utilisation • Gardez la débroussailleuse inclinée vers la zone à couper, la meilleure zone de coupe. • Pour couper, déplacez la débroussailleuse à fil de gauche à droite. Cela évite la projection de débris dans votre direction. • Utilisez l'extrémité du fil pour couper; ne forcez pas la tête de coupe dans l'herbe non coupée. • Les câbles et clôtures peuvent accélérer l'usure du fil, voire même le casser.
Entretien Remplacement de la bobine Après chaque utilisation de la débroussailleuse, suivez les procédures ci-après : Utilisez uniquement du fil monofilament de 2 mm (0,08 po) de diamètre. Pour garantir des performances optimales, utilisez le fil de rechange du fabricant d'origine (réf. Toro 88546). 1. Enlevez la batterie de la débroussailleuse. 2. Essuyez la débroussailleuse avec un chiffon humide. Ne lavez pas la débroussailleuse au jet d'eau et ne la trempez pas dans l'eau.
Remisage Remplacement du fil 1. Retirez la batterie. Important: Remisez l'outil, la batterie et le 2. Déposez la bobine; voir Remplacement de la bobine (page 14). chargeur uniquement à des températures comprises dans la plage adéquate; voir Caractéristiques techniques (page 10). Important: Si vous remisez l'outil pendant un an ou plus, retirez la batterie et chargez-la jusqu'à ce que 2 ou 3 de ses diodes deviennent bleues. Ne remisez pas une batterie à pleine charge ou complètement déchargée.
Dépistage des défauts Effectuez uniquement les opérations décrites dans cette notice. Tout autre travail d'inspection, d'entretien ou de réparation doit être réalisé par un centre d'entretien agréé ou autre spécialiste qualifié si vous n'arrivez pas à résoudre le problème vous-même. Problème L'outil ne démarre pas. Cause possible Mesure corrective 1. La batterie n'est pas complètement installée dans l'outil. 1.
Problème Cause possible Mesure corrective L'avance du fil par frappe sur le sol produit un son. 1. Cela est parfaitement normal. 1. Arrêtez l'outil en relâchant la gâchette, puis remettez-le en marche. Il est difficile de retirer la batterie de l'outil. 1. La batterie/l'outil sont neufs, ou les bornes de la batterie et/ou les bornes de l'outil sont corrodées. 1. Nettoyez les bornes de la batterie et de l'outil.
Proposition 65 de Californie – Informations concernant cet avertissement En quoi consiste cet avertissement? Certains produits commercialisés présentent une étiquette d'avertissement semblable à ce qui suit : AVERTISSEMENT :Cancer et troubles de la reproduction – www.p65Warnings.ca.gov. Qu’est-ce que la Prop 65? La Prop 65 s'applique à toute société exerçant son activité en Californie, qui vend des produits en Californie ou qui fabrique des produits susceptibles d'être vendus ou importés en Californie.