Setup Instructions

ManualsBrandsToro ManualsGreens RollerGreensPro 1200 Greens Roller

FormNo.3376-153RevB

GreensPro™1200GreensRoller

ModelNo.44907—SerialNo.313000001andUp

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Liftarmcatchassembly

Installtheliftarmcatchassembly

Liftarmassembly

Installtheliftarmassembly

Transportwheels2Installthetransportwheels

Reartowbarassembly1Installthereartowbarassembly

Liftbar

Installtheliftbar

Steeringwheel

Steeringshaftcover

Steeringwheelcap

Installthesteeringwheel

Seat

1Installtheseat

Nopartsrequired

–

Removethemachinefromthepallet

Keepthemachineonthepalletwhileinstallingthe

components.

InstallingtheLiftArmCatch

Assembly

Partsneededforthisprocedure:

Liftarmcatchassembly

Procedure

1.Hookthespringontothecatch(

Figure1).

G018762

Figure1

1.Bolts

2.Spring

2.Placethecatchontothebolts.

3.Tightenthenutssothatthecatchmechanismdoesnot

move,thenbackthenutoffoneachcatchtoallowthe

catchmechanismtomovefreely.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK.

AllRightsReserved

*3376-153*B

Summary of content (4 pages)

PAGE 1
Form No. 3376-153 Rev B GreensPro™ 1200 Greens Roller Model No. 44907—Serial No. 313000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 Description Use Qty.
PAGE 2
1 2 Installing the Lift Arm Assembly 54 Parts needed for this procedure: 1 3 G018764 Figure 3 Lift arm assembly Procedure 1. Shoulder end of gas ram 4. Washer 2. Gas ram 3. Lift arm 5. Nut 1. Remove the seat pan bolt and flip the seat pan up. 6. Install the washers and nut on the other side of the gas ram. 2. Remove the top half of the clamps on the base then feed the lift arm assembly under the seat support. 7. Tighten the nut.
PAGE 3
4 Installing the Rear Tow Bar Assembly Parts needed for this procedure: 1 Rear tow bar assembly Procedure 1. Remove the transmission cover to allow access to the nuts for the tow bar. Figure 4 2. Remove the outer half of the clamps on the back of the machine. 3. Place the tow bar in position and install the clamps. Tighten the nuts to 47.5 N-m (35 ft-lb). Note: Do not overtighten. This assembly needs to pivot easily. 6. Washer 7. Nut 3. Nut 4. Washers 5. Lift arm assembly 8. Washer 9. Bolt 3.
PAGE 4
1 234 5 1 2 3 4 5 6 7 6 7 G018767 Figure 6 G018766 Figure 5 1. Steering wheel cap 5. Steering wheel 2. Bolt 6. Steering shaft cover 3. Lock washer 7. Steering shaft 1. 2. 3. 4. Bolt Lock washer Washer Nut 5. Bolt 6. Washer 7. Nut 4. Large washer 8 2. Slide the steering wheel down onto the shaft and install the large washer, lock washer, and tighten with the bolt. Torque the steering wheel bolt to 25.4 N-m (225 in-lb). Removing the Machine from the Pallet 3.