Form No. 3376-137 Rev B GreensPro™ 1200 Greens Roller Model No. 44907—Serial No. 313000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Important: This engine is not equipped with a spark arrester muffler.
Contents Introduction .................................................................. 2 Safety ........................................................................... 4 Safe Operating Practices........................................... 4 Toro Safety............................................................. 5 Sound Power Level .................................................. 6 Sound Pressure Level............................................... 6 Vibration Level ..................................
Preparation Safety • While operating the machine, always wear substantial This machine meets or exceeds CEN standard EN ISO 12100: 2010 specification in effect at the time of production. Improperly using or maintaining the machine can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means Caution, Warning, or Danger—personal safety instruction.
Maintenance and Storage • Before dismounting the machine, ensure that it is parked • • • • • • • • • • • • • • • • • • on a level surface so that it does not roll away. Chock the wheels or rollers as required. Slow down and use extra care on hillsides. Be sure to travel in the recommended direction on hillsides. Turf conditions can affect the stability of the machine. Use caution while operating near drop-offs. Slow down and use caution when making turns and when changing directions on slopes.
Vibration Level • The direction on the machine (right or left) is determined from the seated operator’s position. Hand-Arm • Know how to stop the engine quickly. • Do not operate the machine while wearing tennis shoes Measured vibration level for right hand = 3 m/s2 or sneakers. Measured vibration level for left hand = 3 m/s2 • Wearing safety shoes and long pants is advisable and Uncertainty Value (K) = 1.5 m/s2 required by some local ordinances and insurance regulations.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-6686 111–5646 1. Hydraulic oil 1. Cutting/dismemberment hazard, fan; entanglement hazard, belt—keep away from moving parts; keep all guards in place. 2. Read the Operator's Manual. 111–5649 1. Traction pedal, push to move left. 111–5650 1. Traction pedal, push to move right. 111–5648 1.
111–5647 1. 1) Release the latch 3. 1) Release the latch securing the transport securing the transport wheels in the lowered wheels in the raised position; 2) Rotate the lift position; 2) Rotate the lift bar to raise the transport bar to lower the transport wheels into the up position. wheels into the down position. 2. Striking hazard—read the Operator’s Manual. 85 lbs 380 N 111-5652 111–5652 1. Read the Operator’s Manual; Caution—tongue weight 380 N (85 lb).
Controls Product Overview Note: Refer to your engine operator's manual for complete control information. Steering Wheel The steering wheel (Figure 3) controls the angle of the smoothing rollers, which in turn steer the unit. The amount the wheel can be turned is limited, so the turning circle of the greens roller is relatively large. To move forward or back simply turn the steering wheel to suit the direction you are aiming for.
Engine Controls Throttle Lever The throttle lever (Figure 6) controls the speed (rpm) of the engine. It is located next to the choke control. It sets the engine rpm and therefore can increase and decrease the speed of the machine. For best performance, set this control to the fast position. On/Off Switch The On/Off switch (Figure 5) allows the operator of the machine to start and stop the engine. This switch is located on the front of the engine.
Filling the Fuel Tank Operation • For best results, use only clean, fresh (less than 30 days Note: Determine the left and right sides of the machine from the normal operating position. old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). • Ethanol: Gasoline with up to 10% ethanol (gasohol) Think Safety First or 15% MTBE (methyl tertiary butyl ether) by volume is acceptable. Ethanol and MTBE are not the same.
1 DANGER In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any gasoline that spills. • Do not fill the fuel tank completely full. Add gasoline to the fuel tank until the level is 25 mm (1 inch) below the top of the tank. This empty space in the tank allows the gasoline to expand.
out, because the rope may break or the recoil assembly may be damaged. B. Slide the bar onto the tab on the left hand side of the lifting arm assembly and secure it with a lynch pin (Figure 9). 6. When the engine has started, push the choke lever to the off position. 1 2 7. Move the throttle lever to the desired setting (usually Fast). Stopping the Engine 1. Turn the engine speed to idle, and allow it to run for 10 to 20 seconds. 2. Turn the On/Off switch to the off position. 3.
3. Hold onto the steering wheel, and slowly press either the left or right motion pedal with your corresponding foot, in whichever direction you wish to move. Note: The further you press the pedal, the faster you will travel in that direction. 4. To stop, release the foot pedal and the machine will stop.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Check the drive chain tension and adjust it as necessary. • Check for any loose nuts, bolts, or fittings and tighten them as required. After the first 20 hours • Change the engine oil. • Change the transmission oil. Before each use or daily • Lubricate the drive-roller bearings and the steering heads (lubricate immediately after every washing). • Lubricate the pivot points.
WARNING If you are not careful with hazardous substances, they can cause serious personal injury. • Read the labels and instructions for the materials that you use. • Wear the necessary personal protective safety equipment, and use hazardous substances carefully.
Daily Maintenance Checklist Important: Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat. Sun. Check that pivot joints operate freely. Check the fuel level. Check the engine oil level. Check the transmission oil level. Check the air filter. Clean the engine cooling fins. Check for unusual engine noises. Check for unusual operating noises. Touch up damaged paint.
Lubrication Lubricating the Linkage Pivot Points Lubricating the Drive-roller Bearings and the Steering Heads Service Interval: Before each use or daily Apply a few drops of SAE 30 engine oil or spray lubricant to all the pivot points after cleaning the machine. Important: After oiling, run the machine off the turf somewhere briefly to disperse any excess lubricant, to avoid damaging the turf. Service Interval: Before each use or daily (lubricate immediately after every washing).
Engine Maintenance 3. Remove the oil-filler cap/dipstick by rotating it counterclockwise. Engine Oil 4. Wipe the oil-filler cap/dipstick clean and insert it into the filler port. Crankcase Capacity: 0.60 L (0.63 US qt) Note: Do not screw the dipstick into the port. Type: APl service classification SL, SM, SN, or higher 5. Remove the dipstick and check the oil level. Viscosity: select according to ambient temperature; refer to Figure 12.
1 2 3 4 5 6 G025538 Figure 15 Figure 16 6. Turn the oil drain valve 1/4 turn counterclockwise to start draining the oil (Figure 15). 7. When all the oil is drained, turn the oil drain valve 1/4 turn clockwise to close the valve (Figure 15). 1. Wing nut 4. Paper element 2. Air-cleaner cover 3. Wing nut 5. Foam element 6. Gasket 3. Clean the cover thoroughly. 8. Remove the drain hose and wipe any oil that may have spilled. 4.
1 to distribute oil thoroughly. The foam element should be damp with oil. 2 3 4 8. Clean the paper element by tapping the filter element several times on a hard surface to remove the dirt. Note: Never brush dirt off the element or use compressed air to remove dirt; brushing forces dirt into the fibers and compressed air will damage the paper filter. 9. Install the foam element, the paper element, and the air-cleaner cover. G019300 Figure 18 1. Side electrode 2.
Fuel System Maintenance Cleaning the Sediment Cup Service Interval: Every 100 hours—Clean the sediment cup. DANGER In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. Figure 19 1. Shutoff valve • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any gasoline that spills. 3. Sediment cup 2. O-ring 2.
Drive System Maintenance Checking the Transmission Oil Level Service Interval: Before each use or daily The transmission/tank is filled at the factory with Supersyn 5W-40 synthetic engine oil. Important: Use only Supersyn 5W-40 synthetic engine oil or equivalent engine oils. Other engine oils could cause system damage. 1. Place the machine on a level surface. 2. Check the oil level.
Changing the Transmission Oil Adjusting the Drive Chain Service Interval: After the first 5 hours—Check the drive chain tension and adjust it as necessary. Service Interval: After the first 20 hours Every 800 hours/Every 2 years (whichever comes first) Before each use or daily—Check the drive chain tension and adjust it as necessary. Important: Use only Supersyn 5W-40 synthetic engine oil or equivalent engine oils. Other oils could cause system damage. 1.
Storage • To increase the tension, tighten the tensioning nut. • To decrease the tension, loosen the tensioning nut. 1. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the rollers and the engine. Clean dirt and chaff from the outside of the engine's cylinder head fins and blower housing. Note: If there are not enough threads on the tensioning rod, you can move the locking nut next to the tensioning nut, and use it as a jam nut. 4.
Notes: 26
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
