Installation Instructions

ManualsBrandsToro ManualsTop DressersHopper Vibrator Kit, ProPass Top Dresser and MH-400 Material Delivery Unit

FormNo.3426-889RevA

HopperVibratorKit

ProPassTopDresserandMH-400MaterialDeliveryUnit

ModelNo.44723

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal132-8388

132-8388

1.On2.Off

Installation

Note:Layouttheharnessesonthemachineto

determinethemountinglocationsoftheharness

components.Usetheincludedcabletiestoretainany

surpluscable.Also,ifyouneedtoshortenorlengthen

aharnesssection,usetheincludedwiresplices.Heat

theintegratedheat-shrinktubinguntilitshrinkstight

ontothewires.

Important:Ifyoulengthentheharness,make

suretousethepropergaugeofwire.

PreparingtheMachine

1.Parkthetractionunitandthetopdresseron

alevelsurfaceandlowertheattachments(if

equipped).

2.Engagetheparkingbrake,shutofftheengine,

andremovethekey.

InstallingtheKitona

ProPassTopDresser

InstallingtheSwitchHarnessand

theSwitchonaWorkmanUtility

Vehicle

1.RoutetheswitchharnessshowninFigure4

throughthevehicle,startingatthefront,along

theexistingharness.

Note:Thevibrator-harnessconnectorshould

beintherearofthevehiclenearthehigh-ow

hydraulicsport(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3426-889*A

Summary of content (8 pages)

PAGE 1
Form No. 3426-889 Rev A Hopper Vibrator Kit ProPass Top Dresser and MH-400 Material Delivery Unit Model No. 44723 Installation Instructions Safety Installation Safety and Instructional Decals Note: Lay out the harnesses on the machine to Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. determine the mounting locations of the harness components.
PAGE 2
g031580 Figure 1 Switch harness 3. Vibrator-harness connector 1. Switch connector 2. Power-harness connector 2. Insert the switch, with the rounded side up, into the hole in the dash panel and connect the harness to the switch (Figure 2 and Figure 4). g031583 Figure 3 1. Switch decal Installing the Power Harness 1. Connect the fuse-block connector (Figure 4) to the fuse block of the vehicle and install a 15 A fuse.
PAGE 3
g031582 Figure 5 Battery harness (optional) 1. Switch-harness connector 3. Positive terminal (red wire) 2. Fuse 4. Ground terminal (black wire) 2. g024368 Figure 7 Connect the grounding terminal to the ground block of the vehicle. 3. Plug the open connector (the switch-harness connector) on the power harness into the open connector (the power-harness connector) on the switch harness. 4. Secure the harness with cable ties, away from any sharp edges. 3. Vibrator 2. Mounting plate 4. Nut (4) 3.
PAGE 4
2. Note: If the fuse block is full, add a new fuse block, connect the fuse-block connector to the new fuse block, then add a 15 A fuse to the new fuse block. Remove a knockout plug from an available switch location on the dash. If no switch locations are available, install the switch bracket as follows: A. Find an empty space on the dash to accommodate the switch bracket, and drill 2 holes (7 mm or 9/32 inch) in the dash.
PAGE 5
Note: Locate 1 hole, then use the mounting plate as a template for drilling the remaining holes. g031585 Figure 14 1. Switch-harness connector 4. 2. Vibrator connector Use cable ties to secure all the wires along the hydraulic lines all the way to the switch-harness connector. Note: Ensure that the harness is kept away from any sharp edges. 5. Connect the switch harness to the other end of the vibrator harness. g031587 Figure 12 1. 4.1 cm (1-5/8 inches) 4. 12.7 cm (5 inches) 2. 76.
PAGE 6
Installing the Kit on an MH-400 Material Handler with an Outcross 9060 Traction Unit 1. Cut off and discard the switch-harness connector and strip 10 mm (3/8 inch) of insulation off the wires (Figure 15). Installing the Wire Harness Note: Following these instructions allows you to use the accessory switch that is already installed on the dashboard of the Outcross 9060 traction unit, wired through the 7-pin connection. g272997 Figure 15 1.
PAGE 7
4. Insert the wires through the small hole in the boot. 5. Install the black wire to the pin 1 terminal and the white wire to the pin 7 terminal (Figure 17). 6. Tighten the screws to secure the wires. 7. Assemble the 7-pin connector. Installing the Vibrator 1. g024368 Drill 4 mounting holes (7 mm or 9/32 inch) on the side of the hopper. Refer to Figure 18 for the drilling dimensions. Figure 19 Note: Locate 1 hole, then use the mounting plate as a template for drilling the remaining holes. 1.
PAGE 8
Operation Using the Hopper Vibrator Press the top of the switch to turn the vibrator on (Figure 21, Figure 22, or Figure 23). Press the bottom of the switch to turn the vibrator off. g273085 Figure 23 Tractor g267694 Figure 21 Outcross 9060 Traction Unit 1. On 1. Switch g031588 Figure 22 Workman Vehicle 1. On 2. Off 8 2.