FORM NO. 01-502-0410 ELWOOD No. 4452520101 & up , BEe B AERIE | O MODEL NO. 4453220101 & UP MANUAL MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according fo the instructions in this manual. Toto also wains to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged to read this manual, especially ail the safety instructions, DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS 3-4 SAFETY AND INSTRUCTION DECALS .. 5 SPECIFICATIONS . .. 8 BEFORE OPERATING 7-11 Attach Blower To 300 Series Grounds master 7 Attach Blower To 200 Series Grounds master 811 OPERATING INSTRUCTIONS 12 LUBRICATION TROUBLESHOOTING STORAGE IDENTIFICATION AND ORDERING . MAINTENANCE CHART PROPRIETORSHIP SAFETY INSTRUCTIONS The safety alert symbol means CAUTION, WARNING OR DANGER*personal safety instruction.
SAFETY INSTRUCTIONS (Continued) 8. Operator must be skilled and trained in how to drive on hillsides. Failures to use caution on slopes or hills may cause loss of control! possibly resulting in personal injury or death. 9. If engine stalls or machine loses headway and cannot make it to the top of a slope, do not turn machine around. Always back slowly straight down the slope. 10. Do not carry passengers on the machine or Grounds master and keep everyone away from the areas of operation. 11.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. Replace any decals that becomes . damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor. A DANGER DISCHARGED AIR HAS CONSIDERABLE FORCE AND COULD CAUSE INJURY OR LOSS OF FOOTING @ STAY AWAY FROM DISCHARGE OPENING WHEN Ll ey # KEEP BYSTANDERS AWAY FROM DISCHARGE OPENING WHEN MACHINE 1S RUNNING. ON DEFLECTOR (Part No.
SPECIFICATIONS POWER: PTO from Grounds master CASTORS: Swivel castors 4.10x35x 4 FRAME: All welded steel construction BEARINGS: 2 self sealed and self aligning IMPELLER: 10 bladed, 24" diameter, welded and balanced DIRECTIONAL CHUTE: (Standard) All steel over center locking, spring loaded DIMENSIONS: Height: 36" Length: 36", 24" without handle Width: 46" with directional chute in down position SHIPPING WEIGHT: 245 lbs. CFM: Approx.
BEFORE OPERATING ATTACH BLOWER TO 300 SERIES GROUNDS MASTERS (Fig. 1) A WARNING « Left hand push arm on Grounds master is spring loaded. + Sudden release of the push arm could cause serious personal injury. « Keep hands and face away from arm when it is held and blocked in the downward position. + Use a helper and a wooden block to hold push arm down during installation of accessory. 1. Remove cutting unit or other attachment from Grounds master. Refer to cutting unit or attachment operator's manual. 2.
BEFORE OPERATING (Continued) 10. Secure the bolts on the left ift arm. 11. Secure the boils on the right lift arm. 12. Have a helper push down the left push arm; then remove the 2" x 4" blocks of wood. 13. Have a helper push down the right push arm; then remove the 2" x 4" blocks of wood. 14, Attach the PTO of the Grounds master to the PTQ Adapter on the blower fan shaft. 15. Using the lift mechanism on the Grounds master, lower the unit on a level surface. 16. Practice raising and lowering the blower.
BEFORE OPERATING (Continued) GROUNDS MASTER 220 & 224 (Fig. 3) 4. Attach the Support Bracket (A) to the left side of the steering column housing using existing holes. Secure with 1/4" x 1" bolts. 5. Attach the Lower Support Arm (B) to the front rail of the Grounds master. Secure with 3/8" x bolts. © DEBRIS BLOWER 2670 GROUNDS MASTER GROUNDS MASTER 220-D and 223-D (Fig. 4) 6. Attach the Support Bracket (A} to the steering column housing. Secure the bottom four holes with 3/8 x 1 1/2" bolts.
BEFORE OPERATING (Continued) ONE PIECE CARRIER FRAME ALL 200 SERIES (Fig. 5) 7. Remove the fight arms from the Grounds master. Refer to the mowing deck Operator's Manual. 8. Install the Mounting Frame to the lower tube (A) on the blower using the dower mounting pin to attach. Secure on both ends with the presto pins. 9. Slide the Mounting Frame under the Grounds master. DEBRIS BLOWER 2670 GROUNDS MASTER 10 10. Line up the holes in the Grounds master with the holes in the Mounting Frame (B).
BEFORE OPERATING (Continued) TWO PIECE CARRIER FRAME ALL 200 13. Line up the holes in the Mounting Frame (B) to SERIES (Fig. 6) the right and left lift arms on the Grounds master. 12, Install the Mounting Frame to the lower tube {A) on the blower using the lower mounting pin to attach. Secure on both ends with the presto pins. 14. Secure with the existing bolts on the Grounds master.
OPERATING INSTRUCTIONS 1. Start the Grounds master and run tallow RPM. TRANSPORTING BLOWER 2. Lower the blower using the Grounds master lift 1. Lower the engine speed to idle position. mechanism. 2. Disengaged the PTO and wait for the PTO 3. Engage the PTO while the engine is at idle to come to a complete stop. speed. . 3. Raise the blower to transport position, 4, Bring the PTO speed to full speed or 1800 RPM. 5. Practice blowing material.
TROUBLESHOOTING CONDITION CAUSE CORRECTION FAN QUIT TURNING 1. {200 Series)Remove guard. Check for broken belt or tension of the belt. 2. (200 Series) Check to see if tower pulley is still turning. Bearing pressed in the bearing mount may be damaged. 3. (300 Series) Check PTQ adapter tor sheared blat. 1. Replace belt or adjust the tension of the adjustments in manual) 2. Replace the bearing, use #609 locate when replacing. 3. Replace bolt. 1. Check bearings on fan shaft for EXCESSIVE VIBRATION . * 1.
STORAGE 1. Thoroughly clean the blower. The fan housing should be free of dirt, leaves and debris. 2. Lubricate all grease fittings. Wipe off any excess lubricant. 3. Place a light coat of grease on the splines of the PTO adapter. 4. Tighten all fasteners. IDENTIFICATION AND ORDERING MODEL AND SERIAL NUMBER. The BLOWER 2670 has two identification numbers: a model number and serial number. The two numbers are stamped on a plate which is located on the housing.
If you leaf your TOR product is defective and wish to rely on The Toto Promise, the following procedure is recommended: 1. Can tact your Authorized TOR Distributor or Commercial Dealer (the Yellow Pages of your telephone directory is a goad reference source). 2. The TOR Distributor or Commercial Dealer will advise you on-they arrangements that can be made to inspect and repair your product. 3.