FORM NO. 01-502-1360Rev. A OPERATOR’S MANUAL ICON ADAPTER KIT J Retrofits Bushman@ vicon® Spreader To Tare Workman™ MODEL NO.
FOREWORD Thank you for buying a high quality Toto turf care product. To get the best performance from this machine, operate and maintain it according to the instructions in this manual. Toto also wants to stress the importance of safety. You and anyone else using or maintaining this machine are strongly urged to read this manual, especially all the safety instructions. DANGER, WARNING and CAUTION, used with the triangular safety alert symbol, highlight safety messages.
TABLE OF CONTENTS Page SAFETY INSTRUCTIONS 3-4 MAINTENANCE SAFETY AND INSTRUCTION DECALS 5 STORAGE SET UP INSTRUCTIONS IDENTIFICATION AND ORDERING BEFORE OPERATING THE TOR PROMISE OPERATING INSTRUCTIONS . 12-14 SAFETY INSTRUCTIONS The safety alert symbol means CAUTION, WARNING or DANGER "personal safety instuction™. Read and understand the instruction because it has o do with safety. Failure to comply with the instruction may resulting personal injury. BEFORE OPERATING 1.
SAFETY INSTRUCTIONS (Continued) WHILE OPERATING 10. Operator and passenger should remain seated whenever the vehicle is in motion. 11. NEVER file the hopper with more than 700 Ibs. of material. 12. Using the machine demands attention. Failure to operate vehicle safely may resulting a accident, tip over of vehicle and serious injury or death. Drive carefully. To prevent tipping or loss of control: A.
SAFETY AND INSTRUCTION DECALS The following safety and instruction decals are installed on the unit. Replace any decal that becomes damaged or illegible. Part numbers for decals are listed below and in your Parts Catalog. Order replacements from your Authorized Toto Distributor, DANG GUARDS ARE IN PLACE, RT3 LEVER LR R hellhole WITH SAND BELT COVER & COVER-BACK PLATE {Part No. 01-506-0040} FRONT & REAR OF HOPPER {Loose part, install during assembly) (Part No.
SET UP INSTRUCTIONS IMPORTANT: The Icon Adapter Kit (44240) fits on the Bushman No. 403 Icon Spreader(888401) IMPORTANT: There are several kits that must be installed on the Toto Workman before attaching the Icon Spreader. Follow installation instructions in the Toto Operator’'s Manual for each of the kits.
SET UP INSTRUCTIONS (Continued) WORKMAN PTO Shield ICON {St rage) Main Frame R { = \, Bracket Attachment Mount Figure 2 Clovis & Lynch Pins Rear Stabilizer Bar
SET UP INSTRUCTIONS (Continued) ICON — Pulley Shaft Main Frame ™\ Pensioner Tidier Puffy idler Pulley / Pensioner ~ 4 p BELT ROUTING Center line WORKMAN PTO Adapter Drive Shaft Drive Belts .
SET UP INSTRUCTIONS (Continued) ATTACHING BUSHMAN ICON SPREADER TO WORKMAN (Fig. 2 & 3} IMPORTANT: ALWAYS store the Workman PTO Guard on the Bushman Icon after removal from the Workman. Always replace the Workman PTO Guard on the Workman Vehicle when Bushman Icon Spreader is removed. {See Fig. 2) 1. Remove the Full or 2/3rd bed from the Workman. Remove Rear Pto Guard and store on Icon Cover. (See Workman and bed operator’s manual’s for procedure.) 2.
SET UP INSTRUCTIONS (Continued) ATTACHING HANDLE ASSEMBLY (Fig. Place the Control Handle through the tubing on the Handle Mount Secure with a cotter pin, 18. Attach the Handle Mount 10 the back of the bending to assure lever rotates completely. seat on the Workman as shown in Fig. 4. Use existing Workman fasteners.
SET UP INSTRUCTIONS (Continued) 20. Attach the Bracket Lever to the Icon Control Rod as shown in Fig. 4. Secure with cotter pin. Attach the other end to the tube on the Icon front tube assembly (Fig. 4 and 5). 21. Attach the Control Link to the Control Handle and the Bracket Lever. Use 3/8" bolts and secure enough to allow the link to pivot. To set the Adjustment Bolt: A. Puttee Control Handle back until the Icon metering plate is in the closed position. B.
BEFORE OPERATING CALCULATE LOAD WEIGHT To calculate goad weight: 1. Determine density of material to be spread. {Ibsen) 2. Determine maximum volume. {Volume =700/ Density} 3. Fife hopper LEVEL FULL up to the matching volume line on hopper. DO NOT OVERFILL. 4, NEVER fill past 7 cubic foot line with sand. 5. Volumes indicated are with level material in hopper, NOT heaped. A DANGER NEVER exceed 700 Ibs. of material in the hopper. Serious injury or death could occur from tip overs. Calculate load and use decal.
OPERATING INSTRUCTIONS (Continued) 8. Slowly release clutch pedal and brake pedal. Workman will begin 1o move and Icon will begin to spread material, 9. Depress the accelerator pedal to desired RPM. 10. Move control handle forward/down to open metering gate and dispense material. Move control handle rearward/up to stop spreading. 11. Place PTO in OFF position when finished spreading. IMPORTANT: Do not engage PTO while moving. Damage will occur to PTO. Always stop vehicle before engaging PTO.
OPERATING INSTRUCTIONS (Continued) If engine stalls or you lose headway on a hill, never attempt to turn vehicle around. Always back straight down a hill in reverse gear. NEVER back down in neutral or with the clutch depressed,using only the brakes. NEVER drive across a steep hill, always drive straight up or down. Avoid turning on shill. Don't "drop the clutch”or tam on the brakes. Sudden speed change can initiate tip over. A\ caution Using attachments with high inertia {i.e.
SEASONAL STORAGE 1. Thoroughly clean the Icon Spreader and the 2. Tighten all fasteners. Toto Workman. Follow alt the guidelines for storage in the respective Operator’s Manual. 3. Lubricate all grease fittings and bearings. Wipe off excess (lubricant. IDENTIFICATION AND ORDERING To order replacement parts from an authorized 2. Bushman Icon Spreader parts should be TOR Distributor, supply the following information: obtained from an authorized Bushman parts supplier. 1.
he Toto Promise A ONE YEAR LIMITED WARRANTY The Toto Company promises to repair your TOR Product if defective in materials or workmanship. The Hollowing time periods from the duet of purchase apply: Commercial Products The costs of parts and labor are included, but the customer pays the transportation costs on walk rotary mowers with cutting widths of less than 25". if you feel your TOR product is defective and wish to rely on The Toto Promise, the following procedure is recommended: 1.