FORM NO. 92-0260 MODEL NO. 41400-30101 & UP MODEL NO. 41403-30101 & UP MODEL & UP MODEL NO, 41150-30101 & UP SET-UP AND PARTS LIST SKID SPREADER Refer to the illustrated Parts Lists assembling the Spreader Mounting Kit "Right* and “Left as used in the following instructions, refer to the operator’s right and left when operating the transport Vehicle, Likewise, “Front” and “Rex” as seen from the operator‘s position! The Flow Control Kit (Model No. 41403) is an optional accessory.
FRAME ASSEMBLY: IMPORTANT! Note the position of the Engine Mounting Frame on the plates of the Skid’'s upright Engine Mounts. These plates must be as far toward the REAR of the kid as the fasteners will allow. See Figure 2. 1. Remove the four 5/16* screws to remove the Spreader Mounting Kit’s Drive ({over and set the Cover aside. 2. Remove five 1/4" screws and remove the Belt Shield from the Skid frame and set the Belt Shield aside.
SPREADER INSTALLATION: 1. Place the Spreader Assembly onto the Skid Frame. Use lager thinner to remove the rust preventive coating from the Spreader’s in-put shaft and key way. Insert the 1/4¢ square key into the in-put shaft. 2. Align the Spreader in-put shaft with the End Yoke and slide the Spreader Assembly forward until the End Yoke is fully engaged on the in-put shaft. DO NOT TIGHTEN the set screw at this time. See Figure 4. 3.
OPTIONAL FLOW CONTROL INSTALLATION (PART 2j: 1. Attach the adjustable Clevis on the Actuator Rod to the Flow Regulator Handle (see Figure 7) as follows: 2. Have the Regulator Handle at the "0 position on the ¥low Regulator scale and the Actuator retracted...just short of *ratcheting". If the Rod length is too short to allow the alignment: ® Loosen the jam nut, turn the Adjustable clevis to lengthen the effective length of the Rod. and re-tighten. the.jam. nut.
IMPORTANT! When the optional Flow Control Rit is installed; the top Pin, which is chained to the Flow Regulator, is NOT used in the operation of this unit. Using it as a "stop” for the Regulator Handle will damage the Spreader. The two Limit Switches control the length of the Actuator’s extension or retraction and will have to be adjusted to match the Actuator’s action to the Flow Regulator.
BELT DRIVE INSTALLATION: 1. Install the Drive Belt. The Belt Diagram in Figure 11 illustrates the correct relationship between the Pulleys and the Belt to-Belt Guide clearances. Adjust if necessary, as described below. WITH THE ENGINE TURNED OFF! 2. Pull the Idler Engagement Chain to bring the lexer Pulley into.a position which will exert force on the Drive Belt.
VE: INSTALLING THE SPREADER SAID ON 2 TRANSPORT /@ Position the Skid in the rational that is best suited for the operation of the Ry Spreader, while meeting all of the safety ~CENTER requirements listed below. PUNCH 1. Remove one of the bolts which hold the three square tube Spacers to the Skid. 2. Using the bolt hole as a template, center punch the vehicle bed and replace the bolt. Repeat the procedure at all six hole cola« sons. 3.
SKID SPREADER FRAME MODEL NO. 41400-30101 REF PART NO. DESCRIPTION QTY 1 92-0213 Belt Guard Assembly . evince 1 2 82-0218 Belt Shield N 1 3 34-140-2aMVD Hex Washer Hd. Self Tap Screw 42559 Manual Storage Tube invariant 1 5 42560 Storage Tube Mtg Bret . 2 6 HHS, Cetaceans 10 7 24-11-ad Flat Washer, 3/8 16 8 Lock Washer, 3/8 ..c.iceiuvirnnnsrnreranscars 4 10 Hex Nut, 3/8 NC 9 11 356308 Special Washer e .2 12 92-0216 Spacer Front 358042 Special Washer .. ...
SPREADER FLOW CONTROL MODEL NO. 41403-30101 REF PART NO. DESCRIPTION Query 1 24-13-AD Flat Washer, 1/2 ...iouvevronororornnnoaruana 7 2 92-0302 Adjustable Clevis, 92~0303 Pivot Spacer ..lifesavers 2 4 328967 Hair Pin Cotter 4 5 42195 Clevis Pin, 1/2 x 2" 3 6 22-15-BJKD Hev -Jam Nut, 1/2 NF 2 7 92-0301 Actuator ROd ..ecvcacveas 1 8 42833 Actual «svrvavsenerannenarerenensans 1 8 94485 Muffler Clamp (Incas. C-Bolts & Nuts) e 2 10 92-0297 Mounting Bracket-Limit Switch 1 11 22-11-AGED Hex Nut, 1/4 HC ...
42833 ACTUATOR ® DESCRIPTOR REF PART NO TON QTY 1 42844 Cover Tube 1 2 42848 Drive Screw Assembly 1 3 42850 Front Housing e 1 4 42847 Clutch Assembly 1 5 42845 Rear Housing 1 6 42849 MOLOr...vcunn 1 7 42852 Motor Pinion Gear .